Evaluation of the Color Stability of Three Resin-Ceramic Materials Using a Spectrophotometer and a Digital Photography Software.

Background: Computer-aided design/computer-aided manufacturing (CAD/CAM) resin ceramics allow easier milling than glass ceramics but are suspected to be more stainable. Although Photoshop® is widely used for picture analysis, its potential for shade selection has not been properly assessed. Aim: Purpose primary: To evaluate the color stability of three CAD/CAM resin ceramics and Lithium Disilicate. Secondary: to compare the color evaluation between a spectrophotometer (Vita Easyshade compact) and Photoshop software. Materials and Methods: Three CAD/CAM resin ceramic materials (n = 10) and a fourth group of lithium disilicate were used. Half of each group were thermocycled (5°C and 55°C; 3000 cycles). All samples were immersed in colored beverages (coffee, tea and red wine) for 30 days. Values were obtained by spectrophotometry and photographs analyzed using Photoshop software. The parameters measured were CIEL*a*b, and the color difference (ΔE) was analyzed. A mixed model test was used to compare the results through time and materials (α = 0.05). The comparison between the spectrophotometer and Photoshop results was performed using the bivariate Pearson's correlation test. Results: Lithium disilicate glass ceramic exhibited less color change (ΔE = 14) than resin ceramics (15.7 < ΔE < 18.7). The least change was noted with GC Cerasmart (ΔE = 15.7) followed by Vita Enamic (ΔE = 17*) and Brilliant Crios (ΔE = 18.7*). Spectrophotometer and Photoshop values showed low correlations. Conclusions: Resin ceramics may suffer from color change in clinical use. Photoshop is technique sensitive; pictures are easily affected by the light conditions and camera settings.

Application of Tribology Concept in Dental Composites Field: A Scoping Review.

Tribology is the discipline concerning the application of friction, lubrication, and wear concepts of interacting surfaces in relative motion. A growing interest has developed in tribology application in medical biomaterials, such as resin composites used in restorative dentistry. Yet, the keywords "tribology" and "biotribology" are little applied in the pertinent publications. The aim of this scoping review was to offer an overview of tribology application in dental composites research and to identify knowledge gaps and address future research. A literature search was conducted on Pubmed and Scopus databases and the studies investigating the tribological behavior of resin composites were included for qualitative synthesis. The majority of studies on dental tribology were published in the research areas of mechanical engineering/nanotechnology and differed in several methodological aspects. The preponderant engineering approach and the lack of standardized testing make the laboratory findings poorly informative for clinicians. Future research should focus on the tribological behavior of dental materials composites by means of an integrated approach, i.e., engineering and clinical, for improving development and advancement in this field of research.

Worldwide Assessment of the Mandibular First Molar Second Distal Root and Root Canal: A Cross-sectional Study with Meta-analysis.

INTRODUCTION: This study assessed the prevalence of radix entomolaris and 2 canals at the distal aspect of mandibular first molars among different geographic regions by means of cone-beam computed tomographic imaging. METHODS: Precalibrated observers from 23 worldwide geographic locations followed a standardized screening protocol to assess 5750 cone-beam computed tomographic images of mandibular first molars (250 per region), gathering demographic data and recording the presence of radix entomolaris and a second canal at the distal aspect of teeth. Intra- and interrater reliability tests were conducted and comparisons among groups were performed using proportions and odds ratio forest plots. The significance level was set at 5%. RESULTS: The results of intra- and interrater tests were above 0.79. The prevalence of radix entomolaris varied from 0.9% in Venezuela (95% confidence interval [CI], 0%-1.9%) to 22.4% in China (95% CI, 17.2%-27.6%). Regarding the proportion of a second distal canal, it ranged from 16.4% in Venezuela (95% CI, 11.8%-21.0%) to 60.0% in Egypt (95% CI, 53.9%-66.1%). The East Asia subgroup was associated with a significantly higher prevalence of an extra distolingual root, whereas the American subgroup, the American native ethnic group, and elderly patients were linked to significantly lower percentages of a second canal at the distal aspect of teeth. No significant differences were noted between male or female patients. CONCLUSIONS: The overall worldwide prevalence rates of radix entomolaris and a second canal at the distal aspect of the mandibular first molar were 5.6% and 36.9%, respectively. The East Asia geographic region and Asian ethnic group had a higher prevalence of a second distal root.

