Nanomolecularly-induced Effects at Titania/Organo-Diphosphonate Interfaces for Stable Hybrid Multilayers with Emergent Properties.

Nanoscale hybrid inorganic-organic multilayers are attractive for accessing emergent phenomena and properties through superposition of nanomolecularly-induced interface effects for diverse applications. Here, we demonstrate the effects of interfacial molecular nanolayers (MNLs) of organo-diphosphonates on the growth and stability of titania nanolayers during the synthesis of titania/MNL multilayers by sequential atomic layer deposition and single-cycle molecular layer deposition. Interfacial organo-diphosphonate MNLs result in ∼20-40% slower growth of amorphous titania nanolayers and inhibit anatase nanocrystal formation from them when compared to amorphous titania grown without MNLs. Both these effects are more pronounced in multilayers with aliphatic backbone-MNLs and likely related to impurity incorporation and incomplete reduction of the titania precursor indicated by our spectroscopic analyses. In contrast, both MNLs result in two-fold higher titania nanolayer roughness, suggesting that roughening is primarily due to MNL bonding chemistry. Such MNL-induced effects on inorganic nanolayer growth rate, roughening, and stability are germane to realizing high-interface-fraction hybrid nanolaminate multilayers.

Shuttling Active Elements in and out of Ultrathin Nanowires: Toward Rational Design of Multicomponent Catalysts.

One-dimensional nanostructures, with a high ratio of surface-bulk atoms, find applications as active catalysts. Here, we report tunability in ultrathin single-crystalline AuPdPt nanowires by modifying synthesis conditions and postsynthetic treatment in a controlled ambient atmosphere. The surface microstructure modification of these nanostructures has been analyzed by integrating the results of three crucial techniques including Z-contrast HAADF-STEM imaging, X-ray photoelectron spectroscopy, and electrochemically active surface area from cyclic voltammograms.

Hybrid Aeromaterials for Enhanced and Rapid Volumetric Photothermal Response.

Conversion of light into heat is essential for a broad range of technologies such as solar thermal heating, catalysis and desalination. Three-dimensional (3D) carbon nanomaterial-based aerogels have been shown to hold great promise as photothermal transducer materials. However, until now, their light-to-heat conversion is limited by near-surface absorption, resulting in a strong heat localization only at the illuminated surface region, while most of the aerogel volume remains unused. We present a fabrication concept for highly porous (>99.9%) photothermal hybrid aeromaterials, which enable an ultrarapid and volumetric photothermal response with an enhancement by a factor of around 2.5 compared to the pristine variant. The hybrid aeromaterial is based on strongly light-scattering framework structures composed of interconnected hollow silicon dioxide (SiO2) microtubes, which are functionalized with extremely low amounts (in order of a few µg cm-3) of reduced graphene oxide (rGO) nanosheets, acting as photothermal agents. Tailoring the density of rGO within the framework structure enables us to control both light scattering and light absorption and thus the volumetric photothermal response. We further show that by rapid and repeatable gas activation, these transducer materials expand the field of photothermal applications, like untethered light-powered and light-controlled microfluidic pumps and soft pneumatic actuators.

Thermal History-Dependent Current Relaxation in hBN/MoS2 van der Waals Dimers.

Combining atomically thin layers of van der Waals (vdW) materials in a chosen vertical sequence is an emerging route to create devices with desired functionalities. While this method aims to exploit the individual properties of partnering layers, strong interlayer coupling can significantly alter their electronic and optical properties. Here we explored the impact of the vdW epitaxy on electrical transport in atomically thin molybdenum disulfide (MoS2) when it forms a vdW dimer with crystalline films of hexagonal boron nitride (hBN). We observe a thermal history-dependent long-term (over ∼40 h) current relaxation in the overlap region of MoS2/hBN heterostructures, which is absent in bare MoS2 layers (or homoepitaxial MoS2/MoS2 dimers) on the same substrate. Concurrent relaxation in the low-frequency Raman modes in MoS2 in the heterostructure region suggests a slow structural relaxation between trigonal and octahedral polymorphs of MoS2 as a likely driving mechanism that also results in inhomogeneous charge distribution in the MoS2 layer. Our experiment yields an aspect of vdW heteroepitaxy that can be generic to electrical devices with atomically thin transition-metal dichalcogenides.

Ultrathin Au-Alloy Nanowires at the Liquid-Liquid Interface.

Ultrathin bimetallic nanowires are of importance and interest for applications in electronic devices such as sensors and heterogeneous catalysts. In this work, we have designed a new, highly reproducible and generalized wet chemical method to synthesize uniform and monodispersed Au-based alloy (AuCu, AuPd, and AuPt) nanowires with tunable composition using microwave-assisted reduction at the liquid-liquid interface. These ultrathin alloy nanowires are below 4 nm in diameter and about 2 µm long. Detailed microstructural characterization shows that the wires have an face centred cubic (FCC) crystal structure, and they have low-energy twin-boundary and stacking-fault defects along the growth direction. The wires exhibit remarkable thermal and mechanical stability that is critical for important applications. The alloy wires exhibit excellent electrocatalytic activity for methanol oxidation in an alkaline medium.

