Insights into Electronucleation and Electrodeposition of Nickel from a Non-aqueous Solvent Based on NiCl2·6H2O Dissolved in Ethylene Glycol.

This work deals with nickel electronucleation and growth processes onto a glassy carbon electrode from NiCl2·6H2O dissolved in ethylene glycol (EG) solutions with and without 250 mM NaCl as a supporting electrolyte. The physicochemical properties of EG solutions, namely, viscosity and conductivity, were determined for different Ni(II) concentrations. From cyclic voltammetry, it was found that in the absence of the supporting electrolyte, the cathodic efficiency of Ni electrodeposition is about 88%; however, in the presence of the supporting electrolyte, the cathodic efficiency was reduced to 26% due to water (added along the supporting electrolyte) reduction on the growing surfaces of Ni nuclei. This side reaction produced both H2(g) and OH- ions. Part of the former was occluded in Ni, and the latter reacted with Ni(II) ions in EG forming passivation products such as Ni(OH)2(s). Moreover, it was shown that metallic Ni did not catalyze the EG reduction in this system. From chronoamperometry, it was shown that in the absence of the supporting electrolyte, the amount of Ni electrodeposits, for the same overpotential and time, was higher than in the presence of the supporting electrolyte. The j-t plots recorded in the latter system, for different Ni(II) concentrations, were analyzed using a model which involves a contribution due to multiple 3D nucleation and diffusion-controlled growth and another related to the simultaneous reduction of water on the Ni nuclei growing surfaces. This model allows not only the quantification of the Ni nucleation kinetic parameters but also the effective deconvolution of the individual contributions to the total current; thus, from the integration of the j-t plots of these contributions, it was demonstrated that the charge amount of each process depends on the Ni(II) concentration. Scanning electron microscopy, energy-dispersive X-ray spectroscopy, micro-Raman spectroscopy, and X-ray photoelectron spectroscopy revealed the presence of pure Ni nanoparticles electrodeposited on the electrode surface. Moreover, X-ray measurements verified the formation of a high-crystallinity face-centered cubic structure with preferred orientation growth on the ⟨111⟩ direction, which were also corroborated by the magnetic measurement performed in a physical property measurement system.

Novel electrochemical method to evaluate the antioxidant capacity of infusions and beverages, based on in situ formation of free superoxide radicals.

This work reports a new method to evaluate the antioxidant capacity of infusions and beverages, based on superoxide radicals. Radicals produced by the enzymatic reaction between acetylcholinesterase and hypoxanthine oxidized antioxidant molecules present in commercially available samples or standard solutions, which was monitored by means of cyclic voltammetry using a carbon paste electrode. The Trolox equivalent antioxidant capacity (TEAC) of red wine, coffee and green tea determined using this method were: (1.20 ± 0.06), (0.90 ± 0.02), and (0.65 ± 0.02), respectively. This method suggested TEACred wine > TEACcoffee > TEACgreen tea, which is the same as DPPH, spectrophotometric method. However, the electrochemical one proposed here is rapid and simple.

Adsorption and corrosion inhibition behaviour of new theophylline-triazole-based derivatives for steel in acidic medium.

The design and synthesis of a series of theophylline derivatives containing 1,2,3-triazole moieties are presented. The corrosion inhibition activities of these new triazole-theophylline compounds were evaluated by studying the corrosion of API 5 L X52 steel in 1 M HCl medium. The results showed that an increase in the concentration of the theophylline-triazole derivatives also increases the charge transference resistance (R ct) value, enhancing inhibition efficiency and decreasing the corrosion process. The electrochemical impedance spectroscopy under static conditions studies revealed that the best inhibition efficiencies (approx. 90%) at 50 ppm are presented by the all-substituted compounds. According to the Langmuir isotherm, the compounds 4 and 5 analysed exhibit physisorption-chemisorption process, with exception of the hydrogen 3, bromo 6 and iodo 7 substituted compounds, which exhibit chemisorption process. The corrosion when submerging a steel bar in 1 M HCl was studied using SEM-EDS. This experiment showed that the corrosion process decreases considerably in the presence of 50 ppm of the organic inhibitors. Finally, the theoretical study showed a correlation between EHOMO, hardness (η), electrophilicity (W), atomic charge and the inhibition efficiency in which the iodo 7 substituted compound presents the best inhibitor behaviour.

Electrochemical quantification of the antioxidant capacity of medicinal plants using biosensors.

The working area of a screen-printed electrode, SPE, was modified with the enzyme tyrosinase (Tyr) using different immobilization methods, namely entrapment with water-soluble polyvinyl alcohol (PVA), cross-linking using glutaraldehyde (GA), and cross-linking using GA and human serum albumin (HSA); the resulting electrodes were termed SPE/Tyr/PVA, SPE/Tyr/GA and SPE/Tyr/HSA/GA, respectively. These biosensors were characterized by means of amperometry and EIS techniques. From amperometric evaluations, the apparent Michaelis-Menten constant, Km', of each biosensor was evaluated while the respective charge transfer resistance, Rct, was assessed from impedance measurements. It was found that the SPE/Tyr/GA had the smallest Km' (57 ± 7) µM and Rct values. This electrode also displayed both the lowest detection and quantification limits for catechol quantification. Using the SPE/Tyr/GA, the Trolox Equivalent Antioxidant Capacity (TEAC) was determined from infusions prepared with "mirto" (Salvia microphylla), "hHierba dulce" (Lippia dulcis) and "salve real" (Lippia alba), medicinal plants commonly used in Mexico.

