In-depth characterization of phosphate intercalated Mg Al Layered double hydroxides and study of the PO4 release properties.

Slow-release fertilizers (SRFs) form the core of innovative strategies in sustainable agriculture. Layered Double Hydroxides (LDH), known for their high capacity to sequester plant nutrients, especially phosphate, are emerging as promising candidates for SRF synthesis. The phosphate release properties of MgAl LDH (with a targeted Mg/Al ratio of 2.0) intercalated with HPO42- anions were assessed in various aqueous environments. A comprehensive analysis, including in-depth chemical and structural characterizations (ICP-OES, XRD, PDF, 27Al NMR, 31P NMR, FTIR, SEM) of the as-prepared phase unveiled a more intricate composition than anticipated for a pure or ideal Mg2Al-HPO4 LDH, encompassing an excess of intercalated phosphate in conjunction with K+. Beyond the intercalated phosphate, solid state 31P NMR speciation identified multiple HxPO4(-3+x) environments, indicating a portion of the phosphate reacting with intralayer Mg2+ to form K-struvite. Additionally, some phosphates were adsorbed onto the surface of amorphous aluminum hydroxide, a side phase formed during MgAl coprecipitation. The phosphate release demonstrated rapid kinetics, occurring within 6 days. Moreover, the released phosphate increased significantly when reducing the Solid/Liquid (S/L) ratio (58%) and further increasing in the presence of carbonate ions (90%). The released phosphate varied from 12% to 90% under different release conditions, transitioning from water to a 3.33 mM NaHCO3 aqueous solution at a low S/L ratio (from 20 mg LDH per mL to 0.02 mg LDH per mL). The simultaneous release of K+, Mg2+, Al3+ indicated the complete dissolution of the K-struvite and partial dissolution of phosphate intercalated MgAl LDH. These results enhanced our understanding of the mechanism governing phosphate release from MgAl LDH, paving the way for potential phosphate recovery by LDH or for the development of LDH-based SRFs.

Enhanced photocatalytic activity of hydrozincite-TiO2 nanocomposite by copper for removal of pharmaceutical pollutant mefenamic acid in aqueous solution.

Nanocomposites based on hydrozincite-TiO2 and copper-doped HZ-xCu-TiO2 (x = 0.1; 0.25; 0.35) were synthesized in a single step using the urea method. The samples were characterized by XRD, FTIR, SEM/TEM, and DRS. The study of adsorption capacity and photocatalytic efficiency of these nanocomposites have been tested on a pharmaceutical pollutant, mefenamic acid (MFA). Kinetic study of removal of MFA indicates that this pollutant was adsorbed on the surface of the synthesized phases, according to Langmuir's model. Such adsorption proved to be well adapted in a kinetic pseudo-second-order model with capacity of 13.08 mg/g for HZ-0.25Cu-TiO2. Subsequently, the kinetics of photocatalytic degradation under UV-visible irradiation was studied according to several parameters, which allowed us to optimize our experimental conditions. The nanocomposite HZ-0.25Cu-TiO2 showed significant removal efficiency of MFA. Elimination rate reached 100% after 20 min under UV-vis irradiation, and 77% after 7 h under visible light irradiation. Repeatability tests have shown that this nanocomposite is extremely stable after six photocatalytic cycles. By-products of MFA were detected by LC/MS. These photoproducts was produced by three types of reactions of hydroxylation: cyclization and cleavage of the aromatic ring. MFA underwent complete mineralization after 22 h of irradiation in the presence of the HZ-0.25Cu-TiO2.

Sepiolite-Hydrogels: Synthesis by Ultrasound Irradiation and Their Use for the Preparation of Functional Clay-Based Nanoarchitectured Materials.

Sepiolite and palygorskite fibrous clay minerals are 1D silicates featuring unique textural and structural characteristics useful in diverse applications, and in particular as rheological additives. Here we report on the ability of grinded sepiolite to generate highly viscous and stable hydrogels by sonomechanical irradiation (ultrasounds). Adequate drying of such hydrogels leads to low-density xerogels that show extensive fiber disaggregation compared to the starting sepiolite-whose fibers are agglomerated as bundles. Upon re-dispersion in water under high-speed shear, these xerogels show comparable rheological properties to commercially available defibrillated sepiolite products, resulting in high viscosity hydrogels that minimize syneresis. These colloidal systems are thus very interesting as they can be used to stabilize many diverse compounds as well as nano-/micro-particles, leading to the production of a large variety of composites and nano/micro-architectured solids. In this context, we report here various examples showing how colloidal routes based on sepiolite hydrogels can be used to obtain new heterostructured functional materials, based on their assembly to solids of diverse topology and composition such as 2D and 1D kaolinite and halloysite aluminosilicates, as well as to the 2D synthetic Mg,Al-layered double hydroxides (LDH).

