Facile Synthesis of Poly(methyl methacrylate) Silica Nanocomposite Monolith by In Situ Free Radical Polymerization of Methyl Methacrylate in the Presence of Functionalized Silica Nanoparticles.

Novel porous poly(methyl methacrylate) (PMMA) silica nanocomposites have been produced by utilization of polymerization-induced phase separation in a simple one-pot approach. A facile free radical polymerization of MMA in the presence of surface methacrylate-functionalized silica nanoparticles was carried out in ethanol-based solvents, successfully producing novel, morphologically designable porous nanocomposite monoliths. Differing from standard free radical polymerization in solution, a mixture of good and poor solvents (ethanol/N,N-dimethylformamide ratio) for the resulting polymer was used to trigger spinodal phase separation. The influence of monomer concentration, as well as solvent composition, on the morphology of the resulting porous polymers has been investigated. Porous monolith structures composed of connected particles and co-continuous morphologies were observed under a scanning electron microscope depending on the polymerization conditions. The resulting polymers were insoluble and showed swelling characteristics in some organic solvents that are capable of dissolving regular PMMA, indicating covalent bonds between the functionalized silica nanoparticles and the polymer chains. The presence of silica particles in the final polymer was proven via an ATR-IR analysis. The glass transition temperature of the present PMMA-silica nanocomposite was higher than that of the conventional PMMA. The porous polymer immersed in a mixed organic solvent showed coloration induced by the Christiansen effect.

Amplified Chirality Transfer to Aromatic Molecules through Non-specific Inclusion by Amorphous, Hyperbranched Poly(fluorenevinylene) Derivatives.

Optically active, hyperbranched, poly(fluorene-2,4,7-triylethene-1,2-diyl) [poly(fluorenevinylene)] derivatives bearing a neomenthyl group and a pentyl group at the 9-position of the fluorene backbone at various ratios acted as a chirality donor (host polymers) efficiently included naphthalene, anthracene, pyrene, 9-phenylanthracene, and 9,10-diphenyanthracene as a chirality acceptor (guest molecules) in their interior space in film as well as in solution, with the guest molecules exhibiting intense circular dichroism through chirality transfer with chirality amplification. The efficiency of the chirality transfer was much higher with higher-molar-mass polymers than lower-molar-mass ones as well as with hyperbranched polymers compared to the analogous linear ones. The hyperbranched polymers include the small molecules in their complex structure without any specific interactions at various stoichiometries. The included molecules may have ordered intermolecular arrangement that may be somewhat similar to those of liquid crystals. Naphthalene, anthracene, and pyrene included in the polymer exhibited efficient circularly polarized luminescence, where the chirality was remarkably amplified in excited states, and anthracene exhibited especially high anisotropies in the emission on the order of 10-2 .

The first space-filling polyhedrons of polymer cubic cells originated from Weaire-Phelan structure created by polymerization induced phase separation.

The Weaire-Phelan structure is a three-dimensional structure composed of two different polyhedra having the same volume, i.e., pyritohedron and truncated hexagonal trapezohedron. It was proposed by Weaire and Phelan in 1993 as a solution of the Kelvin problem of filling space with no gaps with cells of minimum surface area and equal volume. It was found in physical systems including liquid foam and a metal alloy while it has never been constructed as organic materials. We report herewith the first polymeric Weaire-Phelan structure constructed through phase-separation of a single polymer species that is synthesized by simple polyaddition between tetrakis(3-mercaptopropionate) and 1,6-diisocyanatohexane. The structure has the order of micrometers and is amorphous unlike reported crystal structures similar to the Weaire-Phelan structure.

Non-uniform Self-folding of Helical Poly(fluorenevinylene) Derivatives in the Solid State Leading to Amplified Circular Dichroism and Circularly Polarized Light Emission.

An unprecedented non-uniform self-folding of artificial polymer chains composed of turn moieties and stretched segments is presented through the design of a set of optically active poly(fluorene-2,7-diylethene-1,2-diyl) (poly(fluorenevinylene)) derivatives bearing a neomenthyl group and a pentyl group attached at the 9-position of fluorene backbone at various ratios. The folded structure is formed and stabilized through inter-chain interactions in the solid state, leading to remarkably enhanced chiroptical properties (chirality amplification) in terms of circular dichroism (CD) and circularly polarized light (CPL) emission. This phenomenon is rationalized by experimental and theoretical CD and CPL spectral analyses. The polymer arrangements in the solid state were further assessed through transmission electron microscopic observations combined with enhanced sampling molecular dynamics simulations in the solid state revealing the thin film organizations.

Ring-Opening Polymerization of Triaziridine Compounds in Water: An Extremely Facile Method to Synthesize a Porous Polymer through Polymerization-Induced Phase Separation.

