Is dentin analogue material a viable substitute for human dentin in fatigue behavior studies?

This study aimed to compare the fatigue performance of a lithium disilicate ceramic cemented on different substrates (human dentin and glass fiber-reinforced epoxy resin - GFRER), treated with different types of conditioning (CTR - without surface conditioning; HF5 - 5% hydrofluoric acid; HF10 - 10% hydrofluoric acid; H3PO4 - phosphoric acid 37%; SAND - sandblasting with aluminum oxide). The occlusal surface of human molars (DENT group) (n = 15) was ground for dentin exposure and the root portion was cut, then the dentin slice (2.0 mm thick) was conditioned with 37% phosphoric acid and a dual-curing dental adhesive was applied. The GFRER in a round-rod format was cut into discs (Ø = 10 mm, 2.0 mm thick). Lithium disilicate glass ceramic blocks (IPS e.max CAD, Ivoclar, Schaan, Liechtenstein) were shaped into a cylinder format and cut, resulting in 90 discs (Ø = 10 mm, 1.5 mm thick). The substrate materials of each group were etched according to the groups and the ceramic was etched with 5% hydrofluoric acid for 30 s. A silane coupling agent was applied over the cementation surface in ceramic and GFRER surfaces and a dual cement was used for cementation (ceramic/GFRER or dentin). The disc/disc sets were submitted to thermocycling (25,000 cycles + storage for 6 months), and then tested in step-wise accelerated cyclic fatigue test. The failure pattern and topography were analyzed and the roughness and contact angle were measured before and after surface treatment. The DENT group presented the lowest load to failure values and number of cycles to failure in fatigue (637.33 N; 118.333), showing no statistical similarity with any of the other tested groups (p < 0.05). The topographic analysis showed that all proposed surface treatments modified the substrate surface when compared to the CTR group. All of the fractographical inspections demonstrated failure by radial crack. Considering the roughness analysis, the post-etched DENT group showed similar roughness to all groups of GFRER materials with their surface treated, except for SAND, which showed greater roughness and statistically different from the other groups. The DENT group (49.5) showed statistically different post-conditioning contact angle values from the HF10 group (96.5) and similar to the other groups. The glass fiber-reinforced epoxy resin was not able to simulate the results presented by the human dentin substrate when cemented to lithium disilicate regarding fatigue failure load and number of cycles for failure, regardless of the surface treatment. Lithium disilicate cemented on dentin analogue overestimates the load values for fatigue failure.

Cement Choice and the Fatigue Performance of Monolithic Zirconia Restorations.

This study investigated the fatigue failure load of simplified monolithic yttria partially stabilized zirconia polycrystal restorations cemented to a dentin-like substrate using different luting systems. Disc-shaped ceramic (Zenostar T, 10 mm Ø × 0.7 mm thick) and dentin-like substrate (10 mm Ø × 2.8 mm thick) were produced and randomly allocated into eight groups, without or with thermocycling (TC=5-55°C/12,000×): "cement" (RelyX Luting 2 - glass ionomer cement [Ion], [Ion/TC]; RelyX U200 - self-adhesive resin cement [Self], [Self/TC]; Single Bond Universal+RelyX Ultimate - MDP-containing adhesive + resin cement [MDPAD + RC], [MDP-AD + RC/TC]; ED Primer II+Panavia F 2.0 - Primer + MDP-containing resin cement [PR + MDP-RC], [PR + MDP-RC/TC])). Each luting system was used as recommended by the manufacturer. Staircase methodology (20 Hz; 250,000 cycles) was applied for obtaining the fatigue failure loads. Fractographic characteristics were also assessed. At baseline, the Ion group presented the lowest fatigue load, although it was statistically similar to the Self group. The resin-based cement systems presented the highest fatigue performance, with the Ion group being only statistically equal to the Self group. Thermocycling influenced the groups differently. After aging, the MDP-AD + RC presented the highest mean, followed by the PR + MDP-RC and Self groups, while the Ion group had the lowest mean. Fractographic analysis depicted all failures as radial cracks starting at the zirconia intaglio surface. The luting system with MDP-containing adhesive applied prior to the resin cement presented the highest fatigue failure load after aging, presenting the best predictability of stable performance. Despite this, monolithic zirconia presents high load-bearing capability regardless of the luting agent.

