A novel design of hip-stem with reduced strain-shielding.

The use of uncemented stems in hip arthroplasty has been increasing, even in osteoporotic patients. The major concerns of uncemented hip-stems, however, are peri-prosthetic fracture, thigh pain, and proximal femoral stress-/strain-shielding. In this study, a novel design of uncemented hip-stem is proposed that will reduce such concerns, improve osseointegration, and benefit both osteoporotic and arthritic patients. The stem has a central titanium alloy core surrounded by a set of radial buttresses that are partly porous titanium, as is the stem tip. The aim of the study was to investigate the mechanical behaviour of the proposed partly-porous design, examining load transfer in the short-term, and comparing its strain-shielding behaviour with a solid metal implant. The long-term effect of implant-induced bone remodelling was also simulated. Computed tomography based three-dimensional finite element models of an intact proximal femur, and the same femur implanted with the proposed design, were developed. Peak hip contact and major muscle forces corresponding to level-walking and stair climbing were applied. The proposed partly-porous design had approximately 50% lower strain-shielding than the solid-metal counterpart. Results of bone remodelling simulation indicated that only 16% of the total bone volume is subjected to reduction of bone density. Strain concentrations were observed in the bone around the stem-tip for both solid and porous implants; however, it was less prominent for the porous design. Lower strain-shielding and reduced bone resorption are advantageous for long-term fixation, and the reduced strain concentration around the stem-tip indicates a lower risk of peri-prosthetic fracture.

Effects of open and minimally invasive Transforaminal Lumbar Interbody Fusion (TLIF) surgical techniques on mechanical behaviour of fused L3-L4 FSU: A comparative finite element study.

For predicting the biomechanical effects of the fusion procedure, finite element (FE) analysis is widely used as a preclinical tool. Although several FE studies examined the efficacies of various fusion surgical techniques, comparative studies on Open and minimally invasive (MIS) transforaminal lumbar interbody fusion (TLIF) procedures incorporating a follower coordinate system have not been investigated yet. The current FE study evaluates the ranges of motion (ROM) and load distributions of Open-TLIF and MIS-TLIF implanted models, under physiological loading such as compression, flexion, extension and lateral bending. The most noteworthy finding from the investigation is that both the fusion procedures significantly reduced the ROMs of the implanted segment (L3-L4) and full model (L1-L5) by at least 89 % and 44 %, respectively, compared to the intact model. For all loading situations, over 95 % of the implanted models' cancellous bone volume was subjected to von Mises strains ranging from 0.0003 to 0.005. The maximum von Mises strain was observed to be localized on a small amount of cancellous bone volume (<5 %). The likelihood of adjacent segment degeneration is higher in the case of MIS-TLIF due to the higher stress (22-53 MPa) and strain (0.018-0.087) noticed on the upper facet of the L3 vertebra.

Finite element analysis of an intact lumbar spine model: Effects of loading under different coordinate systems.

Finite element (FE) analysis has been used in studying the biomechanics of the lumbar spine. While some FE studies used a follower load technique that intended to replace the compressing effect of local muscle force, other studies considered satisfying the relationship between the human body's posture and the centre of gravity (CG) for investigating spine biomechanics. However, the above studies did not reveal the importance of a coordinate system that gratifies the posture-CG relation and follower load techniques. The present FE study compares the variation in ranges of motion (ROM) and stress-strain distributions due to the application of loading via different coordinate systems, follower (FCS) and global (GCS). A subject-specific computed tomography scan-based intact spine (L1-L5) FE model was developed and simulated for physiological movements. The FE results indicated a minimum deviation in ROM of 2.7° for the L1-L5 full model at all physiological activities between the defined coordinate systems. The observed variation for the L3-L4 functional spinal unit was between 4.7° and 19°. The von Mises strain in the vertebrae was between 0.0007 and 0.003 for the FCS case. In contrast, the peak von Mises strain for the GCS case was above the compressive yield strain limit of cancellous bone by 38.5%. The GCS model transferred the load unsymmetrically, whereas the distribution was symmetrical for the FCS case, without any potential risk of bone failure. These observations clearly indicate that the selection of the appropriate loading coordinate system is as crucial as the magnitude of loading.

