Hydroxyapatite-loaded macroporous calcium alginate hydrogels: Preparation, characterization, and in vitro evaluation.

Hydrogels from natural polysaccharides are of great interest for tissue engineering. This study aims (1) to prepare hydroxyapatite-loaded macroporous calcium alginate hydrogels by novel one-step technique using internal gelation in water-frozen solutions; (2) to evaluate their physicochemical properties; (3) to estimate their ability to support cell growth and proliferation in vitro. The structure of the hydrogel samples in a swollen state was studied by confocal laser scanning microscopy and was shown to represent a system of interconnected macropores with sizes of tens micron. The swelling behavior of the hydrogels, their mechanical properties (Young's moduli) in function of a hydroxyapatite content (5-30 mass%) were studied. All hydrogel samples loaded with hydroxyapatite were found to support growth and proliferation of mouse fibroblasts (L929) at long-term cultivation for 7 days. The obtained macroporous composite Ca-Alg-HA hydrogels could be promising for tissue engineering.

Activity of zinc oxide and zinc borate nanoparticles against resistant bacteria in an experimental lung cancer model.

BACKGROUND: Recent research indicates a prevalence of typical lung infections, such as pneumonia, in lung cancer patients. Klebsiella pneumoniae, Pseudomonas aeruginosa, and Acinetobacter baumannii stand out as antibiotic-resistant pathogens. Given this, there is a growing interest in alternative therapeutic avenues. Boron and zinc derivatives exhibit antimicrobial, antiviral, and antifungal properties. OBJECTIVES: This research aimed to establish the effectiveness of ZnO and ZB NPs in combating bacterial infections in lung cancer cell lines. METHODS: Initially, this study determined the minimal inhibitory concentration (MIC) and fractional inhibitory concentration (FIC) of zinc oxide nanoparticles (ZnO NPs) and zinc borate (ZB) on chosen benchmark strains. Subsequent steps involved gauging treatment success through a lung cancer-bacteria combined culture and immunohistochemical analysis. RESULTS: The inhibitory impact of ZnO NPs on bacteria was charted as follows: 0.97 µg/mL for K. pneumoniae 700603, 1.95 µg/mL for P. aeruginosa 27853, and 7.81 µg/mL for Acinetobacter baumannii 19,606. In comparison, the antibacterial influence of zinc borate was measured as 7.81 µg/mL for Klebsiella pneumoniae 700603 and 500 µg/mL for both P. aeruginosa 27853 and A.baumannii 19606. After 24 h, the cytotoxicity of ZnO NPs and ZB was analyzed using the MTT technique. The lowest cell viability was marked in the 500 µg/mL ZB NPs group, with a viability rate of 48.83% (P < 0.001). However, marked deviations appeared at ZB concentrations of 61.5 µg/mL (P < 0.05) and ZnO NPs at 125 µg/mL. CONCLUSION: A synergistic microbial inhibitory effect was observed when ZnO NP and ZB were combined against the bacteria under investigation.

Gel Based on Hydroxyethyl Starch with Immobilized Amikacin for Coating of Bone Matrices in Experimental Osteomyelitis Treatment.

A polysaccharide gel containing covalently bound amikacin, a broad-spectrum antibiotic, was produced by using epichlorohydrin-activated hydroxyethyl starch (HES). The structure of the polymers was analyzed by 13C and 1H nuclear magnetic resonance (13C NMR and 1H NMR) and matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF) mass spectrometry. The sites of covalent attachment of amikacin to the epoxypropyl substituent and the HES backbone were determined. The antibacterial activity of the polymer was evaluated in vitro using the agar well diffusion method with the Staphylococcus aureus P209 strain. It was demonstrated that the polymer retained activity in the presence of bacterial amylase, which is released upon bacterial attack. The gel was applied for coating pores and surfaces of a biocomposite material based on a xenogenic bovine bone matrix. In vivo experiments showed the effectiveness of utilizing amikacin-containing biocomposite bone-substitute materials in the treatment of experimental osteomyelitis in rats using objective histological control and X-ray tomography.

