Ultrafast Nanodrum-on-Chip Pixels.

Environmentally friendly, ultrafast display pixels of micrometer sizes are fabricated with nanometer-thick gold films and Si/SiO2 wafers. The color displayed is due to both the plasmon response of the gold film and the optical interference from the Fabry-Peerot cavity formed by the underlying silicon substrate, the semitransparent gold film and the air gap between them. When an electric potential is applied to the gold film, the electrostatic force induces an attraction between the gold film and the silicon wafer. Due to the flexibility of the film, the size of the air gap changes, resulting in a changing color. By applying different driving signals, we have achieved cyan, magenta, and yellow reflected colors. The maximum switching rate of the pixel is primarily determined by the thickness dependence of the metal drum and its Young's modulus and is typically in the MHz regime.

The Multiple Roles of Na Ions in Highly Efficient CZTSSe Solar Cells.

Sodium (Na) doping is a well-established technique employed in chalcopyrite and kesterite solar cells. While various improvements can be achieved in crystalline quality, electrical properties, or defect passivation of the absorber materials by incorporating Na, a comprehensive demonstration of the desired Na distribution in CZTSSe is still lacking. Herein, a straightforward Na doping approach by dissolving NaCl into the CZTS precursor solution is proposed. It is demonstrated that a favorable Na ion distribution should comprise a precisely controlled Na+ concentration at the front surface and an enhanced distribution within the bottom region of the absorber layer. These findings demonstrated that Na ions play several positive roles within the device, leading to an overall power conversion efficiency of 12.51%.

Electrophoretic Deposition of Single Nanoparticles.

The controlled assembly of colloid particles on a solid substrate has always been a major challenge in colloid and surface science. Here we provide an overview of electrophoretic deposition (EPD) of single charge-stabilized nanoparticles. We demonstrate that surface templated EPD (STEPD) assembly, which combines EPD with top-down nanofabrication, allows a wide range of nanoparticles to be built up into arbitrary structures with high speed, scalability, and excellent fidelity. We will also discuss some of the current colloid chemical limitations and challenges in STEPD assembly for sub-10 nm nanoparticles and for the fabrication of densely packed single particle arrays.

An ITO-Free Kesterite Solar Cell.

Photovoltaic thin film solar cells based on kesterite Cu2 ZnSn(S, Se)4 (CZTSSe) have reached 13.8% sunlight-to-electricity conversion efficiency. However, this efficiency is still far from the Shockley-Queisser radiative limit and is hindered by the significant deficit in open circuit voltage (VOC ). The presence of high-density interface states between the absorber layer and buffer or window layer leads to the recombination of photogenerated carriers, thereby reducing effective carrier collection. To tackle this issue, a new window structure ZnO/AgNW/ZnO/AgNW (ZAZA) comprising layers of ZnO and silver nanowires (AgNWs) is proposed. This structure offers a simple and low-damage processing method, resulting in improved optoelectronic properties and junction quality. The ZAZA-based devices exhibit enhanced VOC due to the higher built-in voltage (Vbi ) and reduced interface recombination compared to the usual indium tin oxide (ITO) based structures. Additionally, improved carrier collection is demonstrated as a result of the shortened collection paths and the more uniform carrier lifetime distribution. These advances enable the fabrication of the first ITO-free CZTSSe solar cells with over 10% efficiency without an anti-reflective coating.

Energy dissipation during homogeneous wetting of surfaces with randomly and periodically distributed cylindrical pillars.

HYPOTHESIS: Understanding contact angle hysteresis on rough surfaces is important as most industrially relevant and naturally occurring surfaces possess some form of random or structured roughness. We hypothesise that hysteresis can be described by the dilute defect model of Joanny & de Gennes [1] and that the energy dissipation occurring during the stick-slip motion of the contact line is key to developing a predictive equation for hysteresis. EXPERIMENTS: We measured hysteresis on surfaces with randomly distributed and periodically arranged microscopic cylindrical pillars for a variety of different liquids in air. The inherent (flat surface) contact angles tested range from lyophilic (θe=33.8°) to lyophobic (θe=112.0°). FINDINGS: A methodology for averaging the measured advancing and receding contact angles on random surfaces is presented. Based on these results correlations for roughness-induced energy dissipation are derived, and an equation for predicting the advancing and receding contact angles during homogeneous (Wenzel) wetting on random surfaces is presented. Equations that predict the onset of the alternate wetting conditions of hemiwicking, split-advancing, split-receding and heterogeneous (Cassie) wetting are also derived, thus defining the range of validity for the homogeneous wetting equation. A 'cluster' concept is proposed to explain the measurably higher hysteresis exhibited by structured surfaces compared to random surfaces.

