Evaluation of image lag in a flat-panel, detector-equipped cardiovascular X-ray machine using a newly developed dynamic phantom.

We developed a dynamic phantom for use in routine checks. This phantom can be used to physically evaluate image lag that occurs in dynamic images. It has a unique measurement method. ROIs on the target are chosen, and, with the position of ROIs fixed on the image, changes in pixel value are detected physically when the target passes through the ROIs over time and perceived as image lag. Thus, it was possible to physically detect different intensities of image lag lasting less than one second while maintaining the same intensity trends. The checking technique we propose with the dynamic phantom that we developed could be effective for routine checking of fluoroscopy X-ray machines, and could become an established method.

Validation of a Metal Artifact Reduction Algorithm Using 1D Linear Interpolation for Cone Beam CT after Endovascular Coiling Therapy for Cerebral Aneurysms.

This study aimed to evaluate the effect of a metal artifact reduction (MAR) algorithm using 1D linear interpolation on cone-beam CT (CBCT). We performed phantom and clinical qualitative studies with and without MAR application using 1D linear interpolation. In the phantom study, the standard deviation (SD) was estimated from the images obtained from the water phantom in which a metal coil was placed at the center, and observed the changes in the SDs before and after MAR application. In the clinical qualitative study, the clinical images after endovascular treatment (EVT) for cerebral aneurysms were visually evaluated before and after MAR application. In the phantom study, the SDs after MAR application decreased by 56 to 35% compared with that before MAR application. In the clinical qualitative study, the artifacts from the metal coil decreased or increased depending on locations, and the contrasts of gray matter and white matter were attenuated when MAR was applied. In conclusion, the metal artifact decreases when MAR using 1D linear interpolation is applied to cerebral CBCT. However, another artifacts increase or soft tissue contrast is changed in some cases. MAR largely contributes to the reduction of streaking artifacts, whereas it may induce cerebral parenchyma at distant metal body or quality deterioration of the image not including the metal body. This should be taken into account in the diagnosis of secondary hemorrhage or infarction.

[Usefulness of virtual vessel images in ppi for treatment of complete obstruction of leg arteries].

Following recent rapid advances in devices and treatment technology, indications for percutaneous peripheral intervention (PPI) have been expanded to include complex lesions (long-segment lesions, completely obstructed chronic lesions, etc.) and even lesions of the superficial femoral artery and arteries distal to the popliteal artery. However, when PPI is used for treatment of complete obstruction, treatment can take a long time or its outcome can be less satisfactory for reasons such as difficulty in assessing the vascular distribution/arrangement or the direction of calcification in the obstructed area or excessively long lesions. In the present study, we conducted three-dimensional image processing of CT data from leg arteries conventionally used for preoperative diagnosis. Using this processing technique, we created virtual images of the blood vessels of the completely obstructed area and mapped these virtual vessel images onto the fluoroscopic monitor image during catheter treatment. The usefulness of this technique for PPI was then evaluated. We succeeded in creating virtual vessel images of the completely obstructed parts of leg arteries with the use of preoperative CT images of leg arteries that we then mapped onto the fluoroscopic monitor images during treatment. We were successful in mapping virtual images onto the abdominal aorta in 96.8% of cases and in 95.7% with the common iliac artery. This technique is thus able to supply reliable information on vascular distribution/arrangement, suggesting that it can enable the surgeon to advance the treatment device precisely along the vessels, making it useful for treatment with PPI. The study additionally showed that differences in the angle of imaging affect the manual mapping of the CT images onto angiograms.

[Study of heart region of interest setting method in the hepatic functional reserve index of (99m)tc-diethylenetriamine pentaacetic Acid-galactosyl human serum albumin].

