Injection Molding Condition Effects on the Mechanical Properties of Coconut-Wood-Powder-Based Polymer Composite.

This study investigates the mechanical properties of coconut sawdust powder combined with polypropylene (PP). The effect of compatibility content, wood powder (WP) content, and injection molding parameters on the properties of coconut wood powder composite (WPC) is evaluated. The results could be used to figure out the optimal mechanical properties such as tensile strength, elongation, elastic modulus, and flexural strength by selecting suitable parameters and composition. The bonding between the WP particles and the PP matrix is good, and the WP is uniformly distributed across the composite matrix, as indicated in the scanning electron microscopy (SEM) results. Interestingly, with the presence of the compatibilizer oleamide, increasing the WP content from 20 wt.% to 40 wt.% did not result in WP accumulation in the composite matrix. Notably, at 20 wt.% WP, the elongation is the highest (at 7.40 wt.%), while at 30 wt.% WP, the elastic modulus reaches the highest value. The maximum ultimate tensile strength (UTS) value is obtained at 35 wt.% WP. Higher WP mostly results in greater flexural strength and shore D hardness. At 40 wt.% WP, the WPC achieves its peak shore D hardness of 77.6. The Taguchi results suggest that WP content is the most critical factor in the UTS value of coconut WPCs. The filling pressure ranks second, followed by the packing pressure. Finally, unlike the other characteristics, the melt temperature has a minimal impact on the UTS value.

Explosive weld joint characteristics of Copper-Tantalum via simulation.

This report aims to examine the effects of impact velocity, impact depth, and impact orientation on the Cu-Ta weld joint of the explosive welding process via MD simulation. The findings indicate that the residual shear stress in the welded block mostly increases as the impact velocity rises. The bottom Ta block is more severely distorted than the higher Cu block due to the impact direction. During the tensile test, three stress zones can be identified including the low-stress Cu block, the high-stress Ta block, and the medium-stress weld joint in the middle of the samples. The weld joint position is lower than the median line of the welded block. The Cu-Ta welded block with 500 m/s impact velocities had the highest ultimate tensile strength (UTS) value of 6.49 GPa. With increasing impact depth, the atomic strain level, residual shear stress, and weld joint dimensions all noticeably increase. The Cu-Ta welded block with an impact depth of 7.5 Å has the greatest UTS values, measuring 11.65 GPa, because of its well-crystal structure. Changing the impact orientation does not result in a dramatic change in atomic strain. Orientation (001) vs (001) has the highest strain and stress rates. With an impact orientation of (110) vs. (111), the Cu-Ta welded block gets the highest UTS value of 8.03 GPa compared to other orientations.

Enhancing Amplification in Compliant Mechanisms: Optimization of Plastic Types and Injection Conditions.

This study surveys the impacts of injection parameters on the deformation rate of the injected flexure hinge made from ABS, PP, and HDPE. The flexure hinges are generated with different filling time, filling pressure, filling speed, packing time, packing pressure, cooling time, and melt temperature. The amplification ratio of the samples between different injection parameters and different plastic types is measured and compared to figure out the optimal one with a high amplification ratio. The results show that the relationship between the input and output data of the ABS, PP, and HDPE flexure hinges at different injection molding parameters is a linear relation. Changing the material or many injection molding parameters of the hinge could lead to a great impact on the hinge's performance. However, changing each parameter does not lead to a sudden change in the input and output values. Each plastic material has different optimal injection parameters and displacement behaviors. With the ABS flexure hinge, the filling pressure case has the greatest amplification ratio of 8.81, while the filling speed case has the lowest value of 4.81. With the optimal injection parameter and the input value of 105 µm, the ABS flexure hinge could create a maximum average output value of 736.6 µm. With the PP flexure hinge, the melt temperature case achieves the greatest amplification ratio of 6.73, while the filling speed case has the lowest value of 4.1. With the optimal injection parameter and the input value of 128 µm, the PP flexure hinge could create a maximum average output value of 964.8 µm. The average amplification ratio values of all injection molding parameters are 6.85, 5.41, and 4.01, corresponding to ABS, PP, and HDPE flexure hinges. Generally, the ABS flexure hinge has the highest amplification ratios, followed by the PP flexure hinge. The HDPE flexure hinge has the lowest amplification ratios among these plastic types. With the optimal injection parameter and the input value of 218 µm, the HDPE flexure hinge could create a maximum average output value of 699.8 µm. The results provide more insight into plastic flexure hinges and broaden their applications by finding the optimal injection parameters and plastic types.

