RESUMO
Composites are materials that are widely used in industry, including yachting, railway and aviation. The properties of these materials can be modified by changing the type of reinforcement, the type of matrix, as well as the use of additives in the form of fillers and nanofillers that improve their mechanical or specific parameters. Due to the fact that these materials are often used for important structures, computational models using FEM tools may not be sufficient to determine the actual strength parameters, and what is more, to check them during operation. When designing structures made of composite materials, it is necessary to use high safety factors due to their behavior under several different types of loads, which is still difficult to determine precisely. This situation makes these structures much heavier and characterized by much higher strength properties than those that would actually be needed. In this article, the Kolmogorov-Sinai (K-S) metric entropy was used to determine the transition from the elastic to the viscoelastic state in GFRP (glass fiber reinforced polymer) composite materials without and with the addition of nanoaluminum, during a static tensile test. Additionally, the acoustic emission method was used during the research. This signal was further processed, and graphs were made of the number of events and the amplitude as a function of time. The obtained values were plotted on tensile graphs. The influence of the nano-filler on these parameters was also analyzed. The presented results show that it is possible to determine additional parameters affecting the strength of the structure for any composite materials.
RESUMO
Batychron is a flexible underwater bell patented by the Gdynia Maritime University as a device used in hydro-technics engineering for underwater transport and diving while maintaining the safety of human life. This study aims to present the methods and results of strength tests and the conducted analysis of the selection of the most appropriate method of joining thermoplastic polyurethane film (TPU) and polypropylene belts for underwater use to obtain a device with a specific buoyancy force. A universal testing machine with a hydraulic drive was used for the tests. Various methods of joining polypropylene belts were tested to select the most favourable in terms of strength properties. For this purpose, two types of materials were selected: the TE324 polyester belt and the TS501_50 style belt. Various connection methods have been used: without seams; zig-zag stitch, straight cross; cross stitch, straight longitudinal; cross stitch, straight transverse, in order to select a joint with the highest strength parameters. In addition, the tensile strength of individual types of belts was tested. The methods of joining the TPU film were verified. The obtained results allowed us to determine that the strongest bond of TE324 material is a straight, longitudinal cross stitch. This is related to the load distribution in the belts tested in laboratory conditions, but also reflected in their practical application. Thanks to the results obtained, it was possible to select the optimal methods of joining (connection) and the construction of Batychron.
RESUMO
Polymer composites are materials that are used in many industries. Their wide application has a direct impact on the amount of post-production and post-consumer waste. The global problem with recycling, especially of fiber-reinforced polymeric materials, has prompted research into methods of their use. Previous research on composite materials with polyester-glass recyclate showed a decrease in mechanical properties. The construction material should have the highest mechanical properties. Based on the literature, it was found that the use of nanoadditives may have a positive effect on the parameters of the materials. The use of gamma aluminum nanopowder, in a small amount can significantly increase the mechanical properties of composites with polyester-glass recyclate, and thus can affect the application of these materials to structural elements. The article is devoted to the research on the hardness of composite materials with polyester-glass recyclate and gamma aluminum nanopowder. The main goal is to investigate the possibility of using a nanoadditive as a material, increasing the mechanical properties of composites with polyester-glass recyclate, so as to create a recycled material with the highest possible strength parameters. Hardness tests were performed using the Barcol method. For each composite material, 30 measurements were made in order to subject the results to a statistical analysis. Using parametric statistical tests it was shown that the obtained hardness values at the assumed level of statistical significance pv = 0.05 for comparisons for the samples of the reference material (B0) do not differ by chance, while for the comparisons in the configurations of the reference material (B0) with the modified materials, (R10, A2, R10A2) they do not differ by accident. Studies have shown that the addition of 2% gamma aluminum nanopowder slightly lowers the hardness of a pure polyester-glass composite, but the same additive allows the hardness of composite materials to be increased with the addition of glass recyclate. This is of particular importance for the development of the optimal composition of polyester-glass composites with the addition of recyclate, which will have good strength properties and at the same time enable the reuse of composite waste.
RESUMO
Composite materials are used in many industries. They are construction materials that are being used more and more often, which makes it necessary to accurately identify the process of their destruction. Recent decades have resulted in an intensive increase in diagnostic tests of structures and mechanical elements. Non-destructive testing (NDT) represents a group of test methods (surface and volumetric) that provide information about the properties of the tested element without changing its structure. The method of acoustic emission (AE) is also being used more frequently. Thanks to the ability to detect and locate signal sources, as well as to perform tests during operation, it is a method that is increasingly used in industry. In this article, the acoustic emission was used to analyze the changes occurring in composite materials. Obtained parameters helped to determine the signals originating from fibre delamination, fibre cracking, etc., as well as the starting point of these changes and the stress values at which these changes occurred. The analysis of acoustic emission signals recorded during the tests helped to determine the values of amplitudes characteristic for the destruction mechanisms of considered composite materials. Signals with an amplitude in the range of 30-41 dB may indicate elastic-plastic deformation of the matrix. Signals with an amplitude in the range of 42-50 dB indicate matrix cracks with the accompanying phenomenon of fibre delamination. Signals with amplitudes greater than 50 dB indicate fibre breakage. Based on the test results, the permissible stress was determined; when exceeded, the mechanisms of damage to the structure of composite materials accumulate. This stress limit for the tested material is 70 MPa. The use of the acoustic emission method in mechanical tests may contribute to a greater knowledge of composite materials used as a construction material, as well as determine the stresses allowable for a given structure.
