Structure and kinetics of fatty acid Langmuir monolayers on zinc salt solutions.

The adsorption of zinc cations under behenic acid Langmuir monolayers was investigated by means of isotherm measurements, grazing incidence X-ray diffraction and Brewster angle microscopy. The structure of the films was characterized as a function of Zn(2+) concentration, for three different counterions (chloride, iodide, bromide) and at two subphase pHs (5.5 and 7.5). At pH 5.5 and in the studied concentration range, Zn(2+) adsorption leads to a condensation of the fatty acid monolayer with the same phase transitions as over pure water. In contrast, at higher pH the organic X-phase is evidenced immediately above a concentration threshold without any ion organization. Even though Cu(2+) and Zn(2+)cations induce both the fatty acid X-phase, the kinetics of its formation appears strongly different. Indeed, as for Mg(2+) and Cd(2+), the intermediate new I-structure is evidenced in the course of Zn(2+) adsorption although superstructures are observed only for Mg(2+) and Cd(2+). However, for Zn(2+), the I-phase evolves to the final state through a new structure called X' and a continuous X'-X transition. Finally, any effect of the counterion is evidenced neither during the kinetic process nor in the final state.

Limited propagation of lattice distortion in trilayer Langmuir-Blodgett films: correlation with mesoscopic structure.

The structure of trilayer Langmuir-Blodgett (LB) films on oxidized silicon wafers has been investigated using grazing incidence X-ray diffraction at various incidence angles and atomic force microscopy (AFM). These films are formed by two behenic acid (BA) layers and a third monolayer of amphiphilic molecules having different architectures. These molecules have the same polar head and differ from each other by the chain, either saturated or unsaturated hydrogenated or semi-fluorinated. The structure of the first BA monolayer appears as unchanged in all cases, whereas a condensation of the second BA monolayer is evidenced when the third layer is not formed with the saturated hydrogenated chain. We interpret this condensation as resulting from the mismatch between the lattices of the second BA layer and the external monolayer, possibly associated with the formation of a new monolayer-air interface creating line tension effects. Line tension estimation has also been made from the size of the holes observed in the different LB films.

Contribution toward comprehension of contact angle values on single polydimethylsiloxane and poly(ethylene oxide) polymer networks.

The large application ranges of polydimethylsiloxane (PDMS) and poly(ethylene oxide) (PEO) based materials justify the importance of controlling polymer surface properties including morphology and wettability behavior. However, it appears that the reported contact angle values of PDMS surfaces show significant scattering which cannot always be interpreted in terms of sole chemical data. In addition, few values are reported concerning pure PEO surfaces, since the polymer generally swells in the presence of water. Thus, in order to correlate surface properties with sample preparation, several single PDMS and PEO polymer networks were synthesized with varying cross-linkers and different cross-linking densities. First, the sample surface topography was systematically analyzed by atomic force microscopy (AFM). It was proven that the removal process of the polymer film from the mold plays a significant role in surface topography according to the vitreous or rubbery state of the given polymer network at room temperature irrespective of mold surface treatment. AFM-scale smooth surfaces can be obtained for all the samples by removing them systematically from the mold at a temperature below the α-relaxation temperature. Dynamic water contact angles were then measured and the values analyzed as a function of cross-linker nature and cross-linking density.

Evolution toward the X phase of fatty acid Langmuir monolayers on a divalent cation solution.

The structure of docosanoic acid monolayers spread over chloride salt solutions of copper was investigated by means of isotherm measurements, grazing incidence X-ray diffraction, and Brewster angle microscopy, as a function of the ion concentration and at two subphase pHs (5.5 and 7.5). The X phase is evidenced immediately above a concentration threshold which depends on the pH. The sequence of phases leading to this rigid phase involves two different processes depending on the pH. The initial L(2h) phase evolves toward an X-like phase through a phase transition which is first order at pH 7.5 while it is second order at pH 5.5. The transition is then followed by a continuous evolution toward the X phase.

Sliding behavior of liquid droplets on tilted Langmuir-Blodgett surfaces.

The sliding behavior of liquid droplets on inclined Langmuir-Blodgett surfaces was investigated. The critical sliding angle defined as the tilt angle of the surface at which the drop slides down as well as the advancing and receding contact angles was measured for five different liquids on five surfaces. In addition, the contact line geometry was analyzed at critical sliding angle. The experimental relationship between the surface tension forces resulting from contact angle hysteresis and the weight of the drop was compared to theoretical predictions. Even though the shape of the drop bases was found as skewed ellipses, a model assuming parallel-sided elongated drops is shown to describe reasonably the experimental values. This result probably indicates the main influence of the capillary forces at the rear and front edges of the drop with respect to that exerted on the lateral sides.

Molecular recognition controls the organization of mixed self-organized bis-urea-based mineralization templates for CaCO(3).

To investigate the role and importance of nondirectional electrostatic interactions in mineralization, we explored the use of Langmuir monolayers in which the charge density can be tuned using supramolecular interactions. It is demonstrated that, in mixed Langmuir monolayers of bis-ureido surfactants containing oligo(ethylene oxide) and ammonium head groups associated with matching or nonmatching spacers between the two urea groups, the organization is controlled by molecular recognition. These different organizations of the molecules lead to different nucleation behavior in the mineralization of calcium carbonate. The formation of modified calcite and vaterite crystals was induced selectively by different phases of mixed monolayers, and they were characterized by SEM, TEM, and SAED. To understand the influence of the mixed Langmuir monolayers on the crystallization process, we studied the mixtures by means of (pi-A) isotherms and Brewster angle microscopy observations. Infrared reflection-absorption spectroscopy experiments were also performed on Langmuir-Schaefer films. From these results, we conclude that the local organization of the two systems discussed here gives rise to differences in both charge density and flexibility that together determine not only polymorph selection and the nucleation face but also the morphology of the resulting crystals.

Spontaneous polymerization at the air-water interface: a Brewster angle microscopy study.

When a dioctadecyldimethylammonium bromide (DODA) monolayer is spread onto a styrene sulfonate (SSt) aqueous solution, this monomer undergoes a spontaneous polymerization process [Fichet, O; Teyssié, D. Macromolecules 2002, 35, 5352]. However, the polymer synthesized in this monolayer cannot be investigated by classical characterization techniques. Brewster angle microscopy has thus been used as a complementary method in order to study this spontaneous polymerization. From these measurements, the threshold concentration above which the spontaneous polymerization occurs has been determined more precisely; the monomer adsorption under the DODA monolayer has been evidenced as being very fast, as supposed previously; moreover, sodium bicarbonate is confirmed as an inhibitor of the polymerization. Also, the replacement of SSt by toluene sulfonate (TSt) confirms the SSt spontaneous polymerization. Finally, the molecular weight and/or the structure of the polymer synthesized in the monolayer seems to be different from those synthesized in solution.