Crystal Structures and Conduction Paths of Sc-Doped CaTiO3 Fast Oxide-Ion Conductors with Orthorhombic Symmetry.

The crystal structures and electron density distributions (EDDs) of Ca-deficient Sc-doped CaTiO3 fast oxide-ion conductors, Ca0.97(Ti0.97Sc0.03)O3-δ (CTS3) and Ca0.96(Ti0.9Sc0.1)O3-δ (CTS10), were investigated in the temperature range of 298-1173 K in N2 to analyze the effect of composition on the perovskite structure and oxide-ion transport mechanism. CTS3 and CTS10 exhibited orthorhombic Pnma symmetry in temperature ranges of 298-1173 K and 973-1173 K, respectively, with CTS10 exhibiting lower symmetry and reduction in oxide-ion conductivity below 973 K. The EDDs of CTS3 and CTS10 at 1173 K indicated unique chemical bonds and conduction paths. CTS3 and CTS10 showed covalent bonds between (Ti,Sc) and O1 (or O2) sites. CTS3, with a lower oxide-ion conductivity than that of CTS10, exhibited pseudo-one-dimensional (1D) zig-zag curved conduction paths for oxide-ions along the a-axis, unlike previously reported curved migration paths along the b-axis in CaTiO3, and chemical bonds between Ca and O1 sites, indicating oxide-ion conduction suppression. In CTS10, additional conduction paths were observed along the a-axis, forming three-dimensional (3D) zig-zag curved conduction paths in the ac-plane and along the b-axis, with the weakening of the chemical bonds between the Ca and O1 sites. The oxide-ion conductivity and mobile oxide-ion concentration of CTS10 were 3.6 and 2.0 times those of CTS3, respectively, at 1173 K; the higher oxide-ion conductivity of CTS10 could be attributed to an increase in the mobile oxide-ion concentration and mobility with a 1D to 3D change in the conduction paths and a weakening of chemical bonds between the Ca and O1 sites.

Effect of Aspect Ratio on the Permittivity of Graphite Fiber in Microwave Heating.

Microwave (MW) heating has received attention as a new heating source for various industrial processes. Some materials are expected to be a more effective absorber of MW, and graphite is observed as a possible candidate for high-temperature application. We investigated the dependence of the aspect ratio of graphite fibers on both their heating behavior and permittivity under a 2.45 GHz MW electric field. In these experiments, both loss tangent and MW heating behavior indicated that the MW absorption of conductive fibers increases with their aspect ratio. The MW absorption was found to be well accounted for by the application of a spheroidal model for a single fiber. The absorption of graphite fibers decreases with increasing aspect ratio when the long axis of the ellipsoid is perpendicular to the electric field, whereas it increases with the aspect ratio when the long axis is parallel to the electric field. The analytical model indicated that MW heating of the conductive fibers is expected to depend on both the shape and arrangement of the fibers in the electric field.

Absorptive removal of biomass tar using water and oily materials.

Water is the most common choice of absorption medium selected in many gasification systems. Because of poor solubility of tar in water, hydrophobic absorbents (diesel fuel, biodiesel fuel, vegetable oil, and engine oil) were studied on their absorption efficiency of biomass tar and compared with water. The results showed that only 31.8% of gravimetric tar was removed by the water scrubber, whereas the highest removal of gravimetric tar was obtained by a vegetable oil scrubber with a removal efficiency of 60.4%. When focusing on light PAH tar removal, the absorption efficiency can be ranked in the following order; diesel fuel>vegetable oil>biodiesel fuel>engine oil>water. On the other hand, an increase in gravimetric tar was observed for diesel fuel and biodiesel fuel scrubbers because of their easy evaporation. Therefore, the vegetable oil is recommended as the best absorbent to be used in gasification systems.

A simple expression for the apparent reaction rate of large wood char gasification with steam.

A simple expression for the apparent reaction rate of large wood char gasification with steam is proposed. Large char samples were gasified under steam atmosphere using a thermo-balance reactor. The apparent reaction rate was expressed as the product of the intrinsic rate and the effective factor. The effective factor was modified to include the effect of change in char diameter and intrinsic reaction rate during the reaction. Assuming uniform conversion ratio throughout a particle, the simplified reaction scheme was divided into three stages. In the initial stage, the local conversion ratio increases without particle shrinkage. In the middle stage, the particle shrinks following the shrinking core model without change in the local conversion ratio. In the final stage, the local conversion ratio increases without particle shrinkage. The validity of the modified effective value was confirmed by comparison with experimental results.

A comparison of co-combustion characteristics of coal with wood and hydrothermally treated municipal solid waste.

In this work, thermogravimetric analysis was used to investigate the co-combustion characteristics of wood and municipal solid waste (MSW) with Indian coal. Combustion characteristics like volatile release, ignition were studied. Wood presented an enhanced reaction rate reflecting its high volatile and low ash contents, while MSW enhanced ignition behavior of Indian coal. The results indicate that blending of both, wood and MSW improves devolatization properties of coal. Significant interaction was detected between wood and Indian coal, and reactivity of coal has improved upon blending with wood. On the other hand, MSW shows a good interaction with Indian coal leading to significant reduction in ignition temperature of coal and this effect was more pronounced with higher blending ratio of MSW. Hence MSW blending could more positively support the combustion of low quality Indian coal as compared to wood, due to its property of enhancement of ignition characteristics.

Effects of the reforming reagents and fuel species on tar reforming reaction.

In this study, using wood chips and polyethylene (PE) as fuels, the effects of air and/or steam as reagents on the tar reforming were clarified quantitatively with a simulated gasifier/reformer apparatus of a two-staged gasification process. The results show that when only steam or air was supplied into the reformer, the tar residual rate (defined as the ratio of the tar amount in the reformed gas to the tar amount in the pyrolysis gas) and the carbon particulate concentration in both reformed gases produced from pyrolysis gases of wood chips and PE decreased with the increase of the steam ratio (H(2)O/C, 0-1.0) or the air ratio (ER, 0-0.30). Supplying steam into the reformer to suppress carbon particulate formation for PE pyrolysis gas is more effective than for wood chips pyrolysis gas. Comparing with the results of steam only reforming, the effect of air supply on reduction of the tar residual rate was more significant, while that on suppression of carbon particulate formation was smaller.