In vitro comparison of one-step, two-step, and three-step polishing systems on the surface roughness and gloss of different resin composites.

OBJECTIVES: This laboratory study evaluated the effect of three polishing systems on the surface roughness and gloss of resin composites. MATERIALS AND METHODS: Thirty specimens (6 mm Ø × 8 mm) were fabricated from each of three resin composites: Z 350 XT (nanofill), Harmonize (nanohybrid), and Estelite Omega (supranonofill). All specimens were photopolymerized using a multi-peak LED curing unit (VALO-Standard mode), having a exitance irradiance of approximately 1000 mW/cm2 against a polyester strip (PS). 2 mm was then removed from the irradiated end (finished) using #320 abrasive paper (F). Specimens were then randomly polished (P) using a one-step (1S) (OneGloss), two-step (2S) (EVE Diacomp Twist Basic CA), or 3-step (3S) (Astropol P) system (n = 10). For PS, F, and P groups, surface roughness (Ra) was measured using a surface roughness tester, and surface gloss was measured with a glossmeter. For each specimen, the percent recovery to the PS value (%R) of surface roughness and surface gloss were calculated. Data were analyzed using two-way ANOVA, followed by Tukey's test. Surface roughness and gloss values were submitted to Pearson's correlation test (α = 0.05). All statistical testing was performed using a pre-set alpha of 0.05. RESULTS: The interaction term [resin composite × polishing system] was significant for both surface roughness (p = 0.001) and gloss (p = 0.0001). For all resin composites, the 2S and 3S systems provided a higher %R of surface roughness and gloss compared to those of the 1S system. There was a negative correlation between surface roughness and gloss, but only a few combinations showed strong correlations. CONCLUSIONS: The 2S and 3S polishing systems provided surfaces having greater smoothness and gloss compared to the 1S system. The ability to recover surface roughness and gloss was dependent on type of resin composite filler classification. CLINICAL SIGNIFICANCE: The 3S and 2S polishing systems were more effective in achieving PS values than was the 1S system for all tested resin composites. However, individual polishing systems performed differently depending on type of resin composite.

Effectiveness of ultrasonic activation associated to glycolic acid on smear layer removal, dentin structure and bond strength to root dentin

This study evaluated the effects of ultrasonic activation (US) associated to glycolic acid (GA) on smear layer, dentin structure and bond strength (BS) of filling/restorative material to root dentin. The roots were used for antimicrobial activity, dentin structure and BS evaluation, being distributed into seven groups, according to irrigation protocols: G1:DW+US; G2:17% EDTA; G3:QMix; G4:17% GA; G5:17% EDTA+US; G6:QMix+US; G7:17% GA+US. Scanning electronic microscopy, transmission electronic microscopy and push-out were performed, with specific statistical analysis for each evaluation. The highest smear layer removal occured in Groups 6 and 7 (p<0.05), and the largest collagen dispersion in Group 7, being similar to Group 2 and 5 (p>0.05). The highest BS of filling and restorative material occurred in Groups 6 and 7, and Groups 5, 6 and 7, respectively, being similars between them (p>0.05). The use of GA+US promoted effective smear layer removal and dentin structure preservation, improving the BS of filling/restorative material to root dentin.

Microtensile bond strength of CAD/CAM materials to dentin under different adhesive strategies.

The present study aimed to evaluate the microtensile bond strength (µTBS) of novel computer-aided design/computer-aided manufacturing (CAD/CAM) restorative materials to dentin using different adhesive strategies. Thirty-two crowns were milled using CAD/CAM materials (Vita Mark II as control, Vita Suprinity, Vita Enamic and Lava Ultimate) and luted to dentin using different resin cements (RelyX ARC, RelyX Unicem 2 and RelyX Ultimate). The specimens were stored in 100% relative humidity at 37°C for 24 h and sectioned. The samples (n = 16) with cross-sectional areas of approximately 0.90 mm2, were submitted to a µTBS test in a universal testing machine with a crosshead speed of 0.5 mm/min. The samples were analyzed with SEM to determinate the failure mode. According to 2-way ANOVA and Tukey's test (α=0.05), the interaction effect (material x luting strategy) was significant (p=0.001). Regardless of the luting strategy, a higher µTBS was obtained with Lava Ultimate and Vita Enamic, which were significantly different from Vita Mark II and Vita Suprinity (p<0.05). For Vita Mark II, Vita Suprinity, Vita Enamic, and Lava Ultimate, the µTBS obtained with RelyX Unicem 2 was not significantly different from that obtained with RelyX ARC or RelyX Ultimate. All groups obtained at least three types of failure. The adhesive strategy with self-adhesive resin cement was comparable to conventional resin cement with total-etch or self-etch adhesive techniques in the bond of novel CAD/CAM materials to dentin.