A reflective display based on the electro-microfluidic assembly of particles within suppressed water-in-oil droplet array.

Reflective displays have stimulated considerable interest because of their friendly readability and low energy consumption. Herein, we develop a reflective display technique via an electro-microfluidic assembly of particles (eMAP) strategy whereby colored particles assemble into annular and planar structures inside a dyed water droplet to create "open" and "closed" states of a display pixel. Water-in-oil droplets are compressed within microwells to form a pixel array. The particles dispersed in droplets are driven by deformation-strengthened dielectrophoretic force to achieve fast and reversible motion and assemble into multiple structures. This eMAP based device can display designed information in three primary colors with ≥170° viewing angle, ~0.14 s switching time, and bistability with an optimized material system. This proposed technique demonstrates the basis of a high-performance and energy-saving reflective display, and the display speed and color quality could be further improved by structure and material optimization; exhibiting a potential reflective display technology.

Temperature Dependence of the CdS Bandgap in the Extreme Confinement Regime.

A non-empirical equation describing the effect of size on the temperature dependence of the optical bandgap of CdS (dEg/dT) is obtained on the basis of the Brus equation. Intriguingly, we find that dEg/dT diverges strongly from bulk values only within the "extreme confinement" (EC) regime. We conducted both experimental and theoretical investigations of the absorption spectra of CdS clusters and quantum dots as a function of temperature above room temperature. Our results show that the value of dEg/dT obtained from absorption spectra in the EC regime is 2.5 times higher than in the strong confinement regime. Notable ligand sensitivities are also observed for dEg/dT in the case of CdS clusters. Ab initio molecular dynamics simulations and density functional theory calculations reveal that thermal fluctuations are the crucial factor influencing the bandgap temperature coefficient. Our results help resolve some long-standing debates regarding the dEg/dT behavior of semiconductor quantum dots.

Gold Nanodrum Resonators.

Nanodrum resonators have been fabricated using nanometer-thick gold films as the drumheads. The fabrication method is favorable for large-area array manufacture of arbitrary shapes. The drum resonators exhibit fundamental mode vibration frequencies in the MHz regime. We use the stretched-plate model to describe the natural vibrations of the drum. The Q factor of the fundamental mode increases as the thickness of the drum increases and decreases as the drum diameter goes up. The highest Q factor of the fundamental mode reaches 290 at room temperature and atmospheric pressure. Based on the deduced material properties we estimate that the resonator has a mass sensitivity of 1.11 × 10-22 g/Hz.

Tuning the Photoluminescence Anisotropy of Semiconductor Nanocrystals.

Semiconductor nanocrystals are promising optoelectronic materials. Understanding their anisotropic photoluminescence is fundamental for developing quantum-dot-based devices such as light-emitting diodes, solar cells, and polarized single-photon sources. In this study, we experimentally and theoretically investigate the photoluminescence anisotropy of CdSe semiconductor nanocrystals with various shapes, including plates, rods, and spheres, with either wurtzite or zincblende structures. We use defocused wide-field microscopy to visualize the emission dipole orientation and find that spheres, rods, and plates exhibit the optical properties of 2D, 1D, and 2D emission dipoles, respectively. We rationalize the seemingly counterintuitive observation that despite having similar aspect ratios (width/length), rods and long nanoplatelets exhibit different defocused emission patterns by considering valence band structures calculated using multiband effective mass theory and the dielectric effect. The principles are extended to provide general relationships that can be used to tune the emission dipole orientation for different materials, crystalline structures, and shapes.

Room Temperature Bias-Selectable, Dual-Band Infrared Detectors Based on Lead Sulfide Colloidal Quantum Dots and Black Phosphorus.

