Advanced Ceramics with Dual Functions of Healing and Decomposition.

This study developed advanced ceramic materials with both healing and decomposition functions using a metastable product generated under superheated steam. The developed composite material comprises ZrC particles dispersed in a yttria-stabilized zirconia (YSZ) matrix. After introducing a surface crack of approximately 120 µm on the composite specimen, it showed a complete strength recovery rate after one hour of heat treatment under superheated steam at 400 °C, while it exhibited a decomposition behavior after one hour of heat treatment in air at 400 °C. The XRD analysis of the heat-treated specimens showed that the final product was monoclinic ZrO2 under both steam and air conditions. In other words, full strength recovery in superheated steam was achieved by a chain reaction involving metastable intermediate products derived from H2O, unlike the reaction in air.

Critical-sized marginal defects around implants in the rabbit mandible.

BACKGROUND: The mandible of the rabbit is considered a reliable model to be used to study bone regeneration in defects. The aim of the present study was to evaluate the formation of new bone around implants installed in defects of either 5 or 10 mm in the mandible of rabbits. MATERIALS AND METHODS: In 12 rabbits, 3 mm deep circumferential defect, either 5 or 10 mm in diameter, were prepared bilaterally and an implant was placed in the center. A collagen membrane was placed to close the entrance. After 10 weeks, biopsies were taken, histological slides were prepared, and different regions of the defects were analyzed. RESULTS: Similar amounts of new bone were found in both defects. However, most of the 5 mm defects were filled with new bone. New bone was observed closing the entrance of the defect and laid onto the implant surface. Only in a few cases the healing was incomplete. Despite a similar percentage of new bone found within the 10 mm defects, the healing was incomplete in most of the cases, presenting a low rate of bone formation onto the implant surface within the defect. Only one case presented the closure of the entrance. CONCLUSIONS: The dimensions of the defect strongly influenced the healing so that a circumferential marginal defect of 10 mm around an implant in the mandible body should be considered a critical-sized defect. The presence of the implant and of residues of teeth might have strongly influenced the healing.

Critical-sized marginal defects around implants treated with xenografts in rabbits.

BACKGROUND: Healing of critical-size defects is a well-known problem that has been challenged in several studies. The aim of the experiment was to evaluate bone formation and osseointegration of implants installed in critical defects of the mandibular body simultaneously grafted with Bio-Oss® or Cerabone®. MATERIAL AND METHODS: Defects, 10 mm wide and 3 mm deep, were prepared at both lateral aspects of the mandible in 12 rabbits. One implant was installed in the center of the defect, and bovine xenografts produced either at low (Bio-Oss®; Low-T) or high (Cerabone®; High-T) temperatures were used to fill the defects. A collagen membrane was placed to cover the sites. Healing was evaluated 10 weeks after surgery. RESULTS: In both groups, most sites showed optimal healing with closure of the coronal entrance of the defects. However, residual defects occupied by soft tissues and biomaterial particles were observed, even though generally limited to some regions of the defect. Osseointegration of the implant surface in the region of the defect was poor in both groups. CONCLUSIONS: Circumferential marginal critical-size defects around implants filled with bovine xenografts presented regions with a complete healing in both groups. However, the healing was not complete at all regions in most defects; therefore, a complete optimal healing of critical-size marginal defects cannot be predicted.

Implants Placed with a Ring Technique Using Inlay and Onlay Block Xenografts in the Mandible of Rabbits.

