Low-molecular-weight model study of peroxide cross-linking of ethylene-propylene-diene rubber using gas chromatography and mass spectrometry II. Addition and combination reactions.

The dicumyl-peroxide-initiated addition and combination reactions of mixtures of alkanes (n-octane, n-decane) and alkenes [5,6-dihydrodicyclopentadiene (DCPDH), 5-ethylidene-2-norbornane (ENBH) and 5-vinylidene-2-norbornane (VNBH)] were studied to mimic the peroxide cross-linking reactions of terpolymerised ethylene, propylene and a diene monomer (EPDM). The reaction products of the mixtures were separated by both gas chromatography (GC) and comprehensive two-dimensional gas chromatography (GCxGC). The separated compounds were identified from their mass spectra and their GC and GCxGC elution pattern. Quantification of the various alkyl/alkyl, alkyl/allyl and allyl/allyl combination products shows that allylic-radicals comprise approximately 60% of the substrate radicals formed. The total concentration of the products formed by combination is found to be independent of the concentration and the type of alkene. The total concentration of the products formed by addition to the alkene increases with increasing concentration of alkene. In addition, the total concentration of the formed addition products depends strongly on the type of the alkene used, viz. VNBH>ENBH approximately DCPDH, which is a consequence of differences in steric hindrance of the unsaturation. The peroxide curing efficiency, defined as the number of moles of cross-linked products formed per mol of peroxide, is 173% using 9% (w/w) 5-vinylidene-2-norbornane (VNBH). This indicates that the addition reaction is recurrent. All these findings are consistent with experimental studies on peroxide curing of EPDM rubber. In addition, the present results provide more-detailed structural information, increasing the understanding of the mechanism of peroxide curing of EPDM. The described approach to use low-molecular-weight model compounds followed by GC-mass spectrometry (MS) and GCxGC-MS analysis is proven to be a very powerful tool to study the cross-linking of EPDM.

Low-molecular-weight model study of peroxide cross-linking of ethylene-propylene (-diene) rubber using gas chromatography and mass spectrometry I. Combination reactions of alkanes.

The combination reaction of linear and branched alkanes, initiated by dicumylperoxide, has been studied as a model for the combination cross-linking reaction of peroxide-cured terpolymerised ethylene, propylene and diene monomer. Both gas chromatography-mass spectrometry (GC-MS) and comprehensive two-dimensional GC-MS (GCxGC-MS) analyses have been employed to analyse the isomeric reaction products. The identification of these products based on their MS fragmentation patterns is quite complex, due to the high tendency of random rearrangements. Careful elucidation of the high-mass ions at optimised ionisation energy (55eV) has resulted in proposed structures for the different isomeric reaction products. The structure assignment by MS is in agreement with the GCxGC elution pattern and with the result of a theoretical model to predict the boiling points and, thus, the GC retention times. In addition, a model that provided a direct correlation between chemical structure and retention times was developed and this was found to provide a useful fit. Quantification of the identified reaction products by GC separation and flame ionization detection allows classification according to the hydrogen abstraction sites for the alkanes by dicumylperoxide. The selectivity for hydrogen abstraction generally follows the expected order, but a higher reactivity was observed for the methylene group next to a primary methyl group, while a reduced reactivity of the methylene group next to ethyl and to methyl groups was observed. The used approach proved to be a very powerful tool to enhance our understanding of the mechanism of peroxide cross-linking of (branched) alkanes.

Characterisation of UV-cured acrylate networks by means of hydrolysis followed by aqueous size-exclusion combined with reversed-phase chromatography.

UV-cured networks prepared from mixtures of di-functional (polyethylene-glycol di-acrylate) and mono-functional (2-ethylhexyl acrylate) acrylates were analysed after hydrolysis, by aqueous size-exclusion chromatography coupled to on-line reversed-phase liquid-chromatography. The mean network density and the fraction of dangling chain ends of these networks were varied by changing the concentration of mono-functional acrylate. The amount and the molar-mass distribution of the polyethylene-glycol chains between cross-links (M(XL)) and polyacrylic acid (PAA) backbone chains (the so-called kinetic chain length (kcl)) in the different acrylate networks were determined quantitatively. The molar-mass distribution of kcl revealed an almost linear dependence on the concentration of mono-functional acrylate. Analysis of the starting materials showed a significant concentration of mono-functional polyethylene-glycol acrylate. In combination with the analysis of the extractables of the UV-cured networks (polymers not attached to the network, impurities that originate from the photo-initiator and unreacted monomers), more insight in the total network structure was obtained. It was shown that the UV-cured networks contain only small fractions of residual compounds. With these results, the chemical network structure for the different UV-cured acrylate polymers was expressed in network parameters such as the number of PAA units which are cross-linked, the degree of cross-linking, and the network density, which is the molar concentration of effective network chains between cross-links per volume of the polymers. The mean molar mass of chains between chemical network junctions (M(C)) was calculated and compared with results obtained from solid-state NMR and DMA. The mean molar mass of chains between network junctions as determined by these methods was similar.

