Quantifying Strain via Buckling Instabilities in Surface Modified Polymer Brushes.

A compressive strain applied to bilayer films (e.g. thin film adhered to a thick substrate) can lead to buckled or wrinkled morphologies, which has many important applications in stretchable electronics, anti-counterfeit technology, and high-precision micro and nano-metrology. A number of buckling-based metrology methods have been developed to quantify the residual stress and viscoelastic properties of polymer thin films. However, in some systems (e.g. solvent-induced swelling or thermal strain), the compressive strain is unknown or difficult to measure. We present a quantitative method of measuring the compressive strain of wrinkled polymer films and coatings with knowledge of the "skin" thickness, wrinkle wavelength, and wrinkle amplitude. The derived analytical expression is validated with a well-studied model system, e.g., stiff, thin film (PS) bonded to a thick, compliant substrate (PDMS). After validation, we use our expression to quantify the applied swelling strain of previously reported wrinkled poly(styrene-alt-maleic anhydride) brush surfaces. Finally, the applied strain is used to rationalize the observed persistence length of aligned wrinkles created during atomic force microscopy (AFM) lithography and subsequent solvent exposure.

Selective and Rapid Light-Induced RAFT Single Unit Monomer Insertion in Aqueous Solution.

The photocatalyst Zn(II) meso-tetra(4-sulfonatophenyl)porphyrin (ZnTPPS) is found to substantially accelerate visible-light-initiated (red, yellow, green light) single unit monomer insertion (SUMI) of N,N-dimethylacrylamide into the reversible addition-fragmentation chain transfer (RAFT) agent, 4-((((2-carboxyethyl)thio)carbonothioyl)thio)-4-cyanopentanoic acid (RAFT1 ), in aqueous solution. Thus, under irradiation with red (633 nm) or yellow (593 nm) light with 50 mpm (moles per million mole of monomer) ZnTPPS at 30 °C, the rate enhancement provided by photoinduced energy or electron transfer (PET) is ≈sevenfold over the rate of direct photoRAFT-SUMI (without catalyst), which corresponds to achieving full and selective reaction in hours versus days. Importantly, the selectivity, as judged by the absence of oligomers, is retained. Under green light at similar power, higher rates of SUMI are also observed. However, the degree of enhancement provided by PET-RAFT-SUMI over direct photoRAFT-SUMI as a function of catalyst concentration is less and some oligomers are formed.

Sequential and one-pot post-polymerization modification reactions of thiolactone-containing polymer brushes.

Thiolactone chemistry has garnered significant attention as a powerful post-polymerization modification (PPM) route to mutlifunctional polymeric materials. Here, we apply this versatile chemistry to the fabrication of ultrathin, multifunctional polymer surfaces via aminolysis and thiol-mediated double modifications of thiolactone-containing polymer brushes. Polymer brush surfaces were synthesized via microwave-assisted surface-initiated polymerization of DL-homocysteine thiolactone acrylamide. Aminolysis and thiol-Michael double modifications of the thiolactone-functional brush were explored using both sequential and one-pot reactions with bromobenzyl amine and 1H,1H-perfluoro-N-decyl acrylate. X-ray photoelectron spectroscopy and argon gas cluster ion sputter depth profiling enabled quantitative comparison of the sequential and one-pot PPM routes with regard to conversion and spatial distribution of functional groups immobilized throughout thickness of the brush. While one-pot conditions proved to be more effective in immobilizing the amine and acrylate within the brush, the sequenital reaction enabled the fabrication of multifunctional, micropattterned brush surfaces using reactive microcontact printing.

Fabrication of single-chain nanoparticles through the dimerization of pendant anthracene groups via photochemical upconversion.

We report on the use of visible light as the driving force for the intramolecular dimerization of pendant anthracene groups on a methacrylic polymer to induce the formation of single-chain nanoparticles (SCNPs). Using a 532 nm green laser light source and platinum octaethylporphyrin as a sensitizer, we first demonstrated the use of TTA-UC to dimerize monomeric anthracene, and subsequently applied this concept to dilute poly((methyl methacrylate)-stat-(anthracenyl methacrylate)) samples. A combination of triple-detection size-exclusion chromatography, atomic force microscopy, and UV-visible spectroscopy confirmed the formation of the SCNPs. This report pioneers the use of TTA-UC to drive photochemical reactions in polymeric systems, and showcases the potential for TTA-UC in the development of nanoobjects.

Buckling Instabilities in Polymer Brush Surfaces via Postpolymerization Modification.

We report a simple route to engineer ultrathin polymer brush surfaces with wrinkled morphologies using post-polymerization modification (PPM), where the length scale of the buckled features can be tuned from hundreds of nanometers to one micrometer using PPM reaction time. We show that partial crosslinking of the outer layer of the polymer brush under poor solvent conditions is critical to obtain wrinkled morphologies upon swelling. Characterization of the PPM kinetics and swelling behavior via ellipsometry and the through-thickness composition profile via time-of-flight secondary ion mass spectroscopy (ToF-SIMS) provided keys insight into parameters influencing the buckling behavior.