RESUMO
Hydrothermal carbonization (HTC) increasingly appears as an eco-friendly method for managing food waste (FW). In this work, a combination of FW was subjected to HTC, and products were critically evaluated. This involved a lab-scale pressure reactor and optimization of HTC conditions: temperature (220-340 °C) and residence time (90-260 min) via central composite design type of response surface methodology (CCD-RSM). Results showed varying temperatures and residence time to impact the hydrochar (HC) and hydrothermal carbonization aqueous phase (HTC-AP) properties. Although HC produced through HTC exhibited lower ash content (<2%) despite higher fixed carbon (>55 %) with respect to the raw FW, the heating value of HC ranged from 19.2 to 32.5 MJ/kg. Temperature primarily influenced FW conversion, affecting carbonaceous properties. Saturated fatty acids (SFA) were found to be predominant in the HTC-AP under all tested operating conditions (77.3, 48.4, and 37.1 wt% for HTC at 340, 280, and 220 °C in 180 min, respectively). Total phosphorus recovery in HC and HTC-AP respectively peaked at 340 °C and 220 °C in 180 min. The study concludes that HTC holds promise for energy-dense biofuel production, nutrient recovery, and fostering a circular economy.
RESUMO
The research impact of catalysts on the hydrothermal carbonization (HTC) process remains an ongoing debate, especially regarding the quest to enhance biomass conversion into fuels and chemicals, which requires diverse catalysts to optimize bio-oil utilization. Comprehensive insights and standardized analytical methodologies are crucial for understanding HTC's potential benefits in terms of biomass conversion stages. This review seeks to understand how catalysts enhance the HTC of biomass for liquid fuel and hydrochar production, drawing from the following key sections: (a) catalyst types applied in HTC processes; (b) biochar functionality as a potential catalyst; (c) catalysts increasing the success of HTC process; and (d) catalyst's effect on the morphological and textural character of hydrochar. The performance of activated carbon would greatly increase via catalyst action, which would progress the degree of carbonization and surface modification, alongside key heteroatoms. As catalytic HTC technology advances, producing carbon materials for thermochemical activities will become more cost-effective, considering the ever-growing demands for high-performance thermochemical technologies.
RESUMO
This study employs response surface methodology and a central composite design (CCD) to optimize hydrothermal treatment (HTT) conditions for the valorization of food waste (FW). Lab-scale pressure reactor-based HTT processes are investigated to detect the effects of temperature (220-340 °C) and resident time (90-260 min) on elemental composition and fatty acid recovery in the hydrothermal liquid. Central to the study is the identification of temperature as the primary factor influencing food waste conversion during the HTT process, showcasing its impact on HTT product yields. The liquid fraction, rich in saturated fatty acids (SFA), demonstrates a temperature-dependent trend, with higher temperatures favoring SFA recovery. Specifically, HTT at 340 °C in 180 min exhibits the highest SFA percentages, reaching up to 52.5 wt%. The study establishes HTT as a promising avenue for nutrient recovery, with the liquid fraction yielding approximately 95% at optimized conditions. Furthermore, statistical analysis using response surface methodology predicts the optimal achievable yields for hydrochar and hydrothermal liquid at 6.15% and 93.85%, respectively, obtained at 320 °C for 200 min.
Assuntos
Perda e Desperdício de Alimentos , Eliminação de Resíduos , Alimentos , Ácidos Graxos , Temperatura , CarbonoRESUMO
Pyrolysis and related thermal conversion processes have shown increased research momentum in recent decades. Understanding the underlying thermal conversion process principles alongside the associated/exhibited operational challenges that are specific to biomass types is crucial for beginners in this research area. From an extensive literature search, the authors are convinced that a tutorial review that guides beginners particularly towards pyrolysis implementation, from different biomasses to the thermal conversion process and conditions, is scarce. An effective understanding of pre-to-main pyrolysis stages, alongside corresponding standard methodologies, would help beginners discuss anticipated results. To support the existing information, therefore, this review sought to seek how to navigate pyrolysis implementation, specifically considering factors and thermochemical operating methods for biomass conversion, drawing the ideas from: (a) the evolving nature of the thermal conversion process; (b) the potential inter-relatedness between individual components affecting pyrolysis-based research; (c) pre- to post-pyrolysis' engagement strategies; (d) potential feedstock employed in the thermal conversion processes; (e) the major pre-treatment strategies applied to feedstocks; (f) system performance considerations between pyrolysis reactors; and (g) differentiating between the reactor and operation parameters involved in the thermal conversion processes. Moreover, pre-pyrolysis activity tackles biomass selection/analytical measurements, whereas the main pyrolysis activity tackles treatment methods, reactor types, operating processes, and the eventual product output. Other areas that need beginners' attention include high-pressure process reactor design strategies and material types that have a greater potential for biomass.
