Atmospheric Pressure Plasma Deposition of Hydrophilic/Phobic Patterns and Thin Film Laminates on Any Surface.

Patterned and layered hydrophilic/phobic coatings were deposited on multiple surfaces using nonfluorinated precursors (AA, acrylic acid; PMA, propargyl methacrylate) with an atmospheric pressure dielectric barrier discharge operating in open air. Water contact angles of the resulting films could be tuned from <5° (superhydrophilic) to >135° (very hydrophobic) by adjusting the AA/PMA feed ratio and/or via postdeposition exposure of films to an Ar/O2 plasma treatment. Coatings could be applied to any surface and were seen to be water stable, due in large part to cross-linking induced from the reactivity of the PMA pendant groups. Hybrid hydrophilic/phobic patterns at submillimeter length scales, and philic/phobic/philic laminates were produced using a shadow mask and sequential deposition, respectively. Chemical heterogeneity of films was assessed using XPS, SIMS, and micro-IR imaging and suggest that localization of COOH and OH groups are primarily responsible for hydrophilicity. Overall, this work demonstrates that atmospheric pressure plasma polymerization is a simple and scalable method for robust and tunable control of wettability of surfaces of all kinds.

Molecular depth profiling of organic photovoltaic heterojunction layers by ToF-SIMS: comparative evaluation of three sputtering beams.

With the recent developments in secondary ion mass spectrometry (SIMS), it is now possible to obtain molecular depth profiles and 3D molecular images of organic thin films, i.e. SIMS depth profiles where the molecular information of the mass spectrum is retained through the sputtering of the sample. Several approaches have been proposed for "damageless" profiling, including the sputtering with SF5(+) and C60(+) clusters, low energy Cs(+) ions and, more recently, large noble gas clusters (Ar500-5000(+)). In this article, we evaluate the merits of these different approaches for the in depth analysis of organic photovoltaic heterojunctions involving poly(3-hexylthiophene) (P3HT) as the electron donor and [6,6]-phenyl C61 butyric acid methyl ester (PCBM) as the acceptor. It is demonstrated that the use of 30 keV C60(3+) and 500 eV Cs(+) (500 eV per atom) leads to strong artifacts for layers in which the fullerene derivative PCBM is involved, related to crosslinking and topography development. In comparison, the profiles obtained using 10 keV Ar1700(+) (∼6 eV per atom) do not indicate any sign of artifacts and reveal fine compositional details in the blends. However, increasing the energy of the Ar cluster beam beyond that value leads to irreversible damage and failure of the molecular depth profiling. The profile qualities, apparent interface widths and sputtering yields are analyzed in detail. On the grounds of these experiments and recent molecular dynamics simulations, the discussion addresses the issues of damage and crater formation induced by the sputtering and the analysis ions in such radiation-sensitive materials, and their effects on the profile quality and the depth resolution. Solutions are proposed to optimize the depth resolution using either large Ar clusters or low energy cesium projectiles for sputtering and/or analysis.

Adsorption of a PEO-PPO-PEO triblock copolymer on metal oxide surfaces with a view to reducing protein adsorption and further biofouling.

Abstract Biomolecule adsorption is the first stage of biofouling. The aim of this work was to reduce the adsorption of proteins on stainless steel (SS) and titanium surfaces by modifying them with a poly(ethylene oxide) (PEO)-poly(propylene oxide) (PPO)-PEO triblock copolymer. Anchoring of the central PPO block of the copolymer is known to be favoured by hydrophobic interaction with the substratum. Therefore, the surfaces of metal oxides were first modified by self-assembly of octadecylphosphonic acid. PEO-PPO-PEO preadsorbed on the hydrophobized surfaces of titanium or SS was shown to prevent the adsorption of bovine serum albumin (BSA), fibrinogen and cytochrome C, as monitored by quartz crystal microbalance (QCM). Moreover, X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry were used to characterize the surfaces of the SS and titanium after competitive adsorption of PEO-PPO-PEO and BSA. The results show that the adsorption of BSA is well prevented on hydrophobized surfaces, in contrast to the surfaces of native metal oxides.

