Cross-Linked Polyacrylic-Based Hydrogel Polymer Electrolytes for Flexible Supercapacitors.

Hydrogel polymer electrolytes (GPEs), as an important component of flexible energy storage devices, have gradually received wide attention compared with traditional liquid electrolytes due to their advantages of good mechanical, bending, and safety properties. In this paper, two cross-linked GPEs of poly(acrylic acid-co-acrylamide) or poly(acrylic acid-co-N-methylolacrylamide) with NaNO3 aqueous solution (P(AA-co-AM)/NaNO3 or P(AA-co-HAM)/NaNO3) were successfully prepared using radical polymerization, respectively, using acrylic acid (AA) as the monomer, N-methylolacrylamide (HAM) or acrylamide (AM) as the comonomer, and N, N-methylenebisacrylamide (MBAA) as the cross-linking agent. We investigated the morphology, glass transition temperature (Tg), ionic conductivities, mechanical properties, and thermal stabilities of the two GPEs. By comparison, P(AA-co-HAM)/NaNO3 GPE exhibits a higher ionic conductivity of 2.00 × 10-2 S/cm, lower Tg of 152 °C, and appropriate mechanical properties, which are attributed to the hydrogen bonding between the -COOH and -OH, and moderate cross-linking. The flexible symmetrical supercapacitors were assembled with the two GPEs and two identical activated carbon electrodes, respectively. The results show that the flexible supercapacitor with P(AA-co-HAM)/NaNO3 GPE shows good electrochemical performance with a specific capacitance of 63.9 F g-1 at a current density of 0.2 A g-1 and a capacitance retention of 89.4% after 3000 charge-discharge cycles. Our results provide a simple and practical design strategy of GPEs for flexible supercapacitors with wide application prospects.

Phosphate ester functionalized fluorene-benzothiadiazole alternating copolymer/hydroxylated g-C3N4 heterojunctions for efficient hydrogen evolution under visible-light irradiation.

It is highly desirable to explore functionalized polymer semiconductor/g-C3N4 heterojunction photocatalysts with the tight interfacial connection for promoting the photogenerated electron-hole pair separation, improving the hydrophilicity, extending the visible light response and achieving the efficient visible light-driven H2 evolution. Herein, we synthesized novel poly[9,9-bis(3-ethyl phosphate propyl)fluorene-alt-benzothiadiazole] (PPFBT) with a phosphate ester on every repeating unit by the Suzuki polymerization and then fabricated PPFBT/hydroxylated g-C3N4 (PPFBT/CN-OH) heterojunctions via a surface hydroxyl-induced assembly process. The ratio-optimized 5PPFBT/CN-OH shows the hydrogen evolution activity of 2662.4 µmol·g-1·h-1, an 11.1-time enhancement compared to CN-OH. The improved photocatalytic activity is mainly attributed to the enhanced electron-hole pair separation due to the tight interfacial connection by hydrogen bond (P=O…H-O) and N…S interactions between PPFBT and CN-OH. It is verified that abundant phosphate ester groups of PPFBT improve the hydrophilicity and form coordination bonds with platinum (P=O:Pt) as a cocatalyst to facilitate water splitting for H2 evolution. It is also confirmed that the enhanced electron-hole pair separation is mainly dependent on the excited high-energy level electron transfer from CN-OH to PPFBT. This work provides a rational molecular design strategy for constructing efficient functionalized polymer semiconductor/g-C3N4 heterojunctions for sunlight-driven H2 evolution.

Improved Visible-Light Photocatalytic H2 Evolution of G-C3N4 Nanosheets by Constructing Heterojunctions with Nano-Sized Poly(3-Thiophenecarboxylic Acid) and Coordinating Fe(III).