Immediate and Delayed Bond Strength of a Multimode Adhesive to Deep Coronal Dentin Following Different Root Canal Irrigation Regimens.

PURPOSE: To investigate the effects of root canal irrigants, dentin surface treatment, and timing of the restoration on the microtensile bond strength (µTBS) of a universal adhesive to deep coronal dentin. MATERIALS AND METHODS: Ninety (90) intact molars were grouped according to the irrigation protocol: group 0 (saline, control group); group 1: 5.25% sodium hypochlorite (NaOCl), 17% ethylenediaminetetraacetic acid (EDTA) followed by 5.25% NaOCl; group 2: 18% etidronic acid (HEDP) + 5.25% NaOCl in a single mixture. Groups 1 and 2 were divided into 2 subgroups (n = = 10) according to the time of restoration: immediate (subgroup A) and after 7 days (subgroup B). Four other groups (n = 10) were created according to the dentin surface pretreatment and received an immediate restoration: group 3: 5.25% NaOCl - 17% EDTA and AH Plus Cleaner; group 4: 5.25% NaOCl - 17% EDTA and 100% ethanol; group 5: 5.25% NaOCl + 18% HEDP and AH Plus Cleaner; group 6: 5.25% NaOCl + 18% HEDP and 100% ethanol. µTBS testing was carried out for each subgroup and interfaces were analyzed through SEM. The µTBS was analyzed with Welch statistics and the post-hoc Games-Howell test for multiple comparisons (p < 0.05). RESULTS: Statistically significant differences were observed between test groups and control groups (p < 0.001), except for group 3 (p = 0.349). No significant differences were recorded between groups 1A (27.5 ± 8.7 MPa), 2A (32.6 ± 14.5 MPa) and 3 (27.3 ± 14.3 MPa). Group 6 (48.6 ± 11.6 MPa) exhibited the highest µTBS among all tested groups. For groups 1 and 2, significantly higher values were recorded for subgroups 1B (39.3 ± 7.6 MPa) and 2B (43.8 ± 8.3 MPa) compared to subgroups 1A (27.5 ± 8.7 MPa) and 2A (32.6 ± 14.5 MPa). CONCLUSION: When using NaOCl as root canal irrigant, it is advisable to delay the placement of a post-endodontic-treatment restoration.

Worldwide Prevalence of a Lingual Canal in Mandibular Premolars: A Multicenter Cross-sectional Study with Meta-analysis.

INTRODUCTION: The presence of multiple root canals is an important morphologic aspect of mandibular premolars. This study aimed to perform a worldwide analysis on the prevalence of a lingual canal in mandibular premolars and to evaluate its influence on patients' demographics in 23 countries using cone-beam computed tomographic images. METHODS: Observers from 23 countries were instructed to evaluate cone-beam computed tomographic images of 300 first and 300 second premolars (13,800 teeth) regarding the presence of a lingual canal, canal configuration, and data related to patients' ethnicity, age, and sex following a standardized screening methodology. Intra- and interrater evaluations were performed using the Cohen kappa test and intraclass correlation coefficient. Proportion and odds ratio forest plots were calculated in order to compare groups. Statistical significance was set at 5%. RESULTS: Both kappa and intraclass correlation coefficient values were above 0.60, and the percentage of agreement was 94.9% (first premolar) and 97.8% (second premolar). A significant statistical difference was observed between the worldwide proportion of a lingual canal in mandibular first (23.8%; range, 12.0%-32.7%) and second (5.3%; range, 1.0%-15.3%) premolars (P < .05). Asians and patients over 60 years old were associated with the lowest proportions of a lingual canal (P < .05), whereas Africans and younger groups were associated with the highest proportions (P < .05). The prevalence of a lingual canal in males (27.9%) was higher than females (20.0%) for the first premolar only (P < .05). Males were associated with 1.533 and 1.597 higher odds of presenting a lingual root canal in the first and second premolars, respectively. CONCLUSIONS: The worldwide proportion of a lingual root canal was 23.6% and 5.3% for the first and second premolars, respectively. Ethnicity, geographic region, age, and sex had an influence on the outcomes.