Patient-specific femoral implant design using metamaterials for improving load transfer at proximal-lateral region of the femur.

Loading configuration of hip joint creates resultant bending effect on femoral implants. So, the lateral side of femoral implant which is under tension retracts from peri­implant bone due to positive Poisson's ratio. This retraction of implant leads to load shielding and gap opening in proximal-lateral region, thereby allowing entry of wear particle to implant-bone interface. Retraction of femoral implant can be avoided by introducing auxetic metamaterial to the retracting side. This allows the implant to push peri­implant bone under tensile condition by virtue of their auxetic (negative Poisson's ratio) nature. To develop such implants, a patient-specific conventional solid implant was first designed based on computed-tomography scan of a patient's femur. Two types of metamaterials (2D: type-1) and (3D: type-2) were employed to design femoral meta-implants. Type-1 and type-2 meta-implants were fabricated using metallic 3D printing method and mechanical compression testing was conducted. Three finite element (FE) models of the femur implanted with solid implant, type-1 meta-implant and type-2 meta-implant were developed and analysed under compression loading. Significant correlation (R2 = 0.9821 and R2 = 0.9977) was found between the experimental and FE predicted strains of the two meta-implants. In proximal-lateral region of the femur, an increase of 7.1% and 44.1% von-Mises strain was observed when implanted with type-1 and type-2 meta-implant over the solid implant. In this region, bone remodelling analysis revealed 2.5% bone resorption in case of solid implant. While bone apposition of 0.5% and 7.7% was observed in case of type-1 and type-2 meta-implants, respectively. The results of this study indicates that concept of introduction of metamaterial to the lateral side of femoral implant can prove to provide higher osseointegration-friendly environment in the proximal-lateral region of femur.

Biomechanical and clinical studies on lumbar spine fusion surgery: a review.

Low back pain is associated with degenerative disc diseases of the spine. Surgical treatment includes fusion and non-fusion types. The gold standard is fusion surgery, wherein the affected vertebral segment is fused. The common complication of fusion surgery is adjacent segment degeneration (ASD). The ASD often leads to revision surgery, calling for a further fusion of adjacent segments. The existing designs of nonfusion type implants are associated with clinical problems such as subsidence, difficulty in implantation, and the requirement of revision surgeries. Various surgical approaches have been adopted by the surgeons to insert the spinal implants into the affected segment. Over the years, extensive biomechanical investigations have been reported on various surgical approaches and prostheses to predict the outcomes of lumbar spine implantations. Computer models have been proven to be very effective in identifying the best prosthesis and surgical procedure. The objective of the study was to review the literature on biomechanical studies for the treatment of lumbar spinal degenerative diseases. A critical review of the clinical and biomechanical studies on fusion spine surgeries was undertaken. The important modeling parameters, challenges, and limitations of the current studies were identified, showing the future research directions.

Evaluation of mechanical properties of Ti-25Nb BCC porous cell structure and their association with structure porosity: A combined finite element analysis and analytical approach for orthopedic application.

Ti-based alloys have been commonly employed in manufacturing implants for orthopedic applications. Binary Titanium-Niobium (Ti-25Nb) alloy is a promising material for potential applications in orthopedics because of their lower elastic moduli and superior biocompatibility than the conventional Ti-based alloys. Implants with porous structures encourage bone ingrowth and reduce the effect of stress-shielding further. This study is aimed at establishing the relationship between the mechanical performance and structural parameters of porous body-centered-cubic (BCC) structures made up of Ti-25Nb (25% by wt.). Solid models of BCC porous structures were constructed (unit cell size: 2 mm; overall size: 8 × 8 × 8 mm3). Finite element analysis (FEA) of the BCC structures with porosity ranging from 29% to 79% (seven porosities) was conducted under tension, bending, and torsional loads. The Gibson-Ashby model and Exponential regression model were also employed to determine the stiffness of the above porous structures. The functional relationships between effective Young's modulus, effective yield strength, and porosity generated from both the models were found to match the FEA results well. Results indicated that porosity in the range of 50%-70% can be used to design graded porous stems to mimic the mechanical properties of cortical bone.