It is highly desirable to enhance the photogenerated charge separation of g-C3N4 by constructing efficient heterojunctions, especially with an additional organic constitution for solar-hydrogen conversion. Herein, g-C3N4 nanosheets have been modified controllably with nano-sized poly(3-thiophenecarboxylic acid) (PTA) through in situ photopolymerization and then coordinated with Fe(III) via the -COOH groups of modified PTA, forming an interface of tightly contacted nanoheterojunctions between the Fe(III)-coordinated PTA and g-C3N4. The resulting ratio-optimized nanoheterojunction displays a ~4.6-fold enhancement of the visible-light photocatalytic H2 evolution activity compared to bare g-C3N4. Based on the surface photovoltage spectra, measurements of the amount of •OH produced, photoluminescence (PL) spectra, photoelectrochemical curves, and single-wavelength photocurrent action spectra, it was confirmed that the improved photoactivity of g-C3N4 is attributed to the significantly promoted charge separation by the transfer of high-energy electrons from the lowest unoccupied molecular orbital (LUMO) of g-C3N4 to the modified PTA via the formed tight interface, dependent on the hydrogen bond interaction between the -COOH of PTA and the -NH2 of g-C3N4, and the continuous transfer to the coordinated Fe(III) with -OH favorable for connection with Pt as the cocatalyst. This study demonstrates a feasible strategy for solar-light-driven energy production over the large family of g-C3N4 heterojunction photocatalysts with exceptional visible-light activities.

Controlled Synthesis of Nitro-Terminated Oligothiophene/Crystallinity-Improved g-C3N4 Heterojunctions for Enhanced Visible-Light Catalytic H2 Production.

It is highly desired to explore closely contacted polymer semiconductor/g-C3N4 heterojunction photocatalysts with promoted photogenerated-carrier separation and extended visible-light response for efficient visible-light-driven H2 production. Here, we first synthesized the nitro-terminated oligothiophene (OTh) by the controlled copolymerization of thiophene and 2-nitrothiophene monomers, then constructed the nitro-terminated oligothiophene/crystallinity-improved g-C3N4 (OTh/g-C3N4) heterojunctions by a grinding-induced combination strategy. The ratio-optimized 20OTh5/g-C3N4 shows highly efficient H2 production activity up to 3.63 mmol h-1 g-1 under visible-light irradiation, with ∼25.9-time enhancement compared to that of g-C3N4. As verified by time-resolved photoluminescence spectra, surface photovoltage spectra, and the fluorescence spectra related to •OH amounts, the improved photocatalytic activity is due to the promoted photogenerated-carrier transfer and separation in the heterojunctions and the expanded visible-light response. It is also confirmed that the controlled OTh chain length, improved g-C3N4 crystallinity, and tight interface contact dependent on the hydrogen bonds and N···S interactions between OTh and g-C3N4 are reasonable for enhanced photogenerated-carrier separation with the electron transfer from OTh to g-C3N4. This work illustrates a feasible strategy to construct efficient polymer semiconductor/g-C3N4 heterojunction photocatalysts for solar-light-driven H2 production.

Suppressing High-Order Phase for Efficient Pure Red Quasi-2D Perovskite Light-Emitting Diodes.

Quasi-two-dimensional (quasi-2D) perovskites are promising for the realization of spectrally stable pure red perovskite light-emitting diodes (PeLEDs) with a single iodide component, because they avoid the halide separation that red three-dimensional perovskites of mixed halides have faced. However, the distribution of high-order phases in solution-processed quasi-2D perovskite films causes the spectral shift away from the pure red region. Here, we introduced a simple approach of adding excessive ligand combinations to redistribute the phase distribution of quasi-2D perovskite and to inhibit the high-order phase. Appropriate excess organic ligands will not affect charge injection but will keep the efficient energy funneling and passivate the defect. The narrowed phase distribution reduced the band tail state and restrained reverse charge transfer, resulting in enhanced radiation recombination. We obtained efficient and spectrally stable pure red PeLEDs at 638 nm (approaching the Rec. 2020 specification) with a peak EQE of 11.8% and maximum luminance of 1688 cd/cm2. This study provides guidance for future developments of highly efficient pure red PeLEDs.

Tightly intercalated Ti3C2Tx/MoO3-x/PEDOT:PSS free-standing films with high volumetric/gravimetric performance for flexible solid-state supercapacitors.

