Amplification factor in DC insulator-based electrokinetic devices: a theoretical, numerical, and experimental approach to operation voltage reduction for particle trapping.

Insulator-based microfluidic devices are attractive for handling biological samples due to their simple fabrication, low-cost, and efficiency in particle manipulation. However, their widespread application is limited by the high operation voltages required to achieve particle trapping. We present a theoretical, numerical, and experimental study that demonstrates these voltages can be significantly reduced (to sub-100 V) in direct-current insulator-based electrokinetic (DC-iEK) devices for micron-sized particles. To achieve this, we introduce the concept of the amplification factor-the fold-increase in electric field magnitude due to the presence of an insulator constriction-and use it to compare the performance of different microchannel designs and to direct our design optimization process. To illustrate the effect of using constrictions with smooth and sharp features on the amplification factor, geometries with circular posts and semi-triangular posts were used. These were theoretically approximated in two different systems of coordinates (bipolar and elliptic), allowing us to provide, for the first time, explicit electric field amplification scaling laws. Finite element simulations were performed to approximate the 3D insulator geometries and provide a parametric study of the effect of changing different geometrical features. These simulations were used to predict particle trapping voltages for four different single-layer microfluidic devices using two particle suspensions (2 and 6.8 µm in size). The general agreement between our models demonstrates the feasibility of using the amplification factor, in combination with nonlinear electrokinetic theory, to meet the prerequisites for the development of portable DC-iEK microfluidic systems.

Fine-Tuning Electrokinetic Injections Considering Nonlinear Electrokinetic Effects in Insulator-Based Devices.

The manner of sample injection is critical in microscale electrokinetic (EK) separations, as the resolution of a separation greatly depends on sample quality and how the sample is introduced into the system. There is a significant wealth of knowledge on the development of EK injection methodologies that range from simple and straightforward approaches to sophisticated schemes. The present study focused on the development of optimized EK sample injection schemes for direct current insulator-based EK (DC-iEK) systems. These are microchannels that contain arrays of insulating structures; the presence of these structures creates a nonuniform electric field distribution when a potential is applied, resulting in enhanced nonlinear EK effects. Recently, it was reported that the nonlinear EK effect of electrophoresis of the second kind plays a major role in particle migration in DC-iEK systems. This study presents a methodology for designing EK sample injection schemes that consider the nonlinear EK effects exerted on the particles being injected. Mathematical modeling with COMSOL Multiphysics was employed to identify proper voltages to be used during the EK injection process. Then, a T-microchannel with insulating posts was employed to experimentally perform EK injection and separate a sample containing two types of similar polystyrene particles. The quality of the EK injections was assessed by comparing the resolution (Rs) and number of plates (N) of the experimental particle separations. The findings of this study establish the importance of considering nonlinear EK effects when planning for successful EK injection schemes.

On the potential of microscale electrokinetic cascade devices.

Phages used for phage therapy of multidrug resistant bacteria must be highly purified prior to use. There are limited purification approaches that are broadly applicable to many phage types. Electrokinetics has shown great potential to manipulate phages, but obstructions from the cell debris produced during phage propagation can severely diminish the capacity of an electrokinetic device to concentrate and purify phage samples. A multipart insulator-based electrokinetic device is proposed here to remove the larger, undesirable components of mixtures from phage preparations while transferring the freshly purified and concentrated sample to a second stage for downstream analysis. By combining the large debris prescreen and analysis stages in a streamlined system, this approach simultaneously reduces the impact of clogging and minimizes the sample loss observed during manual transferring of purified samples. Polystyrene particles were used to demonstrate a diminished sample loss of approximately one order of magnitude when using the cascade device as opposed to a manual transfer scheme. The purification and concentration of three different phage samples were demonstrated using the first stage of the cascade device as a prescreen. This design provides a simple method of purifying and concentrating valuable samples from a complex mixture that might impede separation capacity in a single channel.

Creation of an electrokinetic characterization library for the detection and identification of biological cells.

The rising concern over drug-resistant microorganisms has increased the need for rapid and portable detection systems. However, the traditional methods for the analysis of microorganisms can be both resource and time intensive. This contribution presents an alternative approach for the characterization of microorganisms using a microscale electrokinetic technique. The present study aims to develop and validate a library with a novel parameter referred to as the electrokinetic equilibrium condition for each strain, which will allow for fast identification of the studied bacterial and yeast cells in electrokinetic (EK) microfluidic devices. To create the library, experiments with six organisms of interest were conducted using insulator-based EK devices with circle-shaped posts. The organisms included one yeast strain, Saccharomyces cerevisiae; one salmonella strain, Salmonella enterica; two species from the same genus, Bacillus cereus and Bacillus subtilis; and two Escherichia coli strains. The results from these experiments were then analyzed with a mathematical model in COMSOL Multiphysics®, which yielded the electrokinetic equilibrium condition for each distinct strain. Lastly, to validate the applicability EK library, the COMSOL model was used to estimate the trapping conditions needed in a device with oval-shaped posts for each organism, and these values were then compared with experimentally obtained values. The results suggest the library can be used to estimate trapping voltages with a maximum relative error of 12%. While the proposed electrokinetic technique is still a novel approach and the analysis of additional microorganisms would be needed to expand the library, this contribution further supports the potential of microscale electrokinetics as a technique for the rapid and robust characterization of microbes. Graphical abstract.

Rapid Escherichia coli Trapping and Retrieval from Bodily Fluids via a Three-Dimensional Bead-Stacked Nanodevice.

A novel micro- and nanofluidic device stacked with magnetic beads has been developed to efficiently trap, concentrate, and retrieve Escherichia coli (E. coli) from the bacterial suspension and pig plasma. The small voids between the magnetic beads are used to physically isolate the bacteria in the device. We used computational fluid dynamics, three-dimensional (3D) tomography technology, and machine learning to probe and explain the bead stacking in a small 3D space with various flow rates. A combination of beads with different sizes is utilized to achieve a high capture efficiency (∼86%) with a flow rate of 50 µL/min. Leveraging the high deformability of this device, an E. coli sample can be retrieved from the designated bacterial suspension by applying a higher flow rate followed by rapid magnetic separation. This unique function is also utilized to concentrate E. coli cells from the original bacterial suspension. An on-chip concentration factor of ∼11× is achieved by inputting 1300 µL of the E. coli sample and then concentrating it in 100 µL of buffer. Importantly, this multiplexed, miniaturized, inexpensive, and transparent device is easy to fabricate and operate, making it ideal for pathogen separation in both laboratory and point-of-care settings.