The impact on passenger car emissions associated with the promotion and demise of diesel fuel.

The promotion and growth in the use of diesel fuel in passenger cars in the UK and Europe over the past two decades led to considerable adverse air quality impacts in urban areas and more widely. In this work, we construct a multi-decade analysis of passenger car emissions in the UK based on real driving emissions data. An important part of the study is the use of extensive vehicle emission remote sensing data covering multiple measurement locations, time periods, environmental conditions and consisting of over 600,000 measurements. These data are used to consider two scenarios: first, that diesel fuel use was not promoted in the early 2000s for climate mitigation reasons, and second, that there was not a dramatic decline in diesel fuel use following the Dieselgate scandal. The strong growth of diesel fuel use coincided with a time when diesel NOx emissions were high and, conversely, the strong decrease of diesel fuel use coincided with a time when diesel vehicle after-treatment systems for NOx control were effective. We estimate that the growth in diesel car use in the UK results in excess NOx emissions of 721 kt over a three decade period; equivalent to over 7 times total annual passenger car NOx emissions and greater than total UK NOx emissions of 681.8 kt in 2021 and with an associated damage cost of £5.875 billion. However, the sharp move away from diesel fuel post-Dieselgate only reduced NOx emissions by 41 kt owing to the effectiveness of modern diesel aftertreatment systems.

Verification of a National Emission Inventory and Influence of On-road Vehicle Manufacturer-Level Emissions.

Road vehicles make important contributions to a wide range of pollutant emissions from the street level to global scales. The quantification of emissions from road vehicles is, however, highly challenging given the number of individual sources involved and the myriad factors that influence emissions such as fuel type, emission standard, and driving behavior. In this work, we use highly detailed and comprehensive vehicle emission remote sensing measurements made under real driving conditions to develop new bottom-up inventories that can be compared to official national inventory totals. We find that the total UK passenger car and light-duty van emissions of nitrogen oxides (NOx) are underestimated by 24-32%, and up to 47% in urban areas, compared with the UK national inventory, despite agreement within 1.5% for total fuel used. Emissions of NOx at a country level are also shown to vary considerably depending on the mix of vehicle manufacturers in the fleet. Adopting the on-road mix of vehicle manufacturers for six European countries results in up to a 13.4% range in total emissions of NOx. Accounting for the manufacturer-specific fleets at a country level could have a significant impact on emission estimates of NOx and other pollutants across the European countries, which are not currently reflected in emission inventories.

Underestimated Ammonia Emissions from Road Vehicles.

In this study, we use comprehensive vehicle emission remote sensing measurements of over 230,000 passenger cars to estimate total UK ammonia (NH3) emissions. Estimates are made using "top-down" and "bottom-up" methods that demonstrate good agreement to within 1.1% for total fuel consumed or CO2 emitted. A central component of this study is the comprehensive nature of the bottom-up emission estimates that combine highly detailed remote sensing emission data with over 4000 km of 1 Hz real driving data. Total annual UK NH3 emissions from gasoline passenger cars are estimated to be 7.8 ± 0.3 kt from the bottom-up estimate compared with 3.0 ± 1.7 kt reported by the UK national inventory. An important conclusion from the analysis is that both methodologies confirm that gasoline passenger car NH3 emissions are underestimated by a factor of about 2.6 compared with the 2018 UK National Atmospheric Emissions Inventory. Furthermore, we find that inventory estimates of urban emissions of NH3 for passenger cars are underestimated by a factor of 17.

Strong Temperature Dependence for Light-Duty Diesel Vehicle NO x Emissions.

Diesel-powered road vehicles are important sources for nitrogen oxide (NO x) emissions, and the European passenger fleet is highly dieselised, which has resulted in many European roadside environments being noncompliant with legal air quality standards for nitrogen dioxide (NO2). On the basis of vehicle emission remote sensing data for 300000 light-duty vehicles across the United Kingdom, light-duty diesel NO x emissions were found to be highly dependent on ambient temperature with low temperatures resulting in higher NO x emissions, i.e., a "low temperature NO x emission penalty" was identified. This feature was not observed for gasoline-powered vehicles. Older Euro 3 to 5 diesel vehicles emitted NO x similarly, but vehicles compliant with the latest Euro 6 emission standard emitted less NO x than older vehicles and demonstrated less of an ambient temperature dependence. This ambient temperature dependence is overlooked in current emission inventories but is of importance from an air quality perspective. Owing to Europe's climate, a predicted average of 38% more NO x emissions have burdened Europe when compared to temperatures encountered in laboratory test cycles. However, owing to the progressive elimination of vehicles demonstrating the most severe low temperature NO x penalty, light-duty diesel NO x emissions are likely to decrease more rapidly throughout Europe than currently thought.