BACKGROUND: Xenogenous bone has been proposed as an alternative to overcome the disadvantages of autogenous grafting. The aim of the present study was to study bone dynamics at inlay and onlay xenografts used for bone augmentation applying a ring technique. METHODS: The bone at the lateral surface of the mandibular angle of 12 adult male New Zealand White rabbits was exposed bilaterally. The cortical layer received multiple perforations on one side of the mandible, and a xenograft block of collagenated cancellous equine bone, 7 mm in diameter and 3 mm in width, was fixed on the prepared surface using an implant (onlay group). On the opposite side, a defect 7 mm in diameter and 3 mm in depth was prepared, and the xenograft block was adapted to the defect and fixed with an implant (inlay group). RESULTS: After ten weeks of healing, in the onlay grafts, new bone was mainly formed on the trabeculae surface, reaching in some specimens the most coronal regions of the block. In the inlay grafts, new bone was found arranged on the trabecular surfaces but also occupying the spaces among the trabeculae. The entrance of the defect was often found close to the top of the block by newly formed bone. A higher percentage of new bone was found in the inlay (19.0 ± 9.3%) compared to the onlay (10.4 ± 7.4%) groups (p = 0.031). The mean gain in osseointegration at the implant in relation to the base of the original 3 mm deep defect was 0.95 ± 1.05% in the onlay group and 0.78 ± 0.71% in the inlay group (p = 0.603). CONCLUSION: The inlay grafts exhibited a higher new bone percentage than the onlay block grafts possibly due to the defect conformation that presented more sources for bone growth. The trabecular conformation and the composition of the grafts made possible the expression of the osteoconductive properties of the material used. This resulted, in several specimens, in the growth of bone on the graft trabeculae toward the most superior regions in both groups and in the closure of the coronal entrance of the defects in the inlay group. The clinical relevance of this experiment is that the ring technique applied as an inlay method could be suitable for bone augmentation.

Histological Comparison of Collagenated Cancellous Equine Bone Blocks Used as Inlay or Onlay for Lateral Bone Augmentation in Rabbits.

BACKGROUND: The conformation of the recipient site for an inlay graft presents an increased contact with the parent bone compared to an onlay graft. This might favor bone growth within the inlay compared to onlay grafts. Hence, the objective of this study was to compare the bone incorporation and remodeling processes of xenogeneic en bloc grafts placed using two bone grafting techniques, i.e., onlay vs. inlay. METHODS: In this prospective, randomized, split-mouth study (test and control sides in the same animal), two bone grafting techniques were comparatively evaluated. The lateral aspect of the rabbit mandible was used as the recipient site, bilaterally. On one side of the mandible, the cortical bone was perforated with drills to allow a better bone formation from the bone wound and the marrow spaces. A xenogeneic bone block was fixed in the center of the prepared region, representing the onlay site. On the other side of the mandible, a 7 mm wide and 3 mm deep circumferential defect was prepared using trephines and drills. A xenogeneic bone block was fixed in the center of the defect, representing the inlay site. Two healing periods were applied in the study: 2 and 10 weeks, each represented by 10 rabbits (n = 10 for each period). RESULTS: After 2 weeks of healing, the mean percentage of new bone was 10.4% and 23.3% at the onlay and inlay grafts, respectively (p = 0.022). After 10 weeks of healing, new bone increased to 13.2% at the onlay sites and 25.4% at the inlay sites (p = 0.080). In the 10-week period, the inlay grafts presented a homogeneous growth of new bone in all regions, while in the onlay grafts, low percentages of new bone were observed in the external regions. CONCLUSION: The percentage of new bone increased faster and was higher in the inlay grafts than in the onlay grafts. This outcome might be related to the self-contained conformation of the recipient site in the inlay group, which offered more sources for new bone formation compared to the one-wall conformation of the recipient sites in the onlay group. The osteoconductive properties of the biomaterial allowed the newly formed bone to reach the most peripheral regions in both groups. The osteoconductive properties of the biomaterial, together with the protection offered by the collagen membrane, allowed marginal closure of the defects by newly formed bone in the inlay group.

Mucosal adhesion phenomenon after maxillary sinus floor elevation: A preclinical study.

AIM: To describe the histological events that occur after maxillary sinus floor elevation when the elevated and undetached sinus mucosa are in close proximity or in contact with each other. MATERIALS AND METHODS: From 76 rabbits, 152 elevated maxillary sinuses were analyzed histologically. Sites without adhesions were classified as "No proximity," whereas the adhesion stages were divided into "Proximity," "Fusion," and "Synechia stages." The width of the pseudostratified columnar epithelium and the distance between the two layers of the elevated and undetached sinus mucosae were measured at various standardized positions. RESULTS: Thirty-one sites presenting with adhesions were found. Twelve sites were in the proximity stage," presenting cilia of the two epithelial layers that were shortened and interlinked within the mucous context. Hyperactivity of the goblet cells was also observed. In the other cases, the hyperplastic epithelium showed attempts to reach the contralateral mucosa. The 15 "fusion stage" sites presented regions with epithelial cells of the two mucosal layers that penetrated each other. Four sites presented "synechiae stages," represented by bridges of connective tissue connecting the two lamina propria. CONCLUSIONS: Close proximity or tight contact between the elevated and undetached mucosa adhering to the bone walls might occur after maxillary sinus floor elevation. This induced hyperplasia of the epithelial cells and adhesion of the two layers until synechiae formation.