Double protein functionalized poly-ε-caprolactone surfaces: in depth ToF-SIMS and XPS characterization.

In biomaterial research, great attention has focussed on the immobilization of biomolecules with the aim to increase cell-adhesive properties of materials. Many different strategies can be applied. In previously published work, our group focussed on the treatment of poly-ε-caprolactone (PCL) films by an Ar-plasma, followed by the grafting of 2-aminoethyl methacrylate (AEMA) under UV-irradiation. The functional groups introduced, enabled the subsequent covalent immobilisation of gelatin. The obtained coating was finally applied for the physisorption of fibronectin. The successful PCL surface functionalization was preliminary confirmed using XPS, wettability studies, AFM and SEM. In the present article, we report on an in-depth characterization of the materials developed using ToF-SIMS and XPS analysis. The homogeneous AEMA grafting and the subsequent protein coating steps could be confirmed by both XPS and ToF-SIMS. Using ToF-SIMS, it was possible to demonstrate the presence of polymethacrylates on the surface. From peak deconvoluted XPS results (C- and N-peak), the presence of proteins could be confirmed. Using ToF-SIMS, different positive ions, correlating to specific amino-acids could be identified. Importantly, the gelatin and the fibronectin coatings could be qualitatively distinguished. Interestingly for biomedical applications, ethylene oxide sterilization did not affect the surface chemical composition. This research clearly demonstrates the complementarities of XPS and ToF-SIMS in biomedical surface modification research.

Antifouling properties of poly(methyl methacrylate) films grafted with poly(ethylene glycol) monoacrylate immersed in seawater.

Biofouling of all structures immersed in seawater constitutes an important problem, and many strategies are currently being developed to tackle it. In this context, our previous work shows that poly(ethylene glycol) monoacrylate (PEGA) macromonomer grafted on preoxidized poly(methyl methacrylate) (PMMAox) films exhibits an excellent repellency against the bovine serum albumin used as a model protein. This study aims to evaluate the following: (1) the prevention of a marine extract material adsorption by the modified surfaces and (2) the antifouling property of the PEGA-g-PMMAox substrates when immersed in natural seawater during two seasons (season 1: end of April-beginning of May 2007, and season 2: end of October-beginning of November 2007). The antifouling performances of the PEGA-g-PMMAox films are investigated for different PEG chain lengths and macromonomer concentrations into the PEGA-based coatings. These two parameters are followed as a function of the immersion time, which evolves up to 14 days. The influence of the PEGA layer on marine compounds (proteins and phospholipids) adsorption is evidenced by time-of-flight secondary ion mass spectrometry (ToF-SIMS) and X-ray photoelectron spectroscopy (XPS). It was found that the antifouling efficiency of the PEGA-grafted surfaces increases with both PEGA concentration and PEG chain length.

Metal-assisted secondary ion mass spectrometry using atomic (Ga+, In+) and fullerene projectiles.

The advantages and drawbacks of using either monatomic or buckminsterfullerene primary ions for metal-assisted secondary ion mass spectrometry (MetA-SIMS) are investigated using a series of organic samples including additive molecules, polyolefins, and small peptides. Gold deposition is mostly performed by sputter-coating, and in some cases, the results are compared to those of thermal evaporation (already used in a previous article: Delcorte, A.; Médard, N.; Bertrand, P. Anal. Chem. 2002, 74, 4955). The microstructure of the gold-covered sample surfaces is assessed by scanning and transmission electron microscopies. The merits of the different sets of experimental conditions are established via the analysis of fragment and parent-like ion yields. For most of the analyzed samples, the highest yields of fragment and parent-like ions are already reached with the sole use of C60+ projectiles. Metallization of the sample does not lead to a significant additional enhancement. For polyethylene and polypropylene, however, gold metallization associated with Ga+/In+ projectiles appears to be the only way to observe large cationized, sample-specific chain segments (m/z approximately 1000-2000). A detailed study of the polypropylene mass spectra as a function of gold coverage shows that the dynamics of yield enhancement by metal nanoparticles is strongly dependent on the choice of the projectile, e.g., a pronounced increase with Ga+ and a slow decay with C60+. The cases of Irganox 1010, a polymer antioxidant, and leucine enkephalin, a small peptide, allow us to investigate the specific influence of the experimental conditions on the emission of parent(like) ions such as M+, (M + Na)+, and (M + Au)+. The results show a dependence on both the type of sample and the considered secondary ion. Using theoretical and experimental arguments, the discussion identifies some of the mechanisms underlying the general trends observed in the results. Guidelines concerning the choice of the experimental conditions for MetA-SIMS are provided.