Ti3C2Tx-MXenes have extremely promising applications in electrochemistry, but the development of Ti3C2Tx is limited due to severe self-stacking problem. Here, we introduced oxygen vacancy-enriched molybdenum trioxide (MoO3-x) with pseudocapacitive properties as the intercalator of Ti3C2Tx and PEDOT with high electronic conductivity as the co-intercalator and conductive binder of Ti3C2Tx to synthesize Ti3C2Tx/MoO3-x/PEDOT:PSS (TMP) free-standing films by vacuum-assisted filtration and H2SO4 soaking. The tightly intercalated free-standing film structure can effectively improve the self-stacking phenomenon of Ti3C2Tx, expose more active sites and facilitate electron/ion transport, thus making TMP show excellent electrochemical performance. The volumetric and gravimetric capacitance of optimized TMP-2 can reach 1898.5 F cm-3 and 523.0 F g-1 at 1 A g-1 with a rate performance of 90.5% at the current density from 1 A g-1 to 20 A g-1, which is significantly better than those of MXene-based composites reported in the literature. The directly-assembled TMP-2//TMP-2 flexible solid-state supercapacitor displays high energy/power output performances (25.1 W h L-1 at 6383.1 W L-1, 6.9 W h kg-1 at 1758.4 W kg-1) and there is no obvious change after 100 cycles at a bending angle of 180°. As a result, the tightly intercalated TMP-2 free-standing film with high volumetric/gravimetric capacitances is a promising material for flexible energy storage devices.

Synergistic effect of defects and porous structure in CoCCHH-CoSe heterogeneous-tube @PEDOT:PSS foam towards elastic supercapacitor with enhanced pseudocapacitances.

It is still challenging to construct stable 3D energy storage materials at the nanoscale by precise pore structure control and reasonable surface modification. Herein, a novel interwoven porous Co(CO3)0.35Cl0.20(OH)1.10 (CoCCHH)-CoSe heterogeneous-tube @PEDOT:PSS 3D foam with abundant active sites is presented as supercapacitor electrodes. The electrochemical results indicated that the pore structure provides ample space for redox reaction, and increases the number of ion transport channels. Besides, rational surface modification brings about sufficient active sites for redox reaction. The stable, porous PEDOT:PSS foam with a 3D elastic frame exhibited excellent electrical conductivity. Thus, the CoCCHH-CoSe@PEDOT:PSS foam possessed excellent specific capacitance and energy density, due to the synergistic effect of the unique 3D structure and surface defects. The home-made supercapacitor with CoCCHH-CoSe@PEDOT:PSS foam as cathode materials showed high specific capacitance (440.6F g-1 at 1 A g-1) and excellent energy density (137.7 Wh kg-1). This work provides a valuable strategy to develop potential materials for electrochemical energy storage.

Spinel LiMn2O4 nanoparticles fabricated by the flexible soft template/Pichini method as cathode materials for aqueous lithium-ion capacitors with high energy and power density.

Spinel LiMn2O4 (LMO) with a three-dimensional structure has become one of the cathode materials that has gained the most interest due to its safety, low price and abundant resources. However, the lithium ion transmission is limited by large particle size and particle agglomeration of LMO. Thus, reducing the particle size and agglomeration of LMO can effectively improve its lithium ion transmission. Here, we synthesized a LMO cathode material with a nanoscale crystal size using the flexible expanded graphite (EG) soft template and Pichini method. EG-controlled particle size and particle agglomeration of LMO is conducive to charge transfer and diffusion of lithium ions between LMO and the electrolyte, meanwhile, there are more redox sites on the nanosized LMO particles, which makes the redox reaction of LMO more thorough during the charge and discharge process, resulting in high capacitance performance. In order to obtain the considerably required lithium-ion capacitors (LICs) with high energy density and power density, we assembled aqueous LMO//activated carbon (AC) LICs with 5 M LiNO3 as the aqueous electrolytes, which are environmentally friendly, safe, low cost and have higher electrical conductivity than organic electrolytes. The optimal LIC has an energy density of 32.63 W h kg-1 at a power density of 500 W kg-1 and an energy density of 8.06 W h kg-1 at a power density of 10 000 W kg-1, which is higher than most of the LMO-based LICs in previous reports. After 2000 cycles, the specific capacitance retention rate was 75.9% at a current density of 3 A g-1. Therefore, our aqueous LMO//AC LICs synthesized by the soft template/Pichini method have wide prospects and are suitable for low-cost, high-safety and high-power applications.