In this study we analyzed the influence of region of interest (ROI) selection on the uptake ratio of the liver to the liver plus heart at 15 min (LHL15) during (99m)Tc-galactosyl human serum albumin (GSA) scintigraphy and determined the optimal ROI by evaluating the individual effects of different ROIs in the heart on LHL15. Twenty patients were randomly selected from those who had undergone (99m)Tc-GSA scintigraphy GSA between April 2008 and June 2009. The liver body (L/B) ratio, liver uptake 15 min (LU15), and LHL15 were analyzed and compared among the following ROIs: entire heart, both ventricles, right ventricle, and left ventricle. There were significant differences in the L/B ratio and LU15 values among the different ROIs. However, LHL15 showed a tendency to shift toward a normal value when the size of the ROI was small (only the right or left ventricle), resulting in a lack of distinction between normal and abnormal LHL15 values. Furthermore, setting the entire heart as the ROI was difficult and reproducibility was low. Our results suggest that the use of both ventricles as the ROI provides optimal LHL15 values during (99m)Tc-GSA scintigraphy.

[Examination of the shoulder joint using true anterior-posterior photography, employing a body surface index].

Radiographic examination of the anterior part of the shoulder includes routine anterior-posterior imaging that enables easy visualization of traumatic injuries and true anterior-posterior imaging that enables the visualization of intra-articular injuries. The X-ray incident angle of true anterior-posterior imaging is affected by physique and posture. However, in many reports, the angle is uniformly determined on the basis of the antero-posterior axis and the horizontal plane. We previously reported that the glenohumeral joint can be visualized with good reproducibility by establishing a reference line on the basis of three points on the body as indicators, namely the posterior view of the under-surface of the acromion, the coracoid process, and the inferior angle of the scapula. However, visualizing the undersurface of the acromion using physical indicators to set the angle for imaging remains problematic. In previous reports, the angle was consistently set at 20° to the horizontal plane, regardless of physique or posture, which resulted in poor reproducibility. After examining the imaging techniques described in previous reports, we describe here an imaging technique using a reference line based on indicators on the surface of the scapula that enables the glenohumeral joint and the undersurface of the acromion to be visualized with good reproducibility.

[A review of the position adopted by patients when acquiring images of the base of the hamate hook].

The hamate bone, one of the carpal (wrist) bones, has a large uncinate process protruding from the palm side. In sports such as golf and tennis, the hamate bone can break if is subjected to a high external force, such as from the handle of a racquet or club. At our hospital we take X-ray images of the hamate bone from two directions: an axial image through the carpal tunnel and an image at the base of the hamate hook (conventional method). While the conventional method makes it easy to create images of the base of the hamate hook, the patient may suffer pain during image-taking because the hamate bone is pulled to cause radial flexion. We therefore investigated a method of imaging that would create three-dimensional computed tomography (3DCT) images of the base of the hamate hook in which the patient would only have to only rotate the wrist externally and elevate the fore-arm without any radial flexion. Our results suggest that it is possible to obtain images of the base of the hamate hook as clear as those acquired using the conventional method with the patient in a comfortable and painless position taking images at an external rotation angle of 50.3° and a forearm elevation angle of 20.3°.

[Failure analysis of medical linear accelerator with reliability analyses].

We analyzed a number of cases about the Linac troubles in our hospital and have examined the effect of preventive maintenance with Weibull analysis and exponential distribution from April 2001 to March 2012. The total failure by irradiation disabled was 1, 192. (1) Medical linear accelerator (MLC) system was 24.0%, (2) radiation dosimetry system 13.1%, and the (3) cooling-water system was 26.5%. It accounts for 63.6% of the total number of failures. Each parameter value m, which means the shape parameter, and the failure period expectancy of parts µ were (1) 1.21, 1.46/3.9, 3.8 years. 3.7, 3.6 years. (2) 2.84, 1.59/6.6, 4.3 years. 6.7, 5.9 years. (3) 5.12, 4.16/6.1, 8.5 years. 6.1, 8.5 years. Each shape parameter was m>1. It is believed that they are in the worn-out failure period. To prevent failure, MLC performance should be overhauled once every 3 years and a cooling unit should be overhauled once every 7 years. Preventive maintenance is useful in assessing the failure of radiation therapy equipment. In a radiation dosimetry part, you can make a preemptive move before the failure by changing the monitor's dosimeter board with a new part from the repairs stockpiled every 6 months for maintenance.

[Proposal for an auxiliary tool designed to reduce retake rates for lateral radiography of the knee joint].