Surface characterization of three marine bacterial strains by Fourier transform IR, X-ray photoelectron spectroscopy, and time-of-flight secondary-ion mass spectrometry, correlation with adhesion on stainless steel surfaces.

Adhesion of bacterial strains on solid substrates is likely related to the properties of the outer shell of the micro-organisms. Aiming at a better understanding and control of the biofilm formation in seawater, the surface chemical composition of three marine bacterial strains was investigated by combining Fourier transform IR spectroscopy, X-ray photoelectron spectroscopy (XPS), and time-of-flight secondary-ion mass spectrometry (ToF-SIMS). The D41 strain surface showed evidence of proteins, as deduced from the NH2 and NCO XPS and ToF-SIMS fingerprints; this strain was found to adhere to stainless steel, glass, or Teflon surfaces in a much higher quantity (2 orders of magnitude) than the two other ones, DA and D01. The latter are either enriched in COOH or sulfates, and this makes them more hydrophilic and less adherent to all substrates. Correlations with physicochemical properties and adhesion seem to demonstrate the role of the external layer composition, in particular the role of proteins more than that of hydrophobicity, on their adhesion abilities.

Time-of-flight secondary ion mass spectrometry: characterisation of stainless steel surfaces immersed in natural seawater.

Time-of-flight secondary ion mass spectrometry (ToF-SIMS) has been employed to study the biofouling of stainless steel samples immersed in seawater. The aim of these characterisations was to understand the initial mechanisms of biomolecule adsorption for relatively short immersion times (from 0 to 24 h). The results show that: (i) there were unavoidable sample "precontaminations" on the surfaces, despite precaution during their preparation and manipulation (washing, drying and storing); (ii) the major peaks detected were the substrate ones whatever the immersion time [However, some organic (nitrogen and oxygen containing) and inorganic secondary ions appeared and grew with the immersion time.]; (iii) the surface contaminations, the nonuniformity of the adsorbed material so as and bacteria have been clearly observed by high-lateral resolution molecular ToF-SIMS mapping.

Capabilities of static TOF-SIMS in the differentiation of first-row transition metal oxides.

Time-of-flight secondary ion mass spectrometry (TOF-SIMS) analyses were performed on the first-row transition metal oxides from scandium to zinc in positive and negative detection modes. The nature of the numerous M(x)O(y)(+/-) ionic species generated by 15 keV Ga(+) primary ion bombardment allows the identification of a given metal-oxygen system. To identify the metal valence in the oxide under investigation, several procedures were investigated: the detection of specific and characteristic ions, the use of ion abundance ratios and the use of a valence model. Owing to their importance in many fields of materials science, each of these speciation methodologies was evaluated for the differentiation of vanadium, titanium, chromium, manganese, iron, cobalt and copper oxides. Trivalent-hexavalent chromium distinction was first intensely investigated because it really corresponds to a model system for inorganic speciation. For each series of metal oxides, the more pertinent speciation criteria were then systematically tested. The limitations of the proposed methodologies are discussed. Their use is made complicated when pollutants or a superficial oxide layer, with a stoichiometry different from that of the bulk, are present. Finally, thermodynamic considerations relative to the stability of the M(x)O(y)(+/-) ions may also modify the relationship between the analyzed oxide and the observed positive and negative secondary ion mass spectra.