A single photodetector capable of switching its peak spectral photoresponse between two wavelength bands is highly useful, particularly for the infrared (IR) bands in applications such as remote sensing, object identification, and chemical sensing. Technologies exist for achieving dual-band IR detection with bulk III-V and II-VI materials, but the high cost and complexity as well as the necessity for active cooling associated with some of these technologies preclude their widespread adoption. In this study, we leverage the advantages of low-dimensional materials to demonstrate a bias-selectable dual-band IR detector that operates at room temperature by using lead sulfide colloidal quantum dots and black phosphorus nanosheets. By switching between zero and forward bias, these detectors switch peak photosensitive ranges between the mid- and short-wave IR bands with room temperature detectivities of 5 × 109 and 1.6 × 1011 cm Hz1/2 W-1, respectively. To the best of our knowledge, these are the highest reported room temperature values for low-dimensional material dual-band IR detectors to date. Unlike conventional bias-selectable detectors, which utilize a set of back-to-back photodiodes, we demonstrate that under zero/forward bias conditions the device's operation mode instead changes between a photodiode and a phototransistor, allowing additional functionalities that the conventional structure cannot provide.

Polarity-Tunable Field Effect Phototransistors.

Field-effect phototransistors feature gate voltage modulation, allowing dynamic performance control and significant signal amplification. A field-effect phototransistor can be designed to be inherently either unipolar or ambipolar in its response. However, conventionally, once a field-effect phototransistor has been fabricated, its polarity cannot be changed. Herein, a polarity-tunable field-effect phototransistor based on a graphene/ultrathin Al2O3/Si structure is demonstrated. Light can modulate the gating effect of the device and change the transfer characteristic curve from unipolar to ambipolar. This photoswitching in turn produces a significantly improved photocurrent signal. The introduction of an ultrathin Al2O3 interlayer also enables the phototransistor to achieve a responsivity in excess of 105 A/W, a 3 dB bandwidth of 100 kHz, a gain-bandwidth product of 9.14 × 1010 s-1, and a specific detectivity of 1.91 × 1013 Jones. This device architecture enables the gain-bandwidth trade-off in current field-effect phototransistors to be overcome, demonstrating the feasibility of simultaneous high-gain and fast-response photodetection.

Ligand and solvent effects on the absorption spectra of CdS magic-sized clusters.

The absorption spectra of congenetic wurtzite (WZ) and zincblende (ZB) CdS magic-sized clusters are investigated. We demonstrate that the exciton peak positions can be tuned by up to 500 meV by varying the strong coupling between X-type ligands and the semiconductor cores, while the addition of L-type ligands primarily affects cluster midgap states. When Z-type ligands are displaced by L-type ligands, red shifts in the absorption spectra are observed, despite the fact there is a small decrease in cluster size. Density functional theory calculations are used to explain these findings and they reveal the importance of Cd and S dangling bonds on the midgap states during the Z- to L-type ligand exchange process. Overall, ZB CdS clusters show higher chemical stability than WZ clusters but their optical properties exhibit greater sensitivity to the solvent. Conversely, WZ CdS clusters are not stable in a Lewis base-rich environment, resulting in various changes in their spectra. Our findings enable researchers to select capping ligands that modulate the optical properties of semiconductor clusters while maintaining precise control over their solvent interactions.

Synthesis of Size-Tunable Indium Nitride Nanocrystals.

Indium nitride (InN) is an air stable III-V semiconductor with a small band gap of 0.7 eV and as such is of interest as a key material in near-infrared (NIR) LEDs, photodetectors, and multijunction solar cells. Conventionally, InN has been synthesized through physical deposition techniques which involve extreme temperatures and harsh conditions and yield nonluminescent materials. Here we report a new low temperature, solution-based synthetic route to colloidal InN nanocrystals that produces phase-pure wurtzite InN with tunable photoluminescence. The luminescence is attributed to the presence of InN surface states.

Spectroelectrochemistry of CdSe/CdxZn1-xS Nanoplatelets.

