Nanoarchitected graphene/copper oxide nanoparticles/MoS2 ternary thin films as highly efficient electrodes for aqueous sodium-ion batteries.

Sodium-ion batteries (SIBs) operating in aqueous electrolyte are an emerging technology that promises to be safer, cheaper, more sustainable and more efficient than their lithium-based counterparts. One of the great challenges associated with this technology is the development of advanced materials with high specific capacity to be used as electrodes. Herein, we describe an ingenious strategy to prepare unprecedented tri-component nanoarchitected thin films with superior performance when applied as anodes in aqueous SIBs. Taking advantage of the broadness and versatility of the liquid-liquid interfacial route, three transparent nanocomposite films comprising graphene, molybdenum sulphide and copper oxide nanoparticles have been prepared. The samples were characterized using several techniques, and the results demonstrated that depending on the specific experimental strategy, different nanoarchitectures are achieved, resulting in different and improved properties. An astonishing capacity of 1377 mA h g-1 at 0.1 A g-1 and a degree of recovery of 100% were observed for the film in which the interactions among the components were optimized. This is among the highest capacity values reported in the literature and demonstrates the potential of these tri-component materials to be used as anodes in aqueous sodium-ion batteries.

New highly antigenic linear B cell epitope peptides from PvAMA-1 as potential vaccine candidates.

Peptide-based vaccines have demonstrated to be an important way to induce long-lived immune responses and, therefore, a promising strategy in the rational of vaccine development. As to malaria, among the classic vaccine targets, the Apical membrane antigen (AMA-1) was proven to have important B cell epitopes that can induce specific immune response and, hence, became key players for a vaccine approach. The peptides selection was carried out using a bioinformatic approach based on Hidden Markov Models profiles of known antigens and propensity scale methods based on hydrophilicity and secondary structure prediction. The antigenicity of the selected B-cell peptides was assessed by multiple serological assays using sera from acute P.vivax infected subjects. The synthetic peptides were recognized by 45.5%, 48.7% and 32.2% of infected subjects for peptides I, II and III respectively. Moreover, when synthetized together (tripeptide), the reactivity increases up to 62%, which is comparable to the reactivity found against the whole protein PvAMA-1 (57%). Furthermore, IgG reactivity against the tripeptide after depletion was reduced by 42%, indicating that these epitopes may be responsible for a considerable part of the protein immunogenicity. These results represent an excellent perspective regarding future chimeric vaccine constructions that may come to contemplate several targets with the potential to generate the robust and protective immune response that a vivax malaria vaccine needs to succeed.

Facile room temperature synthesis of large graphene sheets from simple molecules.

The largest graphene sample obtained through a chemical reaction under ambient conditions (temperature and pressure), using simple molecules such as benzene or n-hexane as precursors, is reported. Starting from a heterogeneous reaction between solid iron chloride and the molecular precursor (benzene and n-hexane) at a water/oil interface, graphene sheets with micrometric lateral size are obtained as a film deposited at the liquid/liquid (L/L) interface. The pathway involving the cyclization and aromatization of n-hexane to benzene at the L/L interface, and the sequence of conversion of benzene to biphenyl and biphenyl to condensed rings (which originates the graphene structures) was followed by different characterization techniques and a mechanistic proposal is presented. Finally, we demonstrate that this route can be extended for the synthesis of N-doped graphene, using pyridine as the molecular precursor.

One material, multiple functions: graphene/Ni(OH)2 thin films applied in batteries, electrochromism and sensors.

Different nanocomposites between reduced graphene oxide (rGO) and Ni(OH)2 nanoparticles were synthesized through modifications in the polyol method (starting from graphene oxide (GO) dispersion in ethylene glycol and nickel acetate), processed as thin films through the liquid-liquid interfacial route, homogeneously deposited over transparent electrodes and spectroscopically, microscopically and electrochemically characterized. The thin and transparent nanocomposite films (112 to 513 nm thickness, 62.6 to 19.9% transmittance at 550 nm) consist of α-Ni(OH)2 nanoparticles (mean diameter of 4.9 nm) homogeneously decorating the rGO sheets. As a control sample, neat Ni(OH)2 was prepared in the same way, consisting of porous nanoparticles with diameter ranging from 30 to 80 nm. The nanocomposite thin films present multifunctionality and they were applied as electrodes to alkaline batteries, as electrochromic material and as active component to electrochemical sensor to glycerol. In all the cases the nanocomposite films presented better performances when compared to the neat Ni(OH)2 nanoparticles, showing energy and power of 43.7 W h kg-1 and 4.8 kW kg-1 (8.24 A g-1) respectively, electrochromic efficiency reaching 70 cm2 C-1 and limit of detection as low as 15.4 ± 1.2 µmol L-1.

Nickel nanoparticles with hcp structure: Preparation, deposition as thin films and application as electrochemical sensor.

