An experimental investigation of spin-on doping optimization for enhanced electrical characteristics in silicon homojunction solar cells: Proof of concept.

The pursuit of enhancing the performance of silicon-based solar cells is pivotal for the progression of solar photovoltaics as the most potential renewable energy technologies. Despite the existence of sophisticated methods like diffusion and ion implantation for doping phosphorus into p-type silicon wafers in the semiconductor industry, there is a compelling need to research spin-on doping techniques, especially in the context of tandem devices, where fabricating the bottom cell demands meticulous control over conditions. The primary challenge with existing silicon cell fabrication methods lies in their complexity, cost, and environmental concerns. Thus, this research focuses on the optimization of parameters, such as, deposition of the spin on doping layer, emitter thickness (Xj), and dopant concentration (ND) to maximize solar cell efficiency. We utilized both fabrication and simulation techniques to delve into these factors. Employing silicon wafer thickness of 625 µm, the study explored the effects of altering the count of dopant layers through the spin-on dopant (SOD) technique in the device fabrication. Interestingly, the increase of the dopant layers from 1 to 4 enhances efficiency, whereby, further addition of 6 and 8 layers worsens both series and shunt resistances, affecting the solar cell performance. The peak efficiency of 11.75 % achieved in fabrication of 4 layers dopant. By using device simulation with wxAMPS to perform a combinatorial analysis of Xj and ND, we further identified the optimal conditions for an emitter to achieve peak performance. Altering Xj between 0.05 µm and 10 µm and adjusting ND from 1e+15 cm-3 to 9e+15 cm-3, we found that maximum efficiency of 14.18 % was attained for Xj = 1 µm and ND = 9e+15 cm-3. This research addresses a crucial knowledge gap, providing insights for creating more efficient, cost-effective, and flexible silicon solar cells, thereby enhancing their viability as a sustainable energy source.

Integrating local and global information to identify influential nodes in complex networks.

Centrality analysis is a crucial tool for understanding the role of nodes in a network, but it is unclear how different centrality measures provide much unique information. To improve the identification of influential nodes in a network, we propose a new method called Hybrid-GSM (H-GSM) that combines the K-shell decomposition approach and Degree Centrality. H-GSM characterizes the impact of nodes more precisely than the Global Structure Model (GSM), which cannot distinguish the importance of each node. We evaluate the performance of H-GSM using the SIR model to simulate the propagation process of six real-world networks. Our method outperforms other approaches regarding computational complexity, node discrimination, and accuracy. Our findings demonstrate the proposed H-GSM as an effective method for identifying influential nodes in complex networks.

Elucidating the Effects of Interconnecting Layer Thickness and Bandgap Variations on the Performance of Monolithic Perovskite/Silicon Tandem Solar Cell by wxAMPS.

In this study, we investigated the pathways for integration of perovskite and silicon solar cells through variation of the properties of the interconnecting layer (ICL). The user-friendly computer simulation software wxAMPS was used to conduct the investigation. The simulation started with numerical inspection of the individual single junction sub-cell, and this was followed by performing an electrical and optical evaluation of monolithic 2T tandem PSC/Si, with variation of the thickness and bandgap of the interconnecting layer. The electrical performance of the monolithic crystalline silicon and CH3NH3PbI3 perovskite tandem configuration was observed to be the best with the insertion of a 50 nm thick (Eg ≥ 2.25 eV) interconnecting layer, which directly contributed to the optimum optical absorption coverage. These design parameters improved the optical absorption and current matching, while also enhancing the electrical performance of the tandem solar cell, which benefited the photovoltaic aspects through lowering the parasitic loss.

Recent Advances in Synthesis of Graphite from Agricultural Bio-Waste Material: A Review.

Graphitic carbon is a valuable material that can be utilized in many fields, such as electronics, energy storage and wastewater filtration. Due to the high demand for commercial graphite, an alternative raw material with lower costs that is environmentally friendly has been explored. Amongst these, an agricultural bio-waste material has become an option due to its highly bioactive properties, such as bioavailability, antioxidant, antimicrobial, in vitro and anti-inflammatory properties. In addition, biomass wastes usually have high organic carbon content, which has been discovered by many researchers as an alternative carbon material to produce graphite. However, there are several challenges associated with the graphite production process from biomass waste materials, such as impurities, the processing conditions and production costs. Agricultural bio-waste materials typically contain many volatiles and impurities, which can interfere with the synthesis process and reduce the quality of the graphitic carbon produced. Moreover, the processing conditions required for the synthesis of graphitic carbon from agricultural biomass waste materials are quite challenging to optimize. The temperature, pressure, catalyst used and other parameters must be carefully controlled to ensure that the desired product is obtained. Nevertheless, the use of agricultural biomass waste materials as a raw material for graphitic carbon synthesis can reduce the production costs. Improving the overall cost-effectiveness of this approach depends on many factors, including the availability and cost of the feedstock, the processing costs and the market demand for the final product. Therefore, in this review, the importance of biomass waste utilization is discussed. Various methods of synthesizing graphitic carbon are also reviewed. The discussion ranges from the conversion of biomass waste into carbon-rich feedstocks with different recent advances to the method of synthesis of graphitic carbon. The importance of utilizing agricultural biomass waste and the types of potential biomass waste carbon precursors and their pre-treatment methods are also reviewed. Finally, the gaps found in the previous research are proposed as a future research suggestion. Overall, the synthesis of graphite from agricultural bio-waste materials is a promising area of research, but more work is needed to address the challenges associated with this process and to demonstrate its viability at scale.

