Mild aseptic lymphocyte-dominated vasculitis-associated lesion (ALVAL)-type reactions also present in patients with failed knee prostheses.

Aims: Metal particles detached from metal-on-metal hip prostheses (MoM-THA) have been shown to cause inflammation and destruction of tissues. To further explore this, we investigated the histopathology (aseptic lymphocyte-dominated vasculitis-associated lesions (ALVAL) score) and metal concentrations of the periprosthetic tissues obtained from patients who underwent revision knee arthroplasty. We also aimed to investigate whether accumulated metal debris was associated with ALVAL-type reactions in the synovium. Methods: Periprosthetic metal concentrations in the synovia and histopathological samples were analyzed from 230 patients from our institution from October 2016 to December 2019. An ordinal regression model was calculated to investigate the effect of the accumulated metals on the histopathological reaction of the synovia. Results: Median metal concentrations were as follows: cobalt: 0.69 µg/g (interquartile range (IQR) 0.10 to 6.10); chromium: 1.1 µg/g (IQR 0.27 to 4.10); and titanium: 1.6 µg/g (IQR 0.90 to 4.07). Moderate ALVAL scores were found in 30% (n = 39) of the revised knees. There were ten patients with an ALVAL score of 6 or more who were revised for suspected periprosthetic joint infection (PJI), aseptic loosening, or osteolysis. R2 varied between 0.269 and 0.369 for the ordinal regression models. The most important variables were model type, indication for revision, and cobalt and chromium in the ordinal regression models. Conclusion: We found that metal particles released from the knee prosthesis can accumulate in the periprosthetic tissues. Several patients revised for suspected culture-negative PJI had features of an ALVAL reaction, which is a novel finding. Therefore, ALVAL-type reactions can also be found around knee prostheses, but they are mostly mild and less common than those found around metal-on-metal prostheses.

In utero deposition of trace elements and metals in tissues.

INTRODUCTION: All animals, including humans, are exposed to heavy metals which are known to accumulate in different tissues, especially in bone. During pregnancy, the maternal bone turnover is increased and the metals in the mother's body can be mobilized into the bloodstream. Heavy metals in maternal blood are known to pass through the placenta to the fetal blood and finally, deposited to bone tissue. However, there are no studies on the concentration of metals in the fetal solid tissues and until now, the rate of metal transfer from mother to fetus is not exactly known. MATERIALS AND METHODS: Samples of the blood, liver, placenta, and three different bones were collected from 17 pregnant ewes and their 27 fetuses. The animals had no known exposure to heavy metals. The concentrations of Al, As, Ba, Ca, Cd, Co, Cr, Cu, Fe, Hg, K, Mg, Mn, Mo, Na, Ni, P, Pb, Rb, Sb, Sn, Sr, Te, Ti, Tl, V, and Zn were analyzed using ICP-MS. RESULTS AND DISCUSSION: The concentration of Sb, Sn, Te, and Tl were under the detection limit in all the samples. The other metals were found in all maternal and fetal tissues, suggesting that all detectable metals cross the placenta. Blood concentrations were low compared to solid tissue concentrations. The concentrations of essential elements varied between maternal and fetal tissues, which could be explained by biological differences. The differences in concentrations of non-essential elements between the ewe and fetuses were smaller. The most significant differences were between maternal and fetal concentrations of Ba and Sr, which is at least partly explained by the mineralization degree of the bone. CONCLUSION: Heavy metals accumulate in fetal solid tissues in sheep that are not directly exposed to heavy metals. Because of the differences in anatomy between human and sheep placenta, the accumulation in the tissue of human fetuses should be extrapolated cautiously. However, there might be some clinical relevance for fertile aged women who are exposed to heavy metals, such as women who work in the metal industry or who have undergone joint replacement surgery.

Phytoextraction and recovery of rare earth elements using willow (Salix spp.).