The effect of milling and postmilling procedures on the surface roughness of CAD/CAM materials.

PURPOSE: The aim of this study was to evaluate the surface roughness and analyze the surface topography of five different CAD/CAM ceramics and one CAD/CAM composite resin for CEREC after milling and postmilling procedures. MATERIALS AND METHODS: Blocks of the ceramics Mark II, IPS Empress CAD, IPS e.max CAD, Suprinity and Enamic, and blocks of the composite resin Lava Ultimate were milled at CEREC MCXL. Ten flat samples of each material were obtained. The surface roughness (Ra) test was performed before and after milling, crystallization, polishing, and glaze when indicated, followed by SEM and AFM analysis. Data were submitted to one-way ANOVA with repeated measures and the Tukey HSD test (α = 0.05). RESULTS: The milling step significantly increased the roughness of all the tested materials (P < .05). Lithium-based ceramics (IPS e.max CAD and Suprinity) were more suitable to roughness than the other tested materials (P < .05). CONCLUSIONS: The polishing methods were able to reduce roughness to baseline values, except for lithium-based ceramics. Glaze reduced significantly the roughness of lithium-based ceramics without a difference from the baseline. SEM and AFM images revealed that glazed surfaces are smoother than polished surfaces. CLINICAL SIGNIFICANCE: All hard-milling CAD/CAM materials, that is, fully sintered, should be only hand polished. The glaze step can be suppressed resulting in time saving. However, the glaze step in soft-milling lithium disilicate is imperative.

Effect of surface treatment of prefabricated teeth on shear bond strength of orthodontic brackets.

OBJECTIVE:: The aim of this in vitro study was to evaluate and compare the effects of grinding, drilling, sandblasting, and ageing prefabricated teeth (PfT) on the shear bond strength (SBS) of orthodontic brackets, as well as the effects of surface treatments on the adhesive remnant index (ARI). METHODS:: One-hundred-ninety-two PfT were divided into four groups (n = 48): Group 1, no surface treatment was done; Group 2, grinding was performed with a cylindrical diamond bur; Group 3, two drillings were done with a spherical diamond bur; Group 4, sandblasting was performed with 50-µm aluminum oxide. Before the experiment, half of the samples stayed immersed in distilled water at 37oC for 90 days. Brackets were bonded with Transbond XT and shear strength tests were carried out using a universal testing machine. SBS were compared by surface treatment and by ageing with two-way ANOVA, followed by Tukey's test. ARI scores were compared between surface treatments with Kruskal-Wallis test followed by Dunn's test. RESULTS:: Surface treatments on PfT enhanced SBS of brackets (p< 0.01), result not observed with ageing (p= 0.45). Groups II, III, and IV showed higher SBS and greater ARI than the Group 1 (p< 0.05). SBS was greater in the groups 3 and 4 (drilling, sandblasting) than in the Group 2 (grinding) (p< 0.05). SBS and ARI showed a positive correlation (Spearman's R2= 0.57; p< 0.05). CONCLUSION:: Surface treatment on PfT enhanced SBS of brackets, however ageing did not show any relevance. Sandblasting and drilling showed greater SBS than grinding. There was a positive correlation between SBS and ARI.

Effect of surface treatment of prefabricated teeth on shear bond strength of orthodontic brackets

ABSTRACT Objective: The aim of this in vitro study was to evaluate and compare the effects of grinding, drilling, sandblasting, and ageing prefabricated teeth (PfT) on the shear bond strength (SBS) of orthodontic brackets, as well as the effects of surface treatments on the adhesive remnant index (ARI). Methods: One-hundred-ninety-two PfT were divided into four groups (n = 48): Group 1, no surface treatment was done; Group 2, grinding was performed with a cylindrical diamond bur; Group 3, two drillings were done with a spherical diamond bur; Group 4, sandblasting was performed with 50-µm aluminum oxide. Before the experiment, half of the samples stayed immersed in distilled water at 37oC for 90 days. Brackets were bonded with Transbond XT and shear strength tests were carried out using a universal testing machine. SBS were compared by surface treatment and by ageing with two-way ANOVA, followed by Tukey's test. ARI scores were compared between surface treatments with Kruskal-Wallis test followed by Dunn's test. Results: Surface treatments on PfT enhanced SBS of brackets (p< 0.01), result not observed with ageing (p= 0.45). Groups II, III, and IV showed higher SBS and greater ARI than the Group 1 (p< 0.05). SBS was greater in the groups 3 and 4 (drilling, sandblasting) than in the Group 2 (grinding) (p< 0.05). SBS and ARI showed a positive correlation (Spearman's R2= 0.57; p< 0.05). Conclusion: Surface treatment on PfT enhanced SBS of brackets, however ageing did not show any relevance. Sandblasting and drilling showed greater SBS than grinding. There was a positive correlation between SBS and ARI.