Schneiderian Membrane Collateral Damage Caused by Collagenated and Non-Collagenated Xenografts: A Histological Study in Rabbits.

BACKGROUND: The Schneiderian membrane (SM) that is in contact with biomaterial granules may become thinner and eventually perforate. It has been shown that these events are related to the biomaterial used. Hence, the main aim of the present study was to compare the damaging effects of two xenografts with different resorbability rates on SM. The secondary aim was to evaluate the possible protection from damage offered by a collagen membrane placed adjacent to the SM and by inward displacement of the bone window with the SM during elevation. METHODS: Thirty-six albino New Zealand rabbits underwent bilateral sinus elevation. One group of 18 animals received deproteinized bovine bone mineral (DBBM group) and the other received swine-collagenated corticocancellous bone (collagenated group). Moreover, in the DBBM group, the bone window was displaced inward during elevation in one sinus together with the SM. In the collagenated group, a collagen membrane was placed adjacent to the SM in one sinus. Six animals were assessed per period after 2, 4, and 8 weeks. RESULTS: The mean pristine mucosa width ranged between 67 µm and 113 µm, and none had a width of <40 µm. In the 2-week group, the elevated mucosa of the DBBM group presented 59 thinned sites and five perforations, while in the collagenated group, 14 thinned sites and one perforation were observed. Damage to SM decreased in number in the 4-week treatment group. In the 8-week group, the number of thinned sites in the DBBM group increased to 124, and the perforations to 8. In the collagenated group, 7 thinned sites and 1 small perforation were observed. CONCLUSIONS: More damage to the Schneiderian membrane was observed in the DBBM group than in the collagenated group. The presence of the inward bone window offered protection from damage to the Schneiderian membrane.

Healing Patterns of Non-Collagenated Bovine and Collagenated Porcine Xenografts Used for Sinus Floor Elevation: A Histological Study in Rabbits.

Objective: To compare healing of collagenated and non-collagenated xenografts used for maxillary sinus floor elevation. Materials and Methods: Two different xenografts were used: deproteinized bovine bone (DBBM group) and collagenated corticocancellous porcine bone (collagenated group). Healing was studied after 2, 4, and 8 weeks. The loss of dimensions of the elevated area and the percentages of new bone, xenograft remnants, osteoclastic zones, vessels, inflammatory infiltrates, and soft tissues were analyzed. Three regions were evaluated: close to the bone walls (bone wall region), subjacent the sinus mucosa (submucosa region), and the center of the elevated area (middle region). The primary variables were the percentage of new bone and xenograft remnants. Results: Between 2 and 8 weeks, the elevated areas showed a reduction of 16.3% and 52.2% in the DBBM and collagenated groups, respectively (p < 0.01 between the two areas after 8 weeks). After 8 weeks, the highest content of new bone was observed in the bone wall region, which was higher in the collagenated group than in the DBBM group (41.6% and 28.6%, respectively; p < 0.01). A similar quantity of new bone was found between the two groups in other regions. A higher percentage of vessels in all regions evaluated (p < 0.01) and soft tissue in the sub-mucosa region (p < 0.05) was found in the collagenated group than in the DBBM group. Conclusions: The present study showed that both xenografts allowed new bone formation. In comparison with the non-collagenated xenograft, the collagenated xenograft underwent higher resorption, resulting in greater shrinkage of the elevated space after sinus lifting and a higher content of new bone in the regions close to the bone walls. Clinical relevance: In this study, the region adjacent to the bone wall showed the highest new bone content. This region resembles the base of the sinus, closest to the sinus floor and walls, and is the most important region from a clinical point of view because it is where the implant will be installed. Residues of the biomaterial remained after 8 weeks of healing. Other reports have shown that these biomaterial residues may interfere with the integration of implants.

Contribution to Bone Formation of the Schneiderian Membrane after Sinus Augmentation: A Histological Study in Rabbits.