Crumpled sheets of reduced graphene oxide as a highly sensitive, robust and versatile strain/pressure sensor.

Sensing of mechanical stimuli forms an important communication pathway between humans/environment and machines. The progress in such sensing technology has possible impacts on the functioning of automated systems, human machine interfacing, health-care monitoring, prosthetics and safety systems. The challenges in this field range from attaining high sensitivity to extreme robustness. In this article, sensing of complex mechanical stimuli with a patch of taped crumpled reduced graphene oxide (rGO) has been reported which can typically be assembled under household conditions. The ability of this sensor to detect a wide variety of pressures and strains in conventional day-to-day applications has been demonstrated. An extremely high gauge factor (∼103) at ultralow strains (∼10-4) with fast response times (<20.4 ms) could be achieved with such sensors. Pressure resulting from a gentle touch to over human body weight could be sensed successfully. The capability of the sensor to respond in a variety of environments could be exploited in the detection of water and air pressures both below and above atmospheric, with a single device.

New insights into electronic and geometric effects in the enhanced photoelectrooxidation of ethanol Using ZnO nanorod/ultrathin Au nanowire hybrids.

Oxidation of small organic molecules in a fuel cell is a viable method for energy production. However, the key issue is the development of suitable catalysts that exhibit high efficiencies and remain stable during operation. Here, we demonstrate that amine-modified ZnO nanorods on which ultrathin Au nanowires are grown act as an excellent catalyst for the oxidation of ethanol. We show that the modification of the ZnO nanorods with oleylamine not only modifies the electronic structure favorably but also serves to anchor the Au nanowires on the nanorods. The adsorption of OH(-) species on the Au nanowires that is essential for ethanol oxidation is facilitated at much lower potentials as compared to bare Au nanowires leading to high activity. While ZnO shows negligible electrocatalytic activity under normal conditions, there is significant enhancement in the activity under light irradiation. We demonstrate a synergistic enhancement in the photoelectrocatalytic activity of the ZnO/Au nanowire hybrid and provide mechanistic explanation for this enhancement based on both electronic as well as geometric effects. The principles developed are applicable for tuning the properties of other metal/semiconductor hybrids with potentially interesting applications beyond the fuel cell application demonstrated here.

New insights into selective heterogeneous nucleation of metal nanoparticles on oxides by microwave-assisted reduction: rapid synthesis of high-activity supported catalysts.

Microwave-based methods are widely employed to synthesize metal nanoparticles on various substrates. However, the detailed mechanism of formation of such hybrids has not been addressed. In this paper, we describe the thermodynamic and kinetic aspects of reduction of metal salts by ethylene glycol under microwave heating conditions. On the basis of this analysis, we identify the temperatures above which the reduction of the metal salt is thermodynamically favorable and temperatures above which the rates of homogeneous nucleation of the metal and the heterogeneous nucleation of the metal on supports are favored. We delineate different conditions which favor the heterogeneous nucleation of the metal on the supports over homogeneous nucleation in the solvent medium based on the dielectric loss parameters of the solvent and the support and the metal/solvent and metal/support interfacial energies. Contrary to current understanding, we show that metal particles can be selectively formed on the substrate even under situations where the temperature of the substrate is lower than that of the surrounding medium. The catalytic activity of the Pt/CeO(2) and Pt/TiO(2) hybrids synthesized by this method for H(2) combustion reaction shows that complete conversion is achieved at temperatures as low as 100 °C with Pt-CeO(2) catalyst and at 50 °C with Pt-TiO(2) catalyst. Our method thus opens up possibilities for rational synthesis of high-activity supported catalysts using a fast microwave-based reduction method.

Thermal stability of spherical nanoporous aggregates and formation of hollow structures by sintering--a phase-field study.

Nanoporous structures are widely used for many applications and hence it is important to investigate their thermal stability. We study the stability of spherical nanoporous aggregates using phase-field simulations that explore systematically the effect of grain boundary diffusion, surface diffusion, and grain boundary mobility on the pathways for microstructural evolution. Our simulations for different combinations of surface and GB diffusivity and GB mobility show four distinct microstructural pathways en route to 100% density: multiple closed pores, hollow shells, hollow shells with a core, and multiple interconnected pores. The microstructures from our simulations are consistent with experimental observations in several different systems. Our results have important implications for rational synthesis of hollow nanostructures or aggregates with open pores, and for controlling the stability of nanoporous aggregates that are widely used for many applications.