Soil and water contaminations are caused by rare earth elements (REEs) due to mining and industrial activities, that threaten the ecosystem and human health. Therefore, phytoremediation methods need to be developed to overcome this problem. To date, little research has been conducted concerning the phytoremediation potential of Salix for REEs. In this study, two Salix species (Salix myrsinifolia and Salix schwerinii) and two Salix cultivars (Klara and Karin) were hydroponically exposed to different concentrations of six-REE for 4 weeks. The treatments were: T1 (Control: tap water), T2 (La: 50 mg/L) and T3 (La 11.50 + Y 11 + Nd 10.50 + Dy 10 + Ce 12 and Tb 11.50 in mg L-1). The effects of the REE on Salix growth indicators (height, biomass, shoot diameter and root length), concentrations of REE in the produced biomass, and accumulation of REE in different parts of the Salix (stem, root, and leaf) tissues, were determined. In addition, the retention of REE in ashes following Salix combustion (800 and 1000 °C) was determined. The result indicates that with La and REE exposure, the height growth, dry biomass, shoot diameter and root length of all Salix remained equivalent to the control treatment excluding Klara, which displayed relatively higher growth in all parameters. Further, among the REE studied, the highest La concentration (8404 µg g-1 DW) and La accumulation (10,548 µg plant-1) were observed in Karin and Klara root respectively. Translocations and bioconcentration factors were discovered at <1 for all Salix, which indicates their phytostabilization potential. The total REE concentrations in bottom ashes varied between 7 and 8% with retention rates between 85 and 89%. This study demonstrates that Salix are suitable candidates for REE phytostabilization and the remediation of wastewater sites to limit metals percolating to the water layers in the ecosystem.

Exposure to leachates from post-consumer plastic and recycled rubber causes stress responses and mortality in a copepod Limnocalanus macrurus.

Effects of household post-consumer plastics and tyre rubber on a Baltic Sea copepod Limnocalanus macrurus were assessed. Fragments of commercial recycled low-density polyethylene vegetable bags and rubber originating from recycled car tyres were incubated in seawater, and the copepods were exposed to the filtrate of the water. L. macrurus experienced erratic swimming behaviour and increased mortality in the filtrate of unwashed vegetable bags, containing elevated concentrations of alcohols, organic acids and copper. Responses of the antioxidant defence system (ADS) were recorded in copepods exposed to rubber treatments containing high concentrations of zinc. Significant responses in the ADS enzymes indicate that reactive oxygen species (ROS) formation was exceeding the detoxification capacity of the ADS which may further lead to prolonged state of oxidative stress. Observed effects of exposure on the biochemical level coincide with impaired swimming activity of the copepods, indicating possible irreversible cellular responses leading to behavioural changes and mortality.

Phenotypic Plasticity of Common Wasps in an Industrially Polluted Environment in Southwestern Finland.

Insects vary in the degree of their adaptability to environmental contamination. Determining the responses with phenotypic plasticity in ecologically important species in polluted environments will ease further conservation and control actions. Here, we investigated morphological characteristics such as body size, body mass, and color of the common wasp Vespula vulgaris in an industrially polluted environment, considering different levels of metal pollution, and we studied the localization of contaminants in the guts of wasps. We revealed some differences in morphological characteristics and melanization of wasps collected in habitats with high, moderate, and low levels of pollution. The results indicated that V. vulgaris from highly polluted environments had reduced melanin pigmentation on the face but increased melanin pigmentation on the 2nd tergite of the abdomen. In addition, with transmission electron microscopy (TEM) and energy dispersive X-ray analysis (EDX), we found metal particles from the midgut of wasps originating from the polluted environment. Most of the particles were encapsulated with melanin pigment. This finding confirmed that in wasps, ingested metal particles are accumulated in guts and covered by melanin layers. Our data suggest that wasps can tolerate metal contamination but respond phenotypically with modification of their size, coloration, and probably with the directions of the melanin investments (immunity or coloration). Thus, in industrially polluted areas, wasps might probably survive by engaging phenotypic plasticity with no significant or visible impact on the population.

Phosphorus Recovery from Sewage Sludge Using Acidithiobacilli.