Reduced tibial strain-shielding with extraosseous total knee arthroplasty revision system.

BACKGROUND: Revision total knee arthroplasty (RTKA) has poorer results than primary total knee arthroplasty (TKA), and the prostheses are invasive and cause strain-shielding of the bones near the knee. This paper describes an RTKA system with extracortical fixation. It was hypothesised that this would reduce strain-shielding compared with intramedullary fixation. METHODS: Twelve replica tibiae were prepared for full-field optical surface strain analysis. They were either left intact, implanted with RTKA components with cemented intramedullary fixation stems, or implanted with a novel design with a tibial tray subframe supported by two extracortical fixation plates and screw fixation. They were loaded to simulate peak walking and stair climbing loads and the surface strains were measured using digital image correlation. The measurements were validated with strain gauge rosettes. RESULTS: Compared to the intact bone model, extracortical fixation reduced surface strain-shielding by half versus intramedullary fixation. For all load cases and bone regions examined, the extracortical implant shielded 8-27% of bone strain, whereas the intramedullary component shielded 37-56%. CONCLUSIONS: The new fixation design, which offers less bone destruction than conventional RTKA, also reduced strain-shielding. Clinically, this design may allow greater rebuilding of bone loss, and should increase long-term fixation.

Femoral fracture type can be predicted from femoral structure: A finite element study validated by digital volume correlation experiments.

Proximal femoral fractures can be categorized into two main types: Neck and intertrochanteric fractures accounting for 53% and 43% of all proximal femoral fractures, respectively. The possibility to predict the type of fracture a specific patient is predisposed to would allow drug and exercise therapies, hip protector design, and prophylactic surgery to be better targeted for this patient rendering fracture preventing strategies more effective. This study hypothesized that the type of fracture is closely related to the patient-specific femoral structure and predictable by finite element (FE) methods. Fourteen femora were DXA scanned, CT scanned, and mechanically tested to fracture. FE-predicted fracture patterns were compared to experimentally observed fracture patterns. Measurements of strain patterns to explain neck and intertrochanteric fracture patterns were performed using a digital volume correlation (DVC) technique and compared to FE-predicted strains and experimentally observed fracture patterns. Although loaded identically, the femora exhibited different fracture types (six neck and eight intertrochanteric fractures). CT-based FE models matched the experimental observations well (86%) demonstrating that the fracture type can be predicted. DVC-measured and FE-predicted strains showed obvious consistency. Neither DXA-based BMD nor any morphologic characteristics such as neck diameter, femoral neck length, or neck shaft angle were associated with fracture type. In conclusion, patient-specific femoral structure correlates with fracture type and FE analyses were able to predict these fracture types. Also, the demonstration of FE and DVC as metrics of the strains in bones may be of substantial clinical value, informing treatment strategies and device selection and design. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:993-1001, 2018.

Finite element analysis of a hemi-pelvis: the effect of inclusion of cartilage layer on acetabular stresses and strain.

