Comprehensive study of retention influencing gas chromatographic parameters affecting linear retention indices.

Retention in gas chromatographic systems has a central role in the identification of compounds even if detectors providing spectral information are used. But linear retention indices (LRI) of a single compound originating from multiple sources tend to vary greatly, probably due to differences in the experimental settings of the determinations. The effect of gas chromatographic parameters on LRI has been investigated using 41 compounds - previously identified from food contact plastics - and n-alkanes (n-C7-n-C40) used as reference series. As the reproducibility of LRIs under the same conditions is generally very good, the smallest changes in the settings often caused statistically significant, though irrelevant changes in the LRI values. Therefore, a multicriterial scoring-ranking system has been worked out to highlight the LRI value differences. Our results highlight that column length, heating rate, and film thickness can all be the reasons of the varying published LRI values. We also demonstrated that for the reproduction of LRI data, the chemistry (and not simply the polarity) of the stationary phase is crucial.

Solubility determination as an alternative to migration measurements.

Solubility values for six UV stabilisers (Cyasorb UV-1164, Tinuvin P, Tinuvin 234, Tinuvin 326, Tinuvin 327 and Tinuvin 1577) and five antioxidants (Irgafos 168, Irganox 1010, Irganox 3114, Irganox 3790 and Irganox 565) were determined in all the liquid food simulants (3% (m/V) acetic acid-water mixture, 10% (V/V), 20% (V/V), 50% (V/V) ethanol-water mixture and vegetable oil) proposed in European Union Regulation No. 10/2011/EC, as well as in fruit juice and cola drink. The applied method was obtained by modification of the method for the determination of water solubility as described in OECD guideline Test No. 105. By using ultrasonication and shorter equilibration time, the time demand of the solubility determinations were decreased notably. Solubility values proved to be lower than the specific migration limits (as specified in 10/2011/EC) at 25 °C for almost all target compounds in food simulants A, B, C and D1 as well as in fruit juice and cola drink. The exceptions were Tinuvin P and Irganox 3790 in simulant D1. The solubility in food simulant D2 was higher than 1000 µg ml(-1) for all target compounds. These results show that the solubility of some additives in food simulants can be so low that it makes migration studies for certain additive-food simulant pairs dispensable.

Migration of Tinuvin P and Irganox 3114 into milk and the corresponding authorised food simulant.

Migration of Tinuvin P (UV stabiliser) and Irganox 3114 (antioxidant) from high-density polyethylene (HDPE) was studied. HDPE pieces were soaked in either milk (1.5% or 3.5% fat content) or 50% (v/v) ethanol-water mixture - the food simulant for milk as specified in Regulation No. 10/2011/EC. The obtained extracts were analysed by LC-MS/MS. For statistical assessment variography was used. It proved to be a useful tool for making a distinction between the early migration range and the equilibrium, despite the variance of the data. Regulation No. 10/2011/EC specifies 10 days of contact time for milk at 5°C. Our experiments with the food simulant with 24 dm(2) kg(-1) surface/mass ratio showed that both Tinuvin P and Irganox 3114 need less than 1 h to reach equilibrium. Furthermore, 10-day experiments with daily sampling showed that these additives are stable in milk, as well as in the food simulant. The effect of the concentration of the additives in HDPE was studied in the 0.01-5% (m/m) range. For both Tinuvin P and Irganox 3114 and all three extractants the migrated amount became independent of the concentration of the additive in the HDPE approximately at 1% (m/m). For Tinuvin P the food simulant gave a close estimate for the milk samples. However, using the food simulant for modelling the migration of Irganox 3114 into milk gave an overestimation with a factor of minimum 3.5. In the case of Tinuvin P special care must be taken, since the recommended amount in the HDPE can result in additive concentrations near or even over the specific migration limit (SML). However, Irganox 3114 cannot reach the SML either in milk or in the food simulant.

Analysis of potential migrants from plastic materials in milk by liquid chromatography-mass spectrometry with liquid-liquid extraction and low-temperature purification.

A simple and fast analytical method was developed for the determination of six UV stabilizers (Cyasorb UV-1164, Tinuvin P, Tinuvin 234, Tinuvin 326, Tinuvin 327, and Tinuvin 1577) and five antioxidants (Irgafos 168, Irganox 1010, Irganox 3114, Irganox 3790, and Irganox 565) in milk. For sample preparation liquid-liquid extraction with low-temperature purification combined with centrifugation was used to remove fats, proteins, and sugars. After the cleanup step, the sample was analyzed with high-performance liquid chromatography-tandem mass spectrometry (LC-MS/MS). External standard and matrix calibrations were tested. External calibration proved to be acceptable for Tinuvin P, Tinuvin 234, Tinuvin 326, Tinuvin 327, Irganox 3114, and Irganox 3790. The method was successfully validated with matrix calibration for all compounds. Method detection limits were between 0.25 and 10 µg/kg. Accuracies ranged from 93 to 109%, and intraday precisions were <13%.

Development and validation of a liquid chromatographic-tandem mass spectrometric method for determination of eleven coccidiostats in milk.

A reversed phase liquid chromatographic-tandem mass spectrometric method with simple solvent extraction and purification by solid phase extraction (SPE) has been developed for the determination of coccidiostats in milk. For sample preparation matrix solid phase dispersion, extraction by organic solvent and SPE with different cartridges were also tested. The compounds determined include lasalocid, narasin, salinomycin, monensin, semduramicin, maduramicin, robenidine, decoquinate, halofuginone, nicarbazin and diclazuril. Main steps of the method are addition of acetonitrile to the milk samples, centrifugation, removal of matrix by SPE, concentration by evaporation and LC-MS-MS determination. During a 15 min time segmented chromatographic run compounds are ionised either positively or negatively. Calculated recoveries range between 77.1% and 118.2%. Maximum levels are in the range of 1-20 µg/kg. The developed method was validated in line with the requirements of Commission Decision 2002/657/EC (2002). It is applicable for control of coccidiostat residues in milk as indicated in Regulation 124/2009/EC (2009).

Determination of phenols and chlorophenols as trimethylsilyl derivatives using gas chromatography-mass spectrometry.

A rapid and simple method is described for the simultaneous determination of 6 phenols (phenol, o-, m-, p-cresol, catechol and resorcinol) and 19 chlorophenols (all mono-, di-, tri-, and tetrachlorophenol isomers and pentachlorophenol) present in aqueous samples. The method is based on derivatization with trimethylsilyl-N,N-dimethylcarbamate (TMSDMC). In contrast to other derivatization agents, TMSDMC instantaneously reacts with the phenolic compounds at room temperature and no further sample processing is necessary prior to instrumental analysis. The determination of the derivatives was performed by capillary gas chromatography-mass spectrometry (GC-MS). The stability of the most instable trimethylsilyl derivative (pentachlorophenol) was studied using different excess levels of the derivatization reagent. The derivatization method was tested on spiked water samples preconcentrated by solid phase extraction on Isolute ENV+ cartridge. The overall method gave detection limits of 0.01-0.25 microg/L for all compounds and < 0.05 microg/L for 17 of them.