Near-Infrared (NIR) Silver Sulfide (Ag2S) Semiconductor Photocatalyst Film for Degradation of Methylene Blue Solution.

A silver sulfide (Ag2S) semiconductor photocatalyst film has been successfully synthesized using a solution casting method. To produce the photocatalyst films, two types of Ag2S powder were used: a commercialized and synthesized powder. For the commercialized powder (CF/comAg2S), the Ag2S underwent a rarefaction process to reduce its crystallite size from 52 nm to 10 nm, followed by incorporation into microcrystalline cellulose using a solution casting method under the presence of an alkaline/urea solution. A similar process was applied to the synthesized Ag2S powder (CF/syntAg2S), resulting from the co-precipitation process of silver nitrate (AgNO3) and thiourea. The prepared photocatalyst films and their photocatalytic efficiency were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and UV-visible spectroscopy (UV-Vis). The results showed that the incorporation of the Ag2S powder into the cellulose films could reduce the peak intensity of the oxygen-containing functional group, which indicated the formation of a composite film. The study of the crystal structure confirmed that all of the as-prepared samples featured a monoclinic acanthite Ag2S structure with space group P21/C. It was found that the degradation rate of the methylene blue dye reached 100% within 2 h under sunlight exposure when using CF/comAg2S and 98.6% for the CF/syntAg2S photocatalyst film, and only 48.1% for the bare Ag2S powder. For the non-exposure sunlight samples, the degradation rate of only 33-35% indicated the importance of the semiconductor near-infrared (NIR) Ag2S photocatalyst used.

Life Cycle Assessment (LCA) of Particleboard: Investigation of the Environmental Parameters.

Particleboard is not entirely a wood replacement but a particular material with its properties, making it more effective at different times than heavy or solid wood. The world's biggest concern is environmental problems with formaldehyde as a particulate board binder that can lead to human carcinogenic agents. A cradle-to-gate life cycle assessment (LCA) of particleboard production was performed using openLCA software. The impact assessment was carried out according to the software's features. This preliminary investigation aims to analyze the chemical composition of particleboard and identify its environmental impact. The Fourier-transform infrared spectroscopy (FTIR) system was used to track the functional group of aliphatic hydrocarbons, inorganic phosphates, and main aliphatic alcohols found in particleboards made in Malaysia. Based on the FTIR results, aliphatic groups were found in numerous aggravates that the spectroscopic infrared was likely to experience. The most important vibrational modes were C-H, at approximately 3000 cm-1, and -CH deformations around 1460 cm-1 and 1380 cm-1. Eight effect groups demonstrated that 100% of the input and all analyses produced the same relative outcome. The life cycle of a product is determined by pollution of the air, water, and soil. Thus, particleboard has a minimal impact on the environment, except for global warming.

Augmentation of the Delamination Factor in Drilling of Carbon Fibre-Reinforced Polymer Composites (CFRP).

Carbon fibre-reinforced polymer (CFRP) composite materials play an increasingly important role in modern manufacturing, and they are among the more prominent materials used in aircraft manufacturing today. However, CFRP is highly prone to delamination and other damage when drilled due to it being extremely strong with a good strength-to-weight ratio and high thermal conductivity. Because of this problem and CFRP's growing importance in aircraft manufacture, research has focused on the entry and exit holes as indicators of damage occurrence during drilling of screws, rivets, and other types of holes. The inside of the hole was neglected in past research and a proper way to quantify the internal side of a hole by combining the entry and exit hole should be included. To fill this gap and improve the use of CFRP, this paper reports a novel technique to measure the holes by using the extension of the adjusted delamination factor (SFDSR) for drilling thick CFRP composites in order to establish the influence of machining input variables on key output measures, i.e., delamination and other damages. The experimental results showed a significant difference in interpretation of the damage during the analysis. Improvement was made by providing better perspectives of identifying hole defects.