Adhesion to a Zirconia-reinforced Lithium Silicate Ceramic: Effects of Ceramic Surface Treatments and Resin Cements.

OBJECTIVE: This study had the objective to test the effect of ceramic surface treatments on the microshear bond strength (µSBS) of different resin cements to a zirconia-reinforced lithium silicate (ZLS). METHODS AND MATERIALS: ZLS blocks were sectioned, embedded in acrylic resin, and then allocated into nine groups considering two study factors: "ceramic surface treatment" (HF - hydrofluoric acid; EP - self-etching primer; TBS - tribochemical silica coating) and "resin cements" (nMDP - without MDP monomer; MDP - with MDP monomer; SA - self-adhesive). Starch tubes (n=36) were placed on the treated ceramic surface and the cement was applied. Starch tubes were removed after 24 hours of storage, and the specimens were thermocycled (5,000×; 5°C-55°C). Next, the µSBS test was performed using the wire-loop technique, and topographic and failure analyses were performed. RESULTS: The factors "ceramic surface treatment" and "resin cement" statistically influenced the µSBS results. Considering the surface treatment factor, the TBS produced statistically lower values when the MDP resin cement was applied, being only similar to the MDP plus EP group. For the resin cement factor, no difference was found for nMDP and SA groups, apart from the surface treatments. Failure analysis showed that the groups treated with EP had a greater number of pre-test failures. The surface treatments induced noteworthy topographic alterations when compared to control (no treatment). CONCLUSION: The ZLS ceramic surface treatment with tribochemical silica coating associated with the MDP-containing resin cement resulted in lower bond strength values.

Fatigue Behavior of Monolithic Zirconia-Reinforced Lithium Silicate Ceramic Restorations: Effects of Conditionings of the Intaglio Surface and the Resin Cements.

OBJECTIVE: This study assessed the effect of conditioning of the intaglio surface and resin cements on the fatigue behavior of zirconia-reinforced lithium silicate ceramic (ZLS) restorations cemented to a dentin analogue. METHODS: ZLS ceramic (Ø=10 mm, thickness=1.5 mm) and dentin analogue (Ø=10 mm, thickness=2.0 mm) discs were produced and allocated according to the study factors, totaling nine study groups: ceramic surface treatment (three levels: hydrofluoric acid etching [HF]; self-etching ceramic primer [EP]; tribochemical silica coating [TBS]) and resin cement (three levels: 10-methacryloyloxydecyl dihydrogen phosphate [nMDP]; MDP-containing conventional resin cement [MDP]; self-adhesive resin cement [SA]). The ceramic bonding surfaces were treated and cemented on the dentin analogue, and all the specimens were aged for 5000 thermal cycles (5°C-55°C) prior to fatigue testing. The stepwise fatigue test (20 Hz frequency) started with a load of 400 N (5000 cycles) followed by steps of 500, 600, and up to 1800 N (step-size: 100 N) at a maximum of 10,000 cycles each step. The specimens were loaded until failure (crack), which was detected by light transillumination and visual inspection at the end of each step. The fatigue failure load and number of cycles for failure data were analyzed by the Kaplan-Meier (log-rank test; α=0.05). Topographic and fractographic analyses were also performed. RESULTS: HF- (973.33-1206.67 N) and EP- (866.67-1066.67 N) treated specimens failed at statistically similar loads and higher than TBS (546.67-733.33 N), regardless of the cement used. All the fractographical inspections demonstrated failure as radial crack. CONCLUSION: The HF and EP treatments promoted better mechanical fatigue behavior of the ceramic restoration, while tribochemical silica coating induced worse fatigue results and should be avoided for treating the ZLS surface prior to bonding.

Fatigue Failure Load of a Bonded Simplified Monolithic Feldspathic Ceramic: Influence of Hydrofluoric Acid Etching and Thermocycling.