Weld Line Strength of Polyamide Fiberglass Composite at Different Processing Parameters in Injection Molding Technique.

This study examines the impact of injection parameters on the weld line strength of the polyamide 6 and 30% fiberglass (PA6 + 30% FG) composite samples. The effects of filling time, packing time, packing pressure, melt temperature, and mold temperature on the ultimate tensile strength (UTS) and the elongation value of the weld line are investigated. The results reveal that the filling time factor has the lowest influence rate. On the contrary, the packing pressure has the most considerable value of UTS standard deviation, indicating that this factor has a high impact rate. The melt temperature factor has the highest elongation standard deviation, pointing out the strong impact of melt temperature on the elongation value. In reverse, the filling time factor has the lowest elongation standard deviation, showing the low impact of this factor on the elongation value. Increasing the mold temperature enhances the elongation value greatly because a higher temperature generates a better connection in the weld line area. Although the UTS value improves modestly when the mold temperature control system is used, the elongation result from the mold temperature parameter is better than expected. The UTS result from all parameters presents a minor deviation; therefore, it is lower than expected. The optimal strength result from artificial neural networks with genetic algorithm optimization is 85.1 MPa, which is higher than the best experiment result of 76.8 MPa. Scanning electron microscopy (SEM) results show that the interface between the fiberglass and the PA matrix has high adherence. The fracture surface is smooth, indicating that the PA6 + 30% FG composite sample has a high fragility level. The findings could help to increase the injection sample's weld line strength by optimizing the injection molding conditions.

Nanoscale friction behavior and deformation during copper chemical mechanical polishing process.

CONTEXT: The mechanical characteristics and deformation behavior of Cu material under the nanoscratching through a diamond tooltip on the workpiece are studied using molecular dynamics (MD) simulation. Effects of scratching velocity, scratching depth, workpiece temperature, and grain size on the total force, shear strain, pile-up, shear stress, workpiece temperature, and phase transformation are investigated. The results reveal that increasing the scratching velocity leads to higher oscillation in total force, greater shear strain and shear stress, higher pile-up on the workpiece surface, and higher workpiece temperatures. The effect of the scratching velocity on phase transformation shows that most of the dislocation is a transformation structure from the FCC structure to the HCP, BCC, and other structures in all workpieces during the nanoscratching process. In addition, with increasing the scratching depth, material pile-up becomes more prominent, consequently elevating the contact area between the diamond tooltip and the workpiece, which simultaneously leads to an increase in total force, shear strain, pile-up, shear stress, and workpiece temperature. The MD simulation results revealed that the subsurface region of nanoscratched Cu single-crystal experiences the formation of stacking faults, vacancy defects, and cluster vacancies. In studying the effect of workpiece temperature, the results show that higher temperatures lead to the decline of scratching force, high plastic deformation, increased shear strain and stress, lower pile-up height, and high transition from the FCC structure to both other and BCC structures. For polycrystalline structures, the force curves occur in the oscillation state in all cases of different grain sizes because of the dislocation deformation during the cutting process. The maximum force decreases with diminishing grain size, attributed to the inverse Hall-Petch relation. As the grain size increases, leading to a decrease in the shear strain, stress, and an uneven pile up; also, the HCP structure rises with decreasing grain boundary and the partial dislocation and stacking fault mobilize inside grains. METHODS: By using molecular dynamics (MD) simulation based on the Large-scale Atomic/Molecular Massively Parallel Simulator (LAMMPS) software, all molecular interactions were described by the Lennard-Jones (LJ) and embedded atom method (EAM) potentials. In order to mitigate the effects of temperature fluctuations, the system employs an isothermal and isobaric (NPT) ensemble for precise temperature control. The temperature was set as 300 K and the time step was 1 fs (femtosecond).

Trajectory Strategy Effects on the Material Characteristics in the WAAM Technique.

