Green ammonia synthesis using CeO2/RuO2 nanolayers on vertical graphene catalyst via electrochemical route in alkaline electrolyte.

The electrochemical synthesis of ammonia at ambient temperature and pressure has the potential to replace the conventional process for the production of ammonia. However, the low ammonia yield and poor long-term stability of catalysts for the synthesis of ammonia hinders the application of this technology. Herein, we endeavored to tackle this challenge by synthesizing 3-D vertical graphene (VG) on Ni foam via a one-step, low-temperature plasma process, which offered high conductivity and large surface area. Subsequently, the vertical graphene on Ni foam was loaded with nanolayers of ruthenium oxide (RuO2, ∼2 nm) and cerium oxide (CeO2, <20 nm) nanoparticles via magnetron sputtering. The incorporation of nanoparticle layers (RuO2 and CeO2/RuO2) on VG significantly increased the NH3 yield in KOH electrolyte. Finally, the performance and long-term stability of this composite material were successfully demonstrated by the addition of CeO2/RuO2 nanolayers on the VG electrocatalyst. The catalyst achieved an excellent performance with a high ammonia synthesis yield of 50.56 µg mgtotal cat.-1 h-1 (1.11 × 10-10 mol cm-2 s-1) during the performance evaluation period of 36 h. This observation was also verified by density functional theory calculation, where CeO2 exhibited the best catalytic performance compared to RuO2 and pristine graphene.

Electrolyte/Structure-Dependent Cocktail Mediation Enabling High-Rate/Low-Plateau Metal Sulfide Anodes for Sodium Storage.

As promising anodes for sodium-ion batteries, metal sulfides ubiquitously suffer from low-rate and high-plateau issues, greatly hindering their application in full-cells. Herein, exemplifying carbon nanotubes (CNTs)-stringed metal sulfides superstructure (CSC) assembled by nano-dispersed SnS2 and CoS2 phases, cocktail mediation effect similar to that of high-entropy materials is initially studied in ether-based electrolyte to solve the challenges. The high nano-dispersity of metal sulfides in CSC anode underlies the cocktail-like mediation effect, enabling the circumvention of intrinsic drawbacks of different metal sulfides. By utilizing ether-based electrolyte, the reversibility of metal sulfides is greatly improved, sustaining a long-life effectivity of cocktail-like mediation. As such, CSC effectively overcomes low-rate flaw of SnS2 and high-plateau demerit of CoS2, simultaneously realizes a high rate and a low plateau. In half-cells, CSC delivers an ultrahigh-rate capability of 327.6 mAh g-1anode at 20 A g-1, far outperforming those of monometallic sulfides (SnS2, CoS2) and their mixtures. Compared with CoS2 phase and SnS2/CoS2 mixture, CSC shows remarkably lowered average charge voltage up to ca. 0.62 V. As-assembled CSC//Na1.5VPO4.8F0.7 full-cell shows a good rate capability (0.05 ~ 1.0 A g-1, 120.3 mAh g-1electrode at 0.05 A g-1) and a high average discharge voltage up to 2.57 V, comparable to full-cells with alloy-type anodes. Kinetics analysis verifies that the cocktail-like mediation effect largely boosts the charge transfer and ionic diffusion in CSC, compared with single phase and mixed phases. Further mechanism study reveals that alternative and complementary electrochemical processes between nano-dispersed SnS2 and CoS2 phases are responsible for the lowered charge voltage of CSC. This electrolyte/structure-dependent cocktail-like mediation effect effectively enhances the practicability of metal sulfide anodes, which will boost the development of high-rate/-voltage sodium-ion full batteries.

Immobilization and stabilization of alcohol dehydrogenase on polyvinyl alcohol fibre.