OBJECTIVE: To evaluate the effect of hydrofluoric acid (HF) etching and thermocycling (Tc) on fatigue failure load of feldspathic ceramic restorations cemented with two resin cements. METHODS: Disc-shaped feldspathic ceramic (Vitablocs Mark II; Ø=10 mm, 1.0-mm thick) and G10 epoxy resin (Ø=10 mm, 2.5-mm thick) specimens were made and randomly allocated considering three factors: ceramic etching (ie, with vs without 10% HF plus silane application), resin cement (ie, self-adhesive [RelyX U200; U200] or conventional [Multilink Automix; MA]), and Tc (ie, with vs without 5-55°C/12,000 cycles). Adhesive cementation followed each manufacturer's instructions. The fatigue test (n=20) was based on the staircase approach (250,000 cycles; 20 Hz). Contact angle, surface topography, and fractography analysis were also executed. Specific statistical tests were employed for each outcome (α=0.05). RESULTS: The interaction of HF and Tc factors decreased the fatigue resistance for both cements (U200 542.63>U200/HF-Tc 495.00; MA 544.47>MA/HF-Tc 506.84). Comparing the cements associated with HF or Tc, there was statistical superiority for MA (U200-Tc 537.37

Effect of Resin Luting Systems and Alumina Particle Air Abrasion on Bond Strength to Zirconia.

This study aimed to evaluate the effect of different primer/resin luting agent combinations and alumina air abrasion on the adhesion to zirconia. Eighty blocks (4×4×3 mm) of Lava Frame Zirconia (3M ESPE) were produced and randomly assigned into eight groups (n=10) according to two zirconia surface treatments (untreated or air abrasion with 50-µm alumina particles) and four luting systems (SU: Scotchbond Universal/RelyX Unicem 2; ZP: Z-Prime Plus/Duo-link Universal; MB: Monobond Plus/Variolink II; and AP: Alloy Primer/ED Primer II/Panavia F 2.0). After the conditioning and primer applications, resin luting agents were manipulated and applied on the zirconia, using a matrix, to form a cylinder (2 mm in diameter×2 mm high), followed by photoactivation for 40 seconds. After that, the specimens were stored in distilled water (37 °C) for 120 days and then submitted to shear bond strength testing, followed by failure mode evaluation under an optical microscope (30×). A two-way analysis of variance and Tukey test (α=0.05) were used for data analysis. Alumina air abrasion (Al) promoted higher bond values for the three luting systems, except for SU, which showed the best results without air abrasion, while with air abrasion, Al-SU, Al-ZP, and Al-MB presented higher values compared to Al-AP. We concluded that the alumina air abrasion of zirconia surfaces seemed to be dispensable for the SU group, while air abrasion (topographical alterations) enhanced the adhesion of the ZP, MB, and AP groups.

Fatigue Failure Load of Restored Premolars: Effect of Etching the Intaglio Surface of Ceramic Inlays With Hydrofluoric Acid at Different Concentrations.

The aim of this study was to evaluate the effect of etching, with different hydrofluoric acid concentrations at the intaglio surface of feldspathic ceramic inlays, on the fatigue failure load of restored premolars. A total of 60 upper premolars were embedded in plastic cylinders with acrylic resin (up to 3 mm below the cement-enamel junction) and prepared using a device specially designed for that purpose. Teeth were randomly assigned to three groups (n=20): HF1, HF5, and HF10 (etching with hydrofluoric acid for 60 seconds at concentrations of 1%, 5%, and 10%, respectively). Preparations were scanned and restorations were milled by a computer-aided design / computer-aided manufacturing system. The inner surfaces of the inlays were etched and received an application of a silane coupling agent; the dentin and enamel were treated appropriately for the luting system (RelyX ARC, 3M-ESPE). The restorations were cemented and the fatigue failure load (in N) was determined using the staircase method (10 Hz; 105 cycles in each step). The initial load (585.5 N) was applied on the slopes of the cusps (labial and palatal/lingual, simultaneously) through a cylinder attached to the test machine (Instron ElectroPuls E3000). The tested samples were analyzed under a stereomicroscope for failure analysis. Fatigue data were analyzed by one-way analysis of variance. There was no statistical difference among the fatigue failure loads (in N): HF1 (448.5±79.1), HF5 (360.7±55.4), and HF10 (409.5±121.1). Regarding the fracture mode, there was a predominance of interfacial fracture (50%), followed by cusp fracture (34.6%). It may be concluded that the etching with hydrofluoric acid at the tested concentrations (1%, 5%, and 10%) does not influence the fatigue failure load of feldspathic ceramic inlays cemented on premolars.