On-line determination of carboxylic acids, aldehydes and ketones by high-performance liquid chromatography-diode array detection-atmospheric pressure chemical ionisation mass spectrometry after derivatization with 2-nitrophenylhydrazine.

2-Nitrophenylhydrazine (2-NPH) is widely used for the derivatization of carboxylic acids, aldehydes and ketones, in industrial and biological samples. These compounds react with 2-NPH to form derivatives, which are separated by high-performance liquid chromatography (HPLC) and detected with diode array detection (DAD). The UV spectra give information about the functionality of the compounds: carboxylic acid or ketone/aldehyde. Most of the eluting compounds in "known" samples are well characterised by the retention time (comparison with those of standards) of the 2-NPH derivative and their UV spectrum. The identification of different unknown 2-NPH derivatives of carboxylic acids, ketones and/or aldehydes, in industrial or biological samples, based on retention time and/or UV spectrum is not sufficient. These unknown 2-NPH compounds can be identified with on-line atmospheric pressure chemical ionisation mass spectrometry (APCI-MS) based on the molecular mass or/and the fragmentation of the derivative. A novel and specific on-line HPLC-DAD-APCI(-)-MS method is described for the determination of carboxylic acids, ketones and aldehydes, after on-line pre-column derivatization with 2-NHP. The fragmentation of different 2-NPH derivatives were investigated and the possibilities of APCI(-)-MS detection were demonstrated by the on-line identification of an unknown derivative, which turned out to be a side product between 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide hydrochloride and 2-NPH in the presence of high concentrations of a cyclic amide in the sample solution.

Analysis of linear and cyclic oligomers in polyamide-6 without sample preparation by liquid chromatography using the sandwich injection method. III. Separation mechanism and gradient optimization.

The first six linear and cyclic oligomers of polyamide-6 can be quantitatively determined in the polymer using HPLC with the sandwich injection method and an aqueous acetonitrile gradient. In this final part of the triptych concerning the determination of the oligomers in polyamide-6, the irregular elution behavior of the cyclic monomer compared to the cyclic oligomers was investigated. We also optimized the separation of the involved polyamide oligomers, with respect to gradient steepness, stationary phase, column temperature and mobile phase pH. The irregular elution behavior of the cyclic monomer could be caused by its relatively large exposed/accessible hydrophobic surface, which permits relatively easy penetration into the hydrophobic stationary phase giving extra retention. The dipole moment of the different oligomers was used as a measure for this exposed/accessible hydrophobic area to correlate the retention factors using quantitative structure-retention relationships. We also studied the retention behavior of the polyamide, which is injected each run directly onto the column and modifies the stationary phase. Using a 250-microl post gradient injection zone of formic acid on a 250x3 mm Zorbax SB-C18 column, the polyamide could be effectively removed from the stationary phase after each separation. The linear solvent strength (LSS) model was used to optimize the separation of the first six linear and cyclic oligomers. As the LSS model assumes a linear correlation between the modifier concentration and the logarithm of the retention factor and the cyclic monomer and dimer show extreme curvation of this relation in the eluting region, we investigated different models to predict gradient elution from isocratic data. A direct translation of the isocratic data to gradient retention times did not yield adequate retention times using the LSS model. It was found that the LSS model worked acceptably if gradient retention times were used as input data. Even for fast non-linearly eluting components, an average error of 0.4 resolution units of 4sigma was obtained. Using the LSS model in combination with different column temperatures and mobile phase pH values, a separation of the first six linear and cyclic oligomers was accomplished.

Quantitation of functionality of poly(methyl methacrylate) by liquid chromatography under critical conditions followed by evaporative light-scattering detection. Comparison with NMR and titration.