Sewage sludge contains a significant amount of phosphorus (P), which could be recycled to address the global demand for this non-renewable, important plant nutrient. The P in sludge can be solubilized and recovered so that it can be recycled when needed. This study investigated the P solubilization from sewage sludge using Acidithiobacillus thiooxidans and Acidithiobacillus ferrooxidans. The experiment was conducted by mixing 10 mL of sewage sludge with 90 mL of different water/liquid medium/inoculum and incubated at 30 °C. The experiment was conducted in three semi-continuous phases by replacing 10% of the mixed incubated medium with fresh sewage sludge. In addition, 10 g/L elemental sulfur (S) was supplemented into the medium in the third phase. The pH of the A. thiooxidans and A. ferrooxidans treated sludge solutions was between 2.2 and 6.3 until day 42. In phase 3, after supplementing with S, the pH of A. thiooxidans treated sludge was reduced to 0.9, which solubilized and extracted 92% of P. We found that acidithiobacilli supplemented with S can be used to treat sludge, i.e., achieve hygienization, removal of heavy metals, and solubilization and recovery of P.

Exploring the Biochemical Foundations of a Successful GLUT1-Targeting Strategy to BNCT: Chemical Synthesis and In Vitro Evaluation of the Entire Positional Isomer Library of ortho-Carboranylmethyl-Bearing Glucoconjugates.

Boron neutron capture therapy (BNCT) is a noninvasive binary therapeutic modality applicable to the treatment of cancers. While BNCT offers a tumor-targeting selectivity that is difficult to match by other means, the last obstacles preventing the full harness of this potential come in the form of the suboptimal boron delivery strategies presently used in the clinics. To address these challenges, we have developed delivery agents that target the glucose transporter GLUT1. Here, we present the chemical synthesis of a number of ortho-carboranylmethyl-substituted glucoconjugates and the biological assessment of all positional isomers. Altogether, the study provides protocols for the synthesis and structural characterization of such glucoconjugates and insights into their essential properties, for example, cytotoxicity, GLUT1-affinity, metabolism, and boron delivery capacity. In addition to solidifying the biochemical foundations of a successful GLUT1-targeting approach to BNCT, we identify the most promising modification sites in d-glucose, which are critical in order to further develop this strategy toward clinical use.

Bio-based wood preservatives: Their efficiency, leaching and ecotoxicity compared to a commercial wood preservative.

Companies in the wood industry are constantly developing their outdoor products. The possibility of using bio-based chemicals as an alternative to traditional wood preservatives-regulated in Europe by The Biocidal Products Regulation No 528/2012-has been considered, but chemical leaching from the wood decreases its effectiveness and may negatively affect the environment. This study aims to compare the effectiveness of bio-based chemicals with potential use in wood preservation to commercially available preservatives, to investigate their fixation to wood and their ecotoxicity and to quantify the potentially toxic elements leached from the wood. Pyrolysis distillates of tree bark, organic acids found in distillates, Colatan GT10 tannin extract and log soaking liquid as a hardwood veneer process residue were tested and compared with commercial pine oil and a copper-based wood preservative. In the wood decay test of impregnated pine sapwood specimens, Colatan GT10 extract performed as well as the commercial wood preservatives. The same decay trial with leached specimens significantly reduced the performance of the bio-based chemicals. The results of the ecotoxicity test with photoluminescent Aliivibrio fischeri bacteria showed that many bio-based chemicals with potential use in wood preservation have markedly lower ecotoxicity than commercially available wood preservatives, but the ecotoxicity of some bio-based chemicals is higher, as in the case of some of the pyrolysis distillates. The wood preservation efficiency and the ecotoxicity of the studied chemicals had a poor correlation, implying that other factors besides treatment agent toxicity play a role in deterring fungal growth on treated wood. The amount of elemental toxins in the leachates was low. These results emphasize the importance of the chemical ecotoxicity of bio-based preservative compounds, as their detrimental effect on the environment can be higher than that of the traditional preservatives unless effectively linked to wood to prevent leaching.

Retention of metals in periprosthetic tissues of patients with metal-on-metal total hip arthroplasty is reflected in the synovial fluid to blood cobalt transfer ratio in the presence of a pseudotumour.