RESUMO
Due to the unique properties of polymer composites, these materials are used in many industries, including shipbuilding (hulls of boats, yachts, motorboats, cutters, ship and cooling doors, pontoons and floats, torpedo tubes and missiles, protective shields, antenna masts, radar shields, and antennas, etc.). Modern measurement methods and tools allow to determine the properties of the composite material, already during its design. The article presents the use of the method of acoustic emission and Kolmogorov-Sinai (K-S) metric entropy to determine the mechanical properties of composites. The tested materials were polyester-glass laminate without additives and with a 10% content of polyester-glass waste. The changes taking place in the composite material during loading were visualized using a piezoelectric sensor used in the acoustic emission method. Thanks to the analysis of the RMS parameter (root mean square of the acoustic emission signal), it is possible to determine the range of stresses at which significant changes occur in the material in terms of its use as a construction material. In the K-S entropy method, an important measuring tool is the extensometer, namely the displacement sensor built into it. The results obtained during the static tensile test with the use of an extensometer allow them to be used to calculate the K-S metric entropy. Many materials, including composite materials, do not have a yield point. In principle, there are no methods for determining the transition of a material from elastic to plastic phase. The authors showed that, with the use of a modern testing machine and very high-quality instrumentation to record measurement data using the Kolmogorov-Sinai (K-S) metric entropy method and the acoustic emission (AE) method, it is possible to determine the material transition from elastic to plastic phase. Determining the yield strength of composite materials is extremely important information when designing a structure.
RESUMO
This study analyzes the possibility of applying the acoustic emission method (AE) and the Kolmogorov-Sinai (K-S) metric entropy phenomenon in determining the structural changes that take place within the EN AW 7020 aluminum alloy. The experimental part comprised of a static tensile test carried out on aluminum alloy samples, and the simultaneous recording of the acoustic signal generated inside the material. This signal was further processed and diagrams of the effective electrical signal value (RMS) as a function of time were drawn up. The diagrams obtained were applied on tensile curves. A record of measurements carried out was used to analyze the properties of the material, applying a method based on Kolmogorov-Sinai (K-S) metric entropy. For this purpose, a diagram of metric entropy as a function of time was developed for each sample and applied on the corresponding course of stretching. The results of studies applying the AE and the K-S metric entropy method show that K-S metric entropy can be used as a method to determine the yield point of the material where there are no pronounced yield points.
RESUMO
UNLABELLED: Prevalence of Internet use indicates, that introducing internet to people with mental disorders might have a positive impact on their social integration. There are concerns about negative effects of dealing with virtual reality on the mental health of Internet users. AIM: Evaluation of the ICAR program--"Internet communication and active rehabilitation for people with mental disorders" concerning its utility in psychiatric rehabilitation. METHOD: 22 participants of the ICAR programme and 22 controls (people with mental disorders not participating in the programme) were investigated before and after the completion of the programme. There following were compared: their computer and Internet use skills, social functioning (Birchwood Scale), self-estimation of the mental health (Frankfurt Scale FBS), self-reported quality of life (WHO QOL BREV) and number of psychiatric hospitalisations during 11 months of the observation period. RESULTS: Among participants, their reported skills and motivation increased significantly following the programme. During 11 months of the observation there were less hospitalisations (1 fulltime and 1 daily) in the study group than in the control group (3 and 1). An increase of symptoms was observed in the Frankfurt Scale in 10 participants and 13 controls. The level of social functioning and severity of symptoms was not significantly different and did not change during observation. The self-reported quality of life increased in both groups during this period. CONCLUSIONS: ICAR training programme for the mentally ill, increases participants skills and motivation towards computer and Internet use, as well as their self-reported quality of life. The participation in the programme doesn't have any significant effect on the overall social functioning and number of psychiatric hospitalisations during the 11 months of observation. A positive effect of the ICAR programme on the quality of life, as well as some activating effect leading to exacerbation of the psychopatological symptoms--has an unspecific character and is therefore similar to the other community rehabilitation programmes. Wider spreading of computer training workshops similar to the ICAR programme might have a positive effect on social integration of people with mental disorders.