Retentive Strength of Y-TZP Crowns: Comparison of Different Silica Coating Methods on the Intaglio Surfaces.

OBJECTIVE: To evaluate the effect of different methods of silica deposition on the intaglio surface of yttrium oxide stabilized zirconia polycrystal (Y-TZP) crowns on the retentive strength of the crowns. METHODS: One hundred simplified full-crown preparations produced from fiber-reinforced polymer material were scanned, and 100 Y-TZP crowns with occlusal retentions were milled. Crown/preparation assemblies were randomly allocated into five groups (n=20) according to the treatment of the intaglio surfaces: TBS = tribochemical silica coating via air-abrasion with 30-µm silica-coated alumina particles; GHF1 = application of thin glaze layer + hydrofluoric acid (HF) etching for 1 minute; GHF5 = glaze application + HF for 5 minutes; GHF15 = glaze application + HF for 15 minutes; NANO = silica nanofilm deposition (5 nm) via magnetron sputtering. All groups received a silane application. The surfaces of the preparations (polymer) were conditioned with 10% HF for 30 seconds and silanized. The crowns were cemented with resin cement, thermocycled (12,000 cycles; 5°C/55°C), stored for 60 days, and subjected to a retentive strength test (0.5 mm/min until failure). The retention data (MPa) were analyzed using one-way analysis of variance, Tukey tests, and Weibull analysis. Failures were classified as 50C (above 50% of cement in the crown) and 50S (above 50% of cement on the substrate). RESULTS: The TBS (5.6±1.7 MPa) and NANO groups (5.5±1 MPa) had higher retentive strength than the other groups (p<0.0001) and had the highest values of characteristic strength. There was no difference in Weibull modulus, except for the GHF1 group (lower values). The TBS and GHF15 groups, respectively, had 60% and 70% of their failures classified as 50C, while most of the other groups had 50S failures. CONCLUSION: Tribochemical silica coating and silica nanofilm deposition on the inner surface of zirconia crowns promoted a higher retentive strength.

Different Methods for Inlay Production: Effect on Internal and Marginal Adaptation, Adjustment Time, and Contact Point.

The aim of this study was to evaluate the effect of different production methods of resin and ceramic inlays on marginal and internal adaptation, adjustment time, and proximal contacts. Forty premolars were selected, embedded (their roots), and prepared to receive inlays that were made as follows (n=10): LaRe-digital impression with a Lava C.O.S. scanner, followed by milling of Lava Ultimate block (composite resin) in a milling center; CeRe-digital impression with a Cerec 3D Bluecam scanner, followed by milling of Lava Ultimate block in Cerec; CeDis-digital impression with a Cerec 3D Bluecam scanner, followed by milling of IPS e.max CAD block (lithium disilicate) in Cerec; and PresDis-impression with polyvinyl siloxane, inlay made using the lost wax technique and IPS e.max Press pressed ceramic (lithium disilicate). Marginal and internal adaptations were measured using the replica technique. The inlay adjustments were performed using diamond burs in a contra-angle hand piece, and the time for adjustment was recorded using a timer, in seconds. The tightness of the proximal contact was measured using standardized metal blades. The statistical analyses for marginal fit data showed that at the cervical edge, CeDis (177.8 µm) had greater misfit than CeRe (116.7 µm), while all the groups had similar adaptation at the occlusal edge. The groups had similar internal fit at the pulpal wall, while LaRe (104.7 µm) > CeDis (66.7 µm) = CeRe (76.7 µm) at the axial wall. The groups restored with lithium disilicate ceramic took more time for adjustment when compared to the resin restorative material. The lowest proximal contact, in micrometers, was seen in the CeRe group (8.8 µm).