Influence of remaining tooth substance and post-endodontic restoration on fracture strength of endodontically treated maxillary incisors.

The aim is to evaluate the influence of remaining tooth substance and post-endodontic restoration on fracture strength of endodontically treated maxillary incisors. 150 maxillary central incisors were divided into three groups, Group 0, intact teeth; Group 1, removal of distal wall; Group 2, removal of mesial and distal walls, and further into two subgroups A0,A1,A2 and B0,B1,B2 according to post-endodontic restoration (post/no-post), then loaded to fracture. Interactions among variables and intergroup significance were tested with two-way ANOVA and Kruskal Wallis's tests (p≤0.05). Tukey's test was applied for multiple comparisons. Statistically significant differences were found between groups B1-A1, and B2-A2, but they were not found between B0-A0. Intragroup analysis showed statistically significant differences in both groups post/no-post with decreasing dental substance. Fiber post placement causes an increase in fracture strength and a reduction of irreparable fractures in endodontically treated maxillary central incisors that lost at least one wall.

Influence of single post, oval, and multi-post restorative techniques and amount of residual tooth substance on fracture strength of endodontically treated maxillary premolars.

PURPOSE: The aim of this study was to compare the influence of the number of coronal walls and post-endodontic restorations on the mechanical strength of 165 recently extracted endodontically treated maxillary premolars. METHODS: The teeth were divided into 3 control (no post) and 3 test groups according to the number of residual walls. Each test group was divided into subgroups according to the type of post-endodontic restoration (single, oval, and multi-post techniques). Samples were prepared conforming to the assigned subgroup. A universal loading machine applied a load parallel to the longitudinal axis of the teeth, thus simulating physiological occlusion. ANOVA and the Kruskal Wallis test were used for comparisons (P ≤ 0.05), and Tukey's test for multiple comparisons. RESULTS: For intact teeth, significant differences were found among all 3 subgroups, with single post showing the highest values. For 3 residual walls, oval post resulted in significantly lower values than single and multi-post systems. For 2 residual walls, the multi-post technique showed almost twice the resistance of oval post restorations. CONCLUSION: In oval canals the use of a single or multi-post technique increased post-and-core resistance even in intact teeth, whereas oval fiber posts showed no improvements. Multi-post design improved fracture resistance mostly in maxillary premolars lacking both marginal ridges.

Adaptation of Complete Denture Base Fabricated by Conventional, Milling, and 3-D Printing Techniques: An In Vitro Study.

AIM: The aim of this study was to compare the adaptation of complete denture base (CDB) manufactured by three different techniques: conventional, milling, and three-dimensional (3-D) printing. MATERIALS AND METHODS: A master cast was duplicated to create 60 gypsum casts. Twenty casts (n = 20) were attributed to each group. In the computer-aided design and computer-aided manufacturing (CAD/CAM) groups (milling and 3-D printing), the 40 gypsum casts reserved for these two groups were scanned. An STL file was obtained and a master CDB was designed and then fabricated according to each technique. In the conventional group, a polyvinyl siloxane putty mold was obtained from the milled CDB, and this mold was used to fabricate 20 conventional denture bases by compression molding using the silicon-gypsum technique in a bronze flask. The inner surfaces of the obtained 60 CDB were scanned and superimposed over their corresponding master cast. Deviation analyses were calculated using digital subtraction technique. Five functional areas (posterior palatal seal, anterior border seal, crest of the ridge, maxillary tuberosities, and palate) were selected to evaluate the variations in CBD adaptation. RESULTS: Based on the results and color maps of all selected regions, milling technique offers the best adaptation. The crest of ridge in the conventional technique showed the least adaptation and the posterior palatal seal in the 3-D printing technique showed the best adaptation. CONCLUSION: Within the limitations of this study, the CAD/CAM fabrication techniques seem to offer better adaptation of CDB compared to the conventional fabrication technique. Milled CDBs presented the most homogeneous distribution of adaptation, yet the 3-D printing process seems a promising techniques that needs to be addressed and perfected. CLINICAL SIGNIFICANCE: The CAD/CAM technologies can help overcome many limitations related to conventional impressions and therefore should be well investigated to improve the edentulous patient's quality of life.