Confined Growth of NiAl-Layered Double Hydroxide Nanoparticles Within Alginate Gel: Influence on Electrochemical Properties.

NiAl Layered Double Hydroxide (LDH) alginate bionanocomposites were synthesized by confined coprecipitation within alginate beads. The NiAl based bionanocomposites were prepared either by impregnation by divalent and trivalent metal cations of pre-formed calcium cross-linked alginate beads or by using the metal cations (Ni2+, Al3+) as crosslinking cationic agents for the biopolymer network. The impregnation step was systematically followed by a soaking in NaOH solution to induce the LDH coprecipitation. Powder x-ray diffraction (PXRD), infrared spectroscopy (FTIR), energy dispersive X-ray analysis (EDX), thermogravimetry analysis (TGA), electron microscopies (SEM and TEM) confirmed the biotemplated coprecipitation of LDH nanoparticles ranging from 75 to 150 nm for both strategies. The drying of the LDH@alginate beads by supercritical CO2 drying process led to porous bionanocomposite aerogels when Ca2+ cross-linked alginate beads were used. Such confined preparation of NiAl LDH was extended to bionanocomposite films leading to similar results. The permeability and the electrochemical behavior of these NiAl@alginate bionanocomposites, as thin films coated on indium tin oxide (ITO) electrodes, were investigated by cyclic voltammetry, demonstrating an efficient diffusion of the K4Fe(CN)6 redox probe through the LDH@alginate based films and the improvement of the electrochemical accessibility of the Ni sites.

Synthesis and Structural Characterization of a Pure ZnAl4(OH)12(SO4)·2.6H2O Layered Double Hydroxide.

The phase purity of a series of ZnAl4(OH)12SO4· nH2O layered double hydroxides (ZnAl4-LDH) obtained from a reaction of bayerite (Al(OH)3) with an excess of zinc(II) sulfate under hydrothermal conditions was investigated as a function of the reaction temperature, the duration of the hydrothermal treatment, and the zinc(II) concentration. The product quality, i.e., crystalline impurities, Al impurities, and bulk Zn:Al ratio, were assessed by powder X-ray diffraction (PXRD), 27Al MAS NMR, and elemental analysis. Structural characterization of a stoichiometric ZnAl4-LDH (120 °C, 9 days, and 2.8 M Zn(II)) showed a well-defined structure of the metal ion layer as evidenced by a single, well-defined Zn environment: i.e., no Zn substitution on the Al sites according to Zn k-edge EXAFS and PXRD. Furthermore, nearly all of the 12 different 1H atoms in the -OH groups and 4 27Al resonances could be assigned using 1H,27Al NMR correlation experiments recorded with ultrafast MAS. The interlayer water content is variable on the basis of thermogravimetric analysis and changes in the 1H MAS NMR spectra with temperature. A composition of ZnAl4(OH)12(SO4)·2.6H2O was obtained from a combination of these techniques and confirmed that ZnAl4-LDH is isostructural with the mineral nickelalumite (NiAl4(OH)12SO4·3H2O).

Potential Sustainable Slow-Release Fertilizers Obtained by Mechanochemical Activation of MgAl and MgFe Layered Double Hydroxides and K2HPO4.

This study describes the behavior of potential slow-release fertilizers (SRF), prepared by the mechanochemical activation of calcined Mg2Al-CO3 or Mg2Fe-CO3 layered double hydroxides (LDH) mixed with dipotassium hydrogen phosphate (K2HPO4). The effects of LDH thermal treatment on P/K release behavior were investigated. Characterizations of the inorganic composites before and after release experiments combined X-Ray diffraction (XRD), Fourier-transform infra-red spectroscopy (FTIR), solid-state nuclear magnetic resonance (NMR), scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The best release profile (<75% in 28 days and at least 75% release) was obtained for MgAl/K2HPO4 (9 h milling, 2:1 molar ratio, MR). Compared to readily used K2HPO4, milling orthophosphate into LDH matrices decreases its solubility and slows down its release, with 60% and 5.4% release after 168 h for MgAl/K2HPO4 and MgFe/K2HPO4 composites, respectively. Mechanochemical addition of carboxymethylcellulose to the LDH/K2HPO4 composites leads to a noticeable improvement of P release properties.