AIM: to evaluate bone formation in close contact with the sinus mucosa after different periods from sinus augmentation and the influence on healing of the presence of an inward dis-placed bone window. MATERIAL AND METHODS: Eighteen rabbits were included in the experiment. A trap-door technique was applied at the test sites, and the bony window was elevated inward (inward window; IW) together with the sinus mucosa. At the control sites, the bony window was removed before the elevation of the sinus mucosa. The elevated space was filled with deproteinized bovine bone mineral (DBBM) and both access windows were covered with a collagen membrane. Histometric measurements were performed subjacent the sinus mucosa after 2, 4, and 8 weeks of healing. RESULTS: Very few sinuses presented small percentages of new bone in close contact with the sinus mucosa in the various period examined. The presence of bone in the neighbor areas might have influenced bone formation close to the sinus mucosa. The inward displaced bone window supported bone formation close to the sinus mucosa only in the earliest period of healing, while the bone walls increased their influence over time. The lack of increased new bone percentage over time in the most central regions of the elevated sinus mucosa do not support the hypothesis that the sinus mucosa may express its potential in bone formation. It can be speculated that the new bone found in the intermediate and middle regions of the control sites in the earliest period of healing might be due to residual of bone from the osteotomy. CONCLUSIONS: Very small amounts of new bone were found subjacent to the sinus mucosa, mostly formed from the bone walls, the inward displaced bone window or from possible bone residues from the osteotomy procedures. The lack of increased new bone percentage over time in the most central regions of the elevated sinus mucosa indicates that the contribution to bone formation provided by the sinus mucosa is limited.

HLA analysis of immune checkpoint inhibitor-induced and idiopathic isolated ACTH deficiency.

PURPOSE: Isolated adrenocorticotropic hormone deficiency is a rare disease; however, since immune check point inhibitors (ICIs) have become widely used, many more cases have been reported. In this study, we compared the human leukocyte antigen (HLA) signatures between ICI-induced isolated adrenocorticotropic hormone deficiency (IAD) and idiopathic IAD (IIAD). DESIGN AND METHODS: Clinical features and HLA frequencies were compared among 13 patients with ICI-induced IAD, 8 patients with IIAD, and healthy controls. HLA frequencies of healthy controls were adopted from a HLA database of Japanese population. RESULTS: Age and body mass index were higher, while the rate of weight loss was lower, in patients with ICI-induced IAD than in those with IIAD. No HLA alleles had a significantly higher frequency in patients with ICI-induced IAD than in healthy controls, whereas the frequencies of HLA-DRB1*09:01, HLA-DQA1*03:02, and DQB1*03:03 were significantly higher in patients with IIAD than in healthy controls. CONCLUSIONS: ICI-induced IAD and IIAD were different in terms of HLA frequencies. There were no specific HLAs related to ICI-induced IAD, whereas several HLAs in strong linkage disequilibrium were associated with IIAD. This might suggest that the two diseases have different pathological mechanisms. HLAs unique to IIAD may be helpful in predicting its pathophysiology.

A Reliable Surgical Procedure for Sinus Floor Augmentation with Antral Pseudocysts.

An antral pseudocyst (AP) is a common well-defined 'dome-shaped' faintly radiopaque lesion of the maxillary sinus, and usually does not require treatment in asymptomatic patients. However, when sinus floor augmentation is required to increase bone volume for implant installation, the elevation of the sinus mucosa might drive the AP against the ostium. This might cause its obstruction and, as possible consequence, sinusitis. The purpose of this study was to investigate the clinical and tomographic conditions of APs to identify a predictable cyst removal that might allow a safety sinus floor augmentation. A total of 52 maxillary sinuses in 46 patients (mean age 55.1 years) presenting AP were examined by cone beam computed tomographies (CBCTs). A two-stage approach was applied. At the first surgery, the cystic lesions were further inspected by an endoscope through the antrostomy, and histopathological diagnosis of the removed tissues was carried out. After the confirmation of decrease of the swelling of sinus membrane by CBCT, the sinus floor augmentation was performed, at least four months after cyst removal. The color and transparency of the 86 cystic lesions were classified into 4 types. The whitish transparent cysts were 34 (39.5%), the yellowish transparent cysts were 18 (20.9%), the dark purple transparent cysts were 8 (9.3%) and the milky-white opaque cysts were 26 (30.2%). The contents of the 60 (69.8%) transparent cysts were serous fluid, but those of milky-white cysts were composed of viscous or elastic soft tissues, and the aspiration of the contents was unsuccessful. The analysis of the preoperative CBCT did not provide certainty on the contents of the cystic lesions. All cystic lesions were diagnosed as AP, and an infection was identified in one AP, presenting marked infiltration of the inflammatory cells. Considering the difficulties of performing a correct diagnosis of the AP content by a CBCT analysis, the risk of failure of the surgery that creates severe afflictions to the patients, and the necessity of a histological evaluation of the cyst, a two-stage surgery appeared to be the most reliable procedure.