The wire Arc Additive Manufacturing (WAAM) technique has evolved into a cutting-edge 3D printing technique. This study surveys the influences of trajectory on the characteristics of low-carbon steel samples generated by the WAAM technique. The results show that the grains in the WAAM samples are isotropic, with grain size numbers ranging from 7 to 12. Strategy 3, with a spiral trajectory, has the smallest grain size, while strategy 2, with a lean zigzag trajectory, has the largest. The variations in grain size are caused by differences in heat input and output during the printing process. The WAAM samples achieve a significantly higher UTS value than the original wire, demonstrating the WAAM technique's benefit. Strategy 3, with a spiral trajectory, achieves the highest UTS value, 616.5 MPa, 24% higher than the original wire. The UTS values of strategy 1 (horizontal zigzag trajectory) and strategy 4 (curve zigzag trajectory) are comparable. WAAM samples have significantly higher elongation values than the original wire, with only 22% elongation. The sample with the highest elongation value, 47.2%, was produced by strategy 3. Strategy 2 has an elongation value of 37.9%. The value of elongation is proportional to the value of UTS. WAAM samples have average elastic modulus values of 95.8 GPa, 173.3 GPa, 92.2 GPa, and 83.9 GPa, corresponding to strategies 1, 2, 3, and 4. Only a strategy 2 sample has a similar elastic modulus value to the original wire. All samples have dimples on the fracture surface, indicating that the WAAM samples are ductile. These fracture surfaces' equiaxial shape corresponds to the original microstructure's equiaxial shape. The results provide the optimal trajectory for the WAAM products is the spiral trajectory, while the lean zigzag trajectory gains only modest characteristics.

Conformal Cooling Channel Design for Improving Temperature Distribution on the Cavity Surface in the Injection Molding Process.

Mold heating is an essential process in plastic injection molding. Raising the temperature of the mold before injecting liquefied plastic can ease the mold-filling process. A cooling channel can be used to transport high-temperature fluids for this purpose, such as hot water or oil. This dual purpose is a cost-effective solution for heating the mold because the target temperature is easily achieved using this method. In addition, a conformal cooling channel (CCC) can provide more efficient mold heating than a straight cooling channel. This study used the response surface methodology to determine the optimum CCC shape for heat distribution in a mold, and the simulation results confirmed its optimization. The average temperature of the mold using a CCC was better than that using a straight cooling channel, and the heat zone was uniform across the mold surface.

Enhancing the Fatigue Strength of the Weld Line in Advanced Polymer Injection Molding: Gas-Assisted Mold Temperature Control for Thermoplastic Polyurethane (TPU) Composites.

This study presents an innovative approach to enhancing weld line strength in advanced polymer injection molding through applying gas-assisted mold temperature control, significantly increasing mold temperature beyond typical values observed in conventional processes. We investigate the effects of various heating times and frequencies on the fatigue strength of Polypropylene (PP) samples and the tensile strength of Acrylonitrile Butadiene Styrene (ABS) composite samples at different Thermoplastic Polyurethane (TPU) percentages and heating times. Using gas-assisted mold heating, mold temperatures exceeding 210 °C are achieved, which represents a significant advancement compared to the standard mold temperatures of less than 100 °C. As a result, the fatigue strength of the PP sample with mold heating at 15 s shows a remarkable increase of up to 5.4 times at 5 Hz compared to the sample without mold temperature control. Moreover, ABS/TPU blends with 15 wt.% TPU exhibit the highest ultimate tensile strength (UTS) value of 36.8 MPa, while blends with 30 wt.% TPU have the lowest UTS value of 21.3 MPa. This advancement demonstrates the potential for improved welding line bonding and fatigue strength in manufacturing. Our findings reveal that increasing the mold temperature before injection results in higher fatigue strength in the weld line, with the TPU percentage having a more significant influence on the mechanical properties of ABS/TPU blends than heating time. The results of this study contribute to a deeper understanding of advanced polymer injection molding and offer valuable insights for process optimization.

Influences of TPU Content on the Weld Line Characteristics of PP and ABS Blends.