Surface micro-morphology, phase transformation, and mechanical reliability of ground and aged monolithic zirconia ceramic.

This study aimed to determine the effects of grinding and low temperature aging on the biaxial flexural strength, structural reliability (Weibull analysis), surface topography, roughness analysis, and phase transformation (t→m) of an yttrium-stabilized tetragonal zirconia polycrystalline ceramic. Ceramic discs (15.0×1.2±0.2mm, VITA In-Ceram YZ) were prepared and randomly assigned into six groups according to 2 factors (n=30): 'grinding' (Ctrl - without treatment, as-sintered; Xfine - grinding with extra fine diamond bur - 30µm; Coarse - grinding by coarse diamond bur - 151µm), and 'aging' (without or with aging: CtrlLTD; XfineLTD; CoarseLTD). Grinding was performed in an oscillatory motion with a contra-angle handpiece under constant water-cooling. Low temperature degradation (LTD) was simulated in an autoclave at 134°C, under 2bar pressure, for 20h. The roughness (Ra and Rz parameters) significantly increased after grinding in accordance with bur grit-size (Coarse>Xfine>Ctrl), and aging promoted distinct effects (Ctrl=CtrlLTD; Xfine>XfineLTD; Coarse=CoarseLTD). Grinding increased the m-phase, and aging led to an increase in the m-phase in all groups. However, different susceptibilities to LTD were observed. Weibull analysis showed a significant increase in the characteristic strength after grinding (Coarse=Xfine>Ctrl), while aging did not lead to any deleterious impact. Neither grinding nor aging resulted in any deleterious impact on material reliability (no statistical decrease in the Weibull moduli). Thus, neither grinding nor aging led to a deleterious effect on the mechanical properties of the evaluated Y-TZP ceramic although a high m-phase content and roughness were observed.

Mechanical behavior of a Y-TZP ceramic for monolithic restorations: effect of grinding and low-temperature aging.

This study aimed to investigate the effects of grinding with diamond burs and low-temperature aging on the mechanical behavior (biaxial flexural strength and structural reliability), surface topography, and phase transformation of a Y-TZP ceramic for monolithic dental restorations. Disc-shaped specimens (Zirlux FC, Ivoclar Vivadent) were manufactured according to ISO 6872 (2008) and divided in accordance with two factors: "grinding - 3 levels" and "LTD - 2 levels". Grinding was performed using a contra-angle handpiece under constant water-cooling with different grit-sizes (extra-fine and coarse diamond burs). LTD was simulated in an autoclave at 134°C, under a pressure of 2 bar, over a period of 20h. Surface topography analysis showed an increase in roughness based on surface treatment grit-size (Coarse>Xfine>Ctrl), LTD did not influence roughness values. Both grinding and LTD promoted an increase in the amount of m-phase, although different susceptibilities to degradation were observed. According to existing literature the increase of m-phase content is a direct indicative of Y-TZP degradation. Weibull analysis showed an increase in characteristic strength after grinding (Coarse=Xfine>Ctrl), while for LTD, distinct effects were observed (Ctrl

Comparison of different low-temperature aging protocols: its effects on the mechanical behavior of Y-TZP ceramics.