Mg-O-Bridged Polypyrrole/g-C3 N4 Nanocomposites as Efficient Visible-Light Catalysts for Hydrogen Evolution.

It is highly desired to improve the visible-light activity of g-C3 N4 for H2 evolution by constructing closely contacted heterojunctions with conductive polymers. Herein, a polymer nanocomposite photocatalyst with high visible-light activity is fabricated successfully by coupling nanosized polypyrrole (NPPy) particles onto g-C3 N4 nanosheets through a simple wet-chemical process, and its visible-light activity is improved further by constructing Mg-O bridges between the NPPy and g-C3 N4 . The amount-optimized bridged nanocomposite displays an approximately ninefold improvement in visible-light activity compared with g-C3 N4 . On the basis of transient-state surface photovoltage responses, photoluminescence spectra, . OH amount evaluation, and photoelectrochemical curves, it is concluded that the exceptional photoactivity can be attributed to the significantly promoted charge transfer and separation along with visible photosensitization from NPPy. Interestingly, it is confirmed that the promoted charge separation depends mainly on the excited high-level electron transfer from g-C3 N4 to NPPy by single-wavelength photocurrent action spectra. This work provides a feasible strategy for designing polymer nano-heterojunction photocatalysts with exceptional visible-light activities.

Boron/nitrogen co-doped carbon synthesized from waterborne polyurethane and graphene oxide composite for supercapacitors.

We report B/N co-doped carbon materials synthesized by an efficient and easy one-step carbonization method with ferric catalyst treatment from a precursor with boric acid treatment after the formation of the composite between waterborne polyurethane (WPU) and graphene oxide (GO). The nitrogen content was improved with the introduction of numerous melamine in the synthetic process of WPU. In addition, WPU possessed a repetitive basic unit urethane bond (-NHCOO); thus, nitrogen heteroatom could be efficiently introduced into the WPU/GO composite from WPU as a nitrogen-rich carbon. In addition, the specific surface area was increased by the boric acid treatment and washing process. The ferric catalyst treatment could prevent the formation of inert B-N bonds. Thus, the synthesized B/N co-doped carbon materials exhibited high specific capacitance (330 F g-1 at 0.5 A g-1), superior rate performance, and excellent cycling stability. Furthermore, the assembled symmetric supercapacitor displayed a good energy density (7.9 W h kg-1 at 505 W kg-1) and a good capacitance retention of about 89.9% after 5000 charge-discharge cycles in 6 M KOH electrolyte. Therefore, the as-prepared B/N co-doped carbon materials show a promising future in supercapacitor application.

One-step fabrication of nanosized LiFePO4/expanded graphite composites with a particle growth inhibitor and enhanced electrochemical performance of aqueous Li-ion capacitors.