Atmospheric vertical profiles of O3, N2O, CH4, CCl2F2, and H2O retrieved from external-cavity quantum-cascade laser heterodyne radiometer measurements.

Atmospheric vertical profiles of ozone, nitrous oxide, methane, dichlorodifluoromethane, and water are retrieved from data collected with a widely tunable external-cavity quantum-cascade laser heterodyne radiometer (EC-QC-LHR) covering a spectral range between 1120 and 1238 cm(-1). The instrument was operated in solar occultation mode during a two-month measurement campaign at Rutherford Appleton Laboratory in Oxfordshire, UK, in winter 2010/2011, and ultrahigh-resolution (60 MHz or 0.002 cm(-1)) transmission spectra were recorded for multiple narrow spectral windows (~1 cm(-1) width) specific to each molecule. The ultrahigh spectral resolution of the EC-QC-LHR allows retrieving altitudinal profiles from transmission spectra that contain only few (1-3) significant absorption lines of a target molecule. Profiles are validated by comparing with European Centre for Medium-Range Weather Forecasts operational atmospheric profiles (ozone and water), with other data in the literature (nitrous oxide, methane, dichlorodifluoromethane), and with retrievals from a lower resolution (600 MHz or 0.02 cm(-1)) Fourier transform spectroscopy data that were also recorded during the measurement campaign.

Ultrafast energy flow in the wake of solution-phase bimolecular reactions.

Vibrational energy flow into reactants, and out of products, plays a key role in chemical reactivity, so understanding the microscopic detail of the pathways and rates associated with this phenomenon is of considerable interest. Here, we use molecular dynamics simulations to model the vibrational relaxation that occurs during the reaction CN + c-C(6)H(12) â†’ HCN + c-C(6)H(11) in CH(2)Cl(2), which produces vibrationally hot HCN. The calculations reproduce the observed energy distribution, and show that HCN relaxation follows multiple timescales. Initial rapid decay occurs through energy transfer to the cyclohexyl co-product within the solvent cage, and slower relaxation follows once the products diffuse apart. Re-analysis of the ultrafast experimental data also provides evidence for the dual timescales. These results, which represent a formal violation of conventional linear response theory, provide a detailed picture of the interplay between fluctuations in organic solvent structure and thermal solution-phase chemistry.

Vibrationally quantum-state-specific dynamics of the reactions of CN radicals with organic molecules in solution.

The dynamics of reactions of CN radicals with cyclohexane, d(12)-cyclohexane, and tetramethylsilane have been studied in solutions of chloroform, dichloromethane, and the deuterated variants of these solvents using ultraviolet photolysis of ICN to initiate a reaction. The H(D)-atom abstraction reactions produce HCN (DCN) that is probed in absorption with sub-picosecond time resolution using ∼500 cm(-1) bandwidth infrared (IR) pulses in the spectral regions corresponding to C-H (or C-D) and C≡N stretching mode fundamental and hot bands. Equivalent IR spectra were obtained for the reactions of CN radicals with the pure solvents. In all cases, the reaction products are formed at early times with a strong propensity for vibrational excitation of the C-H (or C-D) stretching (v(3)) and H-C-N (D-C-N) bending (v(2)) modes, and for DCN products there is also evidence of vibrational excitation of the v(1) mode, which involves stretching of the C≡N bond. The vibrationally excited products relax to the ground vibrational level of HCN (DCN) with time constants of ∼130-270 ps (depending on molecule and solvent), and the majority of the HCN (DCN) in this ground level is formed by vibrational relaxation, instead of directly from the chemical reaction. The time-dependence of reactive production of HCN (DCN) and vibrational relaxation is analysed using a vibrationally quantum-state specific kinetic model. The experimental outcomes are indicative of dynamics of exothermic reactions over an energy surface with an early transition state. Although the presence of the chlorinated solvent may reduce the extent of vibrational excitation of the nascent products, the early-time chemical reaction dynamics in these liquid solvents are deduced to be very similar to those for isolated collisions in the gas phase. The transient IR spectra show additional spectroscopic absorption features centered at 2037 cm(-1) and 2065 cm(-1) (in CHCl(3)) that are assigned, respectively, to CN-solvent complexes and recombination of I atoms with CN radicals to form INC molecules. These products build up rapidly, with respective time constants of 8-26 and 11-22 ps. A further, slower rise in the INC absorption signal (with time constant >500 ps) is attributed to diffusive recombination after escape from the initial solvent cage and accounts for more than 2/3 of the observed INC.