Promising Gene Delivery Properties of Polycations Based on 2-(N,N-dimethylamino)ethyl Methacrylate and Polyethylene Glycol Monomethyl Ether Methacrylate Copolymers.

Cationic copolymers based on 2-(N,N-dimethylamino)ethyl methacrylate and polyethylene glycol monomethyl ether (pDMAEMA-co-PEO) with different molecular weights have been synthesized. Their physicochemical properties were studied by NMR spectroscopy, sedimentation, and potentiometric titration. According to the data of potentiometric titration for the synthesized pegylated cationic copolymers, the apparent dissociation constants were determined in the pH range from 4.5 to 8.5. The physicochemical properties of interpolyelectrolyte complexes of these polycations with circular DNA (IPEC DNA) were also studied by dynamic light scattering, electrophoretic mobility, and TEM methods. It has been established that the diameter and electrokinetic potential (ζ-potential) of interpolyelectrolyte complexes can be varied over a wide range (from 200 nm to 1.5 µm and from -25 mV to +30 mV) by changing the ratio of oppositely charged ionizable groups in pegylated cationic copolymers and DNA, as well as by regulating medium pH. The resistance of the IPEC DNA/polycation complex to the action of nucleases was studied by electrophoresis in agarose gel; the cytotoxic effect of the polymers in vitro, and the efficiency of penetration (transfection) of IPEC DNA with PDMAEMA-co-PEO-polycations into eukaryotic cells of a cell line derived from human embryonic kidneys HEK 293 in vitro.

One-Pot Synthesis of Colloidal Hybrid Au (Ag)/ZnO Nanostructures with the Participation of Maleic Acid Copolymers.

One-pot synthesis of colloidal Au/ZnO and Ag/ZnO nanohybrid structures was carried out. The copolymers of maleic acid-poly(N-vinyl-2-pyrrolidone-alt-maleic acid), poly(ethylene-alt-maleic acid), or poly(styrene-alt-maleic acid) were used as templates for the sorption of cations of metals-precursors and stabilization of the resulting nanoheterostructures. Simultaneous production of two types of nanoparticles has been implemented under mild conditions in an aqueous alkaline medium and without additional reagents. Equimolar ratios of the metal cations and appropriate load on all copolymers were used: molar ratio of maleic acid monomeric units of copolymer/gold (silver)cations/zinc cations was 1/0.15/0.23 (1/0.3/0.15). The process of obtaining the heterostructures was studied using UV-Vis spectroscopy. The kinetics of the formation of heterostructures was influenced by the nature of the maleic acid copolymer and noble metal cations used. A high reaction rate was observed in the case of using zinc and gold cations-precursors and a copolymer of maleic acid with N-vinylpyrrolidone as a stabilizer of nanoparticles. The structure of the synthesized polymer-stabilized heterostructures was studied using instrumental methods of analysis-XPS, FTIR, PXRD, and TEM. Under the conditions used, stable colloidal solutions of heterodimers were obtained, and such structure can be converted to a solid state and back without loss of properties.

Branched Amphiphilic Polylactides as a Polymer Matrix Component for Biodegradable Implants.

