Effect of oxidation heat treatment with airborne-particle abrasion on the shear bond strength of ceramic to base metal alloys.

STATEMENT OF PROBLEM: Oxidation heat treatment has been studied to increase the metal-ceramic bond strength. However, information about its use with cobalt-chromium (Co-Cr) alloys is lacking. PURPOSE: The purpose of this study was to evaluate the effect of oxidation heat treatment and oxidation heat treatment with alumina airborne-particle abrasion on the metal-ceramic bond strength of Co-Cr alloys compared with that of nickel-chromium (Ni-Cr) alloys. MATERIAL AND METHODS: In total, 165 metal cylinders (∅5×8 mm) made of 5 base metal alloys were obtained by casting: 2 Ni-Cr (Fit Cast-SB and Fit Cast-V) and 3 Co-Cr alloys (Keragen, StarLoy C, and Remanium 2001). The specimens were divided into groups (n=11): no treatment, oxidation heat treatment, and oxidation heat treatment with airborne-particle abrasion. Oxidation heat treatment was performed starting at 650 °C and rising to 980 °C. The airborne-particle abrasion was performed with 100-µm alumina (0.2-MPa pressure, 5 seconds). One specimen had the surface topography and composition evaluated by scanning electron microscopy and energy dispersive X-ray spectrometry. The feldspathic ceramic was applied to the base metal alloy specimens (n=10). Shear tests were performed to obtain the metal-ceramic bond strength (MPa). The failure modes were evaluated. Data were evaluated by 2-way ANOVA and the Tukey post hoc test, Pearson correlation, and Fisher exact tests (α=.05). RESULTS: The group without treatment showed the highest roughness. The treatments increased oxygen and chromium levels and decreased nickel, molybdenum, and tungsten levels. Oxidation heat treatment provided an increase in metal-ceramic bond strength (P<.05) for base metal alloys with over 7% molybdenum (Fit Cast-SB, Fit Cast-V, and Remanium 2001). With oxidation heat treatment with airborne-particle abrasion, there was improvement only in Fit Cast-SB. No treatment was better for StarLoy C. A weak correlation was found between metal-ceramic bond strength and failure mode (ρ=.166; P=.043). The mixed failures were prevalent in Co-Cr alloys (P<.001) and oxidation heat treatment with airborne-particle abrasion (P=.008). CONCLUSIONS: The oxidation heat treatment was only beneficial for base metal alloy with a molybdenum content of over 7%. Although the oxidation heat treatment with alumina airborne-particle abrasion was a better treatment for Fit Cast-SB, its use is not justified because it showed no difference for oxidation heat treatment and requires another step in the surface treatment.

Antimicrobial activity of effervescent denture tablets on multispecies biofilms.

PURPOSE: To investigate the impact of peroxide-based solutions in reducing viability and metabolic activity of multispecies biofilms on denture base acrylic resin surfaces and for removing them from these surfaces. BACKGROUND: Denture cleansers are effective in reducing monospecies biofilm; however, studies evaluating their action on multispecies biofilms are scarce. MATERIALS AND METHODS: Sixty-nine denture base acrylic resin specimens (Ø 15 × 3 mm) were sterilised then contaminated with Candida albicans, Staphylococcus aureus and Pseudomonas aeruginosa to form multispecies biofilms. Biofilms were grown for 24 hours; subsequently, specimens were immersed in three different cleansing solutions (n = 9): nitradine (NI), fixodent (FX) and phosphate-buffered saline (Control), according to the respective manufacturer's instructions. After applying the hygiene protocols, viability of microorganisms was evaluated by counting colony-forming units and assessing metabolic activity. Moreover, biofilm removal capacity was estimated based on extension of cell-covered areas visualised in fluorescent microscopy micrographics. RESULTS: Microbial counts were solution-dependent; NI was effective against all microorganisms (P < .05). FX exhibited moderate antimicrobial action, reducing P aeruginosa (P < .05) and S aureus (P < .05) viability by approximately 2 logs. Both peroxide-based solutions reduced metabolic activity (P < .001) and biofilm-covered areas on specimen surfaces (P < .001). CONCLUSION: Under the experimental conditions tested, these results demonstrated that peroxide-based solutions had favourable antimicrobial activity but promoted no broad elimination of aggregated multispecies biofilm. NI might be more suitable as complementary chemical agent for controlling multispecies denture biofilm.