RESUMO Objetivo: o objetivo desse estudo in vitro foi avaliar e comparar os efeitos de desgastes, perfurações, jateamento e envelhecimento de dentes pré-fabricados (Dpf) na resistência ao cisalhamento (RC) de braquetes ortodônticos, bem como os efeitos dos tratamentos de superfície no índice de adesivo remanescente (ARI). Métodos: 192 Dpf foram divididos em quatro grupos (n = 48): Grupo 1, sem tratamento; Grupo 2, desgaste de sulcos com broca diamantada cilíndrica; Grupo 3, duas perfurações com broca diamantada esférica; e Grupo 4, jateamento com partículas de óxido de alumínio de 50µm. Antes do experimento, metade das amostras ficou imersa em água destilada a 37oC durante 90 dias. Os braquetes foram colados com Transbond XT e os testes de cisalhamento foram realizados com uma máquina universal de ensaios. A RC foi comparada, por tratamento de superfície e por envelhecimento, utilizando-se análise de variância e teste de Tukey. Os escores ARI foram comparados entre os tratamentos de superfície usando o teste Kruskal-Wallis e o teste de Dunn. Resultados: os tratamentos de superfície aumentaram a RC dos braquetes (p < 0,01) e o envelhecimento não aumentou a RC (p = 0,45). Os Grupos 2, 3 e 4 mostraram maior RC e maior ARI do que o Grupo 1 (p < 0,05). A RC foi maior nos Grupos 3 e 4 (perfuração, jateamento) do que no Grupo 2 (desgaste) (p < 0,05). RC e ARI apresentaram correlação positiva (R2 = 0,57; p < 0,05). Conclusão: o tratamento de superfície dos Dpf aumentou a RC dos braquetes; porém, o envelhecimento não foi relevante. O jateamento e a perfuração mostraram maior RC do que o desgaste. Existe uma correlação positiva entre RC e ARI.

The addition of silica nanoparticles on the mechanical properties of dental stone.

STATEMENT OF PROBLEM: The current application of nanotechnology in dentistry is limited to nanoparticles incorporated into adhesive systems and composite resins. Dental stone is a widely used material, and the incorporation of silica nanoparticles is still unexplored. PURPOSE: The purpose of this in vitro study was to evaluate the mechanical properties of dental stone after the addition of silica nanoparticles in different concentrations. MATERIAL AND METHODS: A total of 180 specimens were prepared, 90 for each dental stone (Durone and Fuji Rock). For the control group (CG), no silica particles were added, while test group TGnI had silica nanoparticles added to 1 wt%, and test group TGnV had silica nanoparticles added to 5 wt%. The roughness, diametral tensile strength (DTS), and compressive strength were measured 24 hours after the start of spatulation. RESULTS: The mean roughness values for Durone were 0.55, 0.36, and 0.28 µm for CG, TGnI, and TGnV; for Fuji Rock, the mean roughness values were 0.47 for CG, 0.31 for TGnI, and 0.35 µm for TGnV. The mean DTS values for Durone were 6.0, 5.1, and 5.0 MPa for CG, TGnI, and TGnV, respectively, and for Fuji Rock, the mean DTS values were 6.4, 5.2, and 4.5 MPa for CG, TGnI, and TGnV, respectively. The mean compressive strength values for Durone were 35.4, 32.7, and 32.4 MPa for CG, TGnI, and TGnV, respectively, and for Fuji Rock, the mean compressive strength values were 42.9, 31.2, and 29.8 MPa for CG, TGnI, and TGnV respectively. CONCLUSIONS: Surface roughness was statistically lower for the Durone and Fuji Rock stones (P<.001) when silica nanoparticles were added. The addition of silica nanoparticles did not significantly affect the DTS and compressive strength of Durone compared with CG (P>.05) but did affect the DTS of Fuji Rock when 5 wt% was added and the compressive strength in both concentrations (P<.05).