Assembly of nitroreductase and layered double hydroxides toward functional biohybrid materials.

The development of new multifunctional materials integrating catalytically active and selective biomolecules, such as enzymes, as well as easily removable and robust inorganic supports that allow their use and reuse, is a subject of ongoing attention. In this work, the nitroreductase NfrA2/YncD (NR) from Bacillus megaterium Mes11 strain was successfully immobilized by adsorption and coprecipitation on layered double hydroxide (LDH) materials with different compositions (MgAl-LDH and ZnAl-LDH), particle sizes and morphologies, and using different enzyme/LDH mass ratios (Q). The materials were characterized and the immobilization and catalytic performance of the biohybrids were studied and optimized. The nitroreductase-immobilized on the nanosized MgAl-LDH displayed the best catalytic performance with 42-46% of catalytic retention and>80% of immobilization yield at saturation values of enzyme loading Cs ≈ 0.6 g NR/g LDH (Q = 0.8). The adsorption process displayed high enzyme-LDH affinity interactions yielding to a stable biohybrid material. The increase in the amount of enzyme loading favoured the catalytic performance of the biohybrid due to the better preservation of the native conformation. The biohybrid was reused several times with partial activity retention after 4 cycles. In addition, the biohybrid was successfully dried maintaining the catalytic activity for several weeks when it was stored in its dry form. Finally, thin films of NR@LDH biohybrid deposited on glassy carbon electrodes were evaluated as a modified electrode applied for nitro-compound detection. The results show that these biohybrids can be used in biotechnology applications to efficiently detect compounds such as dinitrotoluene. The search for new non-hazardous chemical designs preventing or reducing the use of aggressive chemical processes for human being and the environment is the common philosophy within sustainable chemistry.

Innovative Electrochemical Screening Allows Transketolase Inhibitors to Be Identified.

Transketolases (TKs) are ubiquitous thiamine pyrophosphate (TPP)-dependent enzymes of the nonoxidative branch of the pentose phosphate pathway. They are considered as interesting therapeutic targets in numerous diseases and infections (e.g., cancer, tuberculosis, malaria), for which it is important to find specific and efficient inhibitors. Current TK assays require important amounts of enzyme, are time-consuming, and are not specific. Here, we report a new high throughput electrochemical assay based on the oxidative trapping of the TK-TPP intermediate. After electrode characterization, the enzyme loading, electrochemical protocol, and substrate concentration were optimized. Finally, 96 electrochemical assays could be performed in parallel in only 7 min, which allows a rapid screening of TK inhibitors. Then, 1360 molecules of an in-house chemical library were screened and one early lead compound was identified to inhibit TK from E. coli with an IC50 of 63 µM and an inhibition constant ( KI) of 3.4 µM. The electrochemical assay was also used to propose an inhibition mechanism.

Interactions between Biological Cells and Layered Double Hydroxides: Towards Functional Materials.

This review highlights the current research on the interactions between biological cells and Layered Double Hydroxides (LDH). The as-prepared biohybrid materials appear extremely attractive in diverse fields of application relating to health care, environment and energy production. We describe how thanks to the main features of biological cells and LDH layers, various strategies of assemblies can be carried out for constructing smart biofunctional materials. The interactions between the two components are described with a peculiar attention to the adsorption, biocompatibilization, LDH layer internalization, antifouling and antimicrobial properties. The most significant achievements including authors' results, involving biological cells and LDH assemblies in waste water treatment, bioremediation and bioenergy generation are specifically addressed.

Design of latex-layered double hydroxide composites by tuning the aggregation in suspensions.