Effect of casting atmosphere on the marginal deficiency and misfit of Ni-Cr alloys with and without beryllium.

STATEMENT OF PROBLEM: The marginal adaptation of prosthetic crowns is still a significant clinical problem. PURPOSE: The purpose of this in vitro study was to evaluate the marginal deficiency and misfit of Ni-Cr alloys with and without beryllium under different casting conditions. MATERIAL AND METHODS: Four casting conditions were selected: flame-torch, induction/argon, induction/vacuum, and induction/air; and 2 alloys were used, Ni-Cr-Be and Ni-Cr. For each group, 10 metal specimens were prepared. Silicone indirect impressions and analysis of the degree of rounding were used to evaluate the marginal deficiencies of metal copings, and a standardized device for the setting pressure associated with optical microscopy was used to analyze the marginal misfit. Results were evaluated with 2-way ANOVA (α=.05), followed by the Tukey honest significant difference post hoc test, and the Pearson correlation test (α=.05). RESULTS: Alloy (P<.001) and casting technique (P<.001) were shown to affect marginal deficiencies. The Ni-Cr cast using the torch technique showed the highest marginal deficiency, and the Ni-Cr-Be cast in a controlled argon atmosphere showed the lowest (P<.001). Alloy (P=.472) and casting techniques (P=.206) did not affect the marginal misfit, but significant differences were found in the interaction (P=.001); the lowest misfit was achieved using the Ni-Cr-Be, and the highest misfit occurred with the molten Ni-Cr, using the cast torch technique. No correlation was found between deficiency and marginal misfit (r=.04, P=.69). CONCLUSIONS: The interactions demonstrated that the alloy containing beryllium that was cast in an argon atmosphere led to reduced marginal deficiency. Improved marginal adaptation can be achieved for the same alloy by using the torch technique.

Effect of different cleansers on the weight and ion release of removable partial denture: an in vitro study.

OBJECTIVE: Removable partial dentures (RPD) require different hygiene care, and association of brushing and chemical cleansing is the most recommended to control biofilm formation. However, the effect of cleansers has not been evaluated in RPD metallic components. The aim of this study was to evaluate in vitro the effect of different denture cleansers on the weight and ion release of RPD. MATERIAL AND METHODS: Five specimens (12x3 mm metallic disc positioned in a 38x18x4 mm mould filled with resin), 7 cleanser agents [Periogard (PE), Cepacol (CE), Corega Tabs (CT), Medical Interporous (MI), Polident (PO), 0.05% sodium hypochlorite (NaOCl), and distilled water (DW) (control)] and 2 cobalt-chromium alloys [DeguDent (DD), and VeraPDI (VPDI)] were used for each experimental situation. One hundred and eighty immersions were performed and the weight was analyzed with a high precision analytic balance. Data were recorded before and after the immersions. The ion release was analyzed using mass spectrometry with inductively coupled plasma. Data were analyzed by two-way ANOVA and Tukey HSD post hoc test at 5% significance level. RESULTS: Statistical analysis showed that CT and MI had higher values of weight loss with higher change in VPDI alloy compared to DD. The solutions that caused more ion release were NaOCl and MI. CONCLUSIONS: It may be concluded that 0.05% NaOCl and Medical Interporous tablets are not suitable as auxiliary chemical solutions for RPD care.

