Method development for optimizing analysis of ignitable liquid residues using flow-modulated comprehensive two-dimensional gas chromatography.

The abundance and composition of matrix compounds in fire debris samples undergoing ignitable liquid residue analysis frequently leads to inconclusive results, which can be diminished by applying comprehensive two-dimensional gas chromatography (GC × GC). Method development must be undertaken to fully utilize the potential of GC × GC by maximizing separation space and resolution.. The three main areas to consider for method development are column selection, modulator settings and parameter optimization. Seven column combinations with different stationary phase chemistry, column dimensions and orthogonality were assessed for suitability based on target compound selectivity, retention, resolution, and peak shapes, as well as overall peak capacity and area use. Using Box-Behnken design of experimentation (DoE), the effect of modulator settings such as flow ratio and loop fill capacity were evaluated using carbon loading potential, dilution effect, as well as target peak amplitude and skewing effect. The run parameters explored for parameter optimization were oven programming, inlet pressure (column flow rate), and modulation period. Comparing DoE approaches, Box-Behnken and Doehlert designs assessed sensitivity, selectivity, peak capacity, and wraparound; alongside target peak retention, resolution, and shape evaluation. Certified reference standards and simulated wildfire debris were used for method development and verification, and wildfire debris case samples scrutinized for method validation. The final method employed a low polarity column (5% diphenyl) coupled to a semi-polar column (50% diphenyl) and resulted in an average Separation Number (SN) exceeding 1 in both dimensions after optimization. Separation Numbers of 18.16 for first and 1.46 for second dimension without wraparound for compounds with at least four aromatic rings signified successful separation of all target compounds from varied matrix compositions and allowed for easy visual comparison of extracted ion profiles. Mass spectrometry (MS) was required during validation to differentiate ions where no baseline separation between target compounds and extraneous matrix compounds was possible. The resulting method was evaluated against ASTM E1618 and found to be an ideal routine analysis method providing great resolution of target compounds from interferences and excellent potential for ILR classification within a complex sample matrix.

Occupational risk of organophosphates and other chemical and radiative exposure in the aircraft cabin: A systematic review.

Occupational exposure to oil fumes, organophosphates, halogenated flame retardants, and other volatile and semi-volatile contaminants is a concern within the aviation industry. There is no current consensus on the risk attributed to exposure to these chemical classes within the aircraft cabin. Contaminant concentrations rarely exceed conventional air quality guidelines, but concerns have been raised about these guidelines' applicability within the aircraft environment. This systematic review, the largest and most comprehensive completed to date on the subject matter, aims to synthesize the existing research related to chemical and other exposures inside the aircraft cabin to determine the occupational risk that may be attributed said exposure, as well as, determine knowledge gaps in source, pathway, and receptor that may exist. The Science Direct, Scopus, and Web of Science databases were queried with five search terms generating 138 manuscripts that met acceptance criteria and screening. Several potential areas requiring future examination were identified: Potable water on aircraft should be examined as a potential source of pollutant exposure, as should air conditioning expansion turbines. Historical exposure should also be more fully explored, and non-targeted analysis could provide valuable information to comprehend the aircraft cabin exposome. Occupational risk under typical flight scenarios appears to be limited for most healthy individuals. Contaminants of concern were demonstrated to be extant within the cabin, however the concentrations under normal circumstances do not appear to be individually responsible for the symptomologies that are present in impacted individuals. Questions remain regarding those that are more vulnerable or susceptible to exposure. Additionally, establishing the effects of chronic low dose exposure and exposure to contaminant mixtures has not been satisfied. The risk of acute exposure in mitigable fume events is substantial, and technological solutions or the replacement of compounds of concern for safer alternatives should be a priority.

Development of retention time indices for comprehensive multidimensional gas chromatography and application to ignitable liquid residue mapping in wildfire investigations.