Microtensile bond strength of CAD/CAM materials to dentin under different adhesive strategies

Abstract: The present study aimed to evaluate the microtensile bond strength (μTBS) of novel computer-aided design/computer-aided manufacturing (CAD/CAM) restorative materials to dentin using different adhesive strategies. Thirty-two crowns were milled using CAD/CAM materials (Vita Mark II as control, Vita Suprinity, Vita Enamic and Lava Ultimate) and luted to dentin using different resin cements (RelyX ARC, RelyX Unicem 2 and RelyX Ultimate). The specimens were stored in 100% relative humidity at 37°C for 24 h and sectioned. The samples (n = 16) with cross-sectional areas of approximately 0.90 mm2, were submitted to a μTBS test in a universal testing machine with a crosshead speed of 0.5 mm/min. The samples were analyzed with SEM to determinate the failure mode. According to 2-way ANOVA and Tukey's test (α=0.05), the interaction effect (material x luting strategy) was significant (p=0.001). Regardless of the luting strategy, a higher μTBS was obtained with Lava Ultimate and Vita Enamic, which were significantly different from Vita Mark II and Vita Suprinity (p<0.05). For Vita Mark II, Vita Suprinity, Vita Enamic, and Lava Ultimate, the μTBS obtained with RelyX Unicem 2 was not significantly different from that obtained with RelyX ARC or RelyX Ultimate. All groups obtained at least three types of failure. The adhesive strategy with self-adhesive resin cement was comparable to conventional resin cement with total-etch or self-etch adhesive techniques in the bond of novel CAD/CAM materials to dentin.

Relined fiberglass post: an ex vivo study of the resin cement thickness and dentin-resin interface.

The aim of this study was to evaluate the thickness of resin cements in the root thirds when using conventional fiberglass posts (CP) and relined fiberglass posts (RP) in weakened roots and to evaluate the morphological characteristics of the dentin-resin interface. Forty human maxillary anterior teeth had the crown sectioned below the cemento-enamel junction. The canals were endodontically treated and weakened with diamond burs. Teeth were divided into four groups (n = 10): Group 1 - CP + RelyX ARC; Group 2 - CP + RelyX U200; Group 3 - RP + RelyX ARC; and Group 4 - RP + RelyX U200. Prior to luting, 0.1% Fluorescein and 0.1% Rhodamine B dyes were added to an adhesive and resin cement, respectively. Slices were obtained from the apical, middle, and cervical thirds of the root. Confocal laser scanning microscopy images were recorded in four areas (buccal, lingual, mesial, distal) of each third. In each area, four equidistant measures of the resin cement were made and the mean value was calculated. The interface morphology was observed. The data were submitted to three-way ANOVA and Tukey's test (α = 0.05). The interaction between fiberglass posts, resin cement, and root thirds was significant (p < 0.0001). The resin cement thicknesses were significantly lower for RP in comparison with CP, except in the apical third. There was no significant difference between the resin cements for RP. There was formation of resin cement tags and adhesive tags along the root for RP. RP favored the formation of thin and uniform resin cement films and resin tags in weakened roots.

Surface roughness and maintenance of surface sealants for resin composites after toothbrushing.

PURPOSES: (1) To evaluate in vitro the surface roughness of a resin composite covered with three surface sealants and submitted to simulated toothbrushing for different periods; (2) Verify, through scanning electron microscopy (SEM), the presence of surface sealants after simulated toothbrushing; and (3) To evaluate whether the type of dentifrice influences the maintenance of the surface sealant. The study hypothesis was that neither variable would influence the surface roughness of the composite and the maintenance of the surface sealant. METHODS: 108 specimens were prepared with the resin Amelogen Plus, and divided into six groups (n = 18) according to the type of surface sealant [Fortify (F), BisCover LV (B) and Permaseal (P)] and toothpaste [Total 12 Clean Mint (CT) and Colgate Total 12 Professional Whitening (PW)]. The samples were subjected to brushing cycles, simulating periods of 6, 12, 18, and 24 months. After each period, the surface roughness of the samples was measured. An additional group of 48 samples was prepared for SEM analysis. The results were analyzed by ANOVA with three fixed variables (sealants, time and toothpaste) and by Tukey's test (α = 0.05). RESULTS: BisCover had the lowest mean surface roughness (0.06 µm) compared with the sealants Fortify (0.09 µm) and Permaseal (0.08 µm), which were not statistically different. Fortify, at 12 months of brushing, had the highest mean roughness (0.13 µm). The mean roughness for the dentifrice CT was lower (0.07 µm) when compared with PW (0.08 µm) and was statistically different. Roughness increased up to 12 months of simulated brushing (0.04 µm, 0.08 µm and 0.11 µm), decreasing from the 18th month (0.08 µm) to the 24th month of brushing (0.07 µm). None of the sealants was observed (with SEM) to be completely removed from the resin at 24 months of brushing.