An appropriate method of application of the hip-joint force and stress analysis of the pelvic bone, in particular the acetabulum, is necessary to investigate the changes in load transfer due to implantation and to calculate the reference stimulus for bone remodelling simulations. The purpose of the study is to develop a realistic 3D finite element (FE) model of the hemi-pelvis and to assess stress and strain distribution during a gait cycle. The FE modelling approach of the pelvic bone was based on CT scan data and image segmentation of cortical and cancellous bone boundaries. Application of hip-joint force through an anatomical femoral head having a cartilage layer was found to be more appropriate than a perfectly spherical head, thereby leading to more accurate stress-strain distribution in the acetabulum. Within the acetabulum, equivalent strains varied between 0.1% and 0.7% strain in the cancellous bone. High compressive (15-30 MPa) and low tensile (0-5 MPa) stresses were generated within the acetabulum. The hip-joint force is predominantly transferred from the acetabulum through the lateral cortex to the sacroiliac joint and the pubic symphysis. The study is useful to understand the load transfer within the acetabulum and for further investigations on acetabular prosthesis.

The effect of primary stability on load transfer and bone remodelling within the uncemented resurfaced femur.

One of the major causes of aseptic loosening in an uncemented implant is the lack of any attachment between the implant and the bone. The implant's stability depends on a combination of primary stability (mechanical stability) and secondary stability (biological stability). The primary stability may affect the implant-bone interface condition and thus influence the load transfer and mechanical stimuli for bone remodelling in the resurfaced femur. This paper reports the results of a study into the affect of primary stability on load transfer and bone adaptation for an uncemented resurfaced femur. Three-dimensional finite element models were used to simulate the intact and resurfaced femurs and the bone remodelling. As a first step towards assessing the immediate post-operative condition, a debonded interfacial contact condition with varying levels of the friction coefficient (0.4, 0.5, and 0.6) was simulated at the implant-bone interface. Then, using a threshold value of micromotion of 50 microm, the implant-bone interfacial condition was varied along the implant-bone boundary to mechanically represent non-osseointegrated or osseointegrated regions of the interface. The considered applied loading conditions included normal walking and stair climbing. Resurfacing leads to strain shielding in the femoral head (20-75 per cent strain reductions). In immediate post-operative conditions, there was no occurrence of elevated strains in the cancellous bone around the proximal femoral neck-component junction resulting in a lower risk of neck fracture. Predominantly, the micromotions were observed to remain below 50 microm at the implant-bone interface, which represents 97-99 per cent of the interfacial surface area. The predicted micromotions at the implant-bone interface strongly suggest the likelihood of bone ingrowth onto the coated surface of the implant, thereby enhancing implant fixation. For the osseointegrated implant-bone interface, the effect of strain shielding was observed in a considerably greater bone volume in the femoral head as compared to the initial debonded interfacial condition. A 50-80 per cent peri-prosthetic bone density reduction was predicted as compared to the value of the intact femur, indicating bone resorption within the superior resurfaced head. Although primary fixation of the resurfacing component may be achieved, the presence of high strain shielding and peri-prosthetic bone resorption are a major concern.

Influence of the change in stem length on the load transfer and bone remodelling for a cemented resurfaced femur.

The effect of a short-stem femoral resurfacing component on load transfer and potential failure mechanisms has rarely been studied. The stem length has been reduced by approximately 50% as compared to the current long-stem design. Using 3-D FE models of natural and resurfaced femurs, the study is aimed at investigating the influence of a short-stem resurfacing component on load transfer and bone remodelling. Applied loading conditions include normal walking and stair climbing. The mechanical role of the stem along with implant-cement and stem-bone contact conditions was observed to be crucial. Shortening the stem length to half of the current length (long-stem) led to several favourable effects, even though the stress distributions in the implant and the cement were similar in both the cases. The short-stem implant led not only to a more physiological stress distribution but also to bone apposition (increase of 20-70% bone density) in the superior resurfaced head, when the stem-bone contact prevailed. This also led to a reduction in strain concentration in the cancellous bone around the femoral neck-component junction. The normalised peak strain in this region was lower for the short-stem design as compared to that of the long-stem one, thereby reducing the initial risk of neck fracture. The effect of strain shielding (50-75% reduction) was restricted to a small bone volume underlying the cement, which was approximately half of that of the long-stem design. Consequently, bone resorption was considerably less for the short-stem design. The short-stem design offers better prospects than the long-stem resurfacing component.