It is reported that olivine-type lithium iron phosphate (LFP) for Li-ion batteries is one of the most widely utilized cathode materials, but its high-power applications are limited due to its intrinsically poor ion transfer rate and conductivity. Therefore, it is highly desired to fabricate LFP Li-ion capacitors (LICs) with high power performance and excellent cyclic reversibility, especially in safe, low cost and environmentally friendly aqueous electrolytes. Here, we fabricate LFP/expanded graphite (EG) nanocomposites by a one-step process, in which polyethylene glycol (PEG) is used as the particle growth inhibitor combined with vacuum infiltration of the LFP precursor into EG as a conductive sub-phase, and further investigate their high-power performance in aqueous LICs. Embedding spherical LFP nanoparticles with well-controlled size and agglomeration into the pores of EG and wrapping LFP nanoparticles by EG films contribute to the rapid electron and ion diffusion in LFP/EG composites, resulting in excellent cyclic reversibility and rate performance of LFP/EG composites. The aqueous LFP/EG//active carbon (AC) LICs were assembled in LiNO3 electrolytes with LFP/EG composites and AC as the positive and negative electrodes, respectively. The optimal LIC shows a power density of 2367.9 W kg-1 at an energy density of 6.5 W h kg-1, dramatically favorable rate characteristics and excellent cycle life with 82.1% capacitance retention of its primary capacitance at 2 A g-1 after 6000 cycles, markedly higher than those of the commercial LFP LIC. The presented aqueous LFP/EG//AC LICs with excellent electrochemical performance are expected to have broad high-power appliances that are cost-sensitive and highly secure.

In-depth proteomic analysis of the byssus from marine mussel Mytilus coruscus.

UNLABELLED: Mussels attach to various submerged surfaces by using the byssus, which contains different proteins and is a promising source of water-resistant bio-adhesives for potential use in biotechnological and medical applications. The protein composition of the byssus has not yet been fully understood although at least eleven byssal proteins were characterized previously. In order to increase genomic resources and identify new byssal proteins from mussel Mytilus coruscus, high-throughput Illumina sequencing was undertaken on the foot, and 79,997,776 paired-ends reads were generated, yielding a library containing 88,825ft unigenes. The M. coruscus byssus was divided into three parts, the proximal thread, the distal thread, and the plaque. Byssal proteins from each part of the byssus were analyzed by shotgun-LTQ analysis. The MS/MS spectra were searched against the foot unigenes dataset and 48 byssal proteins were identified from the M. coruscus byssus. From the whole set, 17, 5, and 11 proteins were exclusive to the proximal thread, the distal thread, and the plaque, respectively. These data can be used as a resource for further studies on the roles of byssal proteins in the deposition of different byssus parts (thread vs. plaque) or in the different mechanical properties (tenacity vs. adhesion). BIOLOGICAL SIGNIFICANCE: Byssal proteins are the major component that controls different aspects of the byssal formation process and thus a source of bioactive molecules that would offer interesting perspectives in biomaterials and bio-adhesive fields. In this paper, we characterized the protein set from different partsof Mytilus coruscus byssus by a combination of transcriptome/proteome technical. A whole set of 48 byssal proteins were described here, including proteins of collagen-like, C1q domain-containing, protease inhibitor-like, tyrosinase-like, SOD, and others. Thread (the distal portion and the proximal portion) and plaque showed distinct protein composition. Of the whole byssal protein set, 11 are exclusive to the plaque, 17 are exclusive to the proximal thread, and 5 are exclusive to the distal thread. Only four proteins are shared by all the three parts of the byssus. The new byssal proteins reported here represent a significant expansion of the knowledge base of Mytilus byssal proteins, and are important for further exploring the mechanism of adhesion in mussel.

Lithium Titanate Confined in Carbon Nanopores for Asymmetric Supercapacitors.

Porous carbons suffer from low specific capacitance, while intercalation-type active materials suffer from limited rate when used in asymmetric supercapacitors. We demonstrate that nanoconfinement of intercalation-type lithium titanate (Li4Ti5O12) nanoparticles in carbon nanopores yielded nanocomposite materials that offer both high ion storage density and rapid ion transport through open and interconnected pore channels. The use of titanate increased both the gravimetric and volumetric capacity of porous carbons by more than an order of magnitude. High electrical conductivity of carbon and the small size of titanate crystals allowed the composite electrodes to achieve characteristic charge and discharge times comparable to that of the electric double-layer capacitors. The proposed composite synthesis methodology is simple, scalable, and applicable for a broad range of active intercalation materials, while the produced composite powders are compatible with commercial electrode fabrication processes.

In-depth proteomic analysis of nacre, prism, and myostracum of Mytilus shell.

