Improved Electrophoretic Deposition of Vertical Single Wall Carbon Nanotubes with Nanoscopic Electrostatic Lenses.

Under certain conditions, electrophoretic deposition (EPD) of single-wall carbon nanotubes (SWCNTs) onto metal at the base of nanoscale insulating windows can result in a single SWCNT per window, bonded at one end to the metal. During EPD charge, buildup on the insulator creates electrostatic lenses at the windows that control the trajectory of the SWCNTs. The aim is to develop a reproducible process for deposition of individual vertically oriented SWCNTs into each window to enable novel devices. The length of the SWCNTs is shown to be the most critical parameter in achieving results that could be used for devices. In particular, single nanotube deposition in windows by EPD was achieved with SWCNTs with lengths on the order of the window depth. By performing current vs voltage (IV) measurements against a platinum wire in a phosphate buffer and by modeling the data, the presence of the nanotube can be detected, the contact interface can be studied, and the nanotube's viability for device applications can be determined. These results provide a basis for process integration of vertical SWCNTs using EPD.

Catalysis on singly dispersed bimetallic sites.

A catalytic site typically consists of one or more atoms of a catalyst surface that arrange into a configuration offering a specific electronic structure for adsorbing or dissociating reactant molecules. The catalytic activity of adjacent bimetallic sites of metallic nanoparticles has been studied previously. An isolated bimetallic site supported on a non-metallic surface could exhibit a distinctly different catalytic performance owing to the cationic state of the singly dispersed bimetallic site and the minimized choices of binding configurations of a reactant molecule compared with continuously packed bimetallic sites. Here we report that isolated Rh1Co3 bimetallic sites exhibit a distinctly different catalytic performance in reduction of nitric oxide with carbon monoxide at low temperature, resulting from strong adsorption of two nitric oxide molecules and a nitrous oxide intermediate on Rh1Co3 sites and following a low-barrier pathway dissociation to dinitrogen and an oxygen atom. This observation suggests a method to develop catalysts with high selectivity.

How strain affects the reactivity of surface metal oxide catalysts.

Highly dispersed molybdenum oxide supported on mesoporous silica SBA-15 has been prepared by anion exchange resulting in a series of catalysts with changing Mo densities (0.2-2.5 Mo atoms nm(-2) ). X-ray absorption, UV/Vis, Raman, and IR spectroscopy indicate that doubly anchored tetrahedral dioxo MoO4 units are the major surface species at all loadings. Higher reducibility at loadings close to the monolayer measured by temperature-programmed reduction and a steep increase in the catalytic activity observed in metathesis of propene and oxidative dehydrogenation of propane at 8 % of Mo loading are attributed to frustration of Mo oxide surface species and lateral interactions. Based on DFT calculations, NEXAFS spectra at the O-K-edge at high Mo loadings are explained by distorted MoO4 complexes. Limited availability of anchor silanol groups at high loadings forces the MoO4 groups to form more strained configurations. The occurrence of strain is linked to the increase in reactivity.

WGS catalysis and in situ studies of CoO(1-x), PtCo(n)/Co3O4, and Pt(m)Co(m')/CoO(1-x) nanorod catalysts.

Water-gas shift (WGS) reactions on Co3O4 nanorods and Co3O4 nanorods anchoring singly dispersed Pt atoms were explored through building correlation of catalytic performance to surface chemistry of catalysts during catalysis using X-ray absorption spectroscopy, ambient pressure X-ray photoelectron spectroscopy (AP-XPS), and environmental TEM. The active phase of pure Co3O4 during WGS is nonstoichiometric cobalt monoxide with about 20% oxygen vacancies, CoO0.80. The apparent activation energy (Ea) in the temperature range of 180-240 °C is 91.0 ± 10.5 kJ mol(-1). Co3O4 nanorods anchoring Pt atoms (Pt/Co3O4) are active for WGS with a low Ea of 50.1 ± 5.0 kJ mol(-1) in the temperature range of 150-200 °C. The active surface of this catalyst is singly dispersed Pt1Co(n) nanoclusters anchored on Co3O4 (Pt1/Co3O4), evidenced by in situ studies of extended X-ray absorption fine structure spectroscopy. In the temperature range of 200-300 °C, catalytic in situ studies suggested the formation of Pt(m)Co(m') nanoclusters along with the reduction of Co3O4 substrate to CoO(1-x). The new catalyst, Pt(m)Co(m')/CoO(1-x) is active for WGS with a very low Ea of 24.8 ± 3.1 kJ mol(-1) in the temperature range of 300-350 °C. The high activity could result from a synergy of Pt(m)Co(m') nanoclusters and surface oxygen vacancies of CoO(1-x).

Scalable nano-bioprobes with sub-cellular resolution for cell detection.

Here we present a carbon nanotube based device to noninvasively and quickly detect mobile single cells with the potential to maintain a high degree of spatial resolution. The device utilizes standard complementary metal oxide semiconductor (CMOS) technologies for fabrication, allowing it to be easily scalable (down to a few nanometers). Nanotubes are deposited using electrophoresis after fabrication in order to maintain CMOS compatibility. The devices are spaced by 6 µm which is the same size or smaller than a single cell. To demonstrate its capability to detect cells, we performed impedance spectroscopy on mobile human embryonic kidney (HEK) cells, neurons cells from mice, and yeast cells (S. pombe). Measurements were performed with and without cells and with and without nanotubes. Nanotubes were found to be crucial to successfully detect the presence of cells. The devices are also able to distinguish between cells with different characteristics.

Chitosan and chitosan-ZnO-based complex nanoparticles: formation, characterization, and antibacterial activity.

Nanostructured chitosan (CS) and a chitosan-Zn based (Zn-CS) complex have been synthesized and simultaneously deposited on cotton fabrics using ultrasound. SEM measurements revealed that the coating consists of nanoparticles (NPs) of ca. 40 nm in diameter, homogeneously dispersed along the yarns. XANES studies pointed out that the complex consisted of a less than 2.1 nm ZnO core to which the chitosan was bonded. Additionally, FTIR measurements indicated the in situ formation of a Zn-CS complex which is the only deposited material on the cotton surface. The antibacterial properties of the CS and Zn-CS coated textiles were tested against Gram positive and Gram negative bacteria species. More than two-fold increase of the antibacterial activity of Zn-CS NP coated textiles was detected as compared to the fabrics treated with the sonochemically synthesized CS NPs alone. The sonochemical technique appears to be a suitable method for producing organic NPs of soluble compounds, without loss of their intrinsic properties, i.e. the antimicrobial activity of chitosan. Moreover, hybrid nanoorganometallic particles were simultaneously synthesized and deposited on cotton sonochemically.

Giant electrostriction in Gd-doped ceria.

Gd-doped CeO(2) exhibits an anomalously large electrostriction effect generating stress that can reach 500 MPa. In situ XANES measurements indicate that the stress develops in response to the rearrangement of cerium-oxygen vacancy pairs. This mechanism is fundamentally different from that of materials currently in use and suggests that Gd-doped ceria is a representative of a new family of high-performance electromechanical materials.