Push-out Bond Strength of Fiber Posts Cemented Using New Universal Adhesives on Etched and Nonetched Intraradicular Dentin.

AIM: The aim of this study was to assess if the curing mode and the etching mode could affect the push-out bond strength of different post cementation systems using two universal adhesives. MATERIALS AND METHODS: A total of 100 single-rooted teeth were divided into Prime & Bond Elect (PBE), Prime & Bond Active (PBA), and Prime & Bond XP (PBXP) as a control. The PBE, PBA, and PBXP were used in the self-etch (SE) and etch and rinse (E&R) mode. Post cementation was performed using Core X flow used in dark-cure and in light-cure. Data were analyzed using the one-way ANOVA test and post hoc Bonferroni and Dunnet tests. The Student's t test was performed to find significance between two independent groups. RESULTS: Bond strength was significantly influenced by the adhesive strategies. The PBE and PBA obtained higher values when used in the SE mode (p < 0.001). Light-cured groups obtained significantly higher values (p < 0.001) compared to dark-cured groups. The post space region also had a significant effect on the bond strength; the apical third recorded lower values in all groups (p < 0.001). CONCLUSION: The PBA and PBE universal adhesives obtained higher PBS values when used in the SE mode and followed by the light-curing of resin cement. CLINICAL SIGNIFICANCE: Universal adhesives represent a good alternative to the conventional total-etch adhesive system for fiber post cementation. Since they perform better in SE, they would be recommendable in clinical practice, as they can be used with a simplified technique.

Evaluation Of The Effect Of Different Surface Treatments, Aging And Enzymatic Degradation On Zirconia-Resin Micro-Shear Bond Strength.

PURPOSE: The purpose of this study was to evaluate the effect of surface treatments on zirconia-resin bonding and the effect of aging on bond durability for one year. METHOD: Three hundred and twenty zirconia blocks were divided into 4 equal study groups. Group 1 (control): as-sintered, group 2: (GB): grit-blasted, group 3: (LAS): laser-etched, group 4: (SIE): selective infiltration etching. Composite cylinders were bonded to the zirconia with resin cement and ceramic primer. Aging was performed following 3 different aging protocols: thermocycling, storage in distilled water, or storage in an enzymatic esterase solution. Micro-shear bond strength test (µSBS) was recorded using a universal testing machine. µSBS values were analyzed using two-way Analysis of Variance followed by Tukey post-hoc tests. Level of significance was set at 0.05. RESULTS: GB, LAS and SIE groups showed significantly higher values when compared to control. Groups GB, LAS and SIE reported a significant decrease up to 50% in µSBS after water storage and enzymatic degradation, while control group reported a 90% decrease. Failure analysis showed mainly adhesive failure for control group, while the percentage of cohesive failure in resin cement was higher in SIE group compared to GB and LAS groups. CONCLUSION: Water aging and esterase solutions played a significant role by increasing bond degradation. A minimum of one-year water and esterase storage medium should be used to evaluate the durability of the bond between resin cement and zirconia.

Effect of different CAD-CAM materials on the marginal and internal adaptation of endocrown restorations: An in vitro study.