Impacto da evolução científica no ensino e na prática odontológica brasileira ao longo dos séculos / Impact of scientific development on Brazilian oral health education and practice through the centuries

A história da Odontologia no Brasil iniciou-se de maneira rudimentar com instrumentos primitivos e sem preocupações com higiene. Não havia nenhuma referência à ciência, apenas à prática da profissão. No século XVII, evidencia-se um aumento no número de cáries e maior demanda por serviços odontológicos estéticos. Porém, apenas em 1879 inicia-se o estudo da Odontologia, no Brasil, e outras faculdades começam a se instalar somente a partir do século XX. A comprovação da origem bacteriana da doença cárie e surgimento de mais estudos referentes às doenças bucais ocorreram somente a partir da década de 1940. A fluoretação da água de abastecimento público foi o primeiro procedimento preventivo realizado no Brasil e o primeiro estudo epidemiológico nacional foi realizado em 1986. O Ministério da Saúde declarou que no ano de 2012, a quantidade de atendimentos odontológicos oferecidos pelo Sistema Único de Saúde foi de 150 milhões de consultas no país, além disso, o governo ampliou o sistema para 90% das cidades brasileiras atingindo uma população de 92 milhões de beneficiados e implementou serviços de promoção, prevenção e recuperação da saúde bucal. Apesar desse grande avanço, o controle da doença cárie em todas as faixas etárias ainda está longe de ser alcançado. Fazer com que todos os progressos obtidos até o momento cheguem a todos os cidadãos deve ser a meta deste século. (AU)

The history of dentistry in Brazil initiated in a rudimentary way with primitive tools and no hygiene preoccupations. There was no reference to science, only the practice of the profession. In the seventeenth century there is evidence about the increase of the number of dental caries and demand for aesthetics dental services. However, only in 1879 began the study of Dentistry in Brazil and new faculties were installed on the twentieth century. Evidence of bacterial decay and the emergence of more studies about oral diseases only occurred since the 1940s. Fluoride supplies of public water was the first preventive procedure performed in Brazil and the first national epidemiological study was conducted in 1986. The Ministry of Health stated that in the year 2012, the amount of dental care offered by the National Health System was 150 million consultations in the country, besides the government expanded the system to 90% of Brazilian cities reaching a population of 92 million of beneficiaries and implemented health promotion, prevention and recovery of oral health services. Despite this breakthrough, the control of caries in all age groups is still far from being achieved. Make all the progress made so far reaching all citizens should be the goal of this century. (AU)

Relined fiberglass post: an ex vivo study of the resin cement thickness and dentin-resin interface

Abstract The aim of this study was to evaluate the thickness of resin cements in the root thirds when using conventional fiberglass posts (CP) and relined fiberglass posts (RP) in weakened roots and to evaluate the morphological characteristics of the dentin-resin interface. Forty human maxillary anterior teeth had the crown sectioned below the cemento-enamel junction. The canals were endodontically treated and weakened with diamond burs. Teeth were divided into four groups (n = 10): Group 1 - CP + RelyX ARC; Group 2 - CP + RelyX U200; Group 3 - RP + RelyX ARC; and Group 4 - RP + RelyX U200. Prior to luting, 0.1% Fluorescein and 0.1% Rhodamine B dyes were added to an adhesive and resin cement, respectively. Slices were obtained from the apical, middle, and cervical thirds of the root. Confocal laser scanning microscopy images were recorded in four areas (buccal, lingual, mesial, distal) of each third. In each area, four equidistant measures of the resin cement were made and the mean value was calculated. The interface morphology was observed. The data were submitted to three-way ANOVA and Tukey's test (α = 0.05). The interaction between fiberglass posts, resin cement, and root thirds was significant (p < 0.0001). The resin cement thicknesses were significantly lower for RP in comparison with CP, except in the apical third. There was no significant difference between the resin cements for RP. There was formation of resin cement tags and adhesive tags along the root for RP. RP favored the formation of thin and uniform resin cement films and resin tags in weakened roots.

Strengthening effect of horizontally placed fiberglass posts in endodontically-treated teeth restored with direct resin composite.

