High Conductivity, Semiconducting, and Metallic PEDOT:PSS Electrode for All-Plastic Solar Cells.

Plastic electrodes are desirable for the rapid development of flexible organic electronics. In this article, a plastic electrode has been prepared by employing traditional conducting polymer poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) and plastic substrate polyethersulfone (PES). The completed electrode (Denote as HC-PEDOT:PSS) treated by 80% concentrated sulfuric acid (H2SO4) possesses a high electrical conductivity of over 2673 S/cm and a high transmittance of over 90% at 550 nm. The high conductivity is attributed to the regular arrangement of PEDOT molecules, which has been proved by the X-ray diffraction characterization. Temperature-dependent conductivity measurement reveals that the HC-PEDOT:PSS possesses both semiconducting and metallic properties. The binding force and effects between the PEDOT and PEI are investigated in detail. All plastic solar cells with a classical device structure of PES/HC-PEDOT:PSS/PEI/P3HT:ICBA/EG-PEDOT:PSS show a PCE of 4.05%. The ITO-free device with a structure of Glass/HC-PEDOT:PSS/Al4083/PM6:Y6/PDINO/Ag delivers an open-circuit voltage (VOC) of 0.81 V, short-circuit current (JSC ) of 23.5 mA/cm2, fill factor (FF) of 0.67 and a moderate power conversion efficiency (PCE) of 12.8%. The above results demonstrate the HC-PEDOT:PSS electrode is a promising candidate for all-plastic solar cells and ITO-free organic solar cells.

Highly Stable Supercapacitors Enabled by a New Conducting Polymer Complex PEDOT:CF3 SO2(x) PSS(1-x).

Herein, a novel conducting polymer complex PEDOT:CF3 SO2(x) PSS(1-x) [denoted as S-PEDOT:CF3 SO2(x) PSS(1-x) , where PEDOT is poly(3,4-ethylenedioxythiophene) and PSS is poly(styrene sulfonate)], is fabricated with the assistance of zinc di[bis(trifluoromenthylsulfonyl) imide][Zn(TFSI)2 ] (CFE). The introduction of CF3 SO2 - group is expected to bring better stability of PEDOT:CF3 SO2 than PEDOT:PSS due to its strong Coulomb force. Electrochemical measurement shows that a high specific capacitance of 194 F cm-3 was achieved from the novel complex S-PEDOT:CF3 SO2(x) PSS(1-x) , the highest value reported so far. An all-solid-state supercapacitor assembly with a structure of S-PEDOT:CF3 SO2(x) PSS(1-x) /H2 SO4 :polyvinyl alcohol (PVA)/S-PEDOT:CF3 SO2(x) PSS(1-x) shows a record specific capacitance of 70.9 F cm-3 and a maximum energy density of 6.02 mWh cm-3 at a power density of 397 mW cm-3 . This supercapacitor device demonstrates excellent electrochemical stability with a capacitance retention rate of 98 % after 10 000 cycles and extreme air stability of 96 % capacitance retention rate after 10 000 cycles, even if the device is exposed to air over 2880 h, much better than that of PEDOT:PSS based supercapacitors. Excellent capacitance can be achieved from PEDOT:CF3 SO2(x) PSS(1-x) electrode under electrolyte-free conditions. This work provides a novel method for high performance stable supercapacitors and may pave the way for the commercialization of PEDOT based supercapacitors.

Fe3O4 nanoparticles encapsulated in boron nitride support via N-doped carbon layer as a peroxymonosulfate activator for pollutant degradation: Important role of metal boosted C-N sites.

Developing highly efficient and stable catalysts for peroxymonosulfate (PMS) based advanced oxidation processes (AOPs) are crucial in the field of environmental remediation. In this work, a facile encapsulated-precursor pyrolysis strategy was reported to prepare a competent PMS-activation catalyst, in which uniformly distributed Fe3O4 nanoparticles were firmly anchored on porous boron nitride (BN) nanosheets by N-doped carbon shell (NC layer). Taking advantage of strong metal-support interaction, the as-synthesized catalyst (BFA-500) could efficiently activate PMS to achieve 100% removal of 4-chlorophenol (4-CP) in 6 min, and the corresponding turnover frequency (TOF) value was 1-2 orders of magnitude higher than that of the benchmark homogeneous (Fe2+) and nanoparticle (Fe0 and Fe3O4) catalysts. Moreover, the well protected encapsulated structure of BFA-500 ensured the remarkable stability that could effectively resist the interference of complex water environment, including initial pH value, various inorganic ions and actual water, and its catalytic activity remained almost unchanged in 5 use-regeneration cycles. More importantly, the generation of O2•- and 1O2 radicals for the 4-CP removal in BFA-500/PMS system was ascribed to Fe3O4 boosted C-N sites containing pyridinic N, where electrons transferred from the embedded Fe3O4 nanoparticles to C-N sites to secure the PMS dissociation into reactive radicals. Overall, this work provided a promising way to design desired PMS-activation catalyst toward wastewater purification.

Progress in Synthesis of Conductive Polymer Poly(3,4-Ethylenedioxythiophene).

PEDOT is the most popularly used conductive polymer due to its high conductivity, good physical and chemical stability, excellent optical transparency, and the capabilities of easy doping and solution processing. Based on the advantages above, PEDOT has been widely used in various devices for energy conversion and storage, and bio-sensing. The synthesis method of PEDOT is very important as it brings different properties which determine its applications. In this mini review, we begin with a brief overview of recent researches in PEDOT. Then, the synthesis methods of PEDOT are summarized in detail, including chemical polymerization, electrochemical polymerization, and transition metal-mediated coupling polymerization. Finally, research directions in acquiring high-quality PEDOT are discussed and proposed.