Colloidal stability of polymeric latex particles was studied in the presence of oppositely charged layered double hydroxide (LDH) platelets of different interlayer anions. Adsorption of the LDH particles led to charge neutralization and to overcharging of the latex at appropriate concentrations. Mixing stable colloidal suspensions of individual particles results in rapid aggregation once the LDH adsorption neutralizes the negative charges of the polymer spheres, while stable suspensions were observed at high and low LDH doses. The governing interparticle interactions included repulsive electrical double layer forces as well as van der Waals and patch-charge attractions, whose strength depended on the amount of LDH particles adsorbed on the latex surface. The type of the LDH interlayer anions did not affect the colloidal stability of the samples. Structural investigation of the obtained latex-LDH composites revealed that the polymer spheres were completely coated with the inorganic platelets once their concentration was sufficiently high. These results are especially important for designing synthetic routes for hybrid systems in suspensions, where stable colloids are required for uniform film-formation and for the homogeneous distribution of the inorganic filler within the composite materials.

Thiamine biosensor based on oxidative trapping of enzyme-substrate intermediate.

In the present work, we describe a new thiamine amperometric biosensor based on thiamine pyrophosphate (ThDP)-dependent transketolase (TK)-catalyzed reaction, followed by the oxidative trapping of TK intermediate α,ß-dihydroxyethylthiamine diphosphate (DHEThDP) within the enzymatic active site. For the biosensor design purpose, TK from Escherichia coli (TKec) was immobilized in Mg2Al-NO3 Layered Double Hydroxides (LDH) and the electrochemical detection was achieved with the TKec/LDH modified glassy carbon electrode (GCE). The transduction process was based on the ability of Fe(CN)63- to oxidize DHEThDP to glycolic acid along with ThDP regeneration. The released Fe(CN)64- was re-oxidized at +0.5V vs Ag-AgCl and the reaction was followed by chronoamperometry. The TKec/LDH/GCE biosensor was optimized using the best TK donor substrates, namely l-erythrulose and d-fructose-6-phosphate. ThDP was assayed with great sensitivity (3831mAM-1cm-2) over 20-400nM linear range.

Structural Investigation of Zn(II) Insertion in Bayerite, an Aluminum Hydroxide.

Bayerite was treated under hydrothermal conditions (120, 130, 140, and 150 °C) to prepare a series of layered double hydroxides (LDHs) with an ideal composition of ZnAl4(OH)12(SO4)0.5·nH2O (ZnAl4-LDHs). These products were investigated by both bulk techniques (powder X-ray diffraction (PXRD), transmission electron microscopy, and elemental analysis) and atomic-level techniques ((1)H and (27)Al solid-state NMR, IR, and Raman spectroscopy) to gain a detailed insight into the structure of ZnAl4-LDHs and sample composition. Four structural models (one stoichiometric and three different defect models) were investigated by Rietveld refinement of the PXRD data. These were assessed using the information obtained from other characterization techniques, which favored the ideal (nondefect) structural model for ZnAl4-LDH, as, for example, (27)Al magic-angle spinning NMR showed that excess Al was present as amorphous bayerite (Al(OH)3) and pseudoboehmite (AlOOH). Moreover, no evidence of cation mixing, that is, partial substitution of Zn(II) onto any of four Al sites, was observed. Altogether this study highlights the challenges involved to synthesize pure ZnAl4-LDHs and the necessity to use complementary techniques such as PXRD, elemental analysis, and solid-state NMR for the characterization of the local and extended structure of ZnAl4-LDHs.

High-Density Protein Loading on Hierarchically Porous Layered Double Hydroxide Composites with a Rational Mesostructure.

Hierarchically porous biocompatible Mg-Al-Cl-type layered double hydroxide (LDH) composites containing aluminum hydroxide (Alhy) have been prepared using a phase-separation process. The sol-gel synthesis allows for the hierarchical pores of the LDH-Alhy composites to be tuned, leading to a high specific solid surface area per unit volume available for high-molecular-weight protein adsorptions. A linear relationship between the effective surface area, SEFF, and loading capacity of a model protein, bovine serum albumin (BSA), is established following successful control of the structure of the LDH-Alhy composite. The threshold of the mean pore diameter, Dpm, above which BSA is effectively adsorbed on the surface of LDH-Alhy composites, is deduced as 20 nm. In particular, LDH-Alhy composite aerogels obtained via supercritical drying exhibit an extremely high capacity for protein loading (996 mg/g) as a result of a large mean mesopore diameter (>30 nm). The protein loading on LDH-Alhy is >14 times that of a reference LDH material (70 mg/g) prepared via a standard procedure. Importantly, BSA molecules pre-adsorbed on porous composites were successfully released on soaking in ionic solutions (HPO4(2-) and Cl(-) aqueous). The superior capability of the biocompatible LDH materials for loading, encapsulation, and releasing large quantities of proteins was clearly demonstrated.