PURPOSE: To assess the fracture strength of cavity preparations, directly restored with resin composite, with and without the presence of fiberglass posts with different diameters. METHODS: 84 extracted third molars were embedded in acrylic resin and divided into six groups (n = 14 per group): healthy (H); cavity preparation (P); cavity preparation + endodontic treatment (PE); PE + resin composite (R); PE + R + 2 horizontally transfixed fiberglass posts 1.1 mm in diameter (PERP1); PE + R + 2 fiberglass posts 1.5 mm in diameter (PERP2). The MOD cavity preparations were standardized with their width corresponding to 2/3 of the buccolingual distance and occlusogingival depth of 4 mm, with 2 mm remaining above the cemento-enamel junction. Endodontic treatments were performed in the PE, R, PERP1 and PERP2 groups. The buccal surface received two demarcations to create orifices for placement of the PERP1 and PERP2 posts. Once the fiberglass posts were placed, the teeth were restored with resin composite. In group R, only resin composite was used. After 24 hours, the teeth were subjected to the fracture toughness test on a universal testing machine. A 10 KN load cell and crosshead speed of 1 mm/minute was used until fracture occurred. After testing, the teeth were inspected for the type of fracture classified as: pulpal floor fracture (AP) or cuspal fracture (CP). RESULTS: The data were subjected to ANOVA and Tukey's test (P < 0.05%), demonstrating a statistical difference between groups: H 3830NA; P 778ND; PE 572.93ND; R 1782NC; PERP1 2988NB; PERP2 3100NAB. The fracture pattern was similar between the tested groups, showing 50% of fracture for cusps and pulpal floor.

Fracture resistance of computer-aided design and computer-aided manufacturing ceramic crowns cemented on solid abutments.

BACKGROUND: Because no information was found in the dental literature regarding the fracture resistance of all-ceramic crowns using CEREC (Sirona) computer-aided design and computer-aided manufacturing (CAD-CAM) system on solid abutments, the authors conducted a study. METHODS: Sixty synOcta (Straumann) implant replicas and regular neck solid abutments were embedded in acrylic resin and randomly assigned (n = 20 per group). Three types of ceramics were used: feldspathic, CEREC VITABLOCS Mark II (VITA); leucite, IPS Empress CAD (Ivoclar Vivadent); and lithium disilicate, IPS e.max CAD (Ivoclar Vivadent). The crowns were fabricated by the CEREC CAD-CAM system. After receiving glaze, the crowns were cemented with RelyX U200 (3M ESPE) resin cement under load of 1 kilogram. For each ceramic, one-half of the specimens were subjected to the fracture resistance testing in a universal testing machine with a crosshead speed of 1 millimeter per minute, and the other half were subjected to the fractured resistance testing after 1,000,000 cyclic fatigue loading at 100 newtons. RESULTS: According to a 2-way analysis of variance, the interaction between the material and mechanical cycling was significant (P = .0001). According to a Tukey test (α = .05), the fracture resistance findings with or without cyclic fatigue loading were as follows, respectively: CEREC VITABLOCKS Mark II (405 N/454 N) was statistically lower than IPS Empress CAD (1169 N/1240 N) and IPS e.max CAD (1378 N/1025 N) (P < .05). The IPS Empress CAD and IPS e.max CAD did not differ statistically (P > .05). According to a t test, there was no statistical difference in the fracture resistance with and without cyclic fatigue loading for CEREC VITABLOCS Mark II and IPS Empress CAD (P > .05). For IPS e.max CAD, the fracture resistance without cyclic fatigue loading was statistically superior to that obtained with cyclic fatigue loading (P < .05). CONCLUSIONS: The IPS Empress CAD and IPS e.max CAD showed higher fracture resistance compared with CEREC VITABLOCS Mark II. The cyclic fatigue loading negatively influenced only IPS e.max CAD. PRACTICAL IMPLICATIONS: The CEREC VITABLOCS Mark II, IPS Empress CAD, and IPS e.max CAD ceramic crowns cemented on solid abutments showed sufficient resistance to withstand normal chewing forces.

The influence of postpouring time on the roughness, compressive strength, and diametric tensile strength of dental stone.

