Molecular Sieves for the Separation of Hydrogen Isotopes.

Stable molecular hydrogen isotopes, D2 and T2, are both scarce and essential in several energy, industrial, and large-scale fundamental research applications. Due to the chemical similarity of these isotopes, their extraction and purification from hydrogen has relied for decades on expensive and energy-demanding processes. However, factoring in the phenomenon of quantum sieving could provide a new route for these separations. In this work, we have explored how to separate hydrogen isotopes by adsorption taking these quantum effects into account. To this end, we have conducted adsorption measurements to test our deuterium model and performed a widespread computational screening over 210 pure-silica zeolites for D2/H2 and T2/H2 separations. Based on low-coverage adsorption properties, a reduced set of zeolites have been singled out and their performance in terms of adsorption capacity, selectivity, and dynamic behavior have been assessed. Overall, the BCT-type zeolite clearly stands out for highly selective separations of both D2 and T2 over H2, achieving the highest reported selectivities at cryogenic temperatures. We also identified other interesting zeolites for the separation of hydrogen isotopes that offer an alternative way to tackle similar isotopic separations by an aimed selection or design of porous materials.

Tailoring the textural properties of an activated carbon for enhancing its adsorption capacity towards diclofenac from aqueous solution.

A series of activated carbons (ACs) were prepared by modifying a commercial AC by physical activation using CO2 during different activation times. The ACs were designated as F, F12, F24, and F40 corresponding to the activation times of 0, 12, 24, and 40 h, respectively. The surface area, total pore volume, micropore volume, and mean micropore width were determined for all the ACs. The textural properties of the modified ACs increased substantially with the activation time, and the capacity of the ACs for adsorbing diclofenac (DCF) was almost linearly dependent upon the surface area of the ACS. The maximum adsorption capacities of F, F12, F24, and F40 carbons towards diclofenac (DCF) from aqueous solution were 271, 522, 821, and 1033 mg/g, respectively. Hence, the adsorption capacities of ACs were considerably enhanced with the activation time, and F12, F24, and F40 carbons presented the highest adsorption capacities towards DCF reported in the technical literature. The F40 adsorption capacity was at least twice those of other carbon materials. The adsorption capacities decreased by raising the pH from 7 to 11 due to electrostatic repulsion between the ACs surface and anionic DCF in solution. The removal of DCF from a wastewater treatment plant (WWTP) effluent was effectively carried out by adsorption on F40. Hence, the capacity of ACs for adsorbing DCF can be optimized by tailoring the porous structure of ACs.

The ability of a fibrous titanium oxophosphate for nitrogen-adsorption above room temperature.

Ti2O(PO4)2·2H2O (1), a three-dimensional titanium oxophosphate, thermally transforms to Ti2O(PO4)2 (2), a fibrous novel compound. The crystal structure of 2 was solved ab initio using powder X-ray diffraction data (triclinic, P1[combining macron], a = 5.0843(1) Å, b = 8.6121(2) Å, c = 9.6766(2) Å, α = 74.501(2)°, ß = 76.146(2)°, γ = 74.488(3)°, Z = 2). Compound 2, containing both 4- and 6-fold coordinated titanium atoms, shows measurable thermally activated nitrogen-adsorption. To our knowledge, the process described here constitutes the first example of nitrogen-fixation by an inorganic material at above-ambient temperature.

Incorporation of zeolitic imidazolate framework (ZIF-8)-derived nanoporous carbons in methacrylate polymeric monoliths for capillary electrochromatography.

A series of metal organic frameworks-derived nanoporous carbons originating from zeolitic imidazolate framework-8 (ZIF-8) crystals as precursors have been prepared via varying the preparation conditions. The ZIF-8-derived carbons were subsequently admixed in the methacrylate monomers containing polymerization mixtures and polymerized to obtain monolithic columns for capillary electrochromatography (CEC). The effect of particle size and content of the ZIF-8-derived carbon materials in the polymerization mixture on the performance of the hybrid monolithic columns was investigated in detail. The resulting composites were characterized using scanning electron microscopy. Using short time UV-initiated polymerization, monolithic beds with homogenously dispersed ZIF-8-derived carbons were obtained. The chromatographic performance of these composites was demonstrated with separations of polycyclic aromatic hydrocarbons and non-steroidal anti-inflammatory drugs as test solutes. The incorporation of the ZIF-8-derived carbons into the organic polymer monoliths led to an increase in the retention of all the analytes compared to the parent monolith. Finally, the hybrid monolithic columns exhibited satisfactory run-to-run and batch-to-batch reproducibility.