Atom transfer radical polymerisation (ATRP) is a versatile 'living' controlled polymerisation technique for the synthesis of well-defined architectures such as block copolymers, gradient copolymers, hyperbranched polymers and telechelic polymers. ATRP provides control over molecular mass and molecular mass distribution and is suitable for the polymerisation of a wide variety of monomers, including methyl methacrylate. A chromatographic method was developed for an endgroup-based separation of low-molecular-mass poly(methyl methacrylate) (PMMA), based on liquid chromatography under critical conditions. With this method the PMMA, irrespective of its low-molecular-mass, is separated according to endgroups (functionality) due to interactions of the polar endgroups with the non-modified silica based stationary phase. The different series were identified using on-line atmospheric pressure ionisation electrospray mass spectrometry and quantified by evaporative light scattering detection. These results were compared with those obtained by NMR and titration.

Endgroup-based separation and quantitation of polyamide-6,6 by means of critical chromatography.

Polyamide-6,6 is a polycondensation product from the two monomers adipic acid and 1,6-hexamethylenediamine. Depending on the reacted amount of these monomers, different ratios of amine and carboxylic acid endgroups can be formed. Besides linear chains, cyclic polyamides will also be formed. Using critical chromatography, polyamide-6,6 can be separated independently of molar mass. Retention is based solely on endgroup functionality. It is demonstrated that high-molecular-mass polyamide-6,6 (Mw approximately 20,000-30,000) can be separated using this approach. The separation was optimized by using different parameters, such as percentage modifier, temperature and pressure. The concentration of phosphoric acid was used for selective retention of the different endgroup functionalities. Using this property, a new method called critical gradient chromatography was performed where the mobile phase changes from a weak to a strong solvent with respect to the endgroup functionality, while retaining the critical conditions of the backbone unit. Quantification using UV detection is discussed.

Advances in the evaluation of the stability and characteristics of the amino acid and amine derivatives obtained with the o-phthaldialdehyde/3-mercaptopropionic acid and o-phthaldialdehyde/N-acetyl-L-cysteine reagents. High-performance liquid chromatography-mass spectrometry study.

The composition of the amino acid and amine derivatives obtained with the o-phthaldialdehyde (OPA)/3-mercaptopropionic acid (MPA) and with the OPA/N-acetyl-L-cysteine (NAC) reagents was investigated by on-line HPLC-electrospray ionization MS. The initially formed derivatives proved to be, as expected, the corresponding isoindoles while their transformed species contained one additional OPA molecule. Based on the MS spectra of all transformed OPA derivatives a reaction pathway is suggested. This reaction mechanism was supported both by the molecular ions of the endproducts and by the presence of several selective fragment ions that served as an explanation to the structure of the believed to be less stable OPA derivatives. It has been shown that more than one OPA derivative forms in all those cases when the compound to be derivatized does contain the NH2-CH2-R moiety. Thus, amino acids like e.g. glycine, histidine, beta-alanine, gamma-aminobutyric acid, epsilon-aminocaproic acid, ornithine, and also several aliphatic mono- and diamines provide more than one OPA derivative. Analytical consequences of this experience were utilized by altering the reagent's composition. Reagents containing mole ratios of [OPA]/[MPA] or [OPA]/[NAC]=1/50 resulted in two benefits, simultaneously: (i) in a decrease of the transformation rate of the initially formed derivative, and, (ii) in an increase of the overall stability of the total of derivatives.

Separation and quantification of the linear and cyclic structures of polyamide-6 at the critical point of adsorption.

The linear and cyclic structures of polyamide-6 were separated by liquid chromatography at critical conditions (LCCC) and identified with different mass spectrometric (MS) techniques and quantitated by LCCC with evaporative light-scattering detection (ELSD). Electrospray ionization MS was not suitable to identify the higher cyclic structures. For this purpose, matrix-assisted laser desorption ionization time-of-flight MS performed better and cyclic and linear structures were oligomerically resolved and separately identified in the mass spectrometer. The highest cyclic structure present and detected was the cyclic pentacontamer. It could be demonstrated that cyclic and linear oligomers follow different ionization and fragmentation routes/patterns. Quantification with ELSD of the components separated by LCCC using a universal calibration curve or an iterative procedure was developed. An area correction to account for different peak widths of coeluting components improves precision and accuracy of the calibration curve and improves quantitation accuracy for the samples analyzed. With these corrected values, no molecular mass dependency was observed for the cyclic and linear structures. Under critical conditions, the linear and cyclic structures of polyamide-6 were separated, identified and quantified.

