Storage Optimization of Transmission Holographic Gratings in Photohydrogels.

The development and optimization of holographic materials represent a great challenge today. These materials must be synthesized according to the characteristics that are desirable in photonic devices whose application is the object of investigation. In certain holographic sensors and biosensors, it is essential that the recording material be stable in liquid media. Furthermore, the holographic gratings stored in them must have temporal and structural stability, so that they can act as transducers of the analytical signal. Therefore, it is essential to optimize its storage in terms of the chemical composition of the material and the optical parameters of recording. This work focuses on the study of the storage optimization of unslanted transmission volume phase holograms in photohydrogels based on acrylamide and N,N'-methylenebis(acrylamide). Hydrogel matrices, also composed of acrylamide and N,N'-methylenebis(acrylamide), with different degrees of cross-linking were used and analyzed by scanning electron microscopy and UV-visible spectroscopy. The best results in terms of diffraction efficiency were reached for hydrogel matrices with an acrylamide/N,N'-methylenebis(acrylamide) molar ratio between 19.9 and 26. This relationship was also optimized in the incubator solution used to incorporate the components necessary for the formation of the holograms in the hydrogel matrices. The maximum diffraction efficiency, about 35%, was achieved when using an incubation solution with an acrylamide/N,N'-methylenebis(acrylamide) molar ratio of 4.35. The influence of the physical thickness of the hydrogel layers, the intensity, and the exposure time on the diffraction efficiency was also investigated and optimized. In addition, the behavior of the hologram was analyzed after a washing stage with PBST. A simple model that considered the effects of bending and attenuation of holographic gratings was proposed and used to obtain the optical parameters of the holograms.

Holographic Lens Resolution Using the Convolution Theorem.

The similarity between object and image of negative asymmetrical holographic lenses (HLs) stored in a low-toxicity photopolymer has been evaluated theoretically and experimentally. Asymmetrical experimental setups with negative focal lengths have been used to obtain HLs. For this purpose, the resolution of the HLs was calculated using the convolution theorem. A USAF 1951 test was used as an object and the impulse responses of the HLs, which in this case was the amplitude spread function (ASF), were obtained with two different methods: using a CCD sensor and a Hartmann Shack (HS) wavefront sensor. For a negative asymmetrically recorded HL a maximum resolution of 11.31 lp/mm was obtained. It was evaluated at 473 nm wavelength. A theoretical study of object-image similarity had carried out using the MSE (mean squared error) metric to evaluate the experimental results obtained quantitatively.

Adulterant Detection in Peppermint Oil by Means of Holographic Photopolymers Based on Composite Materials with Liquid Crystal.

Diffraction gratings are recorded in a holographic photopolymer containing nematic liquid crystal and peppermint oil. The presence of the oil modifies the polymerization and the holographic response. The composite containing oil adulterated with triethyl citrate obtains a diffraction efficiency related to the oil's purity. The results obtained suggest the possibility of developing a holographic chemical analysis method for quality control of raw materials.

Aberration-Based Quality Metrics in Holographic Lenses.

Aberrations and the image quality of holographic lenses were evaluated by a Hartmann-Shack (HS) wavefront sensor. Two lenses, one recorded with a symmetrical configuration and the other with an asymmetrical one, were stored in a photopolymer called Biophotopol. Each was reconstructed with two different wavelengths, 473 nm and 633 nm. Different metrics were applied to determine and quantify the aberration of the lenses (Zernike coefficients, Seidel coefficients, Marechal tolerances, root-mean-square (RMS), peak to valley, critical fraction of the pupil), and the quality of the image they provided (Strehl ratio, entropy, cutoff frequency, modulation transfer function (MTF), and area under the MTF). Good agreement between the metrics related to optical quality was obtained. The negative asymmetric holographic lenses had less aberration than the positive symmetric ones.

Holographic Lenses in an Environment-Friendly Photopolymer.

In this paper, we theoretically and experimentally evaluated the quality of volume phase transmission lenses stored in an environmentally friendly photopolymer. Holographic lenses (HLs) were obtained using symmetrical and asymmetrical experimental setups with the same positive and negative focal length and pupil diameter. The image quality was evaluated from the calculation of the modulation transfer function (MTF) by capturing the point spread function (PSF) with a charge-coupled device (CCD). A maximum frequency of 14 L/mm, reaching an MTF value of 0.1, was obtained for a negative asymmetrically recorded HL, evaluated at 473 nm wavelength. A theoretical study of aberrations was carried out to qualitatively evaluate the experimental results obtained.

Modeling Diffractive Lenses Recording in Environmentally Friendly Photopolymer.

The improvements made in diffusion models simulating phase image recording in photopolymers enable the optimization of a wide range of complex diffractive optical elements (DOEs), while the miniaturization of spatial light modulators makes it possible to generate both symmetric and non-symmetric DOEs. In addition, there is increasing interest in the design of new friendly recording materials. In this respect, photopolymers are a promising material due to their optical properties. In this paper, we show a procedure to record diffractive spherical lenses using a nontoxic optimized photopolymer. To achieve this goal, we followed three steps: first, the chemical optimization for DOE recording; second, the recording material characterization to be simulated by a three-dimensional diffusion model; and third, the evaluation of the coverplating for the conservation of the DOE.

Additives Type Schiff's Base as Modifiers of the Optical Response in Holographic Polymer-Dispersed Liquid Crystals.

Schiff's bases with specific π-electron system have been synthesized and used as additives in holographic polymer-dispersed liquid crystals. It was observed that these substances modify different parameters such as current intensity, voltage, and diffracted light intensity. In addition, the maximum diffraction efficiency obtained in the reconstruction of the holograms is related to the additive molecule. We propose a relationship between this behavior and the molecular structure of these substances.

Blazed Gratings Recorded in Absorbent Photopolymers.

Phase diffractive optical elements, which have many interesting applications, are usually fabricated using a photoresist. In this paper, they were made using a hybrid optic-digital system and a photopolymer as recording medium. We analyzed the characteristics of the input and recording light and then simulated the generation of blazed gratings with different spatial periods in different types of photopolymers using a diffusion model. Finally, we analyzed the output and diffraction efficiencies of the 0 and 1st order so as to compare the simulated values with those measured experimentally. We evaluated the effects of index matching in a standard PVA/AA photopolymer, and in a variation of Biophotopol, a more biocompatible photopolymer. Diffraction efficiencies near 70%, for a wavelength of 633 nm, were achieved for periods longer than 300 µm in this kind of materials.

Efficient organic distributed feedback lasers with imprinted active films.

We report on the fabrication of efficient organic distributed feedback (DFB) lasers with thermally-nanoimprinted active films, emitting between 565 and 580 nm. The use of thermal-NIL has allowed, as opposed to room temperature or solvent-assisted techniques, high grating quality and excellent modulation depth. The 155°C heat exposure of the NIL process, does not significantly affect the thermal and optical properties of the active material (polystyrene films doped with a perylenediimide derivative). These devices combine a simple and low-cost preparation method with good laser characteristics, i.e. thresholds of 1 µJ/pulse, single-mode emission with linewidths below 0.2 nm and photostability half-lives of ~ 105 pump pulses under ambient conditions. In comparison to more standard DFBs with gratings on the substrate, their fabrication is much easier, while they show a similar laser performance.