Guest-host complex formed between ascorbic acid and ß-cyclodextrin immobilized on the surface of an electrode.

This work deals with the formation of supramolecular complexes between ascorbic acid (AA), the guest, and ß-cyclodextrin (ß-CD), the host, that was first potentiodynamically immobilized on the surface of a carbon paste electrode (CPE) throughout the formation of a ß-CD-based conducting polymer (poly-ß-CD). With the bare CPE and the ß-CD-modified CPE, an electrochemical study was performed to understand the effect of such surface modification on the electrochemical response of the AA. From this study it was shown that on the modified-CPE, the AA was surface-immobilized through formation of an inclusion complex with ß-CD, which provoked the adsorption of AA in such a way that this stage became the limiting step for the electrochemical oxidation of AA. Moreover, from the analysis of the experimental voltammetric plots recorded during AA oxidation on the CPE/poly-ß-CD electrode surfaces, the Gibbs' standard free energy of the inclusion complex formed by the oxidation product of AA and ß-CD has been determined for the first time, ∆G0inclus = -36.4 kJ/mol.

Multicomponent click synthesis of new 1,2,3-triazole derivatives of pyrimidine nucleobases: promising acidic corrosion inhibitors for steel.

A series of new mono-1,2,3-triazole derivatives of pyrimidine nucleobases were synthesized by one-pot copper(I)-catalyzed 1,3-dipolar cycloaddition reactions between N-1-propargyluracil and thymine, sodium azide and several benzyl halides. The desired heterocyclic compounds were obtained in good yields and characterized by NMR, IR, and high resolution mass spectrometry. These compounds were investigated as corrosion inhibitors for steel in 1 M HCl solution, using electrochemical impedance spectroscopy (EIS) technique. The results indicate that these heterocyclic compounds are promising acidic corrosion inhibitors for steel.

Synthesis of new 1,2,3-triazole derivatives of uracil and thymine with potential inhibitory activity against acidic corrosion of steels.

Ten 1,4-disubstituted 1,2,3-triazoles were synthesized from one of 1-(azido-methyl)benzene, 1-(azidomethyl)-4-fluorobenzene, 1-(azidomethyl)-4-chlorobenzene, 1-(azidomethyl)-4-bromobenzene or 1-(azidomethyl)-4-iodobenzene, generated in situ from sodium azide and the corresponding benzyl halide, and dipropargyl uracil or dipropargyl thymine. Optimal experimental conditions were established for the conventional click chemistry. The corrosion inhibiting properties of some of these compounds, which were determined by means of an electrochemical technique, are also presented.

Kinetics and mechanism of the electrochemical formation of iron oxidation products on steel immersed in sour acid media.

From electrochemical techniques (cyclic voltammetry, potential steps, and EIS), XRD, and SEM-EDX, the kinetics and mechanism of anodic film formation applying anodic potential steps on steel immersed in sour acid media was determined. It was found, from a thermodynamic analysis, based on equilibrium phase diagrams of the system considered in this work, that iron oxidation may produce different new solid phases, depending on the applied potential, the first being the iron oxidation associated with formation of FeS((c)) species, which in turn can be reoxidized to FeS(2(c)) or even to Fe(2)O(3(c)) at higher potential values. From analysis of the corresponding experimental potentiostatic current density transients, it was concluded that the electrochemical anodic film formation involves an E(1)CE(2) mechanism, whereby the first of the two simultaneous processes were the Fe electrochemical oxidation (E(1)) followed by FeS precipitation (C) that occurs by 3D nucleation and growth limited by mass transfer reaction and FeS oxidation (E(2)) forming a mix of different stoichiometry iron sulphides and oxides. From EIS measurements, it was revealed that the anodic film's charge transfer resistance diminishes as the potential applied for its formation becomes more anodic, thus behaving poorly against corrosion.

Quantum chemical calculations on the interaction between flavonol and functional monomers (methacrylic acid and 4-vinylpyridine) in molecularly imprinted polymers.

Quantum chemical calculations were performed to characterize the interaction of the flavonol molecule (FL) with methacrylic acid (MAA) and 4-vinylpyridine (4VPy) in the formation of imprinted polymers. The polarizable continuum model (PCM) was used to gain insight on the type of interaction between the reactant molecules under vacuum conditions and in the presence of different solvents. The effect of solvent on the pre-polymerization complex formation was evaluated through the stability energy, in which chloroform behaves as the best solvent for the synthesis of the imprinted polymers since it facilitates the reaction by lowering its degree of stabilization. The reactivity was analyzed in terms of the electrostatic surface potential (ESP) and Mulliken charge. By means of these results, it has been possible to determine two potential recognition sites for the interaction of the MAA monomer and one for the 4VPy in relation to the strength of interaction with FL. In this concern, the interaction of the system FL-MAA is stronger than FL-4VPy.