A polyvinyl alcohol (PVA) fibrous carrier has been chemically modified for the immobilization of yeast alcohol dehydrogenase (ADH) with an aim to increase its stability over a wide pH range, prolong its activity upon storage, and enhance its reusability. The strategy for immobilization involved functionalization of the fibrous carrier with chloropropinoyl chloride followed by amination with ethylenediamine. Tethering of the ADH enzyme to the PVA scaffold was achieved with glutaraldehyde. The activity profile of the immobilized enzyme was compared to soluble enzyme as a function of pH, temperature and reusability. The immobilization of ADH on PVA fibrous carrier shifted the optimal reaction pH from 7 to 9, and improved the thermostability at 60 °C. Furthermore, the immobilized enzyme retained 60% of its original activity after eight cycles of reuse. These results demonstrate that PVA based textiles can serve as a flexible, reusable carrier for enzyme immobilization.

Detection of vapor-phase organophosphate threats using wearable conformable integrated epidermal and textile wireless biosensor systems.

Flexible epidermal tattoo and textile-based electrochemical biosensors have been developed for vapor-phase detection of organophosphorus (OP) nerve agents. These new wearable sensors, based on stretchable organophosphorus hydrolase (OPH) enzyme electrodes, are coupled with a fully integrated conformal flexible electronic interface that offers rapid and selective square-wave voltammetric detection of OP vapor threats and wireless data transmission to a mobile device. The epidermal tattoo and textile sensors display a good reproducibility (with RSD of 2.5% and 4.2%, respectively), along with good discrimination against potential interferences and linearity over the 90-300mg/L range, with a sensitivity of 10.7µA∙cm3∙mg-1 (R2 = 0.983) and detection limit of 12mg/L in terms of OP air density. Stress-enduring inks, used for printing the electrode transducers, ensure resilience against mechanical deformations associated with textile and skin-based on-body sensing operations. Theoretical simulations are used to estimate the OP air density over the sensor surface. These fully integrated wearable wireless tattoo and textile-based nerve-agent vapor biosensor systems offer considerable promise for rapid warning regarding personal exposure to OP nerve-agent vapors in variety of decentralized security applications.

Silk provides a new avenue for third generation biosensors: Sensitive, selective and stable electrochemical detection of nitric oxide.

Using heme entrapped in recombinant silk films, we have produced 3rd generation biosensors, which allow direct electron transfer from the heme center to an electrode avoiding the need for electron mediators. Here, we demonstrate the use of these heme-silk films for the detection of nitric oxide (NO) at nanomolar levels in the presence and absence of oxygen. The sensor was prepared by drop-casting a silk solution on a glassy carbon electrode modified with multiwalled carbon nanotubes (MWCNT) followed by infusion with heme. The sensor was characterized by cyclic voltammetry and showed well defined and reversible Fe+/ Fe3+ redox couple activity, with NO detection by oxidation at potentials above +0.45V or reduction at potentials below - 0.7V. Evaluation of the effect of pH on the sensor response to NO reduction indicated a maximum response at pH 3. The sensor showed good linearity in the concentration range from 19 to 190nM (R2 = 0.99) with a detection limit of 2nM. The sensor had excellent selectivity towards NO with no or negligible interference from oxygen, nitrite, nitrate, dopamine and ascorbic acid and retained 86% of response after 2 months of operation and storage at room temperature.

Design of silk proteins with increased heme binding capacity and fabrication of silk-heme materials.

In our previous studies, heme was bound into honeybee silk to generate materials that could function as nitric oxide sensors or as recoverable heterogeneous biocatalysts. In this study, we sought to increase the heme-binding capacity of the silk protein by firstly redesigning the heme binding site to contain histidine as the coordinating residue and secondly, by adding multiple histidine residues within the core of the coiled coil core region of the modified silk protein. We used detergent and a protein denaturant to confirm the importance of the helical structure of the silk for heme coordination. Aqueous methanol treatment, which was used to stabilize the materials, transformed the low-spin, six-coordinate heme to a five-coordinate high-spin complex, thus providing a vacant site for ligand binding. The optimal aqueous methanol treatment time that simultaneously maintains the helical protein structure and stabilizes the silk material without substantial leaching of heme from the system was determined.

