Hybrid BOFDA/BOCDA system for distributed static and dynamic strain measurements.

We present a distributed optical fiber sensor based on a hybrid Brillouin optical frequency/correlation-domain analysis (BOFDA/BOCDA) configuration for both static and dynamic strain measurements. Distributed static strain (or temperature) measurements are realized using the conventional BOFDA method, i.e., acquiring the baseband transfer function of the fiber through a vector network analyzer (VNA). With little modifications, the same setup can perform dynamic, position-selective measurements synthesizing a correlation peak through a frequency modulation of the laser source while operating the VNA at a single modulation frequency. Experimental tests, carried out at a sampling frequency up to 40 Hz and a spatial resolution of ≈5 cm, demonstrate the validity of the proposed approach.

Distributed Temperature Sensing through Network Analysis Frequency-Domain Reflectometry.

In this paper, we propose and demonstrate a network analysis optical frequency domain reflectometer (NA-OFDR) for distributed temperature measurements at high spatial (down to ≈3 cm) and temperature resolution. The system makes use of a frequency-stepped, continuous-wave (cw) laser whose output light is modulated using a vector network analyzer. The latter is also used to demodulate the amplitude of the beat signal formed by coherently mixing the Rayleigh backscattered light with a local oscillator. The system is capable of attaining high measurand resolution (≈50 mK at 3-cm spatial resolution) thanks to the high sensitivity of coherent Rayleigh scattering to temperature. Furthermore, unlike the conventional optical-frequency domain reflectometry (OFDR), the proposed system does not rely on the use of a tunable laser and therefore is less prone to limitations related to the laser coherence or sweep nonlinearity. Two configurations are analyzed, both numerically and experimentally, based on either a double-sideband or single-sideband modulated probe light. The results confirm the validity of the proposed approach.

Tuning of the Brillouin scattering properties in microstructured optical fibers by liquid infiltration.

We demonstrate the possibility to modify the Brillouin scattering properties of a microstructured pure-silica core optical fiber, by infiltrating a liquid inside its holes. In particular, we show that the dependence of the Brillouin frequency shift (BFS) on the temperature can be reduced by infiltration, owing to the large negative thermo-optic coefficient of the liquid. Infiltrating a chloroform-acetonitrile mixture with a refractive index of 1.365 inside the holes of a suspended-core fiber with a core diameter of 3 µm, the BFS temperature sensing coefficient is reduced by ≈ 21%, while the strain sensitivity remains almost unaltered. Besides tuning the temperature sensing coefficient, the proposed platform could find other applications in Brillouin sensing, such as distributed electrical and magnetic measurements, or enhanced Brillouin gain in fibers infiltrated with high nonlinear optical media.

Innovative Photonic Sensors for Safety and Security, Part II: Aerospace and Submarine Applications.

The employability of photonics technology in the modern era's highly demanding and sophisticated domain of aerospace and submarines has been an appealing challenge for the scientific communities. In this paper, we review our main results achieved so far on the use of optical fiber sensors for safety and security in innovative aerospace and submarine applications. In particular, recent results of in-field applications of optical fiber sensors in aircraft monitoring, from a weight and balance analysis to vehicle Structural Health Monitoring (SHM) and Landing Gear (LG) monitoring, are presented and discussed. Moreover, underwater fiber-optic hydrophones are presented from the design to marine application.

Innovative Photonic Sensors for Safety and Security, Part I: Fundamentals, Infrastructural and Ground Transportations.

Our group, involving researchers from different universities in Campania, Italy, has been working for the last twenty years in the field of photonic sensors for safety and security in healthcare, industrial and environment applications. This is the first in a series of three companion papers. In this paper, we introduce the main concepts of the technologies employed for the realization of our photonic sensors. Then, we review our main results concerning the innovative applications for infrastructural and transportation monitoring.

Innovative Photonic Sensors for Safety and Security, Part III: Environment, Agriculture and Soil Monitoring.

In order to complete this set of three companion papers, in this last, we focus our attention on environmental monitoring by taking advantage of photonic technologies. After reporting on some configurations useful for high precision agriculture, we explore the problems connected with soil water content measurement and landslide early warning. Then, we concentrate on a new generation of seismic sensors useful in both terrestrial and under water contests. Finally, we discuss a number of optical fiber sensors for use in radiation environments.

