Hybrid MoS2/h-BN Nanofillers As Synergic Heat Dissipation and Reinforcement Additives in Epoxy Nanocomposites.

Two-dimensional (2D) nanomaterials as molybdenum disulfide (MoS2), hexagonal boron nitride (h-BN), and their hybrid (MoS2/h-BN) were employed as fillers to improve the physical properties of epoxy composites. Nanocomposites were produced in different concentrations and studied in their microstructure, mechanical and thermal properties. The hybrid 2D mixture imparted efficient reinforcement to the epoxy leading to increases of up to 95% in tensile strength, 60% in ultimate strain, and 58% in Young's modulus. Moreover, an enhancement of 203% in thermal conductivity was achieved for the hybrid composite as compared to the pure polymer. The incorporation of MoS2/h-BN mixture nanofillers in epoxy resulted in nanocomposites with multifunctional characteristics for applications that require high mechanical and thermal performance.

Anomalous Li Storage Capability in Atomically Thin Two-Dimensional Sheets of Nonlayered MoO2.

Since the first exfoliation and identification of graphene in 2004, research on layered ultrathin two-dimensional (2D) nanomaterials has achieved remarkable progress. Realizing the special importance of 2D geometry, we demonstrate that the controlled synthesis of nonlayered nanomaterials in 2D geometry can yield some unique properties that otherwise cannot be achieved in these nonlayered systems. Herein, we report a systematic study involving theoretical and experimental approaches to evaluate the Li-ion storage capability in 2D atomic sheets of nonlayered molybdenum dioxide (MoO2). We develop a novel monomer-assisted reduction process to produce high quality 2D sheets of nonlayered MoO2. When used as lithium-ion battery (LIB) anodes, these ultrathin 2D-MoO2 electrodes demonstrate extraordinary reversible capacity, as high as 1516 mAh g-1 after 100 cycles at the current rate of 100 mA g-1 and 489 mAh g-1 after 1050 cycles at 1000 mA g-1. It is evident that these ultrathin 2D sheets did not follow the normal intercalation-cum-conversion mechanism when used as LIB anodes, which was observed for their bulk analogue. Our ex situ XPS and XRD studies reveal a Li-storage mechanism in these 2D-MoO2 sheets consisting of an intercalation reaction and the formation of metallic Li phase. In addition, the 2D-MoO2 based microsupercapacitors exhibit high areal capacitance (63.1 mF cm-2 at 0.1 mA cm-2), good rate performance (81% retention from 0.1 to 2 mA cm-2), and superior cycle stability (86% retention after 10,000 cycles). We believe that our work identifies a new pathway to make 2D nanostructures from nonlayered compounds, which results in an extremely enhanced energy storage capability.

A metal-free electrocatalyst for carbon dioxide reduction to multi-carbon hydrocarbons and oxygenates.

Electroreduction of carbon dioxide into higher-energy liquid fuels and chemicals is a promising but challenging renewable energy conversion technology. Among the electrocatalysts screened so far for carbon dioxide reduction, which includes metals, alloys, organometallics, layered materials and carbon nanostructures, only copper exhibits selectivity towards formation of hydrocarbons and multi-carbon oxygenates at fairly high efficiencies, whereas most others favour production of carbon monoxide or formate. Here we report that nanometre-size N-doped graphene quantum dots (NGQDs) catalyse the electrochemical reduction of carbon dioxide into multi-carbon hydrocarbons and oxygenates at high Faradaic efficiencies, high current densities and low overpotentials. The NGQDs show a high total Faradaic efficiency of carbon dioxide reduction of up to 90%, with selectivity for ethylene and ethanol conversions reaching 45%. The C2 and C3 product distribution and production rate for NGQD-catalysed carbon dioxide reduction is comparable to those obtained with copper nanoparticle-based electrocatalysts.

Metal-free, single-polymer device exhibits resistive memory effect.

