Evaluation of Oleogels Stabilized by Particles of Birch Outer Bark Extract through a Novel Approach.

Structuring liquid oils into oleogels using natural and abundant biomass components as gelling agents is of great significance in fields such as foods, pharmaceuticals, and cosmetics. In this work, a more energy-efficient and technologically simpler approach for directly preparing birch outer bark extract particles containing oleogel was used. This method involves introducing birch outer bark extract particles into the oil phase directly from the extract solution, combining both the evaporation of solution and gel formation. As a result, stable oleogels of various vegetable oils (sunflower, almond, olive, and hemp seed) were obtained with birch outer bark extract particle contents of 4-10%. Infrared spectroscopy and particle size analysis confirmed that when increasing the content of extract particles in the oil, increasing self-assembly of extract particles via hydrogen bonding occurs, leading to the formation of a more structured network. This is consistent with gel strength values from rheological tests of oleogels, which also increased with particle concentration. The obtained oleogels showed important properties such as good tolerance to time-dependent deformation, shear thinning, and thermoreversibility.

Effect of Betulin Colloidal Particles on Proliferation and Cytokine Secretion of Human Skin Fibroblasts.

The aim of the study was to obtain untreated and treated betulin colloidal particles and assess their effect on the viability, morphology, proliferation and cytokine secretion of human dermal fibroblasts. To improve bioavailability, betulin treatment was performed by an antisolvent precipitation technique. The average particle size after treatment in the aqueous dispersion decreased from 552.9 ± 11.3 to 278.2 ± 1.6 nm. Treated betulin colloidal particles showed no cytotoxicity up to a concentration of 400 µg·mL-1 in the colorimetric tetrazolium salt viability test (CCK-8). Moreover, the cell morphology was not changed in the presence of betulin colloidal particles at a concentration range from 0.78 to 400 µg·mL-1. The obtained results also show that betulin particles induce the secretion of the proinflammatory and angiogenesis-stimulating cytokine IL-8. However, further studies would be required to clarify the mechanism of IL-8 secretion induction.

Analytical Method Cluster Development for Comprehensive Characterisation of Suberinic Acids Derived from Birch Outer Bark.

Suberin is a complex polyester biopolymer, and it is practically impossible to estimate the real content of suberin in suberised plant tissues. This indicates the importance of the development of instrumental analytical methods for the comprehensive characterisation of suberin derived from plant biomass for the successful integration of suberinic products into biorefinery production chains. In this study, we optimised two GC-MS methods-one with direct sylilation, and the second with additional depolymerisation, using GPC methods with RI detector and polystyrene calibration and with a three-angle light scattering detector and an eighteen-angle light scattering detector. We also performed MALDI-Tof analysis for non-degraded suberin structure determination. We characterised suberinic acid (SA) samples obtained from birch outer bark after alkaline depolymerisation. The samples were particularly rich in diols, fatty acids and their esters, hydroxyacids and their corresponding esters, diacids and their corresponding esters, as well as extracts (mainly betulin and lupeol) and carbohydrates. To remove phenolic-type admixtures, treatment with ferric chloride (FeCl3) was used. The SA treatment with FeCl3 allows the possibility to obtain a sample that has a lower content of phenolic-type compounds and a lower molecular weight than an untreated sample. It was possible to identify the main free monomeric units of SA samples by GC-MS system using direct silylation. By performing an additional depolymerisation step before silylation, it was possible to characterise the complete potential monomeric unit composition in the suberin sample. For the molar mass distribution determination, it is important to perform GPC analysis. Even though chromatographic results can be obtained using a three- laser MALS detector, they are not fully correct because of the fluorescence of the SA samples. Therefore an 18-angle MALS detector with filters was more suitable for SA analysis. MALDI-Tof analysis is a great tool for the polymeric compound structural identification, which cannot be done using GC-MS. Using the MALDI data, we discovered that the main monomeric units that makes up the SA macromolecular structure are octadecanedioic acid and 2-(1,3-dihydroxyprop-2-oxy)decanedioic acid. This corresponds with GC-MS results, showing that after depolymerisation hydroxyacids and diacids were the dominant type of compounds found in the sample.

Qualitative Differences and Emission Persistence of Volatile Organic Compounds from Bio-Based Particleboards.

An attempt to reduce, replace, or even eliminate the synthetic resins from wood-based panels alongside broadening the array of raw lignocellulosics is still essential and attractive. Many pretreatments of lignocellulosics have been studied, among which steam explosion (SE) resulted in superior physical-mechanical properties of the obtained binder-less boards. However, the SE pretreatment leads to a relatively strong odor, which is even emitted from the obtained binder-less boards independent of the raw lignocellulosic, raising concern about the use of the boards. Emissions of volatile organic compounds (VOCs) were investigated in the framework of the study from binder-less boards obtained from different SE raw lignocellulosics and SE-untreated suberinic acids-bonded particleboard. VOCs were collected by headspace solid-phase microextraction (HS-SPME) and analyzed by gas chromatography-mass spectrometry (GC-MS) for 28 days with an interval of 2 weeks. The results showed that the number of detected VOCs and their chromatographic peak area varied significantly depending on the raw lignocellulosic, board density, and post-treatment (overlayering), decreasing over time. The lowest area of detected VOCs was demonstrated by the suberinic acids-bonded particleboard, while the highest area was detected from the high-density binder-less board obtained from SE hemp shives with the main compound of furfural (up to 70%) in all board types.

Influence of Manufacturing Conditions on Binder-Less Boards from Steam-Exploded Hemp Shives and Wheat Straw.

In the current decade, based on the European Green Deal, new challenges of the wood-based panel industry have arisen, seeking for formaldehyde-free bio-based adhesives and broadening raw lignocellulosics. In order to contribute to the potential solution to the challenges, binder-less boards of steam-exploded (SE 220 °C/2 min) hemp shives and wheat straw were investigated. The objective of this study was to find out the optimal hot-pressing conditions in terms of temperature (150-200 °C) and time (5-16 min) for the boards with three density levels (800-1000-1200 kg·m-3). An experimental design was created and the influence of the variables on binder-less panels were evaluated using a randomized central composite design of the response surface methodology. Water absorption (WA) and thickness swelling (TS) during 24 h, modulus of elasticity (MOE), and modulus of rupture (MOR) in bending test, internal bonding (IB), and Fourier-transform infrared spectroscopy were determined for the obtained boards. Each detected physical-mechanical property of the obtained boards was described by statistical models being different at each density level. The optimal conditions of the obtained binder-less boards were different depending on the raw material and density. For example, the optimal conditions of the boards from SE wheat straw with a density of 800 kg m-3 were found at T = 220 °C and t = 15 min, with the achieved properties of WA = 53%, TS = 4%, MOE = 2750 N mm-2, MOR = 15.5 N mm-2, and IB = 0.64 N mm-2. Based on the achieved properties at the optimal conditions, the boards meet the requirements of the conventional particleboard Type P3 according to EN 312.