The reproducibility of lateral radiography of the knee joint in the lateral position is low because patient positioning can be easily affected by passive rotation of the knee joint. We calculated the correction angle of the femoral external rotation and the lower leg elevation and developed our own auxiliary tool for obtaining a lateral view image. We were able to obtain, in a single attempt, an image with misalignment of the condyle limited to less than 7 mm. Our tool also contributed to the reduction of the re-imaging rate, suggesting its usefulness in contributing to a lower re-imaging rate for lateral radiography of the knee joint.

[Effect of Kiken-Yochi training (KYT) induction on patient safety at the department of radiological technology].

PURPOSE: In this report, we evaluated whether radiological technologists' (RTs') awareness of patient safety would improve and what kind of effects would be seen at the department of radiological technology by introducing KYT [K: kiken (hazard), Y: yochi (prediction), T: (training)]. METHODS: KYT was carried out by ten RTs based on a KYT sheet for the department of radiological technology. To evaluate the effects of KYT, we asked nine questions each to ten participants before and after KYT enforcement with regard to their attitude to patient safety and to operating procedures for working safely. RESULTS: Significant improvements after KYT enforcement were obtained in two items concerning medical safety: It is important for any risk to be considered by more than one person; The interest in preventive measures against medical accident degree conducted now) and one concerning operating procedures (It is necessary to have a nurse assist during testing with the mobile X-ray apparatus) (p<0.05). CONCLUSIONS: Performing KYT resulted in improved awareness of the importance of patient safety. KYT also enabled medical staffers to evaluate objectively whether the medical safety measures currently performed would be effective for patients.

[Observations of deterioration of photo-stimulable phosphor plates used in digital mammography and its effects on mammography diagnoses].

We noted that breast-like artifacts occur in photo-stimulable phosphor plates (PSPs) used for long periods in digital mammography systems. This prompted us to investigate the effects on mammography diagnoses of these artifacts. Our study took the form of a comparison between the images generated by a long-term use PSP (four years use) and a short-term use PSP. First, an acrylic phantom and an in-house-made phantom for visual evaluation were imaged using X-ray PSPs under the same exposure conditions. They were then scanned under the same conditions to generate images. The mean values of the digital signals were measured in the 35 locations of region of interest present in the images of the acrylic phantom. The images of the in-house-made phantom were then visually evaluated by five certified experts, who examined 22 clinical images taken with both PSPs while referring to a visual evaluation scale. Differences were detected in all the evaluated items: the short-term use PSP gave a higher rate than the long-term use PSP (p<0.01), suggesting that long-term use PSPs might adversely affect the results of diagnostic mammography.

[Clinical study to obtain true view of the glenohumeral joint on scapula-45].

Scapula-45 is an original roentogenographical technique to clarify objectively the function of the rotator cuff and scapulothoracic joint. This examination enables assessment of the function of the rotator cuff and scapulothoracic joint utilizing the radiographs of the glenohumeral joint. However, in the former technique, it was difficult for the technician to properly align the patient for the view of the true glenohumeral joint because of the individual postural difference of the patients, such as kyphosis. In the present study, we reported a new technique with the use of the acromion, coracoid process, and inferior angle of the scapula as a landmark to obtain the consistent radiographs of the glenohumeral joint.

[Development of image quality assurance support system using image recognition technology in radiography in lacked images of chest and abdomen].

In order to provide a precise radiography for diagnosis, it is required that we avoid radiography with defects by having enough evaluation. Conventionally, evaluation was performed only by observation of a radiological technologist (RT). The evaluation support system was developed for providing a high quality assurance without depending on RT observation only. The evaluation support system, called as the Image Quality Assurance Support System (IQASS), is characterized in that "image recognition technology" for the purpose of diagnostic radiography of chest and abdomen areas. The technique of the system used in this study. Of the 259 samples of posterior-anterior (AP) chest, lateral chest, and upright abdominal x-rays, the sensitivity and specificity was 93.1% and 91.8% in the chest AP, 93.3% and 93.6% in the chest lateral, and 95.0% and 93.8% in the upright abdominal x-rays. In the light of these results, it is suggested that AIQAS could be applied to practical usage for the RT.