Vibrationally quantum-state-specific reaction dynamics of H atom abstraction by CN radical in solution.

Solvent collisions can often mask initial disposition of energy to the products of solution-phase chemical reactions. Here, we show with transient infrared absorption spectra obtained with picosecond time resolution that the nascent HCN products of reaction of CN radicals with cyclohexane in chlorinated organic solvents exhibit preferential excitation of one quantum of the C-H stretching mode and up to two quanta of the bending mode. On time scales of approximately 100 to 300 picoseconds, the HCN products undergo relaxation to the vibrational ground state by coupling to the solvent bath. Comparison with reactions of CN radicals with alkanes in the gas phase, known to produce HCN with greater C-H stretch and bending mode excitation (up to two and approximately six quanta, respectively), indicates partial damping of the nascent product vibrational motion by the solvent. The transient infrared spectra therefore probe solvent-induced modifications to the reaction free energy surface and chemical dynamics.

Chemical Reaction Dynamics in Liquid Solutions.

The dynamics of bimolecular chemical reactions can be examined in liquid solutions using infrared absorption spectroscopy with picosecond time resolution. On such short time scales, the transient absorption spectra reveal vibrational mode and quantum-state-specific energy disposal, followed by vibrational relaxation as the energy is dissipated to the surrounding solvent. Comparison with energy disposal measurements for gas-phase reactions under single-collision conditions offers direct insights into the modification of the energy landscape and the nuclear dynamics in the presence of the solvent. The reactions of CN radicals with organic molecules in chlorinated solvents exemplify the dynamical information that can be obtained. The potential to extend such experiments to a range of reactions and solvents is discussed.

Velocity map imaging the dynamics of the reactions of Cl atoms with neopentane and tetramethylsilane.

The reactions of ground state Cl((2)P(3/2)) atoms with neopentane and tetramethylsilane have been studied at collision energies of 7.9+/-2.0 and 8.2+/-2.0 kcal mol(-1), respectively. The nascent HCl(v=0,J) products were probed using resonance enhanced multiphoton ionization spectroscopy combined with velocity map imaging (VMI) to determine the rotational level population distributions, differential cross sections (DCSs), and product translational energy distributions. The outcomes from PHOTOLOC and dual beam methods are compared and are discussed in light of previous studies of the reactions of Cl atoms with other saturated hydrocarbons, including a recent crossed molecular beam and VMI investigation of the reaction of Cl atoms with neopentane [Estillore et al., J. Chem. Phys. 132, 164313 (2010)]. Rotational distributions were observed to be cold, consistent with the reactions proceeding via a transition state with a collinear Cl-H-C moiety. The DCSs for both reactions are forward peaked but show scatter across a broad angular range. Interpretation using a model based on linear dependence of scattering angle on impact parameter indicates that the probability of reaction is approximately constant across all allowed impact parameters. Product translational energy distributions from dual beam experiments have mean values, expressed as fractions of the total available energy, of 0.67 (Cl+neopentane) and 0.64 (Cl+tetramethylsilane) that are consistent with a kinematic model for the reaction in which the translational energy of the reactants is conserved into product translational energy.

Velocity map imaging of the dynamics of bimolecular chemical reactions.