The combination of biocompatibility, biodegradability, and high mechanical strength has provided a steady growth in interest in the synthesis and application of lactic acid-based polyesters for the creation of implants. On the other hand, the hydrophobicity of polylactide limits the possibilities of its use in biomedical fields. The ring-opening polymerization of L-lactide, catalyzed by tin (II) 2-ethylhexanoate in the presence of 2,2-bis(hydroxymethyl)propionic acid, and an ester of polyethylene glycol monomethyl ester and 2,2-bis(hydroxymethyl)propionic acid accompanied by the introduction of a pool of hydrophilic groups, that reduce the contact angle, were considered. The structures of the synthesized amphiphilic branched pegylated copolylactides were characterized by 1H NMR spectroscopy and gel permeation chromatography. The resulting amphiphilic copolylactides, with a narrow MWD (1.14-1.22) and molecular weight of 5000-13,000, were used to prepare interpolymer mixtures with PLLA. Already, with the introduction of 10 wt% branched pegylated copolylactides, PLLA-based films had reduced brittleness, hydrophilicity, with a water contact angle of 71.9-88.5°, and increased water absorption. An additional decrease in the water contact angle, of 66.1°, was achieved by filling the mixed polylactide films with 20 wt% hydroxyapatite, which also led to a moderate decrease in strength and ultimate tensile elongation. At the same time, the PLLA modification did not have a significant effect on the melting point and the glass transition temperature; however, the filling with hydroxyapatite increased the thermal stability.

Fe3O4 Nanoparticles in Combination with 5-FU Exert Antitumor Effects Superior to Those of the Active Drug in a Colon Cancer Cell Model.

(1) Background: Colon cancer is one of the most common cancer types, and treatment options, unfortunately, do not continually improve the survival rate of patients. With the unprecedented development of nanotechnologies, nanomedicine has become a significant direction in cancer research. Indeed, chemotherapeutics with nanoparticles (NPs) in cancer treatment is an outstanding new treatment principle. (2) Methods: Fe3O4 NPs were synthesized and characterized. Caco-2 colon cancer cells were treated during two different periods (24 and 72 h) with Fe3O4 NPs (6 µg/mL), various concentrations of 5-FU (4−16 µg/mL), and Fe3O4 NPs in combination with 5-FU (4−16 µg/mL) (Fe3O4 NPs + 5-FU). (3) Results: The MTT assay showed that treating the cells with Fe3O4 NPs + 5-FU at 16 µg/mL for 24 or 72 h decreased cell viability and increased their LDH release (p < 0.05 and p < 0.01, respectively). Furthermore, at the same treatment concentrations, total antioxidant capacity (TAC) was decreased (p < 0.05 and p < 0.01, respectively), and total oxidant status (TOS) increased (p < 0.05 and p < 0.01, respectively). Moreover, after treatment with Fe3O4-NPs + 5-FU, the IL-10 gene was downregulated and PTEN gene expression was upregulated (p < 0.05 and p < 0.01, respectively) compared with those of the control. (4) Conclusions: Fe3O4 NPs exert a synergistic cytotoxic effect with 5-FU on Caco-2 cells at concentrations below the active drug threshold levels.

Mixture of Anthraquinone Sulfo-Derivatives as an Inexpensive Organic Flow Battery Negolyte: Optimization of Battery Cell.

Anthraquinone-2,7-disulfonic acid (2,7-AQDS) is a promising organic compound, which is considered as a negolyte for redox flow batteries as well as for other applications. In this work we carried out a well-known reaction of anthraquinone sulfonation to synthesize 2,7-AQDS in mixture with other sulfo-derivatives, namely 2,6-AQDS and 2-AQS. Redox behavior of this mixture was evaluated with cyclic voltammetry and was almost identical to 2,7-AQDS. Mixture was then assessed as a potential negolyte of anthraquinone-bromine redox flow battery. After adjusting membrane-electrode assembly composition (membrane material and flow field)), the cell demonstrated peak power density of 335 mW cm-2 (at SOC 90%) and capacity utilization, capacity retention and energy efficiency of 87.9, 99.6 and 64.2%, respectively. These values are almost identical or even higher than similar values for flow battery with 2,7-AQDS as a negolyte, while the price of mixture is significantly lower. Therefore, this work unveils the promising possibility of using a mixture of crude sulfonated anthraquinone derivatives mixture as an inexpensive negolyte of RFB.

Nanoaggregates of Biphilic Carboxyl-Containing Copolymers as Carriers for Ionically Bound Doxorubicin.