Analysis of linear and cyclic oligomers in polyamide-6 without sample preparation by liquid chromatography using the sandwich injection method. II. Methods of detection and quantification and overall long-term performance.

By separating the first six linear and cyclic oligomers of polyamide-6 on a reversed-phase high-performance liquid chromatographic system after sandwich injection, quantitative determination of these oligomers becomes feasible. Low-wavelength UV detection of the different oligomers and selective post-column reaction detection of the linear oligomers with o-phthalic dicarboxaldehyde (OPA) and 3-mercaptopropionic acid (3-MPA) are discussed. A general methodology for quantification of oligomers in polymers was developed. It is demonstrated that the empirically determined group-equivalent absorption coefficients and quench factors are a convenient way of quantifying linear and cyclic oligomers of nylon-6. The overall long-term performance of the method was studied by monitoring a reference sample and the calibration factors of the linear and cyclic oligomers.

Analysis of linear and cyclic oligomers in polyamide-6 without sample preparation by liquid chromatography using the sandwich injection method. I. Injection procedure and column stability.

We report a method for reliable routine polymer sample introduction with minimal bias, a separation method of the first six linear and cyclic oligomers by liquid chromatography, quantification using group equivalents and long term method performance. Injecting a polymer sample in a mobile phase containing an aqueous non-solvent often results in blocked systems as the polymer precipitates in the connecting capillaries. In this first part we focus on a new injection technique, in which the dissolved polyamide is placed between two zones of formic acid, preventing the polymer to precipitate before it reaches the column. Development of this sandwich injection method makes direct injection of the polymer into an aqueous acetonitrile gradient feasible. The oligomeric polyamide recovery of this technique, extraction, dissolution/precipitation and direct injection on a hexafluoro-isopropanol (HFIP) gradient were compared. With the sandwich injection method the polymer remains on the column, slowly changing the stationary phase. The influence of this on resolution and retention was studied. Column stability allows sixty injections before cleaning or replacing the column is necessary.

Analysis of higher polyamide-6 oligomers on a silica-based reversed-phase column with a gradient of formic acid as compared with hexafluoroisopropanol.

The analysis of polyamide-6 oligomers and polymer is usually performed with expensive fluorinated alcohols like 2,2,2-trifluoroethanol (TFE) or 1,1,1,3,3,3-hexafluoroisopropanol (HFIP). Formic acid is well known as a mobile phase additive to adjust pH in reversed-phase high-performance liquid chromatography. However, formic acid is seldom used as a modifier to perform gradient elution chromatography on octadecyl-modified silica-based columns. Here we demonstrate the determination of cyclic and linear polyamide-6 oligomers using formic acid as a modifier on an octadecyl-modified silica-based column. This column was shown to be stable for more than 5000 column volumes, even when a mobile phase of 65-95% formic acid in water at a flow of 1 ml/min is applied. With formic acid under the conditions used (65-95% formic acid in water) the oligomers are retained on the column, while the polymer does not precipitate. In comparison, during adsorption and separation with a HFIP gradient, precipitation of the polymer occurs. The implications of the different separation mechanisms, i.e., adsorption vs. precipitation chromatography are discussed. Loadability is shown to be much better with the formic acid system. However, with formic acid as a modifier UV detection below 250 nm is not feasible. The less sensitive evaporative light scattering detector is used to detect the polyamide oligomers in the formic acid phase. In addition it is shown that capillary zone electrophoresis (CZE) with UV-absorbance detection using HFIP is an attractive combination as HFIP is UV-transparent and CZE allows low modifier consumption.

Optimization of the separation of the Rp and Sp diastereomers of phosphate-methylated DNA and RNA dinucleotides.

The separation by reversed-phase high-performance liquid chromatography of Rp and Sp diastereomers of phosphate-methylated DNA and RNA dinucleotides was studied with respect to pH, organic modifier type and concentration and reversed-phase packing material. Drylab G was used to deduce optimum conditions. On the basis of the observed discrepancies between the computer predictions and experimental results, the gradient operation procedure with volatile buffers was improved. By repetitive chromatography on a 250 x 22 mm I.D. reversed-phase column, fourteen diastereomeric pairs were obtained in at least 97% purity and 60% yield, in amounts of 10-100 mg.