STATEMENT OF PROBLEM: Recent resin-based and ceramic-based computer-aided design and computer-aided manufacturing (CAD-CAM) materials have been used to restore endodontically treated teeth. Adaptation of the restoration is important for clinical success, but studies evaluating the effect of these materials on the adaptation of endocrowns are lacking. PURPOSE: The purpose of this in vitro study was to evaluate the effect of resin-based and ceramic-based materials on the marginal and internal adaptation of endocrowns. MATERIAL AND METHODS: Forty mandibular molars were divided into 4 groups (n=10); each group was restored with a different CAD-CAM material: group C: hybrid nanoceramic (Cerasmart; GC Corp), group T: fiber-composite material (Trilor; Bioloren Srl), group E: lithium disilicate glass-ceramic (IPS e.max CAD; Ivoclar Vivadent AG), and group V: zirconia-reinforced lithium silicate glass-ceramic (Vita Suprinity; VITA Zahnfabrik GmbH). A digital scan was made with an intraoral digital scanner (TRIOS 3; 3Shape A/S), and endocrowns were milled with a 5-axis milling machine (Coritec 250i; imes-icore GmbH). The replica technique and a stereomicroscope (×70) were used to measure the marginal and internal adaptation of the endocrowns at 32 points. All data were statistically analyzed using 1-way ANOVA and the Tukey honestly significant difference test (α=.05). RESULTS: Statistical tests showed significant differences among the tested groups (P<.001). The resin-based groups displayed larger discrepancies than the ceramic-based groups. The resin-based groups showed a mean marginal gap larger than the mean internal gap C (P=.009), T (P<.001), whereas the ceramic-based groups showed similar gaps, V (P=.396), E (P=.936). The largest gap was observed at the pulpal floor (P<.001). CONCLUSIONS: All materials had clinically acceptable internal and marginal gaps (≤150 µm), except for the marginal gap of the Trilor group.

Influence of Adaptation and Adhesion on the Retention of Computer-aided Design/Computer-aided Manufacturing Glass Fiber Posts to Root Canal.

AIM: The study aimed to assess the effect of friction and adhesion on the pushout bond strength of CAD/CAM fiber-reinforced composite (FRC) post and cores in comparison to prefabricated fiber posts. MATERIALS AND METHODS: Thirty extracted single-rooted premolars were divided into three groups (N = 10): CP: CAD/CAM FRC posts (Trilor, Bioloren) cemented with self-adhesive resin cement (Rely X U200, 3M) as control group. CPL: CAD/CAM FRC composite posts cemented with the same self-adhesive resin cement after lubricating the root canal with petroleum jelly (Vaseline, Unilever) to prevent adhesion. RXP: prefabricated posts cemented with self-adhesive resin cement. Specimens were subjected to thermal cycling and then to pushout tests. The mode of failure was observed using a stereomicroscope. Results were analyzed by two-way ANOVA followed by a Tukey's post hoc test for comparison, p = 0.05. RESULTS: Push-out bond strength was significantly lower in the RXP group (8.54 ± 3.35 MPa) in comparison to CP (12.10 ± 1.38 MPa), while no significant differences were concluded between the other groups. Failure was mostly adhesive for CPL and RXP and adhesive and mixed for CP. CONCLUSION: Custom made CAD/CAM posts have a positive effect on the retention of FRC posts to root canal walls while adhesion between self-adhesive cement and root dentin did not influence significantly the pushout bond strength of CAD/CAM posts to root canal. CLINICAL SIGNIFICANCE: The friction of well-adapted CAD/CAM fiber post and cores plays a predominant role in the success of post restorations of endodontically treated teeth.

Effect of Fabrication Technique and Thermal Cycling on the Bond Strength of CAD/CAM Milled Custom Fit Anatomical Post and Cores: An In Vitro Study.