Nanoparticle-Directed Metal-Organic Framework/Porous Organic Polymer Monolithic Supports for Flow-Based Applications.

A two-step nanoparticle-directed route for the preparation of macroporous polymer monoliths for which the pore surface is covered with a metal-organic framework (MOF) coating has been developed to facilitate the use of MOFs in flow-based applications. The flow-through monolithic matrix was prepared in a column format from a polymerization mixture containing ZnO-nanoparticles. These nanoparticles embedded in the precursor monolith were converted to MOF coatings via the dissolution-precipitation equilibrium after filling the pores of the monolith with a solution of the organic linker. Pore surface coverage with the microporous zeolitic imidazolate framework ZIF-8 resulted in an increase in surface area from 72 to 273 m2 g-1. Monolithic polymer containing ZIF-8 coating was implemented as a microreactor catalyzing the Knoevenagel condensation reaction and also in extraction column format enabling the preconcentration of trace levels of toxic chlorophenols in environmental waters. Our approach can be readily adapted to other polymers and MOFs thus enabling development of systems for flow-based MOF applications.

Metal Oxide Assisted Preparation of Core-Shell Beads with Dense Metal-Organic Framework Coatings for the Enhanced Extraction of Organic Pollutants.

Dense and homogeneous metal-organic framework (MOF) coatings on functional bead surfaces are easily prepared by using intermediate sacrificial metal oxide coatings containing the metal precursor of the MOF. Polystyrene (PS) beads are coated with a ZnO layer to give ZnO@PS core-shell beads. The ZnO@PS beads are reactive in the presence of 2-methylimidazole to transform part of the ZnO coating into a porous zeolitic imidazolate framework-8 (ZIF-8) external shell positioned above the internal ZnO precursor shell. The obtained ZIF-8@ZnO@PS beads can be easily packed in column format for flow-through applications, such as the solid-phase extraction of trace priority-listed environmental pollutants. The prepared material shows an excellent permeance to flow when packed as a column to give high enrichment factors, facile regeneration, and excellent reusability for the extraction of the pollutant bisphenol A. It also shows an outstanding performance for the simultaneous enrichment of mixtures of endocrine disrupting chemicals (bisphenol A, 4-tert-octylphenol and 4-n-nonylphenol), facilitating their analysis when present at very low levels (<1 µg L(-1) ) in drinking waters. For the extraction of the pollutant bisphenol A, the prepared ZIF-8@ZnO@PS beads also show a superior extraction and preconcentration capacity to that of the PS beads used as precursors and the composite materials obtained by the direct growth of ZIF-8 on the surface of the PS beads in the absence of metal oxide intermediate coatings.

Role of crystal size on swing-effect and adsorption induced structure transition of ZIF-8.

The flexibility and structure transition behaviour of ZIF-8 in a series of samples with different particle size has been studied using a combination of high-resolution N2 gas adsorption isotherms and, for the first time, a broad in situ PXRD and Rietveld analysis. During the stepped adsorption process, large particles showed a narrow adsorption/desorption pressure range with a shorter equilibrium time due to lower kinetic hindrance, deriving from higher amount of active sites. In situ PXRD showed that both the rotation of imidazole ring and a bend in the methyl group led to the gate opening of ZIF-8.

A rapid microwave-assisted synthesis of a sodium-cadmium metal-organic framework having improved performance as a CO2 adsorbent for CCS.