Layered Double Hydroxide Nanoclusters: Aqueous, Concentrated, Stable, and Catalytically Active Colloids toward Green Chemistry.

Increasing attention has been dedicated to the development of nanomaterials rendering green and sustainable processes, which occur in benign aqueous reaction media. Herein, we demonstrate the synthesis of another family of green nanomaterials, layered double hydroxide (LDH) nanoclusters, which are concentrated (98.7 g/L in aqueous solvent), stably dispersed (transparent sol for >2 weeks), and catalytically active colloids of nano LDHs (isotropic shape with the size of 7.8 nm as determined by small-angle X-ray scattering). LDH nanoclusters are available as colloidal building blocks to give access to meso- and macroporous LDH materials. Proof-of-concept applications revealed that the LDH nanocluster works as a solid basic catalyst and is separable from solvents of catalytic reactions, confirming the nature of nanocatalysts. The present work closely investigates the unique physical and chemical features of this colloid, the formation mechanism, and the ability to act as basic nanocatalysts in benign aqueous reaction systems.

Thin bacteria/Layered Double Hydroxide films using a layer-by-layer approach.

This paper reports the design of thin bacteria/Layered Double Hydroxides (LDH) films in which bacterial cells of Pseudomonas sp. strain ADP were assembled alternatively with Mg2Al-NO3 LDH nanosheets by a layer-by-layer deposition method. The UV-Vis spectroscopy was used to monitor the assembly process, showing a progressive increase in immobilized bacteria amount upon deposited cycles. The {ADP/LDH}n film was characterized by X-ray diffraction, infrared spectroscopy, scanning electron microscopy and atomic force microscopy. The metabolic activity of immobilized bacteria was determined using chronoamperometry by measuring the biochemical oxygen demand in presence of glucose using an artificial electron acceptor (Fe(CN)6(3-)) at 0.5V/Ag-AgCl. A steady current of 0.250µAcm(-2) was reached in about 30s after the addition of 5mM glucose.

Intercalation and structural aspects of macroRAFT agents into MgAl layered double hydroxides.

Increasing attention has been devoted to the design of layered double hydroxide (LDH)-based hybrid materials. In this work, we demonstrate the intercalation by anion exchange process of poly(acrylic acid) (PAA) and three different hydrophilic random copolymers of acrylic acid (AA) and n-butyl acrylate (BA) with molar masses ranging from 2000 to 4200 g mol-1 synthesized by reversible addition-fragmentation chain transfer (RAFT) polymerization, into LDH containing magnesium(II) and aluminium(III) intralayer cations and nitrates as counterions (MgAl-NO3 LDH). At basic pH, the copolymer chains (macroRAFT agents) carry negative charges which allowed the establishment of electrostatic interactions with the LDH interlayer and their intercalation. The resulting hybrid macroRAFT/LDH materials displayed an expanded interlamellar domain compared to pristine MgAl-NO3 LDH from 1.36 nm to 2.33 nm. Depending on the nature of the units involved into the macroRAFT copolymer (only AA or AA and BA), the intercalation led to monolayer or bilayer arrangements within the interlayer space. The macroRAFT intercalation and the molecular structure of the hybrid phases were further characterized by Fourier transform infrared (FTIR) and solid-state 13C, 1H and 27Al nuclear magnetic resonance (NMR) spectroscopies to get a better description of the local structure.

Effect of MacroRAFT Copolymer Adsorption on the Colloidal Stability of Layered Double Hydroxide Nanoparticles.

