RESUMO
The aim is to develop new fiber-reinforced polymer (FRP) water pipe by activating fiber glass (FG) by vinyltriethoxysilane (VS) getting vinylsilane-activated FG (AFG) for filling vinylester (VE) via continuous winding to make a novel VE-AFG composite. The novelty of this work is the activation of fiber glass by vinylsilane as a single filler in vinylester and compounding them via a two-dimensional continuous winding process for the first time. The crosslinking occurred in the AFG/VE/curing agent system after activation. The activated composites increased thermal stability; 25% VE-AGF increased the degradation temperatures at 10%, 25%, and 50% weight loss by 73.3%, 10%, and 7.2%. With the activated 20% composite, values of axial strength, hoop strength, and hardness were developed by 6.3%, 2%, and 8.7%, respectively. The decay resistance to different microorganisms was increased with VE-AFG composites as a result of a sharp decrease in biodegradability percentages. The activated composites are stable toward water absorption; the least percentage was recorded by 25% VE-AFG, which minimized the water absorptivity by more than 62%. The reported characterization sentence approves enhancement of thermal, physical, and mechanical stability of sustainable vinylester-fiber glass composites manufactured by continuous winding; this is recommended for application in water pipe systems.
RESUMO
The hazards of polymer waste and emitted gas on the environment pose a global challenge. As a trial to control this, the current work aims to reuse the polymer waste mix (PM) as fillers in calcium silicate to prepare new composites of environmentally friendly polymer concrete. PM was first subjected to treatment to obtain treated PM (TPM) and then was filled in new dicalcium silicate cement with different concentrations. The microstructural characterizations declare the successful preparation of the dicalcium silicate base material. After the curing reaction, the precipitated carbonate main product is responsible for the gained properties. The CO2 uptake% in the proposed composites reached 16.6%, referring to the successful storage of CO2 gas during curing. The treatment reaction led to an increase in the flexural and compression strengths due to the strengthening of the polymer waste mix-cement interface; the strengths were increased gradually with more contents of TPM fillers. 7% TPM-cement concentration achieved the highest flexural strength and compression strength of10.2 and 12.7%, respectively, compared with blank cement. The used polymer improved slightly the pull-off force of the prepared cement, and 7 and 5% TPM-cement composites have the maximum values. All the proposed composites passed the impact testing without failure, where the combination between the polymer waste and silicate cement resulted in a stable composite surface. Compared with the blank, the different concentrations of TPM-cement composites show more stability against water absorption. In addition, the proposed composites and blank cement have a very low carbon dioxide emission. The ability to recycle the polymer waste, form new type of low-energy silicate, improve the mechanical and surface properties, uptake CO2 gas, and reduce gas emission makes the proposed polymer waste mix-cement composites as environmentally friendly construction products.
RESUMO
The present study focuses on enhancing the mechanical, thermal, and degradation behavior of polylactic acid (PLA) by adding carbon nanotubes (CNTs) with different concentrations of 0.5, 1, 3, and 5%. The CNTs were prepared using catalytic chemical vapor deposition, and the prepared PLA/CNTs nanocomposite films were characterized using techniques such as FT-IR, Raman spectroscopy, TGA, SEM, and XRD. The distinct diffraction patterns of multi-walled carbon nanotubes (MWCNTs) at 2θ angles of 25.7° and 42.7° were no longer observed in the prepared nanocomposites, indicating uniform dispersion of MWCNTs within the PLA matrix. The presence of MWCNTs enhanced the crystallinity of PLA as the CNT loading increased. Mechanical tests demonstrated that incorporating CNTs positively influenced the elongation at the break while decreasing the ultimate tensile strength of PLA. The PLA-3%CNTs composition exhibited the highest elongation at break (51.8%) but the lowest tensile strength (64 MPa). Moreover, thermal gravimetric analysis confirmed that the prepared nanocomposites exhibited greater thermal stability than pure PLA. Among the nanocomposites, PLA-5% CNTs exhibited the highest thermal stability. Furthermore, the nanocomposites demonstrated reduced surface degradation in accelerated weathering tests, with a more pronounced resilience to UV radiation and moisture-induced deterioration observed in PLA-3% CNTs.
RESUMO
Climate change is being currently faced globally; controlling the plastic waste and gas emission is aimed to reduce their hazardous effects. In this work, polyethylene terephthalate (PET) and polyvinyl chloride (PVC) polymer wastes are used as fillers to calcium silicate. Chemical treatment was performed to get the best efficiency of the binder material with the treated PET (TPET) and treated PVC (TPVC). The used silicate, new nonhydraulic dicalcium silicate, was synthesized by sintering. A new environmentally friendly polymer concrete, based on different concentrations of PET-/TPET-/PVC-/TPVC-dicalcium silicate composites, was prepared and cured by carbonation. FTIR analysis confirms that the treatment gave functional groups on the polymer surface; also, the hydrophilicity was increased after treatment. SEM photos show that the treated polymers have a rougher surface, which led to improved attachment with cement. The structures of the prepared and cured cement materials are proved by XRD, FTIR analysis, and SEM, through the change of calcium silicate to carbonate. Carbon footprint is used to analyze the environmental implications of the prepared composites. After the treatment reaction, the TPET-cement and TPVC-cement composites showed improved compression and flexural properties and more stability against water absorption. The novelty arises from recycling this plastic waste in the proposed low-energy dicalcium silicate cement, for the first time, to give improved environmentally friendly composites after converting CO2 gas to carbonates, with the reduced carbon footprint.