We report on a facile and rapid microwave-assisted method for preparing a sodium-cadmium metal-organic framework (having coordinatively unsaturated sodium ions) that considerably shortens the conventional synthesis time from 5 days to 1 hour. The obtained (Na,Cd)-MOF showed an excellent volumetric CO2 adsorption capacity (5.2 mmol cm(-3) at 298 K and 1 bar) and better CO2 adsorption properties than those shown by the same metal-organic framework when synthesized following a more conventional procedure. Moreover, the newly prepared material was found to display high selectivity for adsorption of carbon dioxide over nitrogen, and good regenerability and stability during repeated CO2 adsorption-desorption cycles, which are the required properties for any adsorbent intended for carbon dioxide capture and sequestration (CSS) from the post-combustion flue gas of fossil fuelled power stations.

Design and development of a controlled pressure/temperature set-up for in situ studies of solid-gas processes and reactions in a synchrotron X-ray powder diffraction station.

A novel set-up has been designed and used for synchrotron radiation X-ray high-resolution powder diffraction (SR-HRPD) in transmission geometry (spinning capillary) for in situ solid-gas reactions and processes in an isobaric and isothermal environment. The pressure and temperature of the sample are controlled from 10(-3) to 1000 mbar and from 80 to 1000 K, respectively. To test the capacities of this novel experimental set-up, structure deformation in the porous material zeolitic imidazole framework (ZIF-8) by gas adsorption at cryogenic temperature has been studied under isothermal and isobaric conditions. Direct structure deformations by the adsorption of Ar and N2 gases have been observed in situ, demonstrating that this set-up is perfectly suitable for direct structural analysis under in operando conditions. The presented results prove the feasibility of this novel experimental station for the characterization in real time of solid-gas reactions and other solid-gas processes by SR-HRPD.

Assessment of the role of micropore size and N-doping in CO2 capture by porous carbons.

The role of micropore size and N-doping in CO2 capture by microporous carbons has been investigated by analyzing the CO2 adsorption properties of two types of activated carbons with analogous textural properties: (a) N-free carbon microspheres and (b) N-doped carbon microspheres. Both materials exhibit a porosity made up exclusively of micropores ranging in size between <0.6 nm in the case of the pristine materials and up to 1.6 nm for the highly activated carbons (47% burnoff). The N-doped carbons possess ~3 wt % of N heteroatoms that are incorporated into several types of functional groups (i.e., pyrrole/pyridone, pyridine, quaternary, and pyridine-N-oxide). Under conventional operation conditions (i.e., T ~ 0-25 °C and P(CO2) ~ 0-1 bar), CO2 adsorption proceeds via a volume-filling mechanism, the size limit for volume-filling being ~0.7-0.8 nm. Under these circumstances, the adsorption of CO2 by nonfunctionalized porous carbons is mainly determined by the volume of the micropores with a size below 0.8 nm. It was also observed that the CO2 capture capacities of undoped and N-doped carbons are analogous which shows that the nitrogen functionalities present in these N-doped samples do not influence CO2 adsorption. Taking into account the temperature invariance of the characteristic curve postulated by the Dubinin theory, we show that CO2 uptakes can be accurately predicted by using the adsorption data measured at just one temperature.

Waste-derived activated carbons for removal of ibuprofen from solution: role of surface chemistry and pore structure.

The removal of a widespread used drug (i.e., ibuprofen) from water was investigated using high valuable carbon adsorbents obtained from chemical and physical activation of a bioresource (cork) and a municipal waste (plastic). The waste-derived carbons outperformed the adsorption capacity of commercial carbonaceous adsorbents due to their adequate features for the removal of the targeted compound. Regarding the adsorption mechanism, the results obtained point out that ibuprofen retention is favored in activated carbons with basic surface properties. On the other hand, the textural features also play an important role; the presence of a transport pores network (i.e., mesopores) is crucial to ensure the accessibility to the inner porosity, and the microporosity must be large enough to accommodate the ibuprofen molecule. Specifically, adsorbents with a large fraction of ultramicropores (pore widths <0.7 nm) are not adequate to effectively remove ibuprofen.

Adsorption of naphthalene from aqueous solution on activated carbons obtained from bean pods.