All-polymer, write-once-read-many times resistive memory devices have been fabricated on flexible substrates using a single polymer, poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS). Spin-cast or inkjet-printed films of solvent-modified PEDOT:PSS are used as electrodes, while the unmodified or as-is PEDOT:PSS is used as the semiconducting active layer. The all-polymer devices exhibit an irreversible but stable transition from a low resistance state (ON) to a high resistance state (OFF) at low voltages caused by an electric-field-induced morphological rearrangement of PEDOT and PSS at the electrode interface. However, in the metal-PEDOT:PSS-metal devices, we have shown a metal filament formation switching the device from an initial high resistance state (OFF) to the low resistance state (ON). The all-PEDOT:PSS memory device has low write voltages (<3 V), high ON/OFF ratio (>10(3)), good retention characteristics (>10,000 s), and stability in ambient storage (>3 months).

Kinetics and mechanisms of chlorine dioxide and chlorite oxidations of cysteine and glutathione.

Chlorine dioxide oxidation of cysteine (CSH) is investigated under pseudo-first-order conditions (with excess CSH) in buffered aqueous solutions, p[H+] 2.7-9.5 at 25.0 degrees C. The rates of chlorine dioxide decay are first order in both ClO2 and CSH concentrations and increase rapidly as the pH increases. The proposed mechanism is an electron transfer from CS- to ClO2 (1.03 x 10(8) M(-1) s(-1)) with a subsequent rapid reaction of the CS* radical and a second ClO2 to form a cysteinyl-ClO2 adduct (CSOClO). This highly reactive adduct decays via two pathways. In acidic solutions, it hydrolyzes to give CSO(2)H (sulfinic acid) and HOCl, which in turn rapidly react to form CSO3H (cysteic acid) and Cl-. As the pH increases, the (CSOClO) adduct reacts with CS- by a second pathway to form cystine (CSSC) and chlorite ion (ClO2-). The reaction stoichiometry changes from 6 ClO2:5 CSH at low pH to 2 ClO2:10 CSH at high pH. The ClO2 oxidation of glutathione anion (GS-) is also rapid with a second-order rate constant of 1.40 x 10(8) M(-1) s(-1). The reaction of ClO2 with CSSC is 7 orders of magnitude slower than the corresponding reaction with cysteinyl anion (CS-) at pH 6.7. Chlorite ion reacts with CSH; however, at p[H+] 6.7, the observed rate of this reaction is slower than the ClO2/CSH reaction by 6 orders of magnitude. Chlorite ion oxidizes CSH while being reduced to HOCl, which in turn reacts rapidly with CSH to form Cl-. The reaction products are CSSC and CSO3H with a pH-dependent distribution similar to the ClO2/CSH system.

Kinetics and mechanisms of bromine chloride reactions with bromite and chlorite ions.

Chloride ion catalyzes the reactions of HOBr with bromite and chlorite ions in phosphate buffer (p[H(+)] 5 to 7). Bromine chloride is generated in situ in small equilibrium concentrations by the addition of excess Cl(-) to HOBr. In the BrCl/ClO(2)(-) reaction, where ClO(2)(-) is in excess, a first-order rate of formation of ClO(2) is observed that depends on the HOBr concentration. The rate dependencies on ClO(2)(-), Cl(-), H(+), and buffer concentrations are determined. In the BrCl/BrO(2)(-) reaction where BrCl is in pre-equilibrium with the excess species, HOBr, the loss of absorbance due to BrO(2)(-) is followed. The dependencies on Cl(-), HOBr, H(+), and HPO(4)(2)(-) concentrations are determined for the BrCl/BrO(2)(-) reaction. In the proposed mechanisms, the BrCl/ClO(2)(-) and BrCl/BrO(2)(-) reactions proceed by Br(+) transfer to form steady-state levels of BrOClO and BrOBrO, respectively. The rate constant for the BrCl/ClO(2)(-) reaction [k(Cl)(2)]is 5.2 x 10(6) M(-1) s(-1) and for the BrCl/BrO(2)(-) reaction [k(Br)(2)]is 1.9 x 10(5) M(-1) s(-1). In the BrCl/ClO(2)(-) case, BrOClO reacts with ClO(2)(-) to form two ClO(2) radicals and Br(-). However, the hydrolysis of BrOBrO in the BrCl/BrO(2)(-) reaction leads to the formation of BrO(3)(-) and Br(-).

