Effect of gum-chewing exercise on maintaining and improving oral function in older adults: A pilot randomized controlled trial.

Background/purpose: Gum chewing has been found to improve oral function. Nevertheless, few randomized controlled trials have investigated the effects of gum-chewing exercises on oral function in older adults. This study aimed to examine the effect of gum-chewing exercises on oral function in older adults. Materials and methods: This was a single-blind, randomized controlled trial, conducted from November 2021 to January 2022. A total of 130 participants were divided randomly into the intervention and control groups. The intervention group was told to chew experimental gums for one month, while the control group was instructed to chew experimental tablets for one month. Maximum bite force, occlusal contact areas, oral dryness, tongue pressure, tongue and lip functions (number of times each of the following syllables is pronounced per second:/pa/,/ta/, and/ka/), masticatory function, subjective masticatory function, and gum-chewing time were measured at baseline and one month following intervention to assess outcomes. Results: One month following the intervention, tongue pressure was significantly higher in the intervention group than in the control group (P = 0.027). In the within-group comparisons, maximum bite force (P < 0.001), unstimulated saliva flow (P < 0.001), tongue and lip functions (/pa/: P < 0.001;/ta/: P < 0.001;/ka/: P < 0.001), color scale value (P = 0.019), and ΔE value (P = 0.024) were significantly increased in the intervention group. Conclusion: The results suggest that gum-chewing exercises can improve oral functions in older adults, although additional increases in masticatory load may be necessary to establish a more effective oral function training method using gum-chewing exercises in older adults.

Osteoblast Response of Additively Manufactured Zirconia and Alumina-Toughened Zirconia.

Zirconia ceramics have been widely used in dentistry. Herein, we assess the surface morphology, surface texture, and osteoblast response of additively manufactured zirconia and alumina-toughened zirconia (ATZ) in comparison with titanium. The surface roughness, contact angle, and surface microstructure of titanium sandblasted with large-grit alumina and subsequently acid-etched using 18% HCl and 49% H2SO4 (SLA-titanium), uniaxially pressed zirconia (UP zirconia), additively manufactured zirconia (AM zirconia), and additively manufactured ATZ (AM ATZ) were investigated. Moreover, the cell viability, alkaline phosphatase (ALP) activity, and gene expression of type I collagen on these materials were evaluated. The data were statistically analyzed using one-way ANOVA with Tukey's post hoc test. SLA-titanium showed the highest surface roughness and contact angle. The other three materials showed comparable surface roughness and contact angles. Micro- and nanoroughness were observed on the surface of SLA-titanium. UP zirconia and AM zirconia had similar surface morphologies. The cell viability, ALP activity, and gene expression of type I collagen on AM zirconia were comparable to or better than those on SLA-titanium. Our results indicate that AM zirconia is a promising material for zirconia dental implants.

Influence of high-speed sintering protocols on translucency, mechanical properties, microstructure, crystallography, and low-temperature degradation of highly translucent zirconia.

OBJECTIVES: Impacts of high-speed sintering on the optical and mechanical properties, microstructure, crystallography, and low-temperature degradation of commercial yttria-partially stabilized zirconia (Y-PSZ) were investigated. METHODS: Five commercial Y-PSZ products (KATANA HT, KATANA STML, KATANA UTML, Zpex 4, and Zpex Smile) were investigated. Specimens were sintered following speed-sintering (~90 min) and conventional-sintering protocols (~7 h), and a group of KATANA STML was super-speed-sintered (18 min). Dimensions of the zirconia specimens after sintering were 14.5 mm (diameter) and 1.2 mm (thickness). Translucency was assessed using a colorimeter. Biaxial flexural strength was measured using a universal testing machine, followed by Weibull analysis. Scanning electron microscopy was used for microstructure assessments. X-ray diffraction was used to analyze the crystallography before and after hydrothermal aging. Low-temperature degradation (LTD) tests were performed at 134 °C under 2-3 bar water vapor in an autoclave. RESULTS: The translucency and flexural strength were not affected significantly by the sintering programs (p > 0.05). The conventionally sintered KATANA STML and speed-sintered Zpex 4 presented the highest and lowest Weibull modulus, respectively. The conventionally-sintered Y-PSZ had a larger average grain size and smaller fraction of fine grains than those of the speed-sintered specimens. The fractographic analysis of the speed- and conventionally sintered Y-PSZ yielded comparable results. The speed-sintered Y-PSZ exhibited a lower c-ZrO2 content than that of conventionally-sintered Y-PSZ, except for KATANA HT and KATANA STML. LTD tests indicated that some of the speed and conventionally-sintered Y-PSZ exhibited similar monoclinic volume fractions. SIGNIFICANCE: Speed-sintering programs are acceptable for Y-PSZ zirconia.

Influence of sintering conditions on translucency, biaxial flexural strength, microstructure, and low-temperature degradation of highly translucent dental zirconia.

There is limited research on the influence of different sintering temperatures on the properties of highly translucent zirconia ceramics. This study demonstrated the influence of different sintering temperatures on the translucency, crystallographic structure, biaxial flexural strength, microstructure, and low-temperature degradation (LTD) of three highly translucent zirconia grades, i.e., 3 mol% yttria-stabilized tetragonal zirconia polycrystals (3Y-TZP), 4 mol% yttria-partially-stabilized zirconia (4Y-PSZ), and 5 mol% yttria-PSZ (5Y-PSZ). The specimens were characterized using colorimetry, X-ray diffraction, scanning electron microscopy, Weibull analysis, and LTD tests (134°C; 20 h). The increase in the sintering temperature did not affect the translucency of 3Y-TZP, whereas it increased the translucencies of 4Y-PSZ and 5Y-PSZ. All the zirconia grades exhibited grain enlargement and unchanged biaxial flexural strengths with the increase in the sintering temperature. The degradation of 3Y-TZP and 4Y-PSZ at a sintering temperature of 1,600°C was faster than that at other sintering temperatures.

Additively Manufactured Zirconia for Dental Applications.

We aimed to assess the crystallography, microstructure and flexural strength of zirconia-based ceramics made by stereolithography (SLA). Two additively manufactured 3 mol% yttria-stabilized tetragonal zirconia polycrystals (3Y-TZP: LithaCon 3Y 230, Lithoz; 3D Mix zirconia, 3DCeram Sinto) and one alumina-toughened zirconia (ATZ: 3D Mix ATZ, 3DCeram Sinto) were compared to subtractively manufactured 3Y-TZP (control: LAVA Plus, 3M Oral Care). Crystallographic analysis was conducted by X-ray diffraction. Top surfaces and cross-sections of the subsurface microstructure were characterized using scanning electron microscopy (SEM). Biaxial flexural strength was statistically compared using Weibull analysis. The additively and subtractively manufactured zirconia grades revealed a similar phase composition. The residual porosity of the SLA 3Y-TZPs and ATZ was comparable to that of subtractively manufactured 3Y-TZP. Weibull analysis revealed that the additively manufactured LithaCon 3Y 230 (Lithoz) had a significantly lower biaxial flexural strength than 3D Mix ATZ (3D Ceram Sinto). The biaxial flexural strength of the subtractively manufactured LAVA Plus (3M Oral Care) was in between those of the additively manufactured 3Y-TZPs, with the additively manufactured ATZ significantly outperforming the subtractively manufactured 3Y-TZP. Additively manufactured 3Y-TZP showed comparable crystallography, microstructure and flexural strength as the subtractively manufactured zirconia, thus potentially being a good option for dental implants.