PURPOSE: This study is to investigate the effect of milling custom fit anatomical post and cores from fiber reinforced composite and high-density polymer blocks using CAD/CAM technology on the bond strength to root canal dentin compared with prefabricated fiber posts, and to evaluate the influence of thermal cycling on the push out bond strength of the tested materials. MATERIALS AND METHODS: Eighty extracted single-rooted premolars, endodontically treated and prepared to receive the posts, were randomly divided into four groups (n = 20): BLC: Custom-milled fiber-reinforced composite posts and cores (Trilor, Bioloren), AMC: Custom-milled high-density polymer posts and cores (Ambarino, Creamed), BLP: Prefabricated fiber-reinforced composite posts and composite core buildups (Bioloren; Filtek Bulk Fill Posterior, 3M). The posts used have the same matrix and fiber composition as BLC, RXP: Prefabricated posts and composite core buildups (RelyX fiber post, 3M; Filtek Bulk Fill Posterior); used as a control group. All of the posts were cemented using a self-adhesive resin cement (RelyX U200, 3M). Half of the sample was randomly assigned to thermal cycling in distilled water for 6,000 cycles to simulate aging, while the other half was tested for bond strength without thermal cycling. A push-out test was conducted using a universal testing machine until failure. Bond strength values were calculated in megapascals (MPa). The mode of failure was observed using a stereo microscope. Results were analyzed by two-way ANOVA followed by a Bonferroni post hoc test for comparison. The level of significance was set at p < 0.05. RESULTS: Push-out bond strength was significantly higher (p <0.001) in the CAD/CAM post groups than in the groups with prefabricated posts regardless of the post material, while aging of the teeth did not significantly affect the push-out strength (p = 0.536). Failures were adhesive between cement and dentin for all groups except for AMC, where adhesive failure between the cement and the post was also observed. CONCLUSION: The CAD/CAM manufacturing technique was proved to ameliorate the retention of the post and cores in the root canal. Thermal cycling did not affect the bond strength of the tested groups.

Evaluation of the Adaptation and Fracture Resistance of Three CAD-CAM Resin Ceramics: An In vitro Study.

AIM: The internal fit and resistance to fracture of resin ceramics are to be evaluated compared to that of lithium disilicate as the control group. MATERIALS AND METHODS: Four groups of 20 crowns each (GC Cerasmart, Vita Enamic, Coltène Brilliant Crios, and e.max CAD) were cemented on identical metal dies. Marginal gaps were measured before cementation and load to fracture was applied after cementation, half of each group was thermodynamically aged (3,000 cycles of 5° to 55° immersion followed by 200,000 cycles of 100 N load), finally the crowns were loaded until fracture in a universal testing machine. Statistical package for social sciences (SPSS) package 23 was used for statistical work. RESULTS: Marginal gaps ranged between 68.5 ± 23.8 µm and 87 ± 29.1 µm while occlusal gaps ranged from 220.7 ± 33.3 µm to 275.5 ± 46.5 µm and were not significantly different between groups. Fracture loads ranged from 633.8 ± 127.3 N to 1596.4 ± 497.7 N with lithium disilicate glass ceramics (LDGCs) and Enamic having higher values than resin nano-ceramics (RNCs). The fracture resistance was more related to material than aging and gap value. CONCLUSION: The margin adaptation of resin ceramics was comparable to lithium disilicate with no significant difference. Lithium disilicate showed a higher resistance than resin ceramics and there was a higher resistance to fracture for polymer-infiltrated ceramic-network (PICN) than RNCs. CLINICAL SIGNIFICANCE: Resin ceramics can have marginal adaptation and fracture resistance within clinical acceptance; therefore, they can be a good chair-side solution achieved in a single appointment session.

Effect of different combinations of surface treatment on adhesion of resin composite to zirconia.

Purpose: The purpose of this laboratory study was to evaluate the effect of different surface treatment combinations on resin zirconia bonding. Materials and methods: One hundred and five pre-sintered zirconia quadrangles were prepared out of zirconia blocks, polished, then sintered and divided into five groups (n=21). Group I (control): samples were untreated, group II: grit-blasting with 50 µm alumina particles, group III: grit-blasting with 100 µm alumina particles, group IV: Er,Cr:YSGG laser, and group V: selective infiltration etching technique. Microstructural analysis was performed using scanning electron microscopy, atomic force microscopy, a diffractometer, and a profilometer. Cylinders of composite resin were luted with Panavia resin composite cementand Clearfil ceramic primer. Shear bond strength (SBS) was determined using a universal testing machine. Results: SBS results were analyzed using one-way ANOVA followed by Tukey post hoc tests for multiple comparisons. The level of significance was set to 0.05. SBS values of the studied groups II, III, IV, and V were 16.2±1.8 MPa, 15.7±3.7 MPa, 14.8±3.4 MPa, and 16.8±3.0 MPa, respectively. All values were significantly higher than the control group (10.48±1.80 MPa), but without a significant difference between them. Group III exhibited the roughest surface, and Group I had a more significantly reduced surface roughness value than any other group. Group III presented the highest significant increase of tetragonal to monoclinic phase transformation (13%). Conclusion: The use of grit-blasting with greater particles size enhanced SBS with resin composite cement, but induced a higher amount of monoclinic phase transformation. The use of primer based on adhesive monomer with the resin cement is required to enhance the bonding efficiency. The use of laser enhanced the surface roughness and the bonding ability to zirconia.