Application of nanocarriers for drug delivery brings numerous advantages, allowing both minimization of side effects common in systemic drug delivery and improvement in targeting, which has made it the focal point of nanoscience for a number of years. While most of the studies are focused on encapsulation of hydrophobic drugs, delivery of hydrophilic compounds is typically performed via covalent attachment, which often requires chemical modification of the drug and limits the release kinetics. In this paper, we report synthesis of biphilic copolymers of various compositions capable of self-assembly in water with the formation of nanoparticles and suitable for ionic binding of the common anticancer drug doxorubicin. The copolymers are synthesized by radical copolymerization of N-vinyl-2-pyrrolidone and acrylic acid using n-octadecyl-mercaptan as a chain transfer agent. With an increase of the carboxyl group's share in the chain, the role of the electrostatic stabilization factor of the nanoparticles increased as well as the ability of doxorubicin as an ion binder. A mathematical description of the kinetics of doxorubicin binding and release is given and thermodynamic functions for the equilibrium ionic binding of doxorubicin are calculated.

Epoxy Compositions with Reduced Flammability Based on DER-354 Resin and a Curing Agent Containing Aminophosphazenes Synthesized in Bulk Isophoronediamine.

A method for the synthesis of an amine-containing epoxy resin curing agent by dissolving hexakis-[(4-formyl)phenoxy]cyclotriphosphazene in an excess of isophoronediamine was developed. The curing agent was characterized via NMR and IR spectroscopy and MALDI-TOF mass spectrometry, and its rheological characteristics were studied. Compositions based on DER-354 epoxy resin and the synthesized curing agent with different amounts of phosphazene content were obtained. The rheological characteristics of these compositions were studied, followed by their curing. An improvement in several thermal (DSC), mechanical (compression, tension, and adhesion), and physicochemical (water absorption and water solubility) characteristics, as well as the fire resistance of the obtained materials modified with phosphazene, was observed, compared with unmodified samples. In particular, there was an improvement in adhesive characteristics and fire resistance. Thus, compositions based on a curing agent containing a 30% modifier were shown to fulfill the V-1 fire resistance category. The developed compositions can be processed by contact molding, winding, and resin transfer molding (RTM), and the resulting material is suitable for use in aircraft, automotive products, design applications, and home repairs.

Hybrid (Bovine Serum Albumin)/Poly(N-vinyl-2-pyrrolidone-co-acrylic acid)-Shelled Microbubbles as Advanced Ultrasound Contrast Agents.

Microbubbles are routinely used ultrasound contrast agents in the clinic. While a soft protein shell is commercially preferable for imaging purposes, a rigid polymer shell demonstrates prolonged agent stability. Hence, combining polymers and proteins in one shell composition can advance microbubble properties. We formulated the hybrid "protein-copolymer" microbubble shell with a complex of bovine serum albumin and an amphiphilic copolymer of N-vinyl-2-pyrrolidone and acrylic acid. The resulting microbubbles demonstrated advanced physicochemical and acoustic properties, preserving in vitro biocompatibility. Adjusting the mass ratio between protein and copolymer allowed fine tuning of the microbubble properties of concentration (by two orders, up to 1010 MBs/mL), mean size (from 0.8 to 5 µm), and shell thickness (from 28 to 50 nm). In addition, the minimum air-liquid surface tension for the "protein-copolymer" solution enabled the highest bubble concentration. At the same time, a higher copolymer amount in the bubble shell increased the bubble size and tuned duration and intensity of the contrast during an ultrasound procedure. Demonstrated results exemplify the potential of the hybrid "protein-polymer" microbubble shell, allowing tailoring of microbubble properties for image-guided applications, combining advances of each material involved in the formulation.

Nanoparticle-Containing Wound Dressing: Antimicrobial and Healing Effects.