Influence of Anatomical Parameters on the Dimensions of the Subantral Space and Sinus Mucosa Thickening after Sinus Floor Elevation. A Retrospective Cone Beam Computed Tomography Study.

BACKGROUND: Various anatomical parameters might influence the surgical approach for maxillary sinus floor elevation. The objective of the present study was to retrospectively evaluate the influence of anatomical parameters on the dimensions of the subantral space and of the sinus mucosa thickening after sinus floor elevation. MATERIAL AND METHODS: Seventy-eight maxillary sinuses in sixty-five patients were evaluated on cone beam computed tomographies taken before surgery and after one week (t1w) and nine months (t9m). Several parameters such as the distance XF between an axis parallel to the base of the nose (X-axes) and the sinus floor (F) were correlated with the height gain (IF) at t1w and t9m and the post-surgical edema. RESULTS: A weak significant positive correlation was observed between height gain vs. sinus height of interest (XF), the balcony, and the sinus floor angle. The post-surgical edema was influenced by the initial mucosa thickness and the xenograft used. CONCLUSIONS: Various parameters might affect height gain and sinus mucosa thickening after sinus floor elevation. The height of interest, the balcony, and the sinus floor angle showed significant correlations with height gain. The initial thickness of the mucosa and the biomaterial used influenced the post-surgical edema.

A comparison on the percentage of polymerase chain reaction positivity for SARS-CoV-2 between Public Health Center referrals and direct walk-in patients: A single center retrospective analysis in Tokyo.

INTRODUCTION: The Public Health Center (PHC)-known as hokenjo in Japan-assume a crucial role in disease control. Coronavirus disease 2019 (COVID-19) is one of many designated infectious diseases monitored by the agency. During the present pandemic, patients who suspected COVID-19 were instructed to call the Coronavirus Consultation Center in the PHC prior to visiting the hospital. The aim of this study was to elucidate the differences in polymerase chain reaction (PCR) positivity between PHC referrals and direct walk-in patients. METHODS: The present was a single-center, retrospective cohort study conducted at the Tokyo Metropolitan Hospital from March to September, 2020. Patients who received a PCR test for SARS-CoV-2 were included and categorized into the PHC referral or direct walk-in groups. The outcomes included the total number of patients undergoing PCR tests and the percentage of PCR positivity in each group. RESULTS: We identified 1680 patients (781 PHC referred and 899 direct walk-in groups). The percentage of PCR positivity did not significantly differ between the PHC referral and direct walk-in groups during the first wave (30.5% vs. 29.2%; p = 0.78). PCR positivity was significantly higher in the PHC referral group than the direct walk-in group during the second wave (30.1% vs. 23.1%; p = 0.051) and entire study period (30.2% vs. 24.7%; p = 0.011). CONCLUSIONS: Despite health authority recommendations, the number of direct walk-in patients were higher than PHC referral patients. The percentage of PCR positivity was significantly higher in the PHC referral group than in the direct walk-in group.

An enigmatic soft tissue creeping phenomenon: The spontaneous peri-implant mucosa margin and papilla growth. A retrospective clinical study.