Automated Damage Detection Using Lamb Wave-Based Phase-Sensitive OTDR and Support Vector Machines.

In this paper, we propose and demonstrate a damage detection technique based on the automatic classification of the Lamb wave signals acquired on a metallic plate. In the reported experiments, Lamb waves are excited in an aluminum plate through a piezoelectric transducer glued onto the monitored structure. The response of the monitored structure is detected through a high-resolution phase-sensitive optical time-domain reflectometer (ϕ-OTDR). The presence and location of a small perturbation, induced by placing a lumped mass of 5 g on the plate, are determined by processing the optical fiber sensor data through support vector machine (SVM) classifiers trained with experimental data. The results show that the proposed method takes full advantage of the multipoint sensing nature of the ϕ-OTDR technology, resulting in accurate damage detection and localization.

Lamb Wave Detection for Structural Health Monitoring Using a ϕ-OTDR System.

In this paper, the use of a phase-sensitive optical time-domain reflectometry (ϕ-OTDR) sensor for the detection of the Lamb waves excited by a piezoelectric transducer in an aluminum plate, is investigated. The system is shown to detect and resolve the Lamb wave in distinct regions of the plate, opening the possibility of realizing structural health monitoring (SHM) and damage detection using a single optical fiber attached to the structure. The system also reveals the variations in the Lamb wave resulting from a change in the load conditions of the plate. The same optical fiber used to detect the Lamb waves has also been employed to realize distributed strain measurements using a Brillouin scattering system. The method can be potentially used to replace conventional SHM sensors such as strain gauges and PZT transducers, with the advantage of offering several sensing points using a single fiber.

Long-Term Monitoring of a Tunnel in a Landslide Prone Area by Brillouin-Based Distributed Optical Fiber Sensors.

This paper shows the results of the monitoring of the deformations of a tunnel, carried out using a distributed optical fiber strain sensor based on stimulated Brillouin scattering. The artificial tunnel of the national railway crosses the accumulation zone of an active landslide, the Varco d'Izzo earthflow, in the southern Italian Apennines. Severely damaged by the landslide movements, the tunnel was demolished and rebuilt in 1992 as a reinforced concrete box flanked by two deep sheet pile walls. In order to detect the onset of potentially dangerous strains of the tunnel structure and follow their time trend, the internal deformations of the tunnel are also monitored by a distributed fiber-optic strain sensor since 2016. The results of the monitoring activity show that the deformation profiles are characterized by strain peaks in correspondence of the structural joints. Furthermore, the elongation of the fiber strands crossing the joints is consistent with the data derived by other measurement systems. Experiments revealed an increase in the time rate of the fiber deformation in the first and last part of the monitoring period when the inclinometers of the area also recorded an acceleration in the landslide movements.

Distributed Optical Fiber Sensor Applications in Geotechnical Monitoring.

We report the experimental application of distributed optical fiber sensors, based on stimulated Brillouin scattering (SBS), to the monitoring of a small-scale granular slope reconstituted in an instrumented flume and subjected to artificial rainfall until failure, and to the monitoring of a volcanic rock slope. The experiments demonstrate the sensors' ability to reveal the sudden increase in soil strain that foreruns the failure in a debris flow phenomenon, as well as to monitor the fractures in the tuff rocks. This study offers an important perspective on the use of distributed optical fiber sensors in the setting up of early warning systems for landslides in both rock and unconsolidated materials.

The Role of Tapered Light-Diffusing Fibers in Plasmonic Sensor Configurations.

In this work, we experimentally analyzed the effect of tapering in light-diffusing optical fibers (LDFs) when employed as surface plasmon resonance (SPR)-based sensors. Although tapering is commonly adopted to enhance the performance of plasmonic optical fiber sensors, we have demonstrated that in the case of plasmonic sensors based on LDFs, the tapering produces a significant worsening of the bulk sensitivity (roughly 60% in the worst case), against a slight decrease in the full width at half maximum (FWHM) of the SPR spectra. Furthermore, we have demonstrated that these aspects become more pronounced when the taper ratio increases. Secondly, we have established that a possible alternative exists in using the tapered LDF as a modal filter after the sensible region. In such a case, we have determined that a good trade-off between the loss in sensitivity and the FWHM decrease could be reached.

Distributed Static and Dynamic Strain Measurements in Polymer Optical Fibers by Rayleigh Scattering.