The dressings containing nanoparticles of metals and metal oxides are promising types of materials for wound repair. In such dressings, biocompatible and nontoxic hydrophilic polymers are used as a matrix. In the present review, we take a look at the anti-microbial effect of the nanoparticle-modified wound dressings against various microorganisms and evaluate their healing action. A detailed analysis of 31 sources published in 2021 and 2022 was performed. Furthermore, a trend for development of modern antibacterial wound-healing nanomaterials was shown as exemplified in publications starting from 2018. The review may be helpful for researchers working in the areas of biotechnology, medicine, epidemiology, material science and other fields aimed at the improvement of the quality of life.

Synthesis of Amphiphilic Copolymers of N-Vinyl-2-pyrrolidone and Allyl Glycidyl Ether for Co-Delivery of Doxorubicin and Paclitaxel.

Co-delivery of chemotherapeutics in cancer treatment has been proven essential for overcoming multidrug resistance and improving the outcome of therapy. We report the synthesis of amphiphilic copolymers of N-vinyl-2-pyrrolidone and allyl glycidyl ether of various compositions and demonstrate that they can form nanoaggregates capable of simultaneous covalent immobilization of doxorubicin by the epoxy groups in the shell and hydrophobic-driven incorporation of paclitaxel into the core of nanoparticles. The structure of the obtained copolymers was characterized by 13C NMR, IR, and MALDI spectroscopy, as well as adsorption at the water/toluene interface. A linear increase in the number-average molecular weight of amphiphilic copolymers and a decrease in the number-average diameter of macromolecular aggregates with an increase in the ratio N-vinyl-2-pyrrolidone/allyl glycidyl ether were observed. The assembled nanocarriers were characterized by DLS. The reported novel nanocarriers can be of interest for delivery and co-delivery of a wide range of pharmacological preparations and combined therapy for cancer and other deceases.

Polymeric Dental Nanomaterials: Antimicrobial Action.

This review aims to describe and critically analyze studies published over the past four years on the application of polymeric dental nanomaterials as antimicrobial materials in various fields of dentistry. Nanoparticles are promising antimicrobial additives to restoration materials. According to published data, composites based on silver nanoparticles, zinc(II), titanium(IV), magnesium(II), and copper(II) oxide nanoparticles, chitosan nanoparticles, calcium phosphate or fluoride nanoparticles, and nanodiamonds can be used in dental therapy and endodontics. Composites with nanoparticles of hydroxyapatite and bioactive glass proved to be of low efficiency for application in these fields. The materials applicable in orthodontics include nanodiamonds, silver nanoparticles, titanium(IV) and zinc(II) oxide nanoparticles, bioactive glass, and yttrium(III) fluoride nanoparticles. Composites of silver nanoparticles and zinc(II) oxide nanoparticles are used in periodontics, and nanodiamonds and silver, chitosan, and titanium(IV) oxide nanoparticles are employed in dental implantology and dental prosthetics. Composites based on titanium(IV) oxide can also be utilized in maxillofacial surgery to manufacture prostheses. Composites with copper(II) oxide nanoparticles and halloysite nanotubes are promising materials in the field of denture prosthetics. Composites with calcium(II) fluoride or phosphate nanoparticles can be used in therapeutic dentistry for tooth restoration.

Formation of Hydrogels Based on a Copolymer of N-Vinyl-2-pyrrolidone and Glycidyl Methacrylate in the Presence of the Reaction Product of 1,3-Dimethylmidazolium Dimethylphosphate and Elemental Sulfur.