This study aims to explore the effects of Thermoplastic Polyurethane (TPU) content on the weld line properties of Polypropylene (PP) and Acrylonitrile Butadiene Styrene (ABS) blends. In PP/TPU blends, increasing the TPU content results in a significant decrease in the PP/TPU composite's ultimate tensile strength (UTS) and elongation values. Blends with 10 wt%, 15 wt%, and 20 wt% TPU and pure PP outperform blends with 10 wt%, 15 wt%, and 20 wt% TPU and recycled PP in terms of UTS value. The blend with 10 wt% TPU and pure PP achieves the highest UTS value of 21.85 MPa. However, the blend's elongation decreases due to the poor bonding in the weld line area. According to Taguchi's analysis, the TPU factor has a more significant overall influence on the mechanical properties of PP/TPU blends than the recycled PP factor. Scanning electron microscope (SEM) results show that the TPU area has a dimple shape on the fracture surface due to its significantly higher elongation value. The 15 wt% TPU sample achieves the highest UTS value of 35.7 MPa in ABS/TPU blends, which is considerably higher than other cases, indicating good compatibility between ABS and TPU. The sample containing 20 wt% TPU has the lowest UTS value of 21.2 MPa. Furthermore, the elongation-changing pattern corresponds to the UTS value. Interestingly, SEM results present that the fracture surface of this blend is flatter than the PP/TPU blend due to a higher compatibility rate. The 30 wt% TPU sample has a higher rate of dimple area than the 10 wt% TPU sample. Moreover, ABS/TPU blends gain a higher UTS value than PP/TPU blends. Increasing the TPU ratio mainly reduces the elastic modulus of both ABS/TPU blends and PP/TPU blends. This study reveals the advantages and disadvantages of mixing TPU with PP or ABS to ensure that it meets the requirements of the intended applications.

Influences of Material Selection, Infill Ratio, and Layer Height in the 3D Printing Cavity Process on the Surface Roughness of Printed Patterns and Casted Products in Investment Casting.

As 3D-printed (3DP) patterns are solid and durable, they can be used to create thin wall castings, which is complicated with wax patterns because of the wax's fragility and high shrinkage ratio. According to this study's experiment results, polylactic acid (PLA), polyvinyl butyral (PVB), and castable wax (CW) are suitable materials for preparing investment casting (IC) cavities. The results indicate that the casting product with the highest-quality surface is obtained using a cavity prepared using a CW-printed pattern. PLA- and PVB-printed patterns provide a good surface finish for casted products. In addition, the roughness of both the printed and casted surfaces increases as the printing layer height increases. The roughness of the casted surface varies from 2.25 µm to 29.17 µm. This investigation also considers the correlation between the infill ratio and mechanical properties of PLA-printed patterns. An increase in the infill ratios from 0% to 100% leads to a significant increase in the tensile properties of the PLA-printed pattern. The obtained results can be practically used.

Study on the Fatigue Strength of Welding Line in Injection Molding Products under Different Tensile Conditions.

The fatigue performance of polypropylene (PP) at various amplitudes and frequencies on fatigue cycles under tensile test conditions is investigated in this study. The results show that increasing the frequency leads to a decrease in fatigue cycles due to increased cycle time. The decline rate can be divided into two stages, between 1 and 5 Hz. The first stage rapidly decreases fatigue performance as the frequency increases from 1 Hz to 2 Hz or 3 Hz. The second stage has a lower reduction rate, which occurs between 2 Hz or 3 Hz and 5 Hz due to the strengthening effect of increasing frequency. Furthermore, increasing the amplitude from 0.1 mm to 0.4 mm reduces the fatigue cycle due to the higher deformation rate. In summary, expanding both amplitude and frequency reduces the fatigue performance of the PP material. Moreover, according to the scanning electron microscope microstructure, increasing the frequency results in more microcracks in the polymer matrix.

Phase transformation and subsurface damage formation in the ultrafine machining process of a diamond substrate through atomistic simulation.

This report explores the effects of machining depth, velocity, temperature, multi-machining, and grain size on the tribological properties of a diamond substrate. The results show that the appearance of graphite atoms can assist the machining process as it reduces the force. Moreover, the number of graphite atoms relies on the machining speed and substrate temperature improvement caused by the friction force. Besides, machining in a machined surface for multi-time is affected by its rough, amorphous, and deformed surface. Therefore, machining in the vertical direction for multi-time leads to a higher rate of deformation but a reduction in the rate of graphite atoms generation. Increasing the grain size could produce a larger graphite cluster, a higher elastic recovery rate, and a higher temperature but a lower force and pile-up height. Because the existence of the grain boundaries hinders the force transformation process, and the reduction in the grain size can soften the diamond substrate material.