Strain and micromotion in intact and resurfaced composite femurs: experimental and numerical investigations.

Understanding the load transfer within a resurfaced femur is necessary to determine the influence of mechanical factors on potential failure mechanisms such as early femoral neck fractures and stress shielding. In this study, an attempt has been made to measure the stem-bone micromotion and implant cup-bone relative displacements (along medial-lateral and anterior-posterior direction), in addition to surface strains at different locations and orientations on the proximal femur and to compare these measurements with those predicted by equivalent FE models. The loading and the support conditions of the experiment were closely replicated in the FE models. A new experimental set-up has been developed, with specially designed fixtures and load application mechanism, which can effectively impose bending and deflection of the tested femurs, almost in any direction. High correlation coefficient (0.92-0.95), low standard error of the estimate (170-379 muepsilon) and low percentage error in regression slope (12.8-17.5%), suggested good agreement between the numerical and measured strains. The effect of strain shielding was observed in two (out of eight) strain gauges located on the posterior side. A pronounced strain increase occurred in strain gauges located on the anterior head and neck regions after implantation. Experimentally measured stem-bone micromotion and implant cup-bone relative displacements (0-13.7 microm) were small and similar in trends predicted by the FE models (0-25 microm). Despite quantitative deviations in the measured and numerical results, it appears that the FE model can be used as a valid predictor of the actual strain and stem-bone micromotion.

The effects of interfacial conditions and stem length on potential failure mechanisms in the uncemented resurfaced femur.

It is hypothesized that changes in stem length and implant-bone interfacial conditions would affect the mechanical environment within the uncemented resurfaced femur, thereby influencing potential short- and long-term failure mechanisms. This study is aimed at investigating the influence of changes in implant-bone interfacial conditions and stem length on eventual failure, using 3D FE models integrated with bone remodeling simulations. Musculoskeletal forces corresponding to normal walking and stair climbing were used as applied loading conditions. Sliding micromotions of 26-72 microm at the implant-bone interfaces for both the stem designs suggest bone ingrowth on the coated surface of the implant was likely. The initial risk of femoral neck fracture was less for the uncemented designs as compared to the cemented designs, irrespective of interfacial conditions and variation in stem length. For the uncemented variety, shortening the stem length provided only slight advantages (5%) with regard to strain shielding and bone remodeling. However, bone resorption was considerably higher when fully bonded interfaces were simulated. It may, therefore, be concluded that cementless fixation seems to be a viable alternative to cemented fixation, provided sufficient initial fixation and secondary stability through bone ingrowth into the coated surface of the implant can be achieved.

Design considerations for ceramic resurfaced femoral head: effect of interface characteristics on failure mechanisms.

Ceramic hip resurfacing may offer improved wear resistance compared to metallic components. The study is aimed at investigating the effects of stiffer ceramic components on the stress/strain-related failure mechanisms in the resurfaced femur, using three-dimensional finite element models of intact and resurfaced femurs with varying stem­bone interface conditions. Tensile stresses in the cement varied between 1 and 5 MPa. Postoperatively, 20­85% strain shielding was observed inside the resurfaced head. The variability in stem­bone interface condition strongly influenced the stresses and strains generated within the resurfaced femoral head. For full stem­bone contact, high tensile (151­158 MPa) stresses were generated at the cup­stem junction, indicating risk of fracture. Moreover, there was risk of femoral neck fracture due to elevated bone strains (0.60­0.80% strain) in the proximal femoral neck region. Stresses in the ceramic component are reduced if a frictionless gap condition exists at the stem­bone interface. High stresses, coupled with increased strain shielding in the ceramic resurfaced femur, appear to be major concerns regarding its use as an alternative material.