STATEMENT OF PROBLEM: The optimum time after pouring a dental impression before removing the dental cast is unknown with regard to the strength and roughness of the stone. Setting times and the commercial products used are important variables. PURPOSE: The purpose of this study was to evaluate the effect of postpouring time on the surface roughness, compressive strength, and diametric tensile strength of Type IV dental stone. MATERIAL AND METHODS: A total of 270 specimens were prepared from 3 commercial brands of dental stone (Durone, Fuji Rock, and Tuff Rock). Surface roughness, compressive strength, and diametric tensile strength were assessed at 1 hour, 24 hours, and 7 days after pouring. Specimens 6 mm in diameter and 3 mm in height were produced for roughness and diametric tensile strength tests. Specimens 3 mm in diameter and 6 mm in height were used to measure compressive strength. The results were analyzed with the general linear model and Tukey honestly significant difference test (α=.05). RESULTS: The surface roughness measured for the different types of dental stone tested varied from 0.3 µm (Durone, 1 hour) to 0.64 µm (Tuff Rock, 7 days). The diametric tensile strength ranged from 3.94 MPa (Tuff Rock, 1 hour) to 9.20 MPa (Durone, 7 days). The compressive strength varied from 26.67 MPa (Durone, 1 hour) to 65.14 MPa (Fuji Rock, 7 days). CONCLUSIONS: Surface roughness (P=.005), diametric tensile strength (P=.001), and compressive strength (P=.001) increased significantly with time after pouring. The commercial brand used affected roughness (P=.001), diametric tensile strength (P=.004), and compressive strength (P=.001). Tuff Rock exhibited the highest surface roughness. The highest diametric tensile strength values were recorded for Durone and Fuji Rock. Fuji Rock exhibited the highest compressive strength.

Does immediate dentin sealing influence the polymerization of impression materials?

OBJECTIVES: The objective of the following study is to evaluate the interaction between the resin materials used in immediate dentin sealing (IDS) techniques and impression materials with two different techniques to eliminate the oxygen-inhibition layer. MATERIALS AND METHODS: The occlusal dentin surface of 35 human molars was exposed. The teeth were used in two Groups: Group 1 - Impression with Express XT; Group 2 - Impression with Impregum. Groups 1 and 2 were divided into 14 subgroups: Groups 1a and 2a - Control groups; 1b and 2b - IDS with Clearfil SE Bond (CSE); 1c and 2c - IDS with CSE + additional polymerization with glycerin jelly; 1d and 2d - IDS with CSE + alcohol; 1e and 2e - IDS with CSE and Protect Liner F (PLF); 1f and 2f - IDS with CSE and PLF + additional polymerization with glycerin jelly; and 1g and 2g - IDS with CSE and PLF + alcohol. Five teeth were used in each experimental group, and the tooth surface was photographed using a digital camera. RESULTS: Small quantity of unpolymerized impression material remained attached to the CSE or to the PLF in Groups 1b and 1e. Groups 1c and 1d prevented the interaction. Small quantity of polymerized impression material remained attached to the CSE or to the PLF for Groups 2b and 2e. The same interaction was observed for Groups 2c and 2d. For Groups 2c and 2f, no interactions were observed. CONCLUSION: Resin materials interacted with impression materials. The application of glycerin jelly and alcohol prevented the interaction of CSE with Express XT and PLF with Impregum; however, these treatments were not completely effective in preventing the interaction of CSE with Impregum and PLF with Express XT.

Effect of resin cements and aging on cuspal deflection and fracture resistance of teeth restored with composite resin inlays.

PURPOSE: To evaluate the influence of resin cements and aging on cuspal deflection, fracture resistance, and mode of failure of endodontically treated teeth restored with composite resin inlays. MATERIALS AND METHODS: Seventy-two maxillary premolars were divided into 6 groups: 1: sound teeth as control (C); 2: preparations without restoration (WR); 3: inlays luted with RelyX ARC (ARC); 4: inlays luted with RelyX Unicem (RLXU); 5: inlays luted with Maxcem Elite (MCE); 6: inlays luted with SeT (ST). Groups 2 to 6 received mesio-occlusal-distal preparations and endodontic treatment. Stone casts were made for groups 3 to 6. Composite resin inlays were built over each cast and luted with the resin cements. A 200-N load was applied on the occlusal aspect and the cuspal deflection was measured using a micrometer before and after 500,000 cycles of fatigue loading (200 N; 500,000 cycles). The specimens were then submitted to an axial load until failure. RESULTS: The median cuspal deflection (µm) and median fracture resistance (N) were calculated and statistically analyzed using Kruskal-Wallis and Mann-Whitney tests (p < 0.01). Values followed by the same letter represent no statistically significant difference. Cuspal deflection before cyclic loading: C = 3 µma; ARC = 4 µmab; RLXU= 5 µmab; MCE = 21 µmb; ST = 51 µmbc; WR = 69 µmc. Cuspal deflection after cyclic loading: ARC = 6 µma; RLXU = 19 µmab; MCE = 33 µmb; ST = 62 µmb. Fracture resistance in N: C = 1902a; ARC = 980b; RLXU = 670c; MCE = 533c; ST = 601c; WR = 526c. According to the Wilcoxon test, there was no statistical difference between the cuspal deflection before and after cyclic loading only for ARC (p = 0.015). There was a predominance of recovery fractures for the restored groups. CONCLUSION: Composite resin inlays luted with RelyX ARC maintained cuspal deflection stability and showed higher fracture resistance of the teeth than did inlays luted with the other cements tested.