Stepwise replication identifies a low-producing lymphotoxin-alpha allele as a major risk factor for early-onset leprosy.

Host genetics has an important role in leprosy, and variants in the shared promoter region of PARK2 and PACRG were the first major susceptibility factors identified by positional cloning. Here we report the linkage disequilibrium mapping of the second linkage peak of our previous genome-wide scan, located close to the HLA complex. In both a Vietnamese familial sample and an Indian case-control sample, the low-producing lymphotoxin-alpha (LTA)+80 A allele was significantly associated with an increase in leprosy risk (P = 0.007 and P = 0.01, respectively). Analysis of an additional case-control sample from Brazil and an additional familial sample from Vietnam showed that the LTA+80 effect was much stronger in young individuals. In the combined sample of 298 Vietnamese familial trios, the odds ratio of leprosy for LTA+80 AA/AC versus CC subjects was 2.11 (P = 0.000024), which increased to 5.63 (P = 0.0000004) in the subsample of 121 trios of affected individuals diagnosed before 16 years of age. In addition to identifying LTA as a major gene associated with early-onset leprosy, our study highlights the critical role of case- and population-specific factors in the dissection of susceptibility variants in complex diseases.

Age is an important risk factor for onset and sequelae of reversal reactions in Vietnamese patients with leprosy.

BACKGROUND: Reversal, or type 1, leprosy reactions (T1Rs) are acute immune episodes that occur in skin and/or nerves and are the leading cause of neurological impairment in patients with leprosy. T1Rs occur mainly in patients with borderline or multibacillary leprosy, but little is known about additional risk factors. METHODS: We enrolled 337 Vietnamese patients with leprosy in our study, including 169 subjects who presented with T1Rs and 168 subjects with no history of T1Rs. A multivariate analysis was used to determine risk factors for T1R occurrence, time to T1R onset after leprosy diagnosis, and T1R sequelae after treatment. RESULTS: Prevalence of T1Rs was estimated to be 29.1%. Multivariate analysis identified 3 clinical features of leprosy associated with T1R occurrence. Borderline leprosy subtype (odds ratio, 6.3 [95% confidence interval, 2.9-13.7] vs. polar subtypes) was the major risk factor; 2 other risk factors were positive bacillary index and presence of > 5 skin lesions. In addition, age at leprosy diagnosis was a strong independent risk factor for T1Rs (odds ratio, 2.4 [95% confidence interval, 1.3-4.4] for patients aged > or = 15 years old vs. < 15 years old). We observed that T1Rs with neuritis occurred significantly earlier than pure skin-related T1Rs. Sequelae were present in 45.1% of patients who experienced T1Rs after treatment. The presence of a motor or sensory deficit at T1R onset was an independent risk factor for sequelae, as was the age at diagnosis of leprosy (odds ratio, 4.4 [95% confidence interval, 1.7-11.6] for patients > or = 20 years old vs. < 20 years old). CONCLUSION: In addition to specific clinical features of leprosy, age is an important risk factor for both T1R occurrence and sequelae after treatment for T1Rs.

Susceptibility to leprosy is associated with PARK2 and PACRG.

Leprosy is caused by Mycobacterium leprae and affects about 700,000 individuals each year. It has long been thought that leprosy has a strong genetic component, and recently we mapped a leprosy susceptibility locus to chromosome 6 region q25-q26 (ref. 3). Here we investigate this region further by using a systematic association scan of the chromosomal interval most likely to harbour this leprosy susceptibility locus. In 197 Vietnamese families we found a significant association between leprosy and 17 markers located in a block of approx. 80 kilobases overlapping the 5' regulatory region shared by the Parkinson's disease gene PARK2 and the co-regulated gene PACRG. Possession of as few as two of the 17 risk alleles was highly predictive of leprosy. This was confirmed in a sample of 975 unrelated leprosy cases and controls from Brazil in whom the same alleles were strongly associated with leprosy. Variants in the regulatory region shared by PARK2 and PACRG therefore act as common risk factors for leprosy.