BACKGROUND: Modern metal-on-metal (MOM) arthroplasties were performed for over a decade before alarming reports of adverse metal reactions dramatically reduced their use. Failures are seen more often with high-wearing implants, but also well-positioned components with more favourable wear patterns can cause problems. There are no specific clinical indicators that could help us to predict the prognosis of these implants. For this reason, we still need more information on the effect of underlying factors that contribute to this process. METHODS: In this prospective cohort study, we investigated how cup orientation and type of pseudotumour determined by the Hart classification effect the distribution of metals in blood, synovial fluid and tissues surrounding the metal-on-metal hip prosthesis in revision surgery patients. One thousand two hundred twenty-nine metal-on-metal hip patients were screened and of those, 60 patients that had a revision surgery due to adverse metal reaction were included. Whole blood, synovial fluid and synovial/pseudotumour tissue samples were analysed for metal ion concentrations (Co, Cr, Mo and Ti). RESULTS: The lowest metal concentrations were found when both cup anteversion and inclination were optimal, and the highest when both were suboptimal. Suboptimal anteversion alone raised Cr-ion concentrations more than suboptimal inclination. The concentrations of metals in blood, synovial fluid or synovial soft tissue were the same in patients with and without a pseudotumour, but the relative transfer percentage of cobalt from synovial fluid to blood was higher in patients with a pseudotumour. CONCLUSIONS: The implant orientation alone does not explain the metal concentrations found in tissues or distribution of metals between different tissues. The accumulation of metals in periprosthetic soft tissues increase the total metal load, and in the presence of a pseudotumour this is reflected in the transfer ratio of Co from synovial fluid to the blood. The total metal load of the pseudotumour tissue should be defined in future studies to determine if this will provide new insights for clinical practice.

Detoxification of wood-combustion ashes containing Cr and Cd by thermal treatment.

This study assesses the potential of thermal processing for detoxification of wood-combustion ashes that contain high levels of Cr and Cd. Thermal treatment (1000 °C) of bottom ash and fly ash in an oxidising gas (air) atmosphere resulted in: low volatilisation of Cd and most other heavy metals, oxidation of Cr in the ashes to Cr (VI), and, in the case of the fly ash, significantly increased leaching of Cr and Mo. Thermal treatment in a nitrogen atmosphere resulted in local reducing conditions due to oxidation of ash-derived carbon to CO (g). Thermal treatments in this atmosphere and in a reducing atmosphere consisting of 10 % H2 and the balance N2 detoxified the ashes in at least two ways: (i) by substantially removing Cd, Pb, Bi, Tl, and, in the case of the fly ash, Zn from the ashes by volatilisation; and (ii) by thermal reduction of Cr (VI) in the ashes. There was at least a 100-fold reduction in the leaching of total Cr from both the bottom ash and the fly ash following the thermal treatments in reducing conditions. Chromium only leached from the detoxified bottom ash to a significant extent in acidic conditions (pH < 4).

Addressing the Biochemical Foundations of a Glucose-Based "Trojan Horse"-Strategy to Boron Neutron Capture Therapy: From Chemical Synthesis to In Vitro Assessment.

Boron neutron capture therapy (BNCT) for cancer is on the rise worldwide due to recent developments of in-hospital neutron accelerators which are expected to revolutionize patient treatments. There is an urgent need for improved boron delivery agents, and herein we have focused on studying the biochemical foundations upon which a successful GLUT1-targeting strategy to BNCT could be based. By combining synthesis and molecular modeling with affinity and cytotoxicity studies, we unravel the mechanisms behind the considerable potential of appropriately designed glucoconjugates as boron delivery agents for BNCT. In addition to addressing the biochemical premises of the approach in detail, we report on a hit glucoconjugate which displays good cytocompatibility, aqueous solubility, high transporter affinity, and, crucially, an exceptional boron delivery capacity in the in vitro assessment thereby pointing toward the significant potential embedded in this approach.

Thermal treatment of municipal solid waste incineration fly ash: Impact of gas atmosphere on the volatility of major, minor, and trace elements.