Wearable Flexible and Stretchable Glove Biosensor for On-Site Detection of Organophosphorus Chemical Threats.

A flexible glove-based electrochemical biosensor with highly stretchable printed electrode system has been developed as a wearable point-of-use screening tool for defense and food security applications. This disposable-mechanically robust "lab-on-a-glove" integrates a stretchable printable enzyme-based biosensing system and active surface for swipe sampling on different fingers, and is coupled with a compact electronic interface for electrochemical detection and real-time wireless data transmission to a smartphone device. Stress-enduring inks are used to print the electrode system and the long serpentine connections to the wireless electronic interface. Dynamic mechanical deformation, bending, and stretching studies illustrate the resilience and compliance of the printed traces against extreme mechanical deformations expected for such on-glove sampling/sensing operation. An organophosphorus hydrolase (OPH)-based biosensor system on the index finger enables rapid on-site detection of organophosphate (OP) nerve-agent compounds on suspicious surfaces and agricultural products following their swipe collection on the thumb finger. The new wireless glove-based biosensor system offers considerable promise for field screening of OP nerve-agents and pesticides in defense and food-safety applications, with significant speed and cost advantages. Such "lab-on-a-glove" demonstration opens the area of flexible wearable sensors to future on-the-hand multiplexed chemical detection in diverse fields.

Surface activation of CNT Webs towards layer by layer assembly of biosensors.

Several surface activation methods such as chemical, electrochemical and plasma have been used for enhancing the electrochemical performance of carbon based electrodes for various applications. However, some of these surface activation methods may not be useful depending on the chemical and physical properties of the activated surface. Herein we investigate the surface activation of carbon nanotube (CNT) webs by electrochemical and plasma techniques to enhance their electrochemical performance and enable the fabrication of a biosensor using the layer-by-layer (LBL) approach. The pretreated CNT webs were characterized by SEM, TEM, Raman, XPS and electrochemical methods. TEM images and Raman analysis showed an increase in the level of surface defects upon pretreatment with higher number of defects after electrochemical pretreatment. XPS analysis showed an increase in the level of oxygen functional groups after pretreatment (4 to 5 times increase) which resulted in enhanced water wettability especially for plasma pretreated CNT webs. The pretreated CNT web electrodes also showed an enhanced electrochemical activity towards the oxidation and reduction of different redox probes with higher sensitivity for the electrochemically pretreated CNT web electrode that was accompanied by a higher level of noise in amperometric measurements. A highly linear response was obtained for the untreated and the electrochemically pretreated CNT web electrodes towards the amperometric detection of NADH (R(2) of 0.9996 and 0.9986 respectively) while a non-linear response was observed for the plasma pretreated CNT web electrode (R(2) of 0.8538). The pretreated CNT web electrodes enabled the fabrication of a LBL biosensor for alcohol detection with highest operational stability obtained for the plasma pretreated CNT web surface.

Carbon nanotube-ionic liquid composite sensors and biosensors.

A new composite electrode has been fabricated using multiwall carbon nanotubes (MWCNT) and the ionic liquid n-octylpyridinum hexafluorophosphate (OPFP). This electrode shows very attractive electrochemical performances compared to other conventional electrodes using graphite and mineral oil, notably improved sensitivity and stability. One major advantage of this electrode compared to other electrodes using carbon nanotubes and other ionic liquids is its extremely low capacitance and background currents. A 10% (w/w) loading of MWCNT was selected as the optimal composition based on voltammetric results, as well as the stability of the background response in solution. The new composite electrode showed good activity toward hydrogen peroxide and NADH, with the possibility of fabricating a sensitive biosensor for glucose and alcohol using glucose oxidase and alcohol dehydrogenase, respectively, by simply incorporating the specific enzyme within the composite matrix. The marked electrode stability and antifouling features toward NADH oxidation was much higher for this composite compared to a bare glassy carbon electrode. While a loading of 2% MWCNT showed very poor electrochemical behavior, a large enhancement was observed upon gentle heating to 70 degrees C, which gave a response similar to the optimum composition of 10%. The ease of preparation, low background current, high sensitivity, stability, and small loading of nanotubes using this composite can create new novel avenues and applications for fabricating robust sensors and biosensors for many important species.