The preparation of activated carbons from bean pods waste by chemical (K(2)CO(3)) and physical (water vapor) activation was investigated. The carbon prepared by chemical activation presented a more developed porous structure (surface area 1580 m(2) g(-1) and pore volume 0.809 cm(3) g(-1)) than the one obtained by water vapor activation (258 m(2) g(-1) and 0.206 cm(3) g(-1)). These carbons were explored as adsorbents for the adsorption of naphthalene from water solutions at low concentration and room temperature and their properties are compared with those of commercial activated carbons. Naphthalene adsorption on the carbons obtained from agricultural waste was stronger than that of carbon adsorbents reported in the literature. This seems to be due to the presence of large amounts of basic groups on the bean-pod-based carbons. The adsorption capacity evaluated from Freundlich equation was found to depend on both the textural and chemical properties of the carbons. Naphthalene uptake on biomass-derived carbons was 300 and 85 mg g(-1) for the carbon prepared by chemical and physical activation, respectively. Moreover, when the uptake is normalized per unit area of adsorbent, the least porous carbon displays enhanced naphthalene removal. The results suggest an important role of the carbon composition including mineral matter in naphthalene retention. This issue remains under investigation.

Guest-induced modification of a magnetically active ultramicroporous, gismondine-like, copper(II) coordination network.

A novel ultramicroporous coordination polymer, namely [Cu(F-pymo)2(H2O)1.25]n (1, F-pymo = 5-fluoropyrimidin-2-olate), has been prepared and structurally characterized. 1 displays a zeolitic gismondine (GIS) topology, with ca. 2.9 A wide helical channels which, in the thermally activated counterpart (1'), account for a 13% void volume and are responsible for the observed selective solid-gas adsorption properties toward H2, N2, and CO2. At 77 K 1' behaves as a molecular sieve, selectively adsorbing H2 over N2, possibly due to size-exclusion reasons. At variance, although CO2 molecules are slightly larger than the pore size, they are readily incorporated by 1' at temperatures as high as 433 K. Variable-temperature X-ray powder diffraction (TXRPD) studies, in the temperature range 303-473 K, show that dehydration is reversible and has almost negligible effects on the network. At variance, the uptake of CO2 occurs through a transient phase and channels expansion. While the gas storage capacity of 1' is not very high-H2, 0.56 wt % and 0.010 kg H2/L at 90 K and 900 Torr, and CO2, 7.6 wt % at 273 K and 900 Torr-the guest molecules achieve very high densities, comparable to that of the liquid for H2 (0.023 vs 0.021 molecules A-3) and to that of the solid for CO2 (0.014 vs 0.022 molecules A-3). In addition, we have also studied the effect of the perturbation exerted by the guest molecules on its magnetic properties. The results show that while dehydration of 1 has negligible effect on its spin-canted antiferromagnetic behavior, CO2 incorporation in the pores is responsible for an increment of the transition temperature at which the weak ferromagnetic ordering takes place from 22 to 29 K.

Role of surface adsorption and porosity features in the molecular recognition ability of imprinted sol-gels.

Organically modified molecularly imprinted silicas (MIS) for nafcillin recognition were prepared using a simple sol-gel procedure. Molecular recognition of the template was observed by tuning the chemical and structural properties of the MIS. The relative amounts of organically modified alkoxysilane precursors were found to be key in the textural and morphological characteristics of the MIS as well as for developing an imprinting effect in the materials. The recognition properties of the imprinted materials were found to be strongly influenced by the hydrolytic stability of the alkoxysilanes and their inductive effects during sol-gel hydrolysis/condensation stages. The concept was to combine properties of organic groups with those of glass-like materials in order to develop synergetic properties through variations in the composition. Results from batch rebinding experiments as well as from the thorough study of the N(2) adsorption properties and the textural and structural characteristics of the MIS revealed that an imprint effect could be attributed to the presence of the template during the synthesis of MIS.

H2, N2, CO, and CO2 sorption properties of a series of robust sodalite-type microporous coordination polymers.

H2, N2, CO, and CO2 are readily incorporated in the porous, 3D sodalitic frameworks of coordination polymers of the [ML2]n type, with M = Pd(II) or Cu(II) and HL = 2-hydroxypyrimidine or 4-hydroxypyrimidine. The metal ion and ligand functionalization modulate their sorption properties, making these materials suitable for gas storage and separation purposes.