This study evaluated the effect of different protocols of low-temperature degradation simulation on the mechanical behavior (structural reliability and flexural strength), the surface topography (roughness), and phase transformation of a Y-TZP ceramic. Disc-shaped specimens (1.2mm×12mm, Lava Frame, 3M ESPE, Seefeld, Germany) were manufactured according to ISO:6872-2008 and divided (n=30) according to the aging protocol executed: "Ctrl" - as-sintered - without any treatment; "Dist Water" - stored at distilled water at 37°C for 365 days; "MC" mechanical cycling into two steps: First - 200N, 2.2Hz for 2.000.000 cycles, Second - 450N, 10Hz for 1.000.000 cycles; "Aut" - steam autoclave at 134°C, 2bar (200kPa) for 20h; "Aut+MC"- Aut and MC methods. Roughness analysis (µm) showed, for Ra parameter, higher statistically significant values for Ctrl 0.68 (0.27), while for Rz parameter, the highest values were observed for Ctrl 4.43(1.53) and Aut 2.24 (0.62). Surface topography analysis showed that none aging method promoted surface alterations when compared to control group. Phase transformation analysis showed that all aging methods promoted an increase in m-phase content (Ctrl: 0.94%, Dist Water: 20.73%, MC: 9.47%, Aut: 53.33% and Aut+MC: 61.91%). Weibull Analysis showed higher statistical characteristic strength values for Aut (1033.36MPa) and Dist Water (1053.76MPa). No aging method promoted deleterious impact either on the biaxial flexural strengths or on the structural reliabilities (Weibull moduli). Also, none of the aging methods promoted reduction of Y-TZP mechanical properties; thus the development of new methodologies and the association between mechanical stimuli and hydrothermal degradation should be considered to better understand the mechanism of low-temperature degradation.

Fatigue limit of polycrystalline zirconium oxide ceramics: Effect of grinding and low-temperature aging.

The following study aimed to evaluate the effect of grinding and low-temperature aging on the fatigue limit of Y-TZP ceramics for frameworks and monolithic restorations. Disc specimens from each ceramic material, Lava Frame (3M ESPE) and Zirlux FC (Ivoclar Vivadent) were manufactured according to ISO:6872-2008 and assigned in accordance with two factors: (1) "surface treatment"-without treatment (as-sintered, Ctrl), grinding with coarse diamond bur (181µm; Grinding); and (2) "low-temperature aging (LTD)" - presence and absence. Grinding was performed using a contra-angle handpiece under constant water-cooling. LTD was simulated in an autoclave at 134°C under 2-bar pressure for 20h. Mean flexural fatigue limits (20,000 cycles) were determined under sinusoidal loading using stair case approach. For Lava ceramic, it was observed a statistical increase after grinding procedure and different behavior after LTD stimuli (Ctrl

Resin Bonding to a Hybrid Ceramic: Effects of Surface Treatments and Aging.

The aim of this study was to verify the effects of different surface treatments on the microtensile bond strength between resin cement and a hybrid ceramic. Thirty-two hybrid ceramic slices (8 × 10 × 3 mm) were produced and allocated among four groups according to the surface treatment: Cont = no treatment, HA = 10% hydrofluoric acid applied for 60 seconds, PA = 37% phosphoric acid applied for 60 seconds and CJ = air abrasion with silica particle coated alumina (Cojet Sand, 3M ESPE, 30 µm/2.8 bar). As a control group, eight blocks of feldspathic ceramic (8 × 10 × 3 mm) were etched by hydrofluoric acid for 60 seconds (VMII). After the surface treatments, the ceramic slices were silanized (except the Cont group) and adhesively cemented to composite resin blocks (8 × 10 × 3 mm ) with a load of 750 g (polymerized for 40 seconds each side). The cemented blocks were cut into beams (bonded surface area of ∼1 mm(2)). Half of the beams were aged (thermocycling of 5°C-55°C/6000 cycles + water storage at 37°C/60 days), and the other half were tested immediately after being cut. Data were analyzed by Kruskal-Wallis and Dunn tests (non-aged groups) and by one-way analysis of variance and Tukey test (aged groups; α=0.05%). The mode of failure was classified by stereomicroscopy. The surface treatment significantly affected the bond strength in each set of groups: non-aged (p=0.001) and aged (p=0.001). Before being aged, samples in the CJ, HA, and PA groups achieved the highest bond strength values. However, after being aged, only those in the HA group remained with the highest bond strength values. Adhesive failure was found most often. In conclusion, hydrofluoric acid etching should be used for surface conditioning of the studied hybrid ceramic.

Are posts necessary for the restoration of root filled teeth with limited tissue loss? A structured review of laboratory and clinical studies.