RESUMO
The process of anaerobic digestion used for methane production can be enhanced by dosing various additive materials. The effects of these materials are dependent on various factors, including the processed substrate, process conditions, and the type and amount of the additive material. As part of the study, three different materials-iron powder, lime, and milled porous ceramic-were added to the 30-day anaerobic digestion of the brewer's spent grain to improve its performance. Different doses ranging from 0.2 to 2.3 gTS × L-1 were tested, and methane production kinetics were determined using the first-order model. The results showed that the methane yield ranged from 281.4 ± 8.0 to 326.1 ± 9.3 mL × gVS-1, while substrate biodegradation ranged from 56.0 ± 1.6 to 68.1 ± 0.7%. The addition of lime reduced the methane yield at almost all doses by -6.7% to -3.3%, while the addition of iron powder increased the methane yield from 0.8% to 9.8%. The addition of ceramic powder resulted in a methane yield change ranging from -2.6% to 4.6%. These findings suggest that the use of additive materials should be approached with caution, as even slight changes in the amount used can impact methane production.
RESUMO
Economic development and population growth lead to the increased production of chicken manure, which is a problematic organic waste in terms of its amount, environmental threats, and moisture content. In this study, hydrothermal carbonization, an emerging way of waste disposal, was performed on chicken manure to produce an energy-rich material called hydrochar. The effects of hydrothermal carbonization temperature (180, 240, 300 °C) and process time (30, 90, 180 min) were summarized. Proximate and ultimate analysis, as well as low and high heating values were applied both on raw material and derived hydrochars. Additionally, the performance of the process was examined. The obtained results show that hydrothermal carbonization is a feasible method for chicken manure disposal and valorization. Although the process time did not influence the fuel properties of chicken manure considerably, a higher temperature led to a significantly higher heating value, reaching 23,880.67 ± 34.56 J × g-1 at 300 °C and 180 min with an improvement of ~8329 J × g-1 compared with raw chicken manure (15,551.67 J × g-1). Considering the energy gain value, the hydrochar derived at 240 °C in 30 min had the best result. Moreover, the energy consumption for this process was relatively low (124.34 ± 8.29 kJ × g-1). With its still feasible fuel properties and high heating value of 20,267.00 ± 617.83 kJ × g-1, it was concluded that these parameters of chicken manure hydrochar are the most beneficial and present a potential alternative for conventional fuel.
RESUMO
More still needs to be learned regards the relative contamination of heavy metals and pesticide residues, particularly those found in widely consumed Nigerian food crops like cereals, vegetables, and tubers. In this current study, the heavy metals and pesticide residues detectable in widely consumed Nigerian food crops were respectively quantified using atomic absorption spectroscopy (AAS) and gas chromatography (GC). Specifically, the widely consumed Nigerian food crops included cereals (rice, millet, and maize), legume (soybean), tubers (yam and cassava), as well as leaf (fluted pumpkin, Amaranthus leaf, waterleaf, and scent leaf) and fruit vegetables (okro, cucumber, carrot, and watermelon). Results showed that the detected heavy metals included arsenic (As), cadmium (Cd), chromium (Cr), cobalt (Co), iron (Fe), lead (Pb), manganese (Mn), mercury (Hg), and nickel (Ni), whereas the pesticide residues included Aldrin, Carbofuran, g-chlordane, Chlorpyrifos, DichloroBiphenyl, Dichlorodiphenyldichloroethane (DDD), Dichlorodiphenyltrichloroethane (DDT), Dichlorvos, Endosulfan, Heptachlor, Hexachlorobenzene (HCB), Isopropylamine, Lindane, t-nonachlor, and Profenofos. Across the studied food crops, the concentrations of heavy metals and pesticides were varied, with different trends as they largely fell below the established maximum permissible limits, and with some exceptions. Our findings suggest there could be a somewhat gradual decline in the concentration of the heavy metals and pesticide residues of these studied food crops when compared to previously published reports specific to Nigeria. To help substantiate this observation and supplement existing information, further investigations are required into the concentration of these heavy metals and pesticide residues specific to these studied food crops at other parts of the country.
Assuntos
Contaminação de Alimentos/análise , Metais Pesados/análise , Resíduos de Praguicidas/análise , Cromatografia Gasosa , Produtos Agrícolas/química , Nigéria , Espectrofotometria AtômicaRESUMO
The push for non-thermal food processing methods has emerged due to the challenges associated with thermal food processing methods, for instance, high operational costs and alteration of food nutrient components. Non-thermal food processing involves methods where the food materials receive microbiological inactivation without or with little direct application of heat. Besides being well established in scientific literature, research into non-thermal food processing technologies are constantly on the rise as applied to a wide range of food products. Due to such remarkable progress by scientists and researchers, there is need for continuous synthesis of relevant scientific literature for the benefit of all actors in the agro-food value chain, most importantly the food processors, and to supplement existing information. This review, therefore, aimed to provide a technological update on some selected non-thermal food processing methods specifically focused on their operational mechanisms, their effectiveness in preserving various kinds of foods, as revealed by their pros (merits) and cons (demerits). Specifically, pulsed electric field, pulsed light, ultraviolet radiation, high-pressure processing, non-thermal (cold) plasma, ozone treatment, ionizing radiation, and ultrasound were considered. What defines these techniques, their ability to exhibit limited changes in the sensory attributes of food, retain the food nutrient contents, ensure food safety, extend shelf-life, and being eco-friendly were highlighted. Rationalizing the process mechanisms about these specific non-thermal technologies alongside consumer education can help raise awareness prior to any design considerations, improvement of cost-effectiveness, and scaling-up their capacity for industrial-level applications.