Dissolution of trifunctional aziridine compounds, 2,2-bishydroxymethylbutanol-tris[3-(1-aziridinyl)propionate] (3AZ) and tetramethylolmethane-tri-ß-aziridinylpropionate (3AZOH), in water initiates a ring-opening polymerization and successful yields the corresponding network polymers via cationic polymerization. The polymerization of 3AZ induced phase separation and produced porous polymers under a wide range of monomer concentrations and polymerization temperatures. The phase separation rate in the 3AZ/water system was estimated by quantifying the turbidity by means of light transmission where transmittance decreased with an increase in the content of phase-separated materials. The rate increased with an increase in reaction temperature. The 3AZ porous polymers showed characteristic surface morphologies, which were formed by connected particles with diameters of about 4-5 µm. The porous polymers were not breakable by the compression test under 50 N. The Young's modulus of the 3AZ porous polymers increased with an increase in polymerization temperature, which may be accounted for by cross-linking through the formation of quaternary ammonium salt formed by a termination reaction. The 3AZ porous polymer absorbed various solvents.

Aggregation-induced chirality amplification of optically active fluorescent polyurethane and a cyclic dimer in the ground and excited states.

Optically active linear polyurethane and a cyclic dimer were synthesized from 2,7-diisocyanatofluorene and 2,2'-dihydroxy-1,1'-binaphthyl. The circular dichroism (CD) spectral intensity of the polymer was amplified at a higher concentration through aggregate formation, while circularly polarized light (CPL) emission was not enhanced. The cyclic dimer's CPL emission was largely amplified (glum 1.1 × 10-2) due to intermolecular excimer formation through aggregation, while the CD intensity was not affected.

Photo racemization of 2,2'-dihydroxy-1,1'-binaphthyl derivatives.

Photo racemization of 2,2'-dihydroxy-1,1'-binaphthyl (BINOL) and its monomethyl ether, monobutyl ether, and dimethyl ether was studied by means of circularly dichroism spectra, chiral HPLC, and theoretical calculations of rotation energy barriers. Racemization was fastest for BINOL and about one seventh as fast for the monomethyl and monobutyl ethers while it was too slow to be detected for the dimethyl ether under the present conditions.

Optically active covalent organic frameworks and hyperbranched polymers with chirality induced by circularly polarized light.

Axial chirality was induced by circularly polarized light to covalent organic frameworks as well as hyperbranched polymers composed of bezene-1,3,5-triyl core units and oligo(benzene-1,4-diyl) as linker units where variation in induction efficiency was rationally interpreted in terms of internal rotation dynamics studied through CPMAS 13C NMR experiments including CODEX measurements.

Morphology Control and Metallization of Porous Polymers Synthesized by Michael Addition Reactions of a Multi-Functional Acrylamide with a Diamine.

Porous polymers have been synthesized by an aza-Michael addition reaction of a multi-functional acrylamide, N,N',N″,N‴-tetraacryloyltriethylenetetramine (AM4), and hexamethylene diamine (HDA) in H2O without catalyst. Reaction conditions, such as monomer concentration and reaction temperature, affected the morphology of the resulting porous structures. Connected spheres, co-continuous monolithic structures and/or isolated holes were observed on the surface of the porous polymers. These structures were formed by polymerization-induced phase separation via spinodal decomposition or highly internal phase separation. The obtained porous polymers were soft and flexible and not breakable by compression. The porous polymers adsorbed various solvents. An AM4-HDA porous polymer could be plated by Ni using an electroless plating process via catalyzation by palladium (II) acetylacetonate following reduction of Ni ions in a plating solution. The intermediate Pd-catalyzed porous polymer promoted the Suzuki-Miyaura cross coupling reaction of 4-bromoanisole and phenylboronic acid.

Joint-Linker Type Ionic Gels Using Polymerizable Ionic Liquid as a Crosslinker via Thiol-Ene Click Reactions.

In this work, we report the synthesis of ion-conductive gels, or ionic gels, via thiol-ene click reactions. The novel gel systems consist of the multifunctional thiol monomers tris[(3-mercaptopropionyloxy)-ethyl]-isocyanurate (TEMPIC), pentaerythritol tetrakis(3-mercaptopropionate) (PEMP), and dipentaerythritol hexakis(3-mercaptopionate) (DPMP) as joint molecules and bifunctional allyl ionic liquid (IL) as a crosslinker. The thiol-ene reaction was carried out in lithium bis(trifluoromethanesulfonyl)imide (Li-TFSI) in a propylene carbonate (PC) (1 M) solvent system via a photopolymerization process. The chemical structure and mechanical, thermal, and conductive properties of the gels were investigated using Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), compression tests, and impedance spectroscopy, respectively. The mechanical and conductive properties of the ionic gels were found to be largely dependent on the monomer content and functionalities of the joint molecules. TGA revealed good thermal stability of the gels up to 100 °C. An ionic conductivity of 4.89 mS cm-1 was realized at room temperature (298 K) for low-functional thiol monomers, and a further increase in ionic conductivity was observed with an increase in Li+ ion content and temperature.