The aim of the study is to search for a reaction that provides the possibility of tandem "one-pot" formation of polymer networks during radical copolymerization of N-vinyl-2-pyrrolidone and glycidyl methacrylate. It was shown that the addition of recently synthesized 1,3-dimethylimidazolium (phosphonooxy-)oligosulfanide makes it possible to obtain a cross-linked copolymer in one stage as a result of radical copolymerization of N-vinyl-2-pyrrolidone and glycidyl methacrylate with a molar ratio of monomers less than 1.4. The structure of the copolymerization products of N-vinyl-2-pyrroldione and glycidyl methacrylate formed in the presence of 1,3-dimethylimidazolium (phosphonooxy-)oligosulfanide was characterized by 1H NMR, FTIR and MALDI spectroscopy. 1H NMR spectroscopy revealed an interaction under moderate heating between glycidyl methacrylate and 1,3-dimethylimidazolium (phosphonooxy-)oligosulfanide, accompanied by the formation of a mixture of unsaturated products of complex structure, presumably acting as crosslinking agents. It is shown that when the molar ratio of N-vinyl-2-pyrroldione/glycidyl methacrylate comonomers is 0.89, a densely crosslinked copolymer is formed, capable of limited swelling in water with a velocity constant of 5.06 × 10-2 min-1 and an equilibrium degree of swelling of about 227%.

A Degradable Inverse Vulcanized Copolymer as a Coating Material for Urea Produced under Optimized Conditions.

Global enhancement of crop yield is achieved using chemical fertilizers; however, agro-economy is affected due to poor nutrient uptake efficacy (NUE), which also causes environmental pollution. Encapsulating urea granules with hydrophobic material can be one solution. Additionally, the inverse vulcanized copolymer obtained from vegetable oils are a new class of green sulfur-enriched polymer with good biodegradation and better sulfur oxidation potential, but they possess unreacted sulfur, which leads to void generations. In this study, inverse vulcanization reaction conditions to minimize the amount of unreacted sulfur through response surface methodology (RSM) is optimized. The copolymer obtained was then characterized using Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). FTIR confirmed the formation of the copolymer, TGA demonstrated that copolymer is thermally stable up to 200 °C temperature, and DSC revealed the sulfur conversion of 82.2% (predicted conversion of 82.37%), which shows the goodness of the model developed to predict the sulfur conversion. To further maximize the sulfur conversion, 5 wt% diisopropenyl benzene (DIB) as a crosslinker is added during synthesis to produce terpolymer. The urea granule is then coated using terpolymer, and the nutrient release longevity of the coated urea is tested in distilled water, which revealed that only 65% of its total nutrient is released after 40 days of incubation. The soil burial of the terpolymer demonstrated its biodegradability, as 26% weight loss happens in 52 days of incubation. Thus, inverse vulcanized terpolymer as a coating material for urea demonstrated far better nutrient release longevity compared with other biopolymers with improved biodegradation; moreover, these copolymers also have potential to improve sulfur oxidation.

Synthesis, Self-Assembly and In Vitro Cellular Uptake Kinetics of Nanosized Drug Carriers Based on Aggregates of Amphiphilic Oligomers of N-Vinyl-2-pyrrolidone.

Development of nanocarrier-based drug delivery systems is a major breakthrough in pharmacology, promising targeted delivery and reduction in drug toxicity. On the cellular level, encapsulation of a drug substantially affects the endocytic processes due to nanocarrier-membrane interaction. In this study we synthesized and characterized nanocarriers assembled from amphiphilic oligomers of N-vinyl-2-pyrrolidone with a terminal thiooctadecyl group (PVP-OD). It was found that the dissolution free energy of PVP-OD depends linearly on the molecular mass of its hydrophilic part up to M¯n = 2 × 104, leading to an exponential dependence of critical aggregation concentration (CAC) on the molar mass. A model hydrophobic compound (DiI dye) was loaded into the nanocarriers and exhibited slow release into the aqueous phase on a scale of 18 h. Cellular uptake of the loaded nanocarriers and that of free DiI were compared in vitro using glioblastoma (U87) and fibroblast (CRL2429) cells. While the uptake of both DiI/PVP-OD nanocarriers and free DiI was inhibited by dynasore, indicating a dynamin-dependent endocytic pathway as a major mechanism, a decrease in the uptake rate of free DiI was observed in the presence of wortmannin. This suggests that while macropinocytosis plays a role in the uptake of low-molecular components, this pathway might be circumvented by incorporation of DiI into nanocarriers.