Ionic liquid-carbon composite glucose biosensor.

The use of ionic liquids that are solid at room temperature such as n-octyl-pyridinium hexafluorophosphate (nOPPF(6)) is shown to be advantageous in the fabrication of new form of biocomposite materials with attractive performance over other types of composites and pastes involving non-conductive binders. The resulting IL/graphite material brings new capabilities for electrochemical devices by combining the advantages of ILs and "bulk" composite electrodes. The electrocatalytic properties of the ILs are not impaired by their association with the graphite powder. The marked electrocatalytic activity towards hydrogen peroxide permits effective amperometric biosensing of glucose in connection with the incorporation of glucose oxidase within the three-dimensional IL/graphite matrix. The accelerated electron transfer is coupled with low background current and improved linearity. The advantages of these IL-based biocomposite devices are illustrated from comparison to conventional mineral oil/graphite biocomposite. The influence of the IL and glucose oxidase (GOx) loading upon the amperometric and voltammetric data, as well as the electrode capacitance and resistance, is examined. The preparation of IL/graphite composites overcomes a major obstacle for creating IL-based biosensing devices and expands the scope of IL-based electrochemical devices.

Sensitive and stable amperometric measurements at ionic liquid-carbon paste microelectrodes.

Ionic liquids (ILs) were utilized in preparing carbon paste electrodes with improved sensitivity, linearity, and stability. In order to overcome the large capacitance encountered with these pastes which affects the measured signal, microelectrodes were used to minimize the background current and improve the signal to background response. A number of ILs were tested including those having the same anions, such as butyl, hexyl, and octyl hexafluorophosphate (PF(6)), and those having the same cation, including hexyl-imide, trifluorophosphate (PF(3)) and PF(6). Based on the structure of each ILs, different responses were obtained. Several probes were utilized for those studies including hydrogen peroxide, acetaminophen, and ascorbic acid. The butyl-methyl-imidazolium (BMI)-PF(6) displayed the highest response among other ILs with similar anions and the smallest peak separation. The optimum ILs loading in terms of electrode resistance, capacitance, and peak separation was 30-40%. Improved resistance to surface fouling was observed at the ILs-carbon paste electrode compared to that using mineral oil when tested for NADH detection. Very good linearity up to 1mM hydrazine (correlation coefficient 0.996) was obtained using the ILs-carbon paste electrode.

Enhanced stability and sensitivity of ionic liquid-carbon paste electrodes at elevated temperatures.

We describe the operation of ionic liquid-carbon paste electrodes at elevated temperatures and the effect of heating on the electrode performance and response. Using cyclic and square wave voltammetry and amperometry, it is shown that signals can be enhanced and stabilized by increasing the temperature of the operating solution. At low temperature, the electrode was susceptible to electrode fouling and showed poor stability, sensitivity, and linearity. An order of magnitude improvement of response for ascorbic acid was possible by operating the electrode at 60 degrees C compared to 0 degrees C. This study represents the first report showing that the analytical response of ionic liquid-carbon paste electrodes can be improved by operating them at elevated temperatures for a number of applications.

Acid stability of carbon paste enzyme electrodes.