Development of thermal processes for selective recovery of Zn and other valuable elements from municipal solid waste incineration (MSWI) fly ash requires comprehensive knowledge of the impact of gas atmosphere on the volatile behaviour of the element constituents of the ash at different reaction temperatures. This study assesses the partitioning of 18 elements (Al, As, Bi, C, Ca, Cd, Cl, Cu, K, Mg, Na, P, Pb, S, Sb, Sn, Ti, and Zn) between condensed and gaseous phases during thermal treatment of MSWI fly ash in both oxidising gas and reducing gas atmospheres, at different temperatures spanning the range 200-1050 °C. The operating atmosphere had major impacts on the partitioning of the following elements: As, Bi, C, Cd, Cu, Na, Pb, S, Sb, Sn, and Zn. The partitioning of these elements cannot be accurately predicted over the full range of investigated operating conditions with global thermodynamic equilibrium calculations alone, i.e. without also considering chemical kinetics and mass transfer. In oxidising conditions, the following elements were predominately retained in condensed phases, even at high temperatures: As, Bi, Sb, Sn, and Zn. All these elements, except As, were largely released to the gas phase (>70%) at high temperatures in reducing conditions. The impact of gas atmosphere on the volatility of Cd and Pb was greatest at low reaction temperatures (below ~750 °C). Results for volatile matrix elements, specifically C, Cl, K, Na, and S, are interpreted in terms of the mechanisms governing the release of these elements to the gas phase.

Facing the threat: common yellowjacket wasps as indicators of heavy metal pollution.

We investigated the common wasp, Vespula vulgaris as a bioindicator and biomonitor of metals in the industrial area. Using traps, we collected 257 yellowjackets along a pollution gradient in the Harjavalta Cu-Ni smelter in Southwest Finland. Our method detected metal elements such as arsenic (As), cobalt (Co), copper (Cu), iron (Fe), nickel (Ni), lead (Pb), zinc (Zn), and mercury (Hg) in wasps. The data analyses revealed V. vulgaris can be a proper indicator for As, Cd, Co, Cu, Ni, and Pb, rather than for Fe and Zn contamination. Body burdens of As, Cd, Co, Cu, Ni, and Pb decreased with an increase in distance from smelter. Enrichment factor (EF) followed the pattern Pb ˃ Cd ˃ As ˃ Co ˃ Cu ˃ Ni. The highest bioaccumulation (BAF) values were revealed for Cd (5.9) and the lowest for Pb (0.1). Specially designed software (WaspFacer) allowed revealing body burdens of As, Cd, Co, Cu, Ni, and Pb to be associated with rather smaller than more asymmetric facial colour markings in yellowjackets. These results add to the body of literature on how heavy metal contaminants can have tangible phenotypic effects on insects and open future opportunities for using wasps as indicators of metal pollution.

The effect of the shoeless course on particle concentrations and dust composition in schools.

Airborne particles may effect on indoor air quality in schools. One significant particle source is outdoor dust and soil transported indoors on people's shoes, which may be resuspended, and further inhaled by pupils and teachers. In many Finnish schools, shoes are taken off by coat racks near the classrooms (shoe schools). The new course of action is to take shoes off right when entering the building (sock schools). In this study, particle mass and number concentrations, together with chemical composition of the dust were investigated in sock and shoe schools. According to results, PM10 and PM15 concentrations in corridors were significantly higher in shoe schools compared to sock schools (p < 0.05). The shoeless course did not affect on the particle number concentrations, but the increases in the number concentrations originated from diners. The elemental concentrations (Li, Al, Si, Cr, Mn, Fe, Co, Ni, Cu, Zn, Cd, Ba, Pb) in settled dust were also higher in shoe schools compared to sock schools, and the Zn concentrations differed significantly (p < 0.05). In conclusion, this study showed that by taking the shoes off when entering the school building you can enhance the indoor air quality by reducing the particle mass concentrations.

Synthesis of clay-cellulose biocomposite for the removal of toxic metal ions from aqueous medium.