Fracture Resistance and Failure Pattern of Endodontically Treated Teeth Restored with Computer-aided Design/ Computer-aided Manufacturing Post and Cores: A Pilot Study.

AIM: To evaluate the fracture resistance and failure pattern of custom made computer-aided design & computer-aided manufacturing (CAD/CAM) post and cores using a fiber reinforced composite material (FRC) and a high-density-polymer. MATERIALS AND METHODS: Thirty extracted mandibular second premolars were selected, endodontically treated and prepared to receive the posts. The specimens were randomly divided into three groups (n = 10) according to each material: group 1 (RXP) : fiber posts (Rely X, 3M-ESPE) with composite core build-up (Filtek Bulk Fill Posterior, 3M-ESPE) as a control group; group 2 (BLC): one-piece milled post and core from fiber reinforced composite blocks (Trilor, Bioloren); and group 3 (AMC): one-piece milled post and core from hybrid ceramic disks (Ambarino, Creamed). All the posts were cemented using a self-adhesive resin cement (Rely X U200, 3M ESPE). Fracture resistance was tested using a universal testing machine, failure patterns were then observed visually and radiographically then evaluated under SEM. Data was analyzed using One-way analysis of variance (ANOVA) followed by Tamhane post-hoc test in order to determine significant differences among groups (α = 0.05). RESULTS: The mean fracture resistance values were: 426.08 ± 128.26 N for group 1 (R X P), 367.06 ± 72.34N for group 2 (BLC), and 620.02 ± 54.29N for group 3 (AMC). Statistical analysis revealed that group 3 (AMC) had the highest mean load to fracture in comparison to the other groups (p = 0.000). failures were cohesive in group 2 and 3 and mixed in group 1 with no catastrophic failures reported in all groups. CONCLUSION: All systems evaluated presented sufficient mean load-to-failure values for endodontically treated teeth restorations. CAD/CAM post and cores made from high-density-polymer showed a better performance than prefabricated fiber posts.

Marginal and internal fit of CAD/CAM fiber post and cores.

AIM: To evaluate the marginal adaptation and internal fit of milled fiber post and cores using different scanning methods. MATERIALS AND METHODS: Thirty typodont tooth models (Nissin) with pulp cavity were endodontically treated and prepared to receive 30 fabricated fiber post and cores. Three different methods of scanning were used (n = 10): an intraoral scanner (IOS) (Trios 3; 3Shape) to directly digitalize the post space (Group T) and a laboratory scanner to indirectly digitalize the resin pattern (Group RP) and the silicone impression (Group S) of the post space. All the specimens were examined using an optical microscope for the measurement of the vertical marginal discrepancy (VMD), and five in each group were scanned using microcomputed tomography (µCT) for the assessment of the VMD, the internal fit at the corner (IFC), post apex (PA), and at four horizontal cross-sections (CS1-4) inside the canal. All data were analyzed using mixed-design ANOVA, followed by pairwise testing to identify the differences (α = 0.05). RESULTS: Statistical analysis revealed that Group T was associated with the smallest cement space compared with Group RP (P = 0.001) and Group S (P < 0.001) for VMD using µCT or direct microscopy (OM) (P < 0.001). Similarly, the cement space for Group T was smaller than that of Group S (P = 0.039) when measured at the IFC (µCT), and smaller than Group RP (P = 0.025) when measured at CS1-4 (µCT), with CS1 larger than CS3 (P = 0.015). There was no significant difference at PA (P = 0.271). CONCLUSION: Better adaptation was achieved with a complete digital workflow. Scanning the resin pattern or the silicone impression introduced more variables in the digital process or milling of a one-piece fiber post and core.

Shaping effectiveness and surface topography of reciprocating files after multiple simulated uses.