This note reports on the unusual protection of several enzymes against harsh pH conditions provided by carbon paste electrodes. Both glucose oxidase and polyphenol oxidase carbon paste amperometric biosensors display a remarkable resistance to acid deactivation compared to conventional biosensors prepared by electropolymeric entrapment of enzymes. For example, the carbon paste enzyme electrodes fully retain their activity upon stressing in strongly acidic conditions (pH approximately 2.0-2.5) for prolonged periods, where conventional (polymer-based) biosensors rapidly lose most of their response. Such unusual acid stability of carbon paste enzyme electrodes is attributed to the "pH memory" of enzymes in the hydrophobic paste environment, to the barrier to hydronium ions provided by the pasting liquid and to decreased conformational mobility.

Capillary electrophoresis microchip with a carbon nanotube-modified electrochemical detector.

Significant improvements in the performance of a capillary electrophoresis (CE) microchip with an electrochemical detector are observed using a carbon nanotube (CNT)-modified working electrode. The CNT-modified electrode allows CE amperometric detection at significantly lower operating potentials and yields substantially enhanced signal-to-noise characteristics. The electrocatalytic detection is coupled to resistance to surface fouling and hence enhanced stability. Such advantages are illustrated in connection with several classes of hydrazine, phenol, purine, and amino acid compounds. Substantial minimization of surface fouling effects has been demonstrated in connection with the monitoring of phenol and tyrosine. Factors affecting the performance of the new CNT detector were assessed and optimized. CNTs from different sources are evaluated, and the effect of an anodic pretreatment is explored. The broad and significant catalytic activity exhibited by CNT-based CE detectors indicates great promise for a wide range of bioanalytical and environmental applications.

Carbon nanotube screen-printed electrochemical sensors.

The fabrication, and evaluation of carbon-nanotube (CNT)-derived screen-printed (SP) electrochemical sensors based on a CNT ink are reported. The fabricated CNT strips combine the attractive advantages of CNT materials and disposable screen-printed electrodes. Such thick-film CNT sensors have a well-defined appearance, are mechanically stable, and exhibit high electrochemical reactivity.

Carbon-nanotube-modified glassy carbon electrodes for amplified label-free electrochemical detection of DNA hybridization.

The preparation and attractive performance of carbon-nanotube modified glassy-carbon (CNT/GC) electrodes for improved detection of purines, nucleic acids, and DNA hybridization are described. The surface-confined multiwall carbon-nanotube (MWCNT) facilitates the adsorptive accumulation of the guanine nucleobase and greatly enhances its oxidation signal. The advantages of CNT/GC electrodes are illustrated from comparison to the common unmodified glassy carbon, carbon paste and graphite pencil electrodes. The dramatic amplification of the guanine signal has been combined with a label-free electrical detection of DNA hybridization. Factors influencing the enhancement of the guanine signal are assessed and optimized. The performance characteristics of the amplified label-free electrochemical detection of DNA hybridization are reported in connection to measurements of nucleic-acid segments related to the breast-cancer BRCA1 gene.

Carbon nanotube/teflon composite electrochemical sensors and biosensors.

The fabrication and attractive performance of carbon nanotube (CNT)/Teflon composite electrodes, based on the dispersion of CNT within a Teflon binder, are described. The resulting CNT/Teflon material brings new capabilities for electrochemical devices by combining the advantages of CNT and "bulk" composite electrodes. The electrocatalytic properties of CNT are not impaired by their association with the Teflon binder. The marked electrocatalytic activity toward hydrogen peroxide and NADH permits effective low-potential amperometric biosensing of glucose and ethanol, respectively, in connection with the incorporation of glucose oxidase and alcohol dehydrogenase/NAD(+) within the three-dimensional CNT/Teflon matrix. The accelerated electron transfer is coupled with minimization of surface fouling and surface renewability. These advantages of CNT-based composite devices are illustrated from comparison to their graphite/Teflon counterparts. The influence of the CNT loading upon the amperometric and voltammetric data, as well as the electrode resistance, is examined. SEM images offer insights into the nature of the CNT/Teflon surface. The preparation of CNT/Teflon composites overcomes a major obstacle for creating CNT-based biosensing devices and expands the scope of CNT-based electrochemical devices.