Yield stress-enabled microencapsulation of field responsive microparticle suspensions.

Try and encapsulate microparticles inside the cores of microcapsules and you will often find that particles adhere to the liquid-liquid interface in a phenomenon known as Pickering stabilization. Particles will remain irreversibly trapped and embedded within the subsequently formed microcapsule membrane. In cases where the encapsulant particles must remain suspended inside the microcapsule core to retain their desired properties or behaviours, Pickering stabilization is detrimental. Here we demonstrate a general procedure using yield stress materials as the core material, where the yield stress of the gel is strong enough to suspend particles against sedimentation, but weak enough to allow spatial manipulation of encapsulant particles using an external field. This external field imparts enough force on particles to disrupt the supporting network and allow particle mobility after encapsulation.

Microrollers flow uphill as granular media.

Pour sand into a container and only the grains near the top surface move. The collective motion associated with the translational and rotational energy of the grains in a thin flowing layer is quickly dissipated as friction through multibody interactions. Alternatively, consider what will happen to a bed of particles if one applies a torque to each individual particle. In this paper, we demonstrate an experimental system where torque is applied at the constituent level through a rotating magnetic field in a dense bed of microrollers. The net result is the grains roll uphill, forming a heap with a negative angle of repose. Two different regimes have been identified related to the degree of mobility or fluidisation of the particles in the bulk. Velocimetry of the near surface flowing layer reveals the collective motion of these responsive particles scales in a similar way to flowing bulk granular flows. A simple granular model that includes cohesion accurately predicts the apparent negative coefficient of friction. In contrast to the response of active or responsive particles that mimic thermodynamic principles, this system results in macroscopic collective behavior that has the kinematics of a purely dissipative granular system.

Three-Dimensional Sag Tracking in Falling Liquid Films.

Coating defects often arise during application in the flash stage, which constitutes the ∼10 min interval immediately following film application when the solvent evaporates. Understanding the transient rheology and kinematics of a coating system is necessary to avoid defects such as sag, which results in undesirable appearance. A new technique named variable angle inspection microscopy (VAIM) aimed at measuring these phenomena was developed and is summarized herein. The essence of this new, non-invasive, rheological technique is the measurement of a flow field in response to a known gravitational stress. VAIM was used to measure the flow profile through a volume of a liquid thin film at an arbitrary orientation. Flow kinematics of the falling thin film was inferred from particle tracking measurements. Initial benchmarking measurements in the absence of drying tracked the velocity of silica probe particles in ∼140 µm thick films of known viscosity, much greater than water, at incline angles of 5° and 10°. Probe particles were tracked through the entire thickness of the film and at speeds as high as ∼100 µm/s. The sag flow field was well resolved in ∼10 µm thick cross sections, and in general the VAIM measurements were highly reproducible. Complementary profilometer measurements of film thinning were utilized to predict sag velocities with a known model. The model predictions showed good agreement with measurements, which validated the effectiveness of this new method in relating material properties and flow kinematics.

Pattern Engineering of Living Bacterial Colonies Using Meniscus-Driven Fluidic Channels.

Creating adaptive, sustainable, and dynamic biomaterials is a forthcoming mission of synthetic biology. Engineering spatially organized bacterial communities has a potential to develop such bio-metamaterials. However, generating living patterns with precision, robustness, and a low technical barrier remains as a challenge. Here we present an easily implementable technique for patterning live bacterial populations using a controlled meniscus-driven fluidics system, named as MeniFluidics. We demonstrate multiscale patterning of biofilm colonies and swarms with submillimeter resolution. Utilizing the faster bacterial spreading in liquid channels, MeniFluidics allows controlled bacterial colonies both in space and time to organize fluorescently labeled Bacillus subtilis strains into a converged pattern and to form dynamic vortex patterns in confined bacterial swarms. The robustness, accuracy, and low technical barrier of MeniFluidics offer a tool for advancing and inventing new living materials that can be combined with genetically engineered systems, and adding to fundamental research into ecological, evolutional, and physical interactions between microbes.