Guidelines for post placement are lacking in respect of the amount of tooth structure, particularly in cases in which ≥50% of coronal structure is preserved. The aim of this review was to provide evidence-based principles for the use of posts in the restoration of root filled teeth with limited tissue loss. A literature search of laboratory and clinical studies published between 2000 and 2014 was conducted in PubMed. Included studies contained at least one study group with root filled teeth restored without a post, presented at least one group with root filled teeth with limited tissue loss, and, in the case of laboratory studies, performed mechanical cycling prior to a fracture resistance test. Based on the evidence from laboratory studies, root filled premolars and molars with limited tissue loss can be restored without posts, particularly when total coverage is planned. However, when no cusp protection is provided, post placement appears to be beneficial in premolars. Evidence regarding the best restoration option for root filled incisors with limited tissue loss remains controversial. When total coverage is intended, reconstruction seems to be successfully performed by restoration with composite. However, some reports consider that post insertion increases fracture loads. The review of clinical studies demonstrated that survival of teeth with substantial tooth tissue is not influenced by the use of posts. Exceptions were found when only premolars were investigated; in these cases, post placement was associated with greater survival rates in crowned teeth and fewer root fractures in teeth without cusp protection.

Evaluation of tensile retention of Y-TZP crowns cemented on resin composite cores: effect of the cement and Y-TZP surface conditioning.

This study evaluated the effect of the cement type (adhesive resin, self-adhesive, glass ionomer, and zinc phosphate) on the retention of crowns made of yttria-stabilized polycrystalline tetragonal zirconia (Y-TZP). Therefore, 108 freshly extracted molars were embedded in acrylic resin, perpendicular to their long axis, and prepared for full crowns: the crown preparations were removed and reconstructed using composite resin plus fiber posts with dimensions identical to the prepared dentin. The preparations were impressed using addition silicone, and Y-TZP copings were produced, which presented a special setup for the tensile testing. Cementation was performed with two adhesive resin cements (Multilink Automix, Ivoclar-Vivadent; RelyX ARC, 3M ESPE, St Paul, MN, USA), one self-adhesive resin cement (RelyX U100, 3M ESPE), one glass ionomer based cement (RelyX Luting, 3M ESPE), and one zinc phosphate cement (Cimento de Zinco, SS White, Rio de Janeiro, Brazil). For the resin cement groups, the inner surfaces of the crowns were subjected to three surface treatments: cleaning with isopropyl alcohol, tribochemical silica coating, or application of a thin low-fusing glass porcelain layer plus silanization. After 24 hours, all groups were subjected to thermocycling (6000 cycles) and included in a special device for tensile testing in a universal testing machine to test the retention of the infrastructure. After testing, the failure modes of all samples were analyzed under a stereomicroscope. The Kruskal-Wallis test showed that the surface treatment and cement type (α=0.05) affected the tensile retention results. The Multilink cement presented the highest tensile retention values, but that result was not statistically different from RelyX ARC. The surface treatment was statistically relevant only for the Multilink cement. The cement choice was shown to be more important than the crown surface treatment for cementation of a Y-TZP crown to a composite resin substrate.

Inlays made from a hybrid material: adaptation and bond strengths.

The aim of this study was to evaluate the internal fit, marginal adaptation, and bond strengths of inlays made of computer-aided design/computer-aided manufacturing feldspathic ceramic and polymer-infiltrated ceramic. Twenty molars were randomly selected and prepared to receive inlays that were milled from both materials. Before cementation, internal fit was achieved using the replica technique by molding the internal surface with addition silicone and measuring the cement thicknesses of the pulpal and axial walls. Marginal adaptation was measured on the occlusal and proximal margins of the replica. The inlays were then cemented using resin cement (Panavia F2.0) and subjected to two million thermomechanical cycles in water (200 N load and 3.8-Hz frequency). The restored teeth were then cut into beams, using a lathe, for microtensile testing. The contact angles, marginal integrity, and surface patterns after etching were also observed. Statistical analysis was performed using two-way repeated measures analysis of variance (p<0.05), the Tukey test for internal fit and marginal adaptation, and the Student t-test for bond strength. The failure types (adhesive or cohesive) were classified on each fractured beam. The results showed that the misfit of the pulpal walls (p=0.0002) and the marginal adaptation (p=0.0001) of the feldspathic ceramic were significantly higher when compared to those of the polymer-infiltrated ceramic, while the bond strength values of the former were higher when compared to those of the latter. The contact angle of the polymer-infiltrated ceramic was also higher. In the present study, the hybrid ceramic presented improved internal and marginal adaptation, but the bond strengths were higher for the feldspathic ceramic.