In this study, we introduce a simple three-step workflow for a universally applicable RI system, to be used in GC×GC analysis of ignitable liquid residue (ILR) for arson investigations. The proposed RI system applies a combination of two well-established GC RI systems: non-isothermal Kovats (K) index in the first dimension and Lee (L) index in the second dimension. The proposed KLI RI system showed very good correlations when compared with predicted values and existing RI systems (r2 = 0.97 in first dimension, r2 = 0.99 in second dimension) and was valid for a wide range of analyte concentrations and operational settings (coefficient of variance (CV) < 1% in first dimension, < 10% in second dimension). Using the KLI RI, an ILR classification contour map was created to assist with the identification of ILR types within ASTM E1618. The contour map was successfully applied to neat fuels and a fire scene sample, highlighting the application to wildfire investigation. Standardizing the RI process and establishing acceptable error margins allows the exploration and comparison of comprehensive data generated from GC×GC analysis of ILRs regardless of location, time, or system, further enhancing comprehensive and tenable chemometric analyses of samples. Overall, the KLI workflow was inexpensive, quick to apply, and user-friendly with its simple 3-step design.

Biomimicry of vascular plants as a means of saline soil remediation.

Soil salinization impacts millions of hectares of land around the world and threatens many soil ecosystem services. Impacts of soil salinization are long lasting and impact agriculture productivity, reduce plant diversity and cause increase soil erosion due a reduction or loss in surface vegetation. Generally, remediation of saline soil relies on soil washing methods and phytoremediation to translocate salts below the rooting depth of plants. However, standard methods can often be unsuccessful as leached salts are able to return to the rooting zone through subsequent capillary rise in the soil. Surface application of iron (III) ferrocyanide has been used to remediate salt contaminated soil as the ferrocyanide complex induces salts to efflorescence at the soil surface as water evaporates rather than crystallising within the soil matrix. However, surface application of iron (III) ferrocyanide tends to be less successful in clay textured soil and does not work well when subsequent reapplications of water are made for further salt removal. In this study we investigate a biomimetic approach to desalinate soil by mimicking the capillary transport mechanisms employed by vascular plants. Our approach uses evapotranspiration to translocate saline soil water above the soil surface where it is effloresced with ferrocyanides. After 30 days of treatment, the biomimetic approach used 2.1 pore volume equivalents of water and was able to reduce the concentration of salts from 8% (g·NaCl/g·soil) to 0.8% (g·NaCl/g·soil), resulting in a reduction of soil EC from 120 mS/cm to 14 mS/cm. Our findings indicate that the method, with further refinement and expansion to field based trials, could be an effective tool to desalinate soil and reduce global soil salinization.

Changes to polychlorinated biphenyl (PCB) signatures and enantiomer fractions across different tissue types in Guillemots.

Two Guillemot carcases were dissected, each providing 12 discrete tissue samples and 3 samples of partially digested food. One hundred and five PCBs from the 209 PCBs determined by GCxGC-ToFMS were detected. The relative proportions of individual PCBs did not vary greatly within tissue types, although the PCB profile from undigested food could be distinguished. Enantiomer fractions (EFs) were determined for CB-95, CB-136 and CB-149 by GC-HRqToFMS. EFs in the partially digested food were near racemic, with high levels of enrichment for E1 CB-95 in the kidneys and liver (EF of 0.80 and 0.84 respectively). This provides some of the clearest evidence to date that fractionation takes place in the organs where metabolic biotransformation and elimination of PCBs occurs. Our findings also confirm the ability of non-lethal sampling techniques, such as collection of small (<1 g) blood samples, to provide PCB signatures that are representative of an individual organism.

Fate and behavior of oil sands naphthenic acids in a pilot-scale treatment wetland as characterized by negative-ion electrospray ionization Orbitrap mass spectrometry.

Large volumes of oil sands process-affected water (OSPW) are generated during the extraction of bitumen from oil sands in the Athabasca region of northeastern Alberta, Canada. As part of the development of treatment technologies, molecular characterization of naphthenic acids (NAs) and naphthenic acid fraction compounds (NAFC) in wetlands is a topic of research to better understand their fate and behavior in aquatic environments. Reported here is the application of high-resolution negative-ion electrospray Orbitrap-mass spectrometry for molecular characterization of NAs and NAFCs in a non-aerated constructed treatment wetland. The effectiveness of the wetlands to remove OSPW-NAs and NAFCs was evaluated by monitoring the changes in distributions of NAFC compounds in the untreated sample and non-aerated treatment system. After correction for measured evapotranspiration, the removal rate of the classical NAs followed approximately first-order kinetics, with higher rates observed for structures with relatively higher number of carbon atoms. These findings indicate that constructed wetland treatment is a viable method for removal of classical NAs in OSPW. Work is underway to evaluate the effects of wetland design on water quality improvement, preferential removal of different NAFC species, and reduction in toxicity.