Hexagonal close packed (hcp) nickel nanoparticles stabilized by polyvinylpyrrolidone (PVP) were synthesized through the thermal treatment of face centered cubic (fcc) nickel nanoparticles. Controlling both the temperature of the heat treatment and the amount of PVP was possible the control of the hcp/fcc rate in the samples, where the higher Ni/PVP ratio produces only the hcp-nickel phase (average size of 8.9 nm) highly stable in air. The crystalline structure, the presence of PVP, the size of the nanoparticles and the stability of the hcp-nickel were confirmed using X-ray diffractometry, Fourier transform infrared spectroscopy, transmission electron microscopy, Raman spectroscopy, scanning electron microscopy and thermogravimetric analysis. Thin films of hcp and fcc nickel nanoparticles were prepared through a biphasic system and deposited over indium-doped tin oxide (ITO) substrates, which were electrochemically characterized and applied as glycerol amperometric sensors in NaOH medium. Parameters as the number of cycles applied and the scan rate were evaluated and indicate that hcp nickel nanoparticles are more reactive to form Ni(OH)2 and lead to more electroactive Ni(OH)2 structure. The hcp nickel nanoparticles-modified electrode showed the best sensitivity (0.258 µA L µmol(-1)) and detection limit (2.4 µmol L(-1)) toward glycerol.

The total chemical synthesis of polymer/graphene nanocomposite films.

A versatile and room temperature synthesis of thin films of polymer/graphene is reported. Drastically differing from other methods, not only the polymer but also the graphene are completely built from their simplest monomers (thiophene and benzene) in a one-pot polymerization reaction at a liquid-liquid interface. The materials were characterized and electronic properties are presented.

Transparent and conductive thin films of graphene/polyaniline nanocomposites prepared through interfacial polymerization.

This communication reports a simple, one-pot procedure for the synthesis and processing of transparent and conductive thin films of graphene/polyaniline nanocomposites based on an interfacial polymerization. Thin films presenting transmittance of 89% and sheet resistance of 60.6 Ω sq(-1) are spontaneously obtained and can be easily transferred to suitable substrates.

V2O5 nanoparticles obtained from a synthetic bariandite-like vanadium oxide: synthesis, characterization and electrochemical behavior in an ionic liquid.

Highly stable and crystalline V(2)O(5) nanoparticles with an average diameter of 15 nm have been easily prepared by thermal treatment of a bariandite-like vanadium oxide, V(10)O(24) x 9 H(2)O. Their characterization was carried out by powder X-ray diffractometry (XRD), Fourier transform infrared (FT-IR) and Raman spectroscopies, and transmission electron microscopy (TEM). The fibrous and nanostructured film obtained by electrophoretic deposition of the V(2)O(5) nanoparticles showed good electroactivity when submitted to cyclic voltammetry in an ionic liquid-based electrolyte. The use of this film for the preparation of a nanostructured electrode led to an improvement of about 50% in discharge capacity values when compared with similar electrodes obtained by casting of a V(2)O(5) xerogel.

A simple two-phase route to silver nanoparticles/polyaniline structures.

Novel silver nanoparticles/polyaniline composites were obtained through a two-phase water/toluene interfacial reaction. We show that by rigorously controlling the reaction time, different structures of the nanocomposites can be obtained, such as a thin sheet of polyaniline around the silver nanoparticles or a polymer mass with nanoparticles homogeneously embedded within it. Samples were characterized by FT-IR, UV-vis-NIR and Raman spectroscopy, X-ray diffraction, cyclic voltammetry, TEM, and HRTEM. Conductivity and current-voltage characteristics of the nanocomposites were measured, and the results indicate that different properties result from the different structures in which the nanocomposites were formed.

Sol-gel processing of a bimetallic alkoxide precursor confined in a porous glass matrix: a route to novel glass/metal oxide nanocomposites.

In this work we present the utilization of the heterometallic alkoxide [FeCl{Ti(2)(OPr(i))(9)}] as the first sol-gel single-source precursor to achieve nanocomposites made of iron and titanium oxides incorporated into Porous Vycor Glass (PVG). The nanocomposites were prepared by the impregnation of the precursor in a PVG plate followed by hydrolysis reactions. Different samples were obtained by further thermal treatment of the hydrolyzed sample. The nanocomposites were characterized by UV-vis-NIR, Raman and EPR spectroscopies, XRD and TEM. The results indicate that the room-temperature hydrolyzed samples are formed by nanoparticles of FeOOH and brookite-TiO(2) embedded on a glassy matrix. After the heat treatment at temperatures above 900 degrees C, a pseudobrookite Fe(2)TiO(5) was formed. All samples present high transparency and homogeneity. The results showed here indicate that the sol-gel process using the single-source precursor [FeCl{Ti(2)(OPr(i))(9)}] should be a novel and efficient approach to the preparation of nanometric Fe/Ti oxides incorporated into a glassy matrix.

Influence of synthetic parameters on the size, structure, and stability of dodecanethiol-stabilized silver nanoparticles.

Metal nanoparticles (NP) are very attractive because of their size- and shape-dependent properties. A widely used preparation of ligand-stabilized metal NP is the two-phase liquid-liquid method using dodecanethiol (DT) as ligand. This work presents various procedures to synthesize dodecanethiol-capped silver NPs, all of them based on a two-phase liquid-liquid method. Small alterations in the synthetic parameters lead to dramatic modifications in the nanoparticles' average size, size distribution width, stability, and structure, as well as in their ability to self-assemble.