OBJECTIVES: The aim of the present retrospective study was to evaluate papillae filling rate and buccal margins coronal growth in implant-supported prostheses which were over-contoured at the apical buccal third to form a rearmost collar zone, thus mimicking a false root. MATERIAL AND METHODS: The influence of adjacent elements, teeth, implants, or pontics was examined. One-hundred and three crowns have been assessed in photographs taken on 61 patients after prosthesis delivering and at last follow-up (mean 2.8 years). The Jemt index was adopted to evaluate papillae growth at the baseline and follow-up as follows: 0, absence of papilla; 1, less than half of interdental embrasure height; 2, more than half of interdental embrasure height; 3, fully papilla filled interdental embrasure. Index score 4, papilla hyperplasia was not included. Moreover, the coronal growth (or recession) of buccal mucosa in implant-supported crowns was assessed. RESULTS: At baseline, a total of 29 papillae had a 0 score, while only two scored 3 with complete papilla formation. On follow-up, only one papilla scored 0, while 46 scored 3 with complete interdental embrasures filling. The highest papilla score was registered from first year crown insertion and likewise in interdental embrasures located between two implants or implants and pontics. Moreover, the buccal margin growth was observed in almost 80% of crowns. Such findings seem to indicate that buccal margin and papilla around implant-supported crowns presented a coronal growth over time, especially during its first year. The average papilla growth between two implants was no lower than that observed in papilla present between implants and natural teeth. CONCLUSIONS: Recessed areas at collar of implant-supported prostheses appear to positively influence papillae and buccal margin growth, especially in its first year. Papilla growth between two implants was similar to that observed between implants and natural teeth.

Surface bio-functionalization using plasma of argon could alter microbiological and topographic surface analysis of dental implants?

BACKGROUND: Plasma of argon was demonstrated to improve protein and cell adhesion on implant surface. On the other hand, increased surface energy and hydrophilicity could potentially amplify the risks of implant surface contamination during clinical phases, risks that have not yet been evaluated in Literature. The aim of the present in vitro study was to verify if Plasma treatment could alter the implant surface characteristics and its ability to remain sterile. MATERIALS AND METHODS: Implants from 9 brands were collected (n=11). One implant for each company was used for SEM surface analysis. To perform the microbiological analysis, ten implants from each company were used and randomly split by allocation either in test or control group. To replicate the surgical work flow, both test and control samples were left 60s in clinical environment. Bacterial growth analysis was performed. Optical density at 600nm was measured as readout of bacterial growth and colony forming unit (CFU) after 24h was evaluated. Statistical analysis was performed by using the Wilcoxon Mann Whitney test. A p-value lower than 0.05 was considered significant. RESULTS: SEM analysis revealed different categories of implant surface roughness. The optical density confirmed a readout of bacterial growth between 4 and 7 with no significant differences within groups. The number of CFU/ml for each measured sample (test and control) was lower than 102 and failed to present significant differences. CONCLUSION: Surface activation using plasma of argon did not affect the degree of implant contamination, allowing to maintain a substantial sterility of the implant independently of its morphology. This may allow in the next future the use of bioactivation through plasma of argon to exploit the superhydrophilicity deriving from this biophysical process.

Anatomical analyses for maxillary sinus floor augmentation with a lateral approach: A cone beam computed tomography study.

BACKGROUND: Various anatomical references and structures should be analyzed prior approaching a surgery in the maxillary sinus. The objective of the present study was to evaluate the anatomical structures and references involved in sinus floor elevation with a lateral approach. MATERIALS AND METHODS: Seventy-five patients planned for sinus floor elevation were included in the study. Eighty-eight maxillary sinuses were evaluated using cone beam computed tomographies (CBCTs). The nasal floor was used as main reference (X) and sinus mucosa width, bone crest height, palatal-nasal recess angle (PNR), sinus width at the level of the nasal floor, distance from the nasal floor to the base of the sinus (X-F), position of the posterior superior alveolar artery (PSAA height) and diameter (PSAA diameter), lateral bone wall width at 3mm (LW 3mm) and 9mm (LW 9mm) from the base of the sinus (F), patency of the ostium (OP), and presence and position of septa have been evaluated. RESULTS: The mean dimensions and standard deviations were the following: mucosa thickness was 2.0±1.4mm, bone crest height 2.8±1.4mm, distance X-F 8.3±1.9mm, PNR angle 135.5±23.1, sinus width 12.6±4.2mm, X-F 8.3±1.9mm, PSAA height 14.4±2.9mm, PSAA diameter 1.1±0.4mm, LW 3mm 1.5±1.2, LW 9mm 1.3±0.6mm, OP 1.9±0.4mm. Septa were present in 19.3% of the sinuses evaluated and were located mostly in the molar region. CONCLUSIONS: In conclusion, the analysis of the CBCT before sinus floor elevation allows the identification of anatomical structures and references that might be used for the planning of the surgical approach, aiming to improve the outcome of the treatment and to avoid possible complications.