Experimental correlation between the pKa value of sulfonphthaleins with the nature of the substituents groups.

This work presents the results obtained from a spectrophotometry study performed on some indicators of the sulfonphtaleins like phenol red (PR), thymol blue (TB), bromothymol blue (BTB), xylenol orange (XO) and methylthymol blue (MTB). During the first stage the acidity constants of some of the indicators were determined using the data from spectrophotometry, potentiometry and with the use of the software SQUAD. These were as follows: for the equilibrium 2H+BTB<-->H(2)BTB, log beta(2)=15.069+/-0.046 and for H+BTB<-->HBTB, log beta(1)=8.311+/-0.044. For the XO and the MTB five values were calculated for each, namely, for MTB: log beta(5)=42.035, log beta(4)=38.567+/-0.058, log beta(3)=32.257+/-0.057, log beta(2)=23.785+/-0.057, and log beta(1)=12.974+/-0.045 while for XO: log beta(5)=40.120+/-0.102, log beta(4)=35.158+/-0.062, log beta(3)=29.102+/-0.053, log beta(2)=21.237+/-0.044, and log beta(1)=11.682+/-0.044. During the second stage, a study was conducted on the effect of the substituents present in the indicators to determine the effect of different functional groups on the pK(a) value corresponding to the last indicator's dissociation.

New insights on the nature of the chemical species involved during the process of dopamine deprotonation in aqueous solution: theoretical and experimental study.

Due to dopamine's chemical structure and the fact that it has three pKa values, its deprotonation process, in aqueous solution, may involve different chemical species. For instance, the first deprotonation step, from the fully protonated dopamine molecule (H3DA+) to the neutral one (H2DA), will result in zwitterionic species if a proton from one of the OH groups in the catechol ring is lost or into a neutral species if the proton is lost from the amino group. Given that the interaction of such a product with its environment will be quite different depending on its nature, it is very important, therefore, to have an accurate knowledge of which is the dopamine chemical species that results after each deprotonation step. In order to gain a better understanding of dopamine chemistry and to establish a plausible dopamine deprotonation pathway, the optimized geometries of the aforementioned species were calculated in this work by means of the density functionals theory (B3LYP/6-311+G(d,p)) in both cases: in vacuo and with solvent effect, to assess, among other theoretical criteria, the proton affinities of the different dopamine species. This permitted us to propose the following reaction pathway: [reaction in text]. Moreover, the calculations of the chemical shift (NMR-GIAO) modeling the effect of the solvent with a continuum method (PCM) was in agreement with the 13C NMR experimental spectra, which confirmed even further the proposed deprotonation pathway.

Development of a novel nitrate-selective composite sensor based on doped polypyrrole.

The manufacture and evaluation of a novel sensor built with a composite material, highly selective to nitrate ions using doped polypyrrole as a recognition agent, are presented. When the ratio of recognition agent to graphite was optimized at 1:1, and the sensitivities found closely approached nernstian behavior. The stability times attained were less than 14 min with response times also below 20 s. Batch characterization of the sensor displayed a sensitivity of 57.1 mV/decade of nitrate ion activity (alphaNO3-) and a detection limit of 5.37 x 10(-5) M, which are comparable to those reported for commercial sensors. Evaluation of the selectivity coefficients showed high affinity to nitrate ion, superior to that of commercial sensors and others reported in the literature. The composite material gives the sensor a prolonged service life with the added capability of allowing the regeneration of its active surface. Coupling the sensor and a solid state, composite-type, reference electrode to a flow injection analysis system (FIA) permitted to achieve an effective overall assessment of the system. A nitrate determination test was conducted on real samples. A comparison of the results obtained, either with stationary measurements or with FIA, indicated that there were no significant differences from the values from manufacturer's specifications.

Mercury ions removal from aqueous solution using an activated composite membrane.

This work presents the results concerning the first use of activated composite membranes (ACMs) for the removal of Hg(II) ions from aqueous solution, using as the ligand di-(2-ethylhexyl)dithiophosphoric acid (DTPA). The effects on the removal percentage of Hg(ll) of variables such as pH, the nature of the acid, the concentration of mercury (in the feed solutions), and the ligand content (in the membrane) as well as the total surface membrane area exposed to the Hg(II) aqueous solution were studied. During the course of the removal experiments, the membrane was immersed in the Hg(II) aqueous solution in acid media and samples of the solution were taken at different times to enable monitoring of the mercury concentration changes. Itwasfound that when the ACM was prepared with a 1.0 M DTPA casting solution and the feed solution contained 2.49 x 10(-4) M Hg(II) in HCI 0.1 M the amount of mercury extracted was higher than 93%. Straight forwardly, additional experiments were carried out with the free-DTPA composite membranes to make up a set of control reference points to verify that removal of the investigated heavy metal was a consequence of the presence of the organic ligand; otherwise there was no Hg(II) concentration variation at all.