Synthesis of Network Polymers by Means of Addition Reactions of Multifunctional-Amine and Poly(ethylene glycol) Diglycidyl Ether or Diacrylate Compounds.

Addition reactions of multi-functional amine, polyethylene imine (PEI) or diethylenetriamine (DETA), and poly(ethylene glycol) diglycidyl ether (PEGDE) or poly(ethylene glycol) diacrylate (PEGDA), have been investigated to obtain network polymers in H2O, dimethyl sulfoxide (DMSO), and ethanol (EtOH). Ring opening addition reaction of the multi-functional amine and PEGDE in H2O at room temperature or in DMSO at 90 °C using triphenylphosphine as a catalyst yielded gels. Aza-Michael addition reaction of the multi-functional amine and PEGDA in DMSO or EtOH at room temperature also yielded corresponding gels. Compression test of the gels obtained with PEI showed higher Young's modulus than those with DETA. The reactions of the multi-functional amine and low molecular weight PEGDA in EtOH under the specific conditions yielded porous polymers induced by phase separation during the network formation. The morphology of the porous polymers could be controlled by the reaction conditions, especially monomer concentration and feed ratio of the multi-functional amine to PEGDA of the reaction system. The porous structure was formed by connected spheres or a co-continuous monolithic structure. The porous polymers were unbreakable by compression, and their Young's modulus increased with the increase in the monomer concentration of the reaction systems. The porous polymers absorbed various solvents derived from high affinity between the polyethylene glycol units in the network structure and the solvents.

Synthesis and properties of porous polymers synthesized by Michael addition reactions of multi-functional acrylate, diamine, and dithiol compounds.

Porous polymers have been synthesized by Michael addition reactions of multi-functional acrylate and diamine or dithiol compounds. Aza-Michael addition reaction of multi-functional acrylate, trimethylolpropane propoxylate triacrylate (TPT) and hexamethylene diamine (HDA) in dimethyl sulfoxide (DMSO) successfully yielded the porous polymer. The porous structure was characterized by connected globules or co-continuous structure, and could be controlled by the reaction conditions. Mechanical properties of the porous polymers were investigated by compression test. The porous polymers with co-continuous structure showed higher Young's modulus than those with connected globules. The porous polymer absorbed some organic solvents, especially CHCl3. The porous polymer as prepared in DMSO state showed coloring induced by Christiansen filter effect depending on the reaction time and observation temperature. The thio-Michael addition reaction of TPT and 1,6-hexanedithiol (HDT) in DMSO using different base catalysts also yielded the porous polymer. The porous structure could be controlled by the catalysts amount when the reaction was initiated by a photo-base generator as the base catalyst. The present reaction systems make it possible to synthesize the porous polymers with simple process without phase separator.

Silk-pectin hydrogel with superior mechanical properties, biodegradability, and biocompatibility.

A new method is developed to prepare silk hydrogels and silk-pectin hydrogels via dialysis against methanol to obtain hydrogels with high concentrations of silk fibroin. The relationship between the mechanical and biological properties and the structure of the silk-pectin hydrogels is subsequently evaluated. The present results suggest that pectin associates with silk molecules when the silk concentration exceeds 15 wt%, suggesting that a silk concentration of over 15 wt% is critical to construct interacting silk-pectin networks. The silk-pectin hydrogel reported here is composed of a heterogeneous network, which is different from fiber-reinforced, interpenetrated networks and double-network hydrogels, as well as high-stiffness hydrogels (elastic modulus of 4.7 ± 0.9 MPa, elastic stress limit of 3.9 ± 0.1 MPa, and elastic strain limit of 48.4 ± 0.5%) with regard to biocompatibility and biodegradability.

Biocompatible and biodegradable dual-drug release system based on silk hydrogel containing silk nanoparticles.

We developed a facile and quick ethanol-based method for preparing silk nanoparticles and then fabricated a biodegradable and biocompatible dual-drug release system based on silk nanoparticles and the molecular networks of silk hydrogels. Model drugs incorporated in the silk nanoparticles and silk hydrogels showed fast and constant release, respectively, indicating successful dual-drug release from silk hydrogel containing silk nanoparticles. The release behaviors achieved by this dual-drug release system suggest to be regulated by physical properties (e.g., ß-sheet contents and size of the silk nanoparticles and network size of the silk hydrogels), which is an important advantage for biomedical applications. The present silk-based system for dual-drug release also demonstrated no significant cytotoxicity against human mesenchymal stem cells (hMSCs), and thus, this silk-based dual-drug release system has potential as a versatile and useful new platform of polymeric materials for various types of dual delivery of bioactive molecules.