Influence of restorative techniques on fracture load of endodontically treated premolars.

UNLABELLED: OBJECTIVE. This study evaluated the influence of restorative techniques on the fracture load and fracture mode of endodontically treated premolars with MOD cavities. MATERIALS AND METHODS: Sixty maxillary premolars were divided into groups: G1 - sound teeth; G2 - direct technique using Four Season; G3 - Adoro inlays; G4 - Adoro onlays; G5 - Empress inlays; G6 - Empress onlays. The specimens were submitted to compressive axial loading until failure. The fracture mode was analyzed. RESULTS. According to ANOVA and Tukey's test (α=0.05), the sound teeth (1370.61 N) showed the highest fracture load mean, which did not differ statistically from IPS Empress onlays (1304.21 N). Intermediate values were obtained for IPS Empress inlays (918.76 N), Adoro onlays (861.15 N), Adoro inlays (792.71 N) which did not differ statistically among them. The lowest fracture load was obtained for direct restorations with Four Seasons (696.08 N), which did not differ statistically from the Adoro inlays. CONCLUSIONS. The ceramic restorations provided higher fracture load and more incidences of catastrophic fractures. Cuspal coverage increased teeth fracture load. The results were similar for direct and indirect inlays with composite resin.

Assessment of the mechanical properties of glass ionomer cements for orthodontic cementation

OBJECTIVE: To evaluate the mechanical properties of three glass ionomers cements (GICs) used for band cementation in Orthodontics. METHODS: Two conventional glass ionomers (Ketac Cem Easy mix/3M-ESPE and Meron/Voco) and one resin modified glass ionomer (Multi-cure Glass ionomer/3M-Unitek) were selected. For the compressive strength and diametral tensile strength tests, 12 specimens were made of each material. For the microhardness test 15 specimens were made of each material and for the shear bond strength tests 45 bovine permanent incisors were used mounted in a self-cure acrylic resin. Then, band segments with a welded bracket were cemented on the buccal surface of the crowns. For the mechanical tests of compressive and diametral tensile strength and shear bond strength a universal testing machine was used with a crosshead speed of 1,0 mm/min and for the Vickers microhardness analysis tests a Microdurometer was used with 200 g of load during 15 seconds. The results were submitted to statistical analysis through ANOVA complemented by Tukey's test at a significance level of 5%. RESULTS: The results shown that the Multi-Cure Glass Ionomer presented higher diametral tensile strength (p < 0.01) and compressive strength greater than conventional GICs (p = 0.08). Moreover, Ketac Cem showed significant less microhardness (p < 0.01). CONCLUSION: The resin-modified glass ionomer cement showed high mechanical properties, compared to the conventional glass ionomer cements, which had few differences between them.

OBJETIVO: avaliar as propriedades mecânicas de três cimentos de ionômero de vidro (CIVs) utilizados para cimentação de anéis ortodônticos. MÉTODOS: foram utilizados dois CIVs convencionais (Ketac Cem Easy mix/3M-ESPE e Meron/Voco) e um CIV modificado por resina (Multi-Cure Glass ionomer/3M-Unitek). Para os testes de resistência à compressão e tração diametral, foram confeccionados 12 corpos de prova de cada material. Para os testes de microdureza, foram confeccionados 15 corpos de prova de cada material; para os testes de resistência de união ao cisalhamento, foram utilizados 45 dentes bovinos incluídos em resina acrílica, sobre os quais foi cimentada uma lâmina de anel ortodôntico com braquete soldado a ela para a realização dos ensaios. Para os testes de compressão, tração diametral e cisalhamento, foi utilizada uma máquina universal de ensaios a uma velocidade de 1mm/min; para os testes de microdureza Vickers, foi utilizado um microdurômetro com 200g de carga durante 15 segundos. Os resultados foram submetidos à análise estatística ANOVA, complementada pelo teste de Tukey ao nível de significância de 5%. RESULTADOS: os resultados demonstraram que o Multi-Cure Glass Ionomer apresentou resistência à tração diametral significativamente maior (p < 0,01) e maior resistência à compressão (p = 0,08) em relação aos CIVs convencionais. Além disso, o Ketac Cem apresentou microdureza significativamente maior que os demais materiais (p < 0,01). CONCLUSÃO: o CIV modificado por resina apresentou propriedades mecânicas superiores às dos CIVs convencionais, que, por sua vez, apresentaram poucas diferenças entre si.