Novel chitosan and bacterial cellulose biocomposites tailored with polymeric nanoparticles for modern wound dressing development.

Dressing biomaterials play a key role in wound management keeping a moisture medium and protecting against external factors. Natural and synthetic materials could be used as dressings where chitosan and bacterial cellulose is one of the most important solutions. These biopolymers have been used for wound dressing based on their non-toxic, biodegradable, and biocompatible features. In this study, biocomposites based on bacterial cellulose and chitosan membranes tailored with antimicrobial loaded poly(N-isopropylacrylamide)/polyvinyl alcohol nanoparticles were prepared. Core-shell polymeric nanoparticles, bacterial cellulose/chitosan membranes, and biocomposites were independently loaded with silver sulfadiazine, a well-known sulfonamide antibacterial agent used in the therapy of mild-to-moderate infections for sensitive organisms. The chemistry, structure, morphology, and size distribution were investigated by Fourier transformed infrared spectroscopy (FTIR-ATR), RAMAN spectroscopy, Scanning electron (SEM) and Transmission electron microscopy (TEM), and Dynamic light scattering (DLS). In vitro release behaviors of silver sulfadiazine from polymeric nanoparticles and biocomposites were investigated. The biological investigations revealed good biocompatibility of both the nanoparticles and the biocomposites in terms of human dermal fibroblasts viability and proliferation potential. Finally, the drug-loaded polymeric biomaterials showed promising characteristics, proving their high potential as an alternative support to develop a biocompatible and antibacterial wound dressing.

Kinetics and Mechanism of Synthesis of Carboxyl-Containing N-Vinyl-2-Pyrrolidone Telehelics for Pharmacological Use.

It was found that sulfanylethanoic and 3-sulfanylpropanoic acids are effective regulators of molecular weight with chain transfer constants of 0.441 and 0.317, respectively, and show an unexpected acceleration effect on the radical polymerization of N-vinyl-2-pyrrolidone, initiated by 2,2'-azobisisobutyronitrile. It was determined for the first time that the thiolate anions of mercapto acids form a high-temperature redox initiating system with 2,2'-azobisisobutyronitrile during the radical polymerization of N-vinyl-2-pyrrolidone in 1,4-dioxane. Considering the peculiarities of initiation, a kinetic model of the polymerization of N-vinyl-2-pyrrolidone is proposed, and it is shown that the theoretical orders of the reaction rate, with respect to the monomer, initiator, and chain transfer agent, are 1, 0.75, 0.25, and are close to their experimentally determined values. Carboxyl-containing techelics of N-vinyl-2-pyrrolidone were synthesized so that it can slow down the release of the anticancer drug, doxorubicin, from aqueous solutions, which can find its application in the pharmacological field.

Chemical Oxidative Polymerization of Methylene Blue: Reaction Mechanism and Aspects of Chain Structure.

The kinetic regularities of the initial stage of chemical oxidative polymerization of methylene blue under the action of ammonium peroxodisulfate in an aqueous medium have been established by the method of potentiometry. It was shown that the methylene blue polymerization mechanism includes the stages of chain initiation and growth. It was found that the rate of the initial stage of the reaction obeys the kinetic equation of the first order with the activation energy 49 kJ × mol-1. Based on the proposed mechanism of oxidative polymerization of methylene blue and the data of MALDI, EPR, and IR spectroscopy methods, the structure of the polymethylene blue chain is proposed. It has been shown that polymethylene blue has a metallic luster, and its electrical conductivity is probably the result of conjugation over extended chain sections and the formation of charge transfer complexes. It was found that polymethylene blue is resistant to heating up to a temperature of 440 K and then enters into exothermic transformations without significant weight loss. When the temperature rises above 480 K, polymethylene blue is subject to endothermic degradation and retains 75% of its mass up to 1000 K.