A new method to evaluate the influence of the glenosphere positioning on stability and range of motion of a reverse shoulder prosthesis.

PURPOSE: Shoulder instability and reduced range of motion are two common complications of a total reverse shoulder arthroplasty. In this work, a new approach is proposed to estimate how the glenoid component positioning can influence the stability and the range of motion of a reverse shoulder prosthesis. MATERIALS AND METHODS: A standard reverse shoulder prosthesis has been analysed. To perform virtual simulation of the shoulder-prosthesis assembly, all the components of the prosthesis have been acquired via a 3D laser scanner and the solid models of the shoulder bones have been reconstructed through CT images. Loads on the shoulder joint have been estimated using anatomical models database. A new virtual/numerical procedure has been implemented using a 3D parametric modelling software to find the optimal position of the glenosphere. RESULTS: Several analyses have been performed using different configurations obtained by changing the glenoid component tilt and the lateral position of the glenosphere, modified through the insertion of a cylindrical spacer. For the analysed case study, it was found that the interposition of a spacer (between the baseplate and the glenoid) and 15° inferior tilt of the glenosphere allow improving the range of motion and the stability of the shoulder. CONCLUSIONS: Some common complications of the reverse shoulder arthroplasty could be effectively reduced by a suitable positioning of the prosthesis components. In this work, using a new method based on virtual simulations, the influence of the glenosphere positioning has been investigated. An optimal configuration for the analysed case study has been found. The proposed approach could be used to find, with no in vivo experiments, the optimal position of a reverse shoulder prosthesis depending on the different dimensions and shape of the bones of each patient.

Virtual simulation of an osseointegrated trans-humeral prosthesis: A falling scenario.

INTRODUCTION: Traditional prosthetic solutions expose the amputee to numerous problems that limit his ability to safely perform the normal activities of daily life. In order to eliminate the problems related to the use of the traditional prosthesis with socket, a new technique was developed for fixing the prosthesis to the amputees based on the principle of osseointegration. The aim of this paper is to study and analyze the stress distribution on the interface between a trans-humeral osseointegrated prosthetic implant and the residual bone, identifying the most stressed areas and thus foreseeing possible failure phenomena of the entire prosthetic system and, after, to compare the stress distribution on three different prosthetic designs that differ from each other for some geometric characteristics. MATERIALS AND METHODS: A healthy individual mimics two fall scenarios of which the trans-humeral amputees can most likely be victims: Static fall and Dynamic fall. A force platform (P-6000, BTS Bioengineering) is required for load data acquisition. The CAD model of the trans-humeral osseointegrated implant was created following the guidelines of the OPRA implant. The bone model was created starting from the CAT scan of a left humerus. The FEM simulation was conducted throught a linear analysis. RESULTS: Both during static fall and dynamic fall, similar trends have been observed for the reaction force Fz, the torque moment Tz, the bending moments Mx and My. From the analysis of the von Mises stress distribution it was found that the stress distribution is more homogeneous in the case where the thread of the fixture is made by a triangular profile with height of the thread equal to 0.5 mm. However, it can be seen that, when passing from a thread with height of 0.5 mm to a 1 mm, there is a slight decrease in the stress on the whole contact zone between the fixture and the humerus. The same improvement can also be seen in the case of trapezoidal threading. CONCLUSION: By modifying the height and/or by varying the thread profile, are obtained slightly better results with respect to the case with a 0.5 mm height triangular thread.

Optimal positioning of the humeral component in the reverse shoulder prosthesis.

INTRODUCTION: Total reverse shoulder arthroplasty is becoming more and more the standard therapeutic practice for glenohumeral arthropathy with massive lesions of the rotator cuff. The biomechanical principle of this prosthesis is represented by the reversion of the normal anatomy of the shoulder joint. This non-anatomical prosthesis leads to a medialization of the rotation centre of the glenohumeral joint and also to a distalization of the humeral head. All that causes a deltoid tension increasing so allowing a larger abduction of the arm. Main complications of the reverse shoulder prosthesis are due to the joint instability, the scapular notching and the wear of the polyethylene insert. PURPOSE: The main goal of the present work is to study the effect of the positioning of the humeral component on the intrinsic stability of the reverse shoulder prosthesis. In particular, through finite element method simulations, the variation of the stability ratio of the shoulder joint has been calculated for both vertical and horizontal dislocating loads depending on the humeral stem version angle. Moreover, in order to estimate the wear of the polyethylene cup, some analyses have been developed to calculate the pressures on the polyethylene insert. RESULTS: The obtained results demonstrate the dislocation of a shoulder prosthesis and the wear of the polyethylene insert can be prevented or limited by conveniently varying the version angle of the humeral component.