Biological and technical complications of tilted implants in comparison with straight implants supporting fixed dental prostheses. A systematic review and meta-analysis.

OBJECTIVES: To evaluate the implant failure, marginal bone loss (MBL), and other biological or technical complications of restorations supported by tilted and straight implants after at least 3 years in function. METHODS: Electronic and manual searches were performed in MEDLINE, Embase, Web of Science, and OpenGrey to identify clinical studies published up to December 2017. After duplicate study selection and data extraction, the risk of bias was assessed with the ROBINS-I tool. Random-effects meta-analyses of relative risks (RRs) or mean differences (MD) and their 95% confidence intervals (CIs) were performed, followed by subgroup/sensitivity analyses and application of the GRADE approach. RESULTS: A total of 17 nonrandomized studies (eight prospective/nine retrospective) were included. The number of implants of the overall systematic review was 7,568 implants placed in 1,849 patients supporting either full-arch or partial implant prostheses. No difference in the failure of tilted and straight implants was seen (eight studies; 4,436 implants; RR = 0.95; 95% CI = 0.70 to 1.28; p = 0.74), with the quality of evidence being very low due to bias and imprecision. Likewise, no difference in MBL was seen between tilted and straight implants (16 studies; 5,293 implants; MD = 0.03 mm; 95% CI = -0.03 to 0.10 mm; p = 0.32), with the quality of evidence being very low due to bias and inconsistency. Contradictory results regarding implant survival were found from prospective and retrospective studies, which could indicate bias from the latter. CONCLUSIONS: Within the limitations of the present systematic review, no effect of implant inclination on implant survival or peri-implant bone loss was found.

Circumstances of La, Eu, Dy, and Yb Cations Intercalated via Ion Exchange in γ-Zirconium Phosphate.

Both α- and γ-zirconium phosphate were examined for use as ion exchangers for recovery of rare earth elements. Trivalent rare earth elements can be partially substituted for protons in the interlayer space, and γ-zirconium phosphate shows a much better ion exchange competency than α-zirconium phosphate. The exchanged cation of the rare earth elements might be related to different amounts of oxygen from P-OH and H2O, and these rare earth elements were thus positioned at a different separations from the zirconium phosphate layer. The radial structure function (RSF) curve from extended X-ray absorption fine structure data implied that the calibrated M-O distance and coordination number changed with the ionic radius. The calibrated M-O distances from RSF were 2.52, 2.42, 2.38, and 2.28 for La, Eu, Dy, and Yb, respectively. The coordination numbers of oxygen for Yb were approximately 7 and greater than 10 for La and Eu, respectively. These smaller coordination numbers for smaller cations may result from the strong interaction between the cations and the zirconium phosphate layer. The Debye-Waller factor also increased with an increase in the ionic radius. These factors show a strong relation to the coordination state of rare earth elements in the unit cell of the γ-zirconium phosphate and to the interaction strength.

Influence of the Buccal Bone Crest Width on Peri-Implant Hard and Soft Tissues Dimensions: A Histomorphometric Study in Humans.

OBJECTIVE: To histologically evaluate hard and soft tissues adaptation at screw-shaped devices installed at recipient sites in the distal segments of the alveolar edentulous ridge prepared with a buccal bone width of 1 or 2 mm. MATERIAL AND METHODS: Sixteen volunteers received 2 nonsubmerged titanium implants each; after 3 months, biopsies were obtained and processed for histology. The distances between implant shoulder (IS), top of the bony crest (C), coronal level of osseointegration (B), peri-implant mucosa (PM), and apical extension of the junctional epithelium (aJE) were measured. RESULTS: There were no significant statistically differences between test and control sites regarding IS-C, IS-B, PM-IS, PM-B, PM-aJE, aJE-B measurements. The horizontal bone resorption 1 mm below IS was 0.3 ± 0.3 and 1.0 ± 0.7 mm at the test and control sites, respectively. This difference was statistically significant. CONCLUSIONS: Similar hard and soft tissues dimensions were observed in both groups. However, a higher horizontal bone resorption was seen at the control sites. Nonsubmerged implant installation should be performed when a 1 mm buccal bony crest width is present so as to limit the horizontal bone resorption.