Evaluation of tensile retention of Y-TZP crowns after long-term aging: effect of the core substrate and crown surface conditioning.

This study evaluated the effect of the core substrate type (dentin and composite resin) on the retention of crowns made of yttrium oxide stabilized tetragonal zirconia polycrystal (Y-TZP), submitted to three inner surface conditionings. For this purpose, 72 freshly extracted molars were embedded in acrylic resin, perpendicular to the long axis, and prepared for full crowns: 36 specimens had crown preparations in dentin; the remaining 36 teeth had the crowns removed, and crown preparations were reconstructed with composite resin plus fiber posts with dimensions identical to the prepared dentin. The preparations were impressed using addition silicone, and 72 Y-TZP copings for the tensile test were produced. Cementation was performed with a dual-cured cement containing phosphate monomers. For cementation, the crown preparation (dentin or resin) was conditioned with the adhesive system, and the ceramic was subjected to one of three surface treatments: isopropyl alcohol, tribochemical silica coating, or thin low-fusing glassy porcelain layer application plus silanization. After 24 hours, all specimens were submitted to thermocycling (6000 cycles) and placed in a special tensile testing device in a universal testing machine to determine failure loads. The failure modes of all samples were analyzed under a stereomicroscope. Two-way analysis of variance showed that the surface treatment and substrate type (α=0.05) affected the tensile retention results. The dentin substrate presented the highest tensile retention values, regardless of the surface treatment. When the substrate was resin, the tribochemical silica coating and low-fusing glaze application plus silanization groups showed the higher retention values.

Adhesion between fiber post and root dentin: evaluation of post surface conditioning for bond strength improvement.

AIM: The aim of this paper was to evaluate two surface conditioning methods associated with the application of adhesive on the post surface for improving the bond to resin cement. METHODS: Sixty single-rooted bovine teeth were sectioned at 16 mm in length, prepared (9 mm depth), embedded in a PVC cylinder using acrylic resin, and allocated into 3 groups (N.=20) according to post surface treatment: cleaning with ethanol (control group); etching with hydrogen peroxide; etching with hydrofluoric acid. Ten posts for each group were silanized and other 10 posts were silanized and received an adhesive agent. The posts were cemented with self-adhesive resin cement (RelyX U100 resin cement). All teeth were sectioned perpendicularly to the long axis (2 mm thickness per slice), submitted to push out bond strength testing and the type of failure was recorded. The obtained data were submitted to two-way ANOVA and Turkey´s test, with the level of significance set at 5%. RESULTS: Neither the hydrofluoric acid or hydrogen peroxide post surface treatment, nor the adhesive application, had an influence on bond strength values. The main type of failure was adhesive between cement and dentin. CONCLUSION: Etching and the application of an adhesive on the post surface did not presented a significant influence on the bond strength results for the fiber post resin cement-root dentin assembly. The cement appears to adhere very well to the fiber post surface rather than the dentin surface.

Anetoderma in a systemic lupus erythematosus patient with anti-PCNA and antiphospholipid antibodies.

Anetoderma is a rare elastolytic disorder included within the group of cutaneous atrophies. Its pathogenesis is not yet clearly established, but immunological mechanisms could play an important role in dermal elastolysis. It has been associated with different autoantibodies and autoimmune disorders. We present a case of anetoderma in a systemic lupus erythematosus patient with anti-proliferating-cell-nuclear-antigen and antiphospholipid antibodies, highlighting the peculiarities of such an association.