We report an unexpected enhancement of photoluminescence (PL) in CdSe-based core/shell nanoplatelets (NPLs) upon electrochemical hole injection. Moderate hole doping densities induce an enhancement of more than 50% in PL intensity. This is accompanied by a narrowing and blue-shift of the PL spectrum. Simultaneous, time-resolved PL experiments reveal a slower luminescence decay. Such hole-induced PL brightening in NPLs is in stark contrast to the usual observation of PL quenching of CdSe-based quantum dots following hole injection. We propose that hole injection removes surface traps responsible for the formation of negative trions, thereby blocking nonradiative Auger processes. Continuous photoexcitation causes the enhanced PL intensity to decrease back to its initial level, indicating that photocharging is a key step leading to loss of PL luminescence during normal aging. Modulating the potential can be used to reversibly enhance or quench the PL, which enables electro-optical switching.

Evaluation of a lanthanide nanoparticle-based contrast agent for microcomputed tomography of porous channels in subchondral bone.

Osteoarthritis (OA) is a chronic joint disease that causes disability and pain. The osteochondral interface is a gradient tissue region that plays a significant role in maintaining joint health. It has been shown that during OA, increased neoangiogenesis creates porous channels at the osteochondral interface allowing the transport of molecules related to OA. Importantly, the connection between these porous channels and the early stages of OA development is still not fully understood. Microcomputed tomography (microCT) offers the ability to image the porous channels at the osteochondral interface, however, a contrast agent is necessary to delineate the different X-ray attenuations of the tissues. In this study BaYbF5 -SiO2 nanoparticles are synthesized and optimized as a microCT contrast agent to obtain an appropriate contrast attenuation for subsequent segmentation of structures of interest, that is, porous channels, and mouse subchondral bone. For this purpose, BaYbF5 nanoparticles were synthesized and coated with a biocompatible silica shell (SiO2 ). The optimized BaYbF5 -SiO2 27 nm nanoparticles exhibited the highest average microCT attenuation among the biocompatible nanoparticles tested. The BaYbF5 -SiO2 27 nm nanoparticles increased the mean X-ray attenuation of structures of interest, for example, porous channel models and mouse subchondral bone. The BaYbF5 -SiO2 contrast attenuation was steady after diffusion into mouse subchondral bone. In this study, we obtained for the first time, the average microCT attenuation of the BaYbF5 -SiO2 nanoparticles into porous channel models and mouse subchondral bone. In conclusion, BaYbF5 -SiO2 nanoparticles are a potential contrast agent for imaging porous channels at the osteochondral interface using microCT.

Electro-Microfluidic Assembly Platform for Manipulating Colloidal Structures inside Water-in-Oil Emulsion Droplets.

Colloidal assembly is a key strategy in nature and artificial device. Hereby, an electromicrofluidic assembly platform (eMAP) is proposed and validated to achieve 3D colloidal assembly and manipulation within water droplets. The water-in-oil emulsion droplets autoposition in the eMAP driven by dielectrophoresis, where the (di)electrowetting effect induces droplet deformation, facilitating quadratic growth of the electric field in water droplet to achieve "far-field" dielectrophoretic colloidal assembly. Reconfigurable 3D colloidal configurations are observed and dynamically programmed via applied electric fields, colloidal properties, and droplet size. Binary and ternary colloidal assemblies in one droplet allow designable chemical and physical anisotropies for functional materials and devices. Integration of eMAP in high throughput enables mass production of functional microcapsules, and programmable optoelectronic units for display devices. This eMAP is a valuable reference for expanding fundamental and practical exploration of colloidal systems.

Memory in quantum dot blinking.

The photoluminescence intermittency (blinking) of quantum dots is interesting because it is an easily measured quantum process whose transition statistics cannot be explained by Fermi's golden rule. Commonly, the transition statistics are power-law distributed, implying that quantum dots possess at least trivial memories. By investigating the temporal correlations in the blinking data, we demonstrate with high statistical confidence that there is nontrivial memory between the on and off brightness duration data of blinking quantum dots. We define nontrivial memory to be statistical complexity greater than one. We show that this memory cannot be discovered using the transition distribution. We show by simulation that this memory does not arise from standard data manipulations. Finally, we conclude that at least three physical mechanisms can explain the measured nontrivial memory: (1) storage of state information in the chemical structure of a quantum dot; (2) the existence of more than two intensity levels in a quantum dot; and (3) the overlap in the intensity distributions of the quantum dot states, which arises from fundamental photon statistics.