We demonstrate the use of a graded-index perfluorinated optical fiber (GI-POF) for distributed static and dynamic strain measurements based on Rayleigh scattering. The system is based on an amplitude-based phase-sensitive Optical Time-Domain Reflectometry (ϕ-OTDR) configuration, operated at the unconventional wavelength of 850 nm. Static strain measurements have been carried out at a spatial resolution of 4 m and for a strain up to 3.5% by exploiting the increase of the backscatter Rayleigh coefficient consequent to the application of a tensile strain, while vibration/acoustic measurements have been demonstrated for a sampling frequency up to 833 Hz by exploiting the vibration-induced changes in the backscatter Rayleigh intensity time-domain traces arising from coherent interference within the pulse. The reported tests demonstrate that polymer optical fibers can be used for cost-effective multiparameter sensing.

A Nanoplasmonic-Based Biosensing Approach for Wide-Range and Highly Sensitive Detection of Chemicals.

In a specific biosensing application, a nanoplasmonic sensor chip has been tested by an experimental setup based on an aluminum holder and two plastic optical fibers used to illuminate and collect the transmitted light. The studied plasmonic probe is based on gold nanograting, realized on the top of a Poly(methyl methacrylate) (PMMA) chip. The PMMA substrate could be considered as a transparent substrate and, in such a way, it has been already used in previous work. Alternatively, here it is regarded as a slab waveguide. In particular, we have deposited upon the slab surface, covered with a nanograting, a synthetic receptor specific for bovine serum albumin (BSA), to test the proposed biosensing approach. Exploiting this different experimental configuration, we have determined how the orientation of the nanostripes forming the grating pattern, with respect to the direction of the input light (longitudinal or orthogonal), influences the biosensing performances. For example, the best limit of detection (LOD) in the BSA detection that has been obtained is equal to 23 pM. Specifically, the longitudinal configuration is characterized by two observable plasmonic phenomena, each sensitive to a different BSA concentration range, ranging from pM to µM. This aspect plays a key role in several biochemical sensing applications, where a wide working range is required.

Two-wavelength phase-sensitive OTDR sensor using perfect periodic correlation codes for measurement range enhancement, noise reduction and fading compensation.

We demonstrate a two-wavelength differential-phase-measuring OTDR sensor that uses perfect periodic correlation phase codes to enhance the measurement performance. The two-wavelength technique extends the measurement range of OTDR sensors by synthesizing a virtual longer-wavelength measurement from two simultaneous measurements of phase using different lasers. This increases the range free from phase unwrapping errors. However, we find that the application of this technique greatly increases the relative measurement noise. To compensate for this issue, we introduce the use of optical pulse compression using perfect periodic correlation phase codes to increase the measurement signal-to-noise ratio and also to facilitate the simultaneous compensation of Rayleigh and polarization fading. In addition, we apply a method to further reduce the relative noise that is added to the two-wavelength measurement by using the synthetic wavelength measurement to unwrap the differential phase measured with a single wavelength. All this is highlighted in a 1-km sensing link in which up to 20-cm spatial resolution and 12.6 pϵ/Hz strain sensitivity are demonstrated as well as a 67-fold enhancement in measurement range compared with the use of the conventional single-wavelength method.

Distributed Dynamic Strain Sensing Based on Brillouin Scattering in Optical Fibers.

Over the past three decades, extensive research activity on Brillouin scattering-based distributed optical fiber sensors has led to the availability of commercial instruments capable of measuring the static temperature/strain distribution over kilometer distances and with high spatial resolution, with applications typically covering structural and environmental monitoring. At the same time, the interest in dynamic measurements has rapidly grown due to the relevant number of applications which could benefit from this technology, including structural analysis for defect identification, vibration detection, railway traffic monitoring, shock events detection, and so on. In this paper, we present an overview of the recent advances in Brillouin-based distributed optical fiber sensors for dynamic sensing. The aspects of the Brillouin scattering process relevant in distributed dynamic measurements are analyzed, and the different techniques are compared in terms of performance and hardware complexity.

An Fiber Bragg Grating-Based Monitoring System for Slope Deformation Studies in Geotechnical Centrifuges.