This in vitro study assessed morphological changes and efficiency of reciprocating files after multiple uses. Sixty standardized Endo Training Blocks and 10 ReciprocR25 files were selected (six blocks for each file). Each file was its own control (before use vs. after each instrumentation). The instruments were used according to the manufacturer's instructions, and scanning electron microscopy was used to observe fatigue cracks, metal strips/metal flash, pitting, fretting, debris, disruption of the cutting edge, and plastic deformations after each instrumentation. The presence of seven wear variables was scored semiquantitatively by viewing micrographs collected before and after use. The prepared areas in resin blocks were calculated and compared by using AutoCAD software. The control group had significantly lower values for all wear variables except fretting and plastic deformation. The presence of fatigue cracks and metal strips/metal flash significantly differed between unused instruments and instruments used four or five times, in all observed sections. The area of instrumented Endo Training Blocks significantly differed in relation to the number of instrument uses. The Reciproc files wore progressively, and repeated use affected their shaping efficiency in simulated canals.

Effectiveness of irrigation strategies on the removal of the smear layer from root canal dentin.

The aim of this study was to evaluate the removal of the smear layer by some commonly used (needle-and-syringe irrigation, sonic activation, ultrasonically activated irrigation) and new root canal irrigation strategies (negative pressure irrigation and polymer rotary file) using a novel approach by comparing pre- and post-experimental images. Prepared root canals (n = 50) were subjected to a split tooth model and divided into 5 groups (n = 10): (1) needle-and-syringe irrigation (control); (2) sonic activation (SA); (3) negative pressure irrigation with continuous warm activated irrigation and evacuation (CWA); (4) polymer finishing file (FF); (5) ultrasonically activated irrigation (UAI). Smear layer scores and percentage of open dentinal tubules (%ODT) were evaluated by 2 examiners before and after irrigation procedures, from the middle and apical thirds of the root canal, on scanning electron microscopic images. Data were analysed using Kruskal-Wallis and post hoc tests at P = 0.05. Needle-and-syringe irrigation (control) showed no significant difference (both smear score and %ODT) compared to the pre-experimental value (P > 0.05). All other groups showed lower smear scores and higher %ODT, compared to the control (P < 0.05). The lowest smear score and highest %ODT were observed in the CWA group, which was significantly different from all other groups (P < 0.05). SA group showed significantly higher smear scores and lower %ODT than FF or UAI (P < 0.05). CWA showed superior removal of smear layer in the middle and apical thirds of the root canal compared to the other irrigation strategies.

Worldwide Analyses of Maxillary First Molar Second Mesiobuccal Prevalence: A Multicenter Cone-beam Computed Tomographic Study.

INTRODUCTION: Maxillary first molar second mesiobuccal (MB2) root canal prevalence may change among different populations. The aim of this study was to analyze the worldwide prevalence of the MB2 root canal and understand its possible relation with sex, age, side, and root configuration using in vivo cone-beam computed tomographic (CBCT) assessment. METHODS: Observers from 21 regions were calibrated to achieve a similar CBCT assessment methodology and instructed to collect data from 250 maxillary first molars in previously existing examinations. Intra- and interrater reliability tests were performed. The sample size included 5250 molars and was defined by way of a preliminary trial. Data collected included MB2 presence, sex, age, side, number of roots per tooth, and mesiobuccal root configuration. The z test for proportions in independent groups was used to analyze the differences among subgroups. P < .05 was considered significant. RESULTS: The worldwide CBCT-assessed MB2 prevalence was 73.8%, ranging from 48.0% in Venezuela to 97.6% in Belgium. The prevalence in males and females was 76.3% and 71.8%, respectively (P < .05). Significantly higher MB2 proportions were found in younger patients and 3-rooted molar configurations. The group intraclass correlation coefficient and the percentage of agreement for the MB2 presence were 0.95 and 0.91, respectively. The intrarater Cohen kappa value was above 0.61 for all observers. CONCLUSIONS: MB2 prevalence in the analyzed regions varied widely. The differences may be associated with specificities within each region but also patient demographics. Males, younger patients, and 3-rooted configurations were associated with higher MB2 proportions.