[Examination of patient dose reduction in cardiovasucular X-ray systems with a metal filter].

In interventional X-ray for cardiology of flat panel digital detector (FPD), the phenomenon that exposure dose was suddenly increased when a subject thickness was thickened was recognized. At that time, variable metal built-in filters in FPD were all off. Therefore, we examined whether dose reduction was possible without affecting a clinical image using metal filter (filter) which we have been conventionally using for dose reduction. About 45% dose reduction was achieved when we measured an exposure dose at 30 cm of acrylic thickness in the presence of a filter. In addition, we measured signal to noise ratio/contrast to noise ratio/a resolution limit by the visual evaluation, and there was no influence by filter usage. In the clinical examination, visual evaluation of image quality of coronary angiography (40 cases) using a 5-point evaluation scale by a physician was performed. As a result, filter usage did not influence the image quality (p=NS). Therefore, reduction of sudden increase of exposure dose was achieved without influencing an image quality by adding filter to FPD.

[Effect of changing into slippers on the pollution situation in the nuclear medicine management district].

Changing into slippers when entering the nuclear medicine management district prevented pollution expansion. Accidents involving patients falling occurred in university facilities. It was thought that changing slippers was the cause. The pollution situation was measured in three facilities by using the smear method and the direct technique to examine the effect of changing slippers. The current state was measured. After pollution prevention guidance was continuously done, pollution expansion was measured; three weeks of measurements were compared. Pollution was detected in the first period of weeks at a frequency of 19 times. For the latter period, it was detected 6 times. Half the pollution was in the restroom. Pollution was reduced by doing pollution prevention guidance for the restroom. Patients' falls occur even if they change slippers. Falling accidents can be decreased.

[Evaluation of crossing calibration of (123)I-MIBG H/M ration, with the IDW scatter correction method, on different gamma camera systems].

(123)I-MIBG Heart-to-Mediastinum activity ratio (H/M) is commonly used as an indicator of relative myocardial (123)I-MIBG uptake. H/M ratios reflect myocardial sympathetic nerve function, therefore it is a useful parameter to assess regional myocardial sympathetic denervation in various cardiac diseases. However, H/M ratio values differ by site, gamma camera system, position and size of region of interest (ROI), and collimator. In addition to these factors, 529 keV scatter component may also affect (123)I-MIBG H/M ratio. In this study, we examined whether the H/M ratio shows correlation between two different gamma camera systems and that sought for H/M ratio calculation formula. Moreover, we assessed the feasibility of (123)I Dual Window (IDW) method, which is a scatter correction method, and compared H/M ratios with and without IDW method. H/M ratio displayed a good correlation between two gamma camera systems. Additionally, we were able to create a new H/M calculation formula. These results indicated that the IDW method is a useful scatter correction method for calculating (123)I-MIBG H/M ratios.

[Hand hygiene during mobile X-ray imaging in the emergency room].

A hand hygiene behavior questionnaire and environmental survey were conducted regarding the mobile X-ray system used in the emergency room. As a result, among a total of 22 radiological technologists at this hospital who replied to the questionnaire, 18 wore disposable gloves when performing X-ray imaging using the mobile system. Among those 18, 11 were found to touch computed radiology (CR) consoles and HIS/RIS terminals while still wearing the gloves, thus creating the potential for spreading pathogens to other medical equipment and systems. According to the results of an environmental survey of the emergency imaging preparation room, the highest levels of bacteria were detected on CR consoles and HIS/RIS terminals. A possible reason for this is that these locations are not wiped down and cleaned as a part of routine cleaning and disinfection protocols, thus demonstrating the importance of cleaning and disinfection. Hand hygiene by medical personnel and appropriate cleaning and disinfecting of the working environment are important for preventing the spread of nosocomial infections. Radiological technologists are also required to take effective measures against infections in consideration of the high frequency of contact with both infected patients and patients susceptible to infections.

[Development of software for estimating exposure dose and radiation exposure region in cardiac catheterization inspection].