Effect of different cleansers on the weight and ion release of removable partial denture: an in vitro study

OBJECTIVE: Removable partial dentures (RPD) require different hygiene care, and association of brushing and chemical cleansing is the most recommended to control biofilm formation. However, the effect of cleansers has not been evaluated in RPD metallic components. The aim of this study was to evaluate in vitro the effect of different denture cleansers on the weight and ion release of RPD. MATERIAL AND METHODS: Five specimens (12x3 mm metallic disc positioned in a 38x18x4 mm mould filled with resin), 7 cleanser agents [Periogard (PE), Cepacol (CE), Corega Tabs (CT), Medical Interporous (MI), Polident (PO), 0.05 percent sodium hypochlorite (NaOCl), and distilled water (DW) (control)] and 2 cobalt-chromium alloys [DeguDent (DD), and VeraPDI (VPDI)] were used for each experimental situation. One hundred and eighty immersions were performed and the weight was analyzed with a high precision analytic balance. Data were recorded before and after the immersions. The ion release was analyzed using mass spectrometry with inductively coupled plasma. Data were analyzed by two-way ANOVA and Tukey HSD post hoc test at 5 percent significance level. RESULTS: Statistical analysis showed that CT and MI had higher values of weight loss with higher change in VPDI alloy compared to DD. The solutions that caused more ion release were NaOCl and MI. CONCLUSIONS: It may be concluded that 0.05 percent NaOCl and Medical Interporous tablets are not suitable as auxiliary chemical solutions for RPD care.

Influence of the occlusal alteration in the mandible morphology of the gerbil / Influencia de la alteración oclusal en la morfología mandibular del jerbo

Considering the biomechanical aspects, many facts need to be understood on the mandible, to know which effects unilateral occlusal changes may cause on the stomatognathic system. The aim of this study was to analyze the malocclusion by unilateral teeth extraction on the mandible morphology in gerbil. We used 10 gerbils Meriones unguiculatus, young male, weighing around 50-60g, divided into two groups (n=5), an experimental group and control, which evaluated the two hemi-mandibles, with a total of 20 samples which were measured by digital pachymeter. The measures were taken: (1) length and (2) width of the mandible condyle and (3) body height in the region of mandibular 1st molar. Data from these measurements were analyzed using ANOVA and Mann-Whitney test. The results of this study showed a statistically significant difference in the three measures between experimental and control groups. The width of the mandible head (condyle) showed statistical difference between the ipsilateral and contralateral sides to teeth extraction. It was concluded that the mastication modification by unilateral teeth extraction caused an imbalance, promoting not only a modification in the craniofacial growth pattern, but also a harmful effect on the stomatognathic system of the gerbil used as an experimental model in this study.

Considerando los aspectos biomecánicos, muchos hechos deben ser entendidos sobre la mandíbula, haciendo necesario comprender cuales son los efectos que pueden causar una alteración oclusal unilateral en el sistema estomatognático. El objetivo de este estudio fue analizar la maloclusión por la extracción de los dientes unilaterales sobre la morfología de la mandíbula en el gerbo. Se utilizaron 10 gerbos Meriones unguiculatus, machos jóvenes, con un peso aproximado de 50-60g, divididos en dos grupos (n = 5), un grupo experimental y otro control, en los cuales se evaluaron las dos hemimandíbulas, totalizando 20 muestras que fueron medidas con un caliper digital. Las medidas tomadas fueron: (1) longitud y (2) ancho del cóndilo mandibular, y (3) la altura del cuerpo en la región de los primeros molares mandibulares. Los datos de estas mediciones se analizaron mediante la prueba ANOVA y Mann-Whitney. Los resultados de este estudio mostraron una diferencia estadísticamente significativa en las tres medidas entre los grupos experimental y control. El ancho de la cabeza de la mandíbula (cóndilo) mostró una diferencia estadística entre los lados ipsilaterales y contralaterales a la extracción dentaria. Se concluyó que existe una alteración unilateral de la masticación inducida por la extracción de dientes unilateralmente, causando un desequilibrio y promoviendo no sólo una modificación en el patrón de crecimiento craneofacial, sino también un efecto nocivo obre el sistema estomatognático del gerbo utilizado como modelo experimental en este estudio.