The colloidal behavior of layered double hydroxide nanoparticles containing Mg(2+) and Al(3+) ions as intralayer cations and nitrates as counterions (MgAl-NO3-LDH) was studied in the presence of a short statistical copolymer of acrylic acid (AA) and butyl acrylate (BA) terminated with 4-cyano-4-thiothiopropylsulfanyl pentanoic acid (CTPPA) (P(AA7.5-stat-BA7.5)-CTPPA) synthesized by reversible addition-fragmentation chain-transfer (RAFT) polymerization. Surface charge properties and aggregation of the particles were investigated by electrophoresis and dynamic light scattering (DLS), respectively. The negatively charged P(AA7.5-stat-BA7.5)-CTPPA adsorbed strongly on the oppositely charged particles, leading to charge neutralization at the isoelectric point (IEP) and charge reversal at higher copolymer concentrations. The dispersions were unstable, i.e., fast aggregation of the MgAl-NO3-LDH occurred near the IEP while high stability was achieved at higher P(AA7.5-stat-BA7.5)-CTPPA concentrations. Atomic force (AFM) and transmission electron (TEM) microscopy imaging revealed that the platelets preferentially adopted a face-to-face orientation in the aggregates. While the stability of the bare particles was very sensitive to ionic strength, the P(AA7.5-stat-BA7.5)-CTPPA copolymer-coated particles were extremely stable even at high salt levels. Accordingly, the limited colloidal stability of bare MgAl-NO3-LDH dispersions was significantly improved by adding an appropriate amount of P(AA7.5-stat-BA7.5)-CTPPA to the suspension.

Bacteria encapsulated in layered double hydroxides: towards an efficient bionanohybrid for pollutant degradation.

A soft chemical process was successfully used to immobilize Pseudomonas sp. strain ADP (ADP), a well-known atrazine (herbicide) degrading bacterium, within a Mg2Al-layered double hydroxide host matrix. This approach is based on a simple, quick and ecofriendly direct coprecipitation of metal salts in the presence of a colloidal suspension of bacteria in water. It must be stressed that by this process the mass ratio between inorganic and biological components was easily tuned ranging from 2 to 40. This ratio strongly influenced the biological activity of the bacteria towards atrazine degradation. The better results were obtained for ratios of 10 or lower, leading to an enhanced atrazine degradation rate and percentage compared to free cells. Moreover the biohybrid material maintained this biodegradative activity after four cycles of reutilization and 3 weeks storage at 4°C. The ADP@MgAl-LDH bionanohybrid materials were completely characterized by X-ray diffraction (XRD), FTIR spectroscopy, thermogravimetric analysis and scanning and transmission electronic microscopy (SEM and TEM) evidencing the successful immobilization of ADP within the inorganic matrix. This synthetic approach could be readily extended to other microbial whole-cell immobilization of interest for new developments in biotechnological systems.

Heterogeneous photocatalytic degradation of pesticides using decatungstate intercalated macroporous layered double hydroxides.

Decatungstate W10O32(4-) was efficiently intercalated between the layers of three-dimensionally ordered macroporous Mg2Al-layered double hydroxide. The structural and textural properties of as-prepared intercalated compound were characterized using different solid-state characterization techniques such as X-ray powder diffraction, FTIR and Raman spectroscopies and electronic microscopy. The photocatalytic properties of immobilized W10O32 (4-) within Mg2Al structure were investigated using 2-(1-naphthyl) acetamide (NAD) as a model of pesticide. The influence of different parameters such as amount of catalyst, pH and oxygen concentration were investigated. An optimal NAD degradation was obtained for a photocatalyst concentration of 60 mg l(-1). Under our experimental conditions, this heterogeneous photocatalyst induces photodegradation of 60 % of NAD after 17 h of irradiation at 365 nm and at pH 6.6. Interestingly, pesticide photodegradation leads to the mineralization of substrates to H2O and CO2 and the photocatalyst can be recycled and reused without any loss of activity over four cycles.

Hybrid and biohybrid layered double hydroxides for electrochemical analysis.

Layered double hydroxides (LDH) are lamellar materials that have been extensively used as electrode modifiers. Nanostructured organic-inorganic materials can be designed by intercalation of organic or metallic complexes within the interlayer space of these materials or by the formation of composite materials based on biopolymers (alginate or chitosan) or biomolecules, such as enzymes. These hybrid or biohybrid materials have interesting properties applicable in electroanalytical devices. From an exhaustive review of the literature, the relevance of these hybrid and biohybrid LDH materials as electrode materials for electrochemical detection of species with an environmental or health impact is evaluated. The analytical characteristics (sensitivity and detection limit) of LDH-based amperometric sensors or biosensors are scrutinized.