Mytilus is an economically important bivalve and its shell is a biomineralized tissue with various microstructures/layers. In the present study, the shell of marine mussel, Mytilus coruscus, was analyzed and three shell layers with different morphologies and polymorphs were observed, which includes nacre, fibrous prism, and myostracum strongly attached by adductor muscles to the interior of the shell surface. In order to understand whether these different shell layers contain different shell matrix proteins (SMPs), the transcriptome sequencing of M. coruscus mantle and a parallel proteomic analysis of SMPs in the three shell layers were performed. A combination of LC-MS/MS analysis with the mantle transcriptome dataset search resulted in the identification of a total of 63 proteins from M. coruscus shell. From this protein set, fifteen, fourteen, and eight proteins were found to be unique to nacre, fibrous prism, and myostracum layers, respectively. In addition, many novel shell proteins were also identified. The data in this study could be used as a background to explore the roles of SMPs in the deposition of different shell layers (nacre vs. fibrous prism vs. myostracum), the different polymorphisms of calcium carbonate (aragonite vs. calcite); and further, the identified proteins from the myostracum could provide candidates for studying the mechanism of adductor muscle-shell attachment. BIOLOGICAL SIGNIFICANCE: In this paper, we characterized for the first time the protein set from different shell layers in Mytilus. Shell matrix proteins are the major component that controls different aspects of the shell formation process and thus a source of bioactive molecules that would offer interesting perspectives in biomaterials and biomedical fields. Our data can be used as a resource for further exploring the roles of shell matrix proteins in the deposition of different shell layers (nacre vs. fibrous prism vs. myostracum) or different polymorphisms of calcium carbonate (aragonite vs. calcite), and the identified protein set of myostracum provided candidates for studying the mechanism of adductor muscle-shell attachment.

Characterization of a novel antimicrobial peptide with chitin-biding domain from Mytilus coruscus.

Using reverse phase high performance liquid chromatography (RP-HPLC), a novel antimicrobial peptide with 55 amino acid residues was isolated from the hemolymph of Mytilus coruscus. This new antimicrobial peptide displays predominant antimicrobial activity against fungi and Gram-positive bacteria. The molecular mass and the N-terminal sequence of this peptide were analyzed by Mass Spectrometry and Edman degradation, respectively. This antimicrobial peptide, with molecular mass of 6621.55 Da, is characterized by a chitin-biding domain and by 6 Cysteine residues engaged in three intra-molecular disulfide bridges. The full-length of cDNA sequence of this new peptide was obtained by rapid amplification of cDNA ends (RACE) and the encoded precursor was turn out to be a chitotriosidase-like protein. Therefore, we named the precursor with mytichitin-1 and the new antimicrobial peptide (designated as mytichitin-CB) is the carboxyl-terminal part of mytichitin-1. The mRNA transcripts of mytichitin-1 are mainly detected in gonad and the expression level of mytichitin-1 in gonad was up-regulated and reached the highest level at 12 h after bacterial challenge, which was 9-fold increase compared to that of the control group. These results indicated that mytichitin-1 was involved in the host immune response against bacterial infection and might contribute to the clearance of invading bacteria.

Fabrication and photoluminescence of hyperbranched silicon nanowire networks on silicon substrates by laser-induced forward transfer.

The structure and photoluminescent properties of films obtained by modified laser-induced forward transfer of silicon are presented. Strong variations in structure with ambient gas composition are observed: in Ar, porous films of mutually agglomerated silicon nanoparticles are observed, while in air the films consist of a network of hyperbranched nanowires (SiHBNWs) whose diameter varies periodically along their length, and which are composed of crystalline silicon nanoparticles surrounded and interconnected by amorphous silicon oxide of varying stoichiometry. The mechanisms of formation of the structures are dwelt upon and explained in term of dynamics within the plume. For the SiHBNWs, the pioneering use of fluorescence imaging was employed to obtain evidence for the photoluminescence originating from the crystalline nanoparticles themselves, and origins of the emission bands are thus attributed to radiative recombination of excitons at the Si/SiO(2) interface accordingly.