The experimental technique of velocity map imaging (VMI) enables measurements to be made of the dynamics of chemical reactions that are providing unprecedented insights about reactive scattering. This perspective article illustrates how VMI, in combination with crossed-molecular beam, dual-beam or photo-initiated (Photoloc) methods, can reveal correlated information on the vibrational quantum states populated in the two products of a reaction, and the angular scattering of products (the differential cross section) formed in specific rotational and vibrational levels. Reactions studied by VMI techniques are being extended to those of polyatomic molecules or radicals, and of molecular ions. Subtle quantum-mechanical effects in bimolecular reactions can provide distinct signatures in the velocity map images, and are exemplified here by non-adiabatic dynamics on coupled potential energy surfaces, and by experimental evidence for scattering resonances.

Adiabatic and nonadiabatic dynamics in the CH3(CD3)+HCl reaction.

The scattering dynamics leading to the formation of Cl (2P(3/2)) and Cl* (2P(1/2)) products of the CH(3)+HCl reaction (at a mean collision energy =22.3 kcal mol(-1)) and the Cl (2P(3/2)) products of the CD(3)+HCl reaction (at =19.4 kcal mol(-1)) have been investigated by using photodissociation of CH(3)I and CD(3)I as sources of translationally hot methyl radicals and velocity map imaging of the Cl atom products. Image analysis with a Legendre moment fitting procedure demonstrates that, in all three reactions, the Cl/Cl* products are mostly forward scattered with respect to the HCl in the center-of-mass (c.m.) frame but with a backward scattered component. The distributions of the fraction of the available energy released as translation peak at f(t)=0.31-0.33 for all the reactions, with average values that lie in the range =0.42-0.47. The detailed analysis indicates the importance of collision energy in facilitating the nonadiabatic transitions that lead to Cl* production. The similarities between the c.m.-frame scattering and kinetic energy release distributions for Cl and Cl* channels suggest that the nonadiabatic transitions to a low-lying excited potential energy surface (PES) correlating to Cl* products occur after passage through the transition state region on the ground-state PES. Branching fractions for Cl* are determined to be 0.14+/-0.02 for the CH(3)+HCl reaction and 0.20+/-0.03 for the CD(3)+HCl reaction. The difference cannot be accounted for by changes in collision energy, mass effects, or vibrational excitation of the photolytically generated methyl radical reagents and instead suggests that the low-frequency bending modes of the CD(3)H or CH(4) coproduct are important mediators of the nonadiabatic couplings occurring in this reaction system.

The dynamics of reaction of Cl atoms with tetramethylsilane.

Rotational state distributions and state-selected CM-frame angular distributions were measured for HCl (v' = 0, j') products from the reaction of Cl-atoms with tetramethylsilane (TMS) under single collision conditions at a collision energy, E(coll), of 8.2 +/- 2.0 kcal mol(-1). The internal excitation of these products was very low with only 2% of the total energy available partitioned into HCl rotation. A transition state with a quasi-linear C-H-Cl moiety structure was computed and used to explain this finding. A backward peaking differential cross section was also reported together with a product translational energy (T') distribution with a maximum at T' approximately E(coll). This scattering behaviour is accounted for by reactions proceeding through a tight transition state on a highly skewed potential energy surface, which favours collisions at low impact parameters with a strong kinematic constraint on the internal excitation of the products. The large Arrhenius pre-exponential factor previously reported for this reaction is reconciled with the tight differential scattering observed in our study by considering the large size of the TMS molecule.

Imaging the dynamics of reactions between Cl atoms and the cyclic ethers oxirane and oxetane.