Centrifugal model tests, which can reproduce the deformation process of the slope, play a crucial role in investigating the mechanism of slope failure. The FBG-based sensors, with high precision, electromagnetic resistance, light weight and small size, have been introduced into geotechnical centrifuge monitoring. The slope evolution is a complex multi-parameter dynamic process which involves the interaction of displacement, stress and strain. However, current research is mainly focused on one or two monitoring aspects, i.e., strain or displacement monitoring to study some specific questions. To achieve multi-parameter and real-time monitoring, a comprehensive fiber Bragg grating (FBG) monitoring system including miniaturized anchors, earth pressure gauges, inclinometer pipe and retaining wall, has been designed for geotechnical centrifuge tests. Before the centrifugal test, laboratory calibrations of sensors were carried out. The calibration results indicate that the FBG-based sensors can monitor the strain, stress and displacement variation precisely. The multi-parameter information related to slope stability were captured and analyzed in detail. The stress state of the anchors, strain distribution of retaining wall together with the displacement of the inclinometer pipe indicate the progressive evolutionary process of the model slope. The test results also indicate that the critical centrifugal force for the transition of the sliding surface is 45 g, after which, a sliding surface is formed in the soil above the retaining wall. The feasibility and validity of the monitoring system is verified by a comparison between the results of FBG-based sensors and those of a numerical simulation. In summary, the innovative FBG-based monitoring system has provided a feasible multi-parameter monitoring method in geotechnical centrifugal tests so as to facilitate further in-depth analysis.

Long-Term Monitoring with Fiber Optics Distributed Temperature Sensing at Campi Flegrei: The Campi Flegrei Deep Drilling Project.

Monitoring volcanic phenomena is a key question, for both volcanological research and for civil protection purposes. This is particularly true in densely populated volcanic areas, like the Campi Flegrei caldera, which includes part of the large city of Naples (Italy). Borehole monitoring of volcanoes is the most promising way to improve classical methods of surface monitoring, although not commonly applied yet. Fiber optics technology is the most practical and suitable way to operate in such high temperature and aggressive environmental conditions. In this paper, we describe a fiber optics Distributed Temperature Sensing (DTS) sensor, which has been designed to continuously measure temperature all along a 500 m. deep well drilled in the west side of Naples (Bagnoli area), lying in the Campi Flegrei volcanic area. It has then been installed as part of the international 'Campi Flegrei Deep Drilling Project', and is continuously operating, giving insight on the time variation of temperature along the whole borehole depth. Such continuous monitoring of temperature can in turn indicate volcanic processes linked to magma dynamics and/or to changes in the hydrothermal system. The developed monitoring system, working at bottom temperatures higher than 100 °C, demonstrates the feasibility and effectiveness of using DTS for borehole volcanic monitoring.

Refractive index sensing by Brillouin scattering in side-polished optical fibers.

In this Letter, we demonstrate the possibility to measure the refractive index of a liquid, using the stimulating Brillouin scattering in a 3-cm-long side-polished optical fiber. In addition, we show that by depositing a high-refractive index layer on the polished surface the sensitivity of the Brillouin frequency shift (BFS) can be increased due to a higher penetration of the evanescent field in the outer medium. Experiments show a maximum BFS change of about 11 MHz when varying the refractive index of the external medium from 1 (air) to 1.402, and a BFS sensitivity to refractive index of about 293 MHz/RIU around 1.40.

Cost-effective method for fast Brillouin optical time-domain analysis.

A new Brillouin optical time-domain analysis (BOTDA) technique for acquiring the full Brillouin gain spectrum (BGS) at high speed is proposed and demonstrated. The method employs a frequency swept microwave source for the generation of the probe wave, so that the entire BOTDA measurement is taken within the duration of the frequency sweep itself. By properly setting the duration of the sweep, the repetition rate of the pump pulses and the number of averages, truly distributed and dynamic measurements of the BGS are possible using a set-up at a fraction of the cost and complexity of the previously reported fast-BOTDA methods.

Proposal of Brillouin optical frequency-domain reflectometry (BOFDR).

We demonstrate a Brillouin optical frequency-domain reflectometry (BOFDR) technique, which can measure the strain and/or temperature along an optical fiber with one-end access, by detecting the spontaneous Brillouin scattering from a sinusoidally modulated pump light. Compared to the Brillouin optical frequency-domain analysis (BOFDA), we show that BOFDR measurements are free from the distorting components related to acoustic wave modulation, thus simplifying data processing.