Can polychlorinated biphenyl (PCB) signatures and enantiomer fractions be used for source identification and to age date occupational exposure?

Detailed polychlorinated biphenyl (PCB) signatures and chiral Enantiomer Fractions (EFs) of CB-95, CB-136 and CB-149 were measured for 30 workers at a transformer dismantling plant. This was undertaken to identify sources of exposure and investigate changes to the PCB signature and EFs over different exposure periods. Approximately 1.5 g of serum was extracted and PCB signatures were created through analysis by comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry (GC×GC-TOFMS) and EFs calculated following analysis by gas chromatography with high resolution mass spectrometry (GC-HRMS). A total of 84 PCBs were identified in the serum samples with concentrations of the 7 indicator PCBs ranging from 11-350 ng g(-1) of serum (1.2-39 µg g(-1) lipid). The PCB signatures were interpreted using principal component analysis (PCA) which was able to distinguish workers with background or recent minimal exposure from those with prolonged occupational exposure. Occupationally exposed individuals had a similar PCB profile to Aroclor A1260. However, individuals with prolonged exposure had depleted proportions of several PCB congeners that are susceptible to metabolism (CB-95, CB-101 and CB-151) and elevated proportions of PCBs that are resistant to metabolism (CB-74, CB-153, CB-138 and CB-180). The results also identified a third group of workers with elevated proportions of CB-28, CB-60, CB-66, CB-74, CB-105 and CB-118 who appeared to have been exposed to an additional source of PCBs. The results show near complete removal of the CB-95 E2 enantiomer in some samples, indicating that bioselective metabolism or preferential excretion of one enantiomer occurs in humans. By considering PCB concentrations along with detailed congener specific signatures it was possible to identify different exposure sources, and gain an insight into both the magnitude and duration of exposure.

Identifying the provenance of Leach's storm petrels in the North Atlantic using polychlorinated biphenyl signatures derived from comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry.

PCB signatures can be used for source identification, exposure studies, age dating and bio-monitoring. This study uses comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry (GCxGC-ToFMS) to produce a PCB signature comprised of over 80 PCBs for individual Leach's storm petrels (Oceanodroma leucorhoa). The Leach's storm petrel is a relatively small, elusive, understudied pelagic bird, which only returns to remote islands under darkness during the breeding season. Samples were obtained from 25 Leach's storm petrels found dead in Canada and the UK following storm events in 2006 and 2009. Tissue samples were extracted and analysed by GCxGC-ToFMS and results showed that 83 PCB congeners were present in >60% of samples. An assessment of the PCB signature in four different tissue types showed that it did not vary greatly in samples obtained from the gut, heart, liver and stomach. Multivariate statistical analysis identified a distinctive PCB signature in birds from Canada and Europe which was used to identify the regional provenance and transatlantic movement of individual birds. The findings showcase the ability of GCxGC-ToFMS to provide the high quality congener specific analysis that is necessary for PCB fingerprinting, as well as highlighting the potential of PCB signatures for use in ecological studies of movement, foraging and behaviour.

Characterization of naphthenic acids by gas chromatography-Fourier transform ion cyclotron resonance mass spectrometry.

During the bitumen extraction from the oil sands of Alberta, large volumes of process water containing naphthenic acids are stored in tailing ponds. The naphthenic acids along with other components in the processed waters are known to be toxic in aquatic environments. In view of the complex matrix and the toxicity of the processed waters, there is a need for complementary analytical techniques for comprehensive characterization of the naphthenic acid mixtures. This study reports the online gas chromatographic separation of naphthenic acid mixtures prior to ultrahigh resolution mass spectrometry detection, using electron and chemical ionization. Two oil sands processed water samples and two groundwater samples were characterized to evaluate the performance of the instrumental technique. The high mass resolution of the system enabled visualization of the data using Kendrick mass defect plots. The addition of gas chromatographic separations enabled visualization of the data as unique compound class elution fingerprints. The technique is demonstrated to be a valuable tool for chemical fingerprinting of naphthenic acids.