Direct current slice velocity map ion images of the HCl(nu' = 0, J') products from the photoinitiated reactions of ground state Cl atoms with ethane, oxirane (c-C2H4O), and oxetane (c-C3H6O), at respective mean collision energies of 5.5, 6.5, and 7.3 kcal mol-1(-1), were analyzed using a Legendre moment fitting procedure. The experimental method and the fitting technique were tested by comparing the derived center-of-mass (CM) frame angular scattering distribution for the HCl(v' = 0, J' = 1) products from the reaction of Cl + C2H6 with those determined by Suits and co-workers from a crossed molecular beam experiment. For the Cl + c-C2H4O reaction, a broad, forward, and backward peaking CM frame angular distribution of HCl(nu' = 0, J' = 2) products was determined, with an average fraction of the available energy released as product translational energy of f t, equal to 0.52 +/- 0.18. The HCl consumes only 1% of the available energy, and conservation arguments dictate that the radical coproduct is significantly internally excited, corresponding to an average fraction of the available energy of f int(c-C2H3O), equal to 0.47 +/- 0.18. For the reaction of oxetane with Cl atoms, abstraction of H atoms is possible from carbon atoms from positions either alpha or beta to the O atom. The contributions to the reaction from these two H-atom abstraction channels were estimated to be 63 and 37%, consistent with an unbiased propensity for removal of alpha- and beta-H atoms that are present in 2:1 abundance. The angular scatter of products in the CM frame is also broad and forward-backward peaking and is reminiscent of the products of the Cl + CH3OH and CH3OCH3 reactions. The derived mean fraction of the available energy channelled into product translation is f t = 0.54 +/- 0.12 for each of the two abstraction pathways. With only a small amount of energy in the rotation of the HCl(nu' = 0), the remainder is accounted for by excitation of the radical coproduct internal modes, with f int(c-C3H5O) = 0.42 +/- 0.12 for both alpha- and beta-H abstraction. The broad product scattering in the CM frame observed for both reactions of Cl atoms with the cyclic ethers is consistent with reactive collisions over a wide range of impact parameters, as might be expected for barrierless reactions with loose transition states.

Imaging the nonadiabatic dynamics of the CH3 + HCl reaction.

LAB-frame velocity distributions of Cl-atoms produced in the photoinitiated reaction of CH(3) radicals with HCl have been measured for both the ground Cl ((2)P(3/2)) and excited Cl* ((2)P(1/2)) spin-orbit states using a DC slice velocity-map ion imaging technique. The similarity of these distributions, as well as the average internal excitation of methane co-products for both Cl and Cl* pathways, suggest that all the reactive flux proceeds through the same transition state on the ground potential energy surface (PES) and that the couplings which promote nonadiabatic transitions to the excited PES correlating to Cl* occur later in the exit channel, beyond the TS region. The nature of these couplings is discussed in light of initial vibrational excitation of CH(3) radicals as well as previously reported nonadiabatic reactivity in other polyatomic molecule reactions. Furthermore, the scattering of the reaction products, derived using the photoloc method, suggests that at the high collision energy of our experiment (E(coll) = 22.3 kcal mol(-1)), large impact parameter collisions are favoured with a reduced kinematic constraint on the internal excitation of the methane co-product.

N-Acetylcysteine improves renal dysfunction, ameliorates kidney damage and decreases blood pressure in salt-sensitive hypertension.

BACKGROUND: Salt-sensitive hypertension in humans and experimental animals causes progressive increases in renal damage and dysfunction. The Dahl salt-sensitive (S) rat closely mimics human salt-sensitive hypertension. AIM: Our goal was to test the hypothesis that enhancing the glutathione system with dietary N-acetylcysteine administration in Dahl S rats on a high sodium intake for 5 weeks will attenuate the increases in arterial pressure, the decreases in renal hemodynamics and the increases in renal damage that normally occur in S rats on high sodium. METHODS: Forty-four 7- to 8-week-old Dahl S/Rapp strain rats were maintained on a high sodium (8%), high sodium + N-acetylcysteine (4 g/kg per day), or low sodium (0.3%) diet for 5 weeks. Rats had arterial and venous catheters implanted at day 21. RESULTS: By day 35 in the high-sodium rats, N-acetylcysteine treatment significantly increased the renal reduced-to-oxidized glutathione ratio, glomerular filtration rate, and renal plasma flow, and decreased renal cortical and medullary O2 release, urinary protein excretion, renal tubulointerstitial damage and glomerular necrosis. At this time, mean arterial pressure increased to 183 +/- 1 mmHg, and N-acetylcysteine reduced this arterial pressure to 121 +/- 4 mmHg. By day 35 in S high-sodium rats, N-acetylcysteine had caused a 91% decrease in glomerular necrosis and an 83% decrease in tubulointerstitial damage. CONCLUSIONS: In Dahl S rats on high sodium intake, arterial pressure increases significantly and renal injury is pronounced. Treatment with N-acetylcysteine enhances the renal glutathione system, improves renal dysfunction and markedly decreases arterial pressure and renal injury in Dahl salt-sensitive hypertension.