Clay-cellulose biocomposite (CCB) was synthesized in the present study. Spin and pressure-induced heating was applied to aggregate exfoliated clay tubules and cellulose using polyethylene glycol as an intermediate. The synthesized CCB was modified in the presence of NaOH at high temperature to obtain negative surface charge on the adsorbent. Physico-chemical properties of CCB were evaluated using different characterization techniques including Fourier transform infrared (FT-IR) and X-ray photoelectron (XPS) spectroscopy. The efficiency of the synthesized biocomposite for Pb(II) and Cd(II) removal from water was studied via laboratory scale experiments. The adsorption kinetics of Pb(II) and Cd(II) onto CCB was well described by the pseudo-second-order kinetic model. The maximum Langmuir adsorption capacity of CCB was found to be 389.78 and 115.96 mg g-1 for Pb(II) and Cd(II), respectively. Fixed-bed column studies were conducted for the adsorption system to compare the adsorption performance of CCB in continuous mode.

Volatilisation of major, minor, and trace elements during thermal processing of fly ashes from waste- and wood-fired power plants in oxidising and reducing gas atmospheres.

This study assesses the volatility of 15 elements (As, Bi, C, Cd, Cl, Cu, K, Mn, Na, P, Pb, S, Sb, Sn, and Zn) during thermal processing of fly ashes obtained from four waste-to-energy plants and one wood-combustion plant. Differences in volatility in oxidising and reducing atmospheres (air and 10% H2/90% N2) were assessed at two temperatures, 700 and 1000 °C. P and Mn were predominately retained in all ashes regardless of the operating atmosphere and temperature. Other elements showed significant variation in volatility depending on the type of fly ash, atmosphere, and temperature. Heat-treatment of the wood-combustion fly ash in the air atmosphere resulted in low release of K, Na, and all investigated heavy metals and metalloids. Several valuable elements, including Zn, Sb, Sn, and Bi, were significantly more volatile in the reducing atmosphere than in the oxidising atmosphere, particularly at 1000 °C. Other elements were either less volatile, equally volatile, or only marginally more volatile when the ashes were heated at 1000 °C in the reducing atmosphere. These elements include C, Cl, Cu, and, in the case of fly ashes derived from municipal solid waste, Cd and Pb. A two-step process, in which municipal solid waste incineration fly ash is first heated in an oxidising atmosphere and then in a reducing atmosphere, is proposed for production of a chloride-free zinc concentrate. Evaluation of the two-step process at 880 °C shows good potential for selective volatilisation of Zn with other valuable elements, including Sn, Sb, and Bi.

Enhanced interlayer trapping of Pb(II) ions within kaolinite layers: intercalation, characterization, and sorption studies.

Lead (Pb(II)) pollution in water poses a serious threat to human health in many parts of the world. In the past decades, research has been aimed at developing efficient and cost-effective methods to address the problem. In this study, dimethyl sulfoxide (DMSO) and potassium acetate (K-Ac) intercalated kaolinite complexes were synthesized and subsequently utilized for Pb(II) removal from water. The intercalation of kaolinite with DMSO was found to be useful for expanding the interlayer space of the clay mineral from 0.72 to 1.12 nm. Kaolinite intercalation with K-Ac (KDK) increased the interlayer space from 1.12 to 1.43 nm. The surface area of KDK was found to be more than threefold higher as compared to natural kaolinite (NK). Batch experimental results revealed that the maximum Pb(II) uptake capacity of KDK was 46.45 mg g-1 which was higher than the capacity of NK (15.52 mg g-1). Reusability studies showed that KDK could be reused for 5 cycles without substantially losing its adsorption capacity. Furthermore, fixed-bed column tests confirmed the suitability of KDK in continuous mode for Pb(II) removal. Successful application of intercalated kaolinite for Pb(II) adsorption in batch and column modes suggests its application in water treatment (especially removal of divalent metals).

Transcriptional effects of cadmium on iron homeostasis differ in calamine accessions of Noccaea caerulescens.