Chlorine dioxide reduction by aqueous iron(II) through outer-sphere and inner-sphere electron-transfer pathways.

The reduction of ClO(2) to ClO(2)(-) by aqueous iron(II) in 0.5 M HClO(4) proceeds by both outer-sphere (86%) and inner-sphere (14%) electron-transfer pathways. The second-order rate constant for the outer-sphere reaction is 1.3 x 10(6) M(-1) s(-1). The inner-sphere electron-transfer reaction takes place via the formation of FeClO(2)(2+) that is observed as an intermediate. The rate constant for the inner-sphere path (2.0 x 10(5) M(-1) s(-1)) is controlled by ClO(2) substitution of a coordinated water to give an inner-sphere complex between ClO(2) and Fe(II) that very rapidly transfers an electron to give (Fe(III)(ClO(2)(-))(H(2)O)(5)(2+))(IS). The composite activation parameters for the ClO(2)/Fe(aq)(2+) reaction (inner-sphere + outer-sphere) are the following: DeltaH(r)++ = 40 kJ mol(-1); DeltaS(r)++ = 1.7 J mol(-1) K(-1). The Fe(III)ClO(2)(2+) inner-sphere complex dissociates to give Fe(aq)(3+) and ClO(2)(-) (39.3 s(-1)). The activation parameters for the dissociation of this complex are the following: DeltaH(d)++= 76 kJ mol(-1); DeltaS(d)++= 32 J K(-1) mol(-1). The reaction of Fe(aq)(2+) with ClO(2)(-) is first order in each species with a second-order rate constant of k(ClO2)- = 2.0 x 10(3) M(-1) s(-1) that is five times larger than the rate constant for the Fe(aq)(2+) reaction with HClO(2) in H(2)SO(4) medium ([H(+)] = 0.01-0.13 M). The composite activation parameters for the Fe(aq)(2+)/Cl(III) reaction in H(2)SO(4) are DeltaH(Cl(III))++ = 41 kJ mol(-1) and DeltaS(Cl(III))++ = 48 J mol(-1) K(-1).

New pathways for chlorine dioxide decomposition in basic solution.

The product distribution from the decay of chlorine dioxide in basic solution changes as the ClO(2) concentration decreases. While disproportionation reactions that give equal amounts of ClO(2)(-) and ClO(3)(-) dominate the stoichiometry at millimolar or higher levels of ClO(2), the ratio of ClO(2)(-) to ClO(3)(-) formed increases significantly at micromolar ClO(2) levels. Kinetic evidence shows three concurrent pathways that all exhibit a first-order dependence in [OH(-)] but have variable order in [ClO(2)]. Pathway 1 is a disproportionation reaction that is first order in [ClO(2)]. Pathway 2, a previously unknown reaction, is also first order in [ClO(2)] but forms ClO(2)(-) as the only chlorine-containing product. Pathway 3 is second order in [ClO(2)] and generates equal amounts of ClO(2)(-) and ClO(3)(-). A Cl(2)O(4) intermediate is proposed for this path. At high concentrations of ClO(2), pathway 3 causes the overall ClO(3)(-) yield to approach the overall yield of ClO(2)(-). Pathway 2 is attributed to OH(-) attack on an oxygen atom of ClO(2) that leads to peroxide intermediates and yields ClO(2)(-) and O(2) as products. This pathway is important at low levels of ClO(2).