We developed software for estimating exposure doses and radiation exposure regions in cardiac catheterization inspection. In the software, the back of a thoracic phantom were divided into a total of 21 square blocks with a width of 30 degrees. Furthermore, we developed a system with which reference air kerma is distributed to each of the above blocks in accordance with the distribution ratio calculated from the data obtained by the system, and the calculation results are displayed. Coronary angiography was performed using thoracic phantoms, and actual measurements were obtained using a fluoroglass dosimeter. The calculated results obtained using the software were compared to the measured results. An almost identical tendency was seen, and the radiation regions of the top three estimated exposure doses were successfully estimated. Radiation region estimation using this software is affected by exposure time as one of its properties. This software enables estimating radiation exposure regions and exposure doses.

[Study of a new axial projection of shoulder joint without abduction of upper extremity].

A study of a method of taking X-rays of the shoulder joint axis when the upper arm is fixed and cannot be rotated. When the shoulder joint has suffered damage, rotating the arm can be very painful, and obtaining accurate images of the axis is frequently difficult. For this reason, at this hospital, the Stockinette-Velpeau procedure is used on patients who cannot rotate their arms to have X-rays taken. In this procedure, the patient bends backwards at a 40-degree angle, and an X-ray of the shoulder joint axis is taken from directly below the joint. Using this method, even if the upper arm is hanging down, information regarding the direction of the axis can be obtained. However, maintaining this body position is difficult and requires assistance. The patient may also experience pain. For this reason, a new method was sought of X-raying the axis from a body position that is easier on the patient and by which diagnostic information on the axis direction can be obtained from patients who cannot rotate their upper arms. The result of seeking a new method was an X-ray that can be taken diagonally at a 25-degree angle relative to the shoulder joint socket. This X-ray method requires no rotation of the axis and provides the closest view of the axis. This new method suggests a way to X-ray the axis that is easy on patients even when the shoulder joint is damaged.

Overlap of radiation field and radiation field shape in cardiac catheterization.

The radiation field shape for cardiac catheterization has changed from being circular to being rectangular with the spread of flat-panel detector systems. A rectangular radiation field provides a wide fluoroscopy field to the four corners of a subject area; however, in cardiac catheterization, there is not much usable information around the four corners at several angles, and this tends to be regarded as a meaningless radiation exposure. Hence, overlap of radiation fields has been of concern recently. The authors changed field sizes/fluoroscopy angles and examined entrance dose rates to study radiation field shapes and configurations of radiation exposure to patients, and they discussed a radiation exposure reduction method. In measurements of phantom entrance dose rates, we considered right anterior oblique (RAO) directions, cranial (CRA) directions and RAO-CRA directions and found that entrance dose rates rose considerably, particularly at the RAO-CRA. In the study of radiation field overlap, we discuss radiation field shapes (rectangular/circular) as well as angles. In the RAO-CRA directions, differences occurred in angles of non-overlapping radiation field by differences in radiation field shapes. For RAO-CRA, compared with the RAO and CRA directions, entrance dose rates increased with an increase in angle. When convenience in clinics is considered, the utilization frequency of the four corners of a rectangular field is low. When one considers the increases in radiation exposure caused by radiation field overlap, it is more effective to use circular radiation fields.

[Examination of safety improvement by failure record analysis that uses reliability engineering].

How the maintenance checks of the medical treatment system, including start of work check and the ending check, was effective for preventive maintenance and the safety improvement was verified. In this research, date on the failure of devices in multiple facilities was collected, and the data of the trouble repair record was analyzed by the technique of reliability engineering. An analysis of data on the system (8 general systems, 6 Angio systems, 11 CT systems, 8 MRI systems, 8 RI systems, and the radiation therapy system 9) used in eight hospitals was performed. The data collection period assumed nine months from April to December 2008. Seven items were analyzed. (1) Mean time between failures (MTBF) (2) Mean time to repair (MTTR) (3) Mean down time (MDT) (4) Number found by check in morning (5) Failure generation time according to modality. The classification of the breakdowns per device, the incidence, and the tendency could be understood by introducing reliability engineering. Analysis, evaluation, and feedback on the failure generation history are useful to keep downtime to a minimum and to ensure safety.