Calamine accessions of the zinc/cadmium/nickel hyperaccumulator, Noccaea caerulescens, exhibit striking variation in foliar cadmium accumulation in nature. The Ganges accession (GA) from Southern France displays foliar cadmium hyperaccumulation (>1000 µg g-1 DW), whereas the accession La Calamine (LC) from Belgium, with similar local soil metal composition, does not (<100 µg g-1 DW). All calamine accessions are cadmium hypertolerant. To find out the differences between LC and GA in their basic adaptation mechanisms, we bypassed the cadmium excluding phenotype of LC by exposing the plants to 50 µm cadmium in hydroponics, achieving equal cadmium accumulation in the shoots. The iron content increased in the roots of both accessions. GA exhibited significant decreases in manganese and zinc contents in the roots and shoots, approaching those in LC. Altogether 702 genes responded differently to cadmium exposure between the accessions, 157 and 545 in the roots and shoots, respectively. Cadmium-exposed LC showed a stress response and had decreased levels of a wide range of photosynthesis-related transcripts. GA showed less changes, mainly exhibiting an iron deficiency-like response. This included increased expression of genes encoding five iron deficiency-regulated bHLH transcription factors, ferric reduction oxidase FRO2, iron transporters IRT1 and OPT3, and nicotianamine synthase NAS1, and decreased expression of genes encoding ferritins and NEET (a NEET family iron-sulfur protein), which is possibly involved in iron transfer, distribution and/or management. The function of the IRT1 gene in the accessions was compared. We conclude that the major difference between the two accessions is in the way they cope with iron under cadmium exposure.

Synthesis of S-ligand tethered cellulose nanofibers for efficient removal of Pb(II) and Cd(II) ions from synthetic and industrial wastewater.

Cellulose nanofibers (CNFs) tethered with sulphur as anionic ligand were synthesized from medical absorbent cotton by dissolution with NaOH, CO(NH2)2 followed by mechanical intrusion of sulphur from SC(NH2)2 at an elevated temperature. The solid-phase CNFs embedded with sulphur complexes possessed negative sites which were used to remove cationic metals viz., Pb(II) and Cd(II) from synthetic and industrial wastewater. The physicochemical properties of the CNFs were analyzed by Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM), pH at point of zero charge (pHpzc) and X-ray photoelectron spectroscopy (XPS). Batch adsorption studies were conducted with synthetic wastewater to optimize the conditions for Pb(II) and Cd(II) removal by CNFs. Different adsorption kinetic models were applied to assess and define the adsorption mechanism. The maximum Langmuir adsorption capacity was found to be 1.16 and 0.82 mmol g-1 for Pb(II) and Cd(II) ions, respectively. Regeneration studies showed that the CNFs can be reused using 0.1 M NaOH as eluent. The percentage removal efficiency of different cationic metals by CNFs from untreated industrial wastewater ranged from ca. 90-98%.

Scalable Synthesis of Biodegradable Black Mesoporous Silicon Nanoparticles for Highly Efficient Photothermal Therapy.

Porous silicon (PSi) has attracted wide interest as a potential material for various fields of nanomedicine. However, until now, the application of PSi in photothermal therapy has not been successful due to its low photothermal conversion efficiency. In the present study, biodegradable black PSi (BPSi) nanoparticles were designed and prepared via a high-yield and simple reaction. The PSi nanoparticles possessed a low band gap of 1.34 eV, a high extinction coefficient of 13.2 L/g/cm at 808 nm, a high photothermal conversion efficiency of 33.6%, good photostability, and a large surface area. The nanoparticles had not only excellent photothermal properties surpassing most of the present inorganic photothermal conversion agents (PCAs) but they also displayed good biodegradability, a common problem encountered with the inorganic PCAs. The functionality of the BPSi nanoparticles in photothermal therapy was verified in tumor-bearing mice in vivo. These results showed clearly that the photothermal treatment was highly efficient to inhibit tumor growth. The designed PCA material of BPSi is robust, easy to prepare, biocompatible, and therapeutically extremely efficient and it can be integrated with several other functionalities on the basis of simple silicon chemistry.