Fingerprinting polychlorinated biphenyls in environmental samples using comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry.

A GC × GC-TOFMS installed with a Rtx-PCB (60 m × 0.18 mm × 0.18 µm) in the first dimension and Rxi- 17 (1.5 m × 0.1 mm × 0.1 µm) column in the second dimension was used to separate 188 out of 209 congeners. A further 12 congeners were identified through additional data processing resulting in the identification of a total of 200 congeners. However, caution is advised if these 12 congeners were to be used in quantitative assessments. The remaining 9 co-eluting congeners were three doublets (CB65 + CB62, CB160 + CB163 and CB201 + CB204) and one triplet (CB20 + CB21 + CB33). This method was tested on five Aroclors and resulted in the separation of all congeners present in the heavier Aroclor mixtures A1254 and A1260. The suitability of this method for applications in biological matrices was demonstrated on extracted whiting and guillemot liver samples which resulted in the identification of 137 individual PCBs in the whiting liver sample and 120 in the guillemot sample. Fingerprinting was able to show clear differences in the PCB signature of the two animals. This highlights the potential of this method for PCB fingerprinting in environmental forensics studies and other assessments that require congener specific analysis.

Elucidating the structural properties that influence the persistence of PCBs in humans using the National Health and Nutrition Examination Survey (NHANES) dataset.

In human exposure studies involving Polychlorinated Biphenyls (PCBs), it is useful to establish when an individual was potentially exposed. Age dating PCB exposure is complex but assessments can be made because different PCB congeners have different residence times in the human body. The less chlorinated congeners generally tend to have shorter residence times because they are biotransformed and eliminated faster than more chlorinated congeners. Therefore, the presence of high proportions of less chlorinated congeners is often indicative of recent exposure. The 2003-04 National Health and Nutrition Examination Survey (NHANES) dataset contains results for the concentration of 37 PCBs in a sub-sample of the US population. Multivariate statistical analysis of the NHANES data showed that less chlorinated congeners are not always biotransformed faster than higher chlorinated compounds. For example, PCB 28 (a tri-chlorobiphenyl) appears to be more resistant to biotransformation than PCB 101 and 110 (penta-chlorobiphenyls). Using statistical analysis of the NHANES data in conjunction with previously published studies on PCB persistence in humans, it was possible to identify the structural relationships that determine if a PCB is likely to be from a recent exposure (termed 'episodic') or from steady state exposure. Congeners with chlorine atoms in the 2,5- and 2,3,6-positions appear to be more susceptible to biotransformation whereas congeners with chlorine bonds in the 2,3,4- 2,4,5- 3,4,5- and 2,3,4,5-positions appear to be more persistent. This work shows that future investigations to date PCB exposure would benefit from the analysis of a wide range of congeners, including the selection of key congeners based not only on the degree of chlorination but also on the positions of the chlorine atoms on the biphenyl.

Development of an advanced on-line position-specific stable carbon isotope system and application to methyl tert-butyl ether.

We present an advanced system for on-line position-specific carbon isotope analysis. The main limitation of on-line intramolecular isotope ratio measurements has been that optimal pyrolytic fragments are obtained mostly at temperatures where the analyte has not completely reacted. As a result of undetermined isotopic fractionation, the isotopic signatures of the pyrolysis products are not strictly equal to these of the equivalent moieties in the parent molecule. We designed a pyrolytic unit in which both temperature and reaction time are variable parameters, enabling determination of the enrichment factor of the pyrolysis at optimal temperature by construction of a Rayleigh plot. In the case of methyl tert-butyl ether (MTBE) presented here, a 'pre-pyrolysis' fractionation of MTBE leading to a depletion of 0.9 per thousand was discovered and the enrichment factor of the optimal pyrolysis reaction was determined at -1.7 per thousand. Absolute delta(13)C values of two functional groups of MTBE - the methoxy group and the 2-methylpropane group - could be determined with 95% confidence intervals of 0.4 per thousand and 0.5 per thousand, respectively.