Wildland-urban interface wildfire increases metal contributions to stormwater runoff in Paradise, California.

The 2018 Camp Fire was a large late-year (November) wildfire that produced an urban firestorm in the Town of Paradise, California, USA, and destroyed more than 18 000 structures. Runoff from burned wildland areas is known to contain ash, which can transport contaminants including metals into nearby watersheds. However, due to historically infrequent occurrences, the effect of wildland-urban interface (WUI) fires, such as the Camp Fire, on surface water quality has not been well-characterized. Therefore, this study investigated the effects of widespread urban burning on surface water quality in major watersheds of the Camp Fire area. Between November 2018 and May 2019, 140 surface water samples were collected, including baseflow and stormflow, from burned and unburned watersheds with varying extent of urban development. Samples were analyzed for total and filter-passing metals, dissolved organic carbon, major anions, and total suspended solids. Ash and debris from the Camp Fire contributed metals to downstream watersheds via runoff throughout the storm season. Increases in concentration up to 200-fold were found for metals Cr, Cu, Ni, Pb, and Zn in burned watersheds compared to pre-fire values. Total concentrations of Al, Cd, Cu, Pb, and Zn exceeded EPA aquatic habitat acute criteria by up to 16-fold for up to five months after the fire. To assess possible transport mechanisms and bioavailability, a subset of 18 samples was analyzed using four filters with nominal pore sizes ranging from 0.22 to 1.2 µm to determine the particulate size distribution of metals. Trace and major metals (Al, Ba, Co, Cr, Cu, Fe, Hg, Mn, Ni, Pb, and Zn) were found mostly associated with larger grain sizes (>0.45 µm), and some metals (Al, Cr, Fe, and Pb) also included a substantial colloidal phase (0.22 to 0.45 µm). This study suggests that fires in the wildland-urban interface increase metal concentrations, mainly through particulate driven transport. The metals with the largest increases are likely from anthropogenic disaster materials, though biomass ash also is a major contributor to water quality. The increase in metals following WUI burning may have adverse ecological impacts.

Composition and Origin of Surface Casing Fluids in a Major US Oil- and Gas-Producing Region.

Fluids leaked from oil and gas wells often originate from their surface casing─a steel pipe installed beneath the deepest underlying source of potable groundwater that serves as the final barrier around the well system. In this study, we analyze a regulatory dataset of surface casing geochemical samples collected from 2573 wells in northeastern Colorado─the only known publicly available dataset of its kind. Thermogenic gas was present in the surface casings of 96.2% of wells with gas samples. Regulatory records indicate that 73.3% of these wells were constructed to isolate the formation from which the gas originated with cement. This suggests that gas migration into the surface casing annulus predominantly occurs through compromised barriers (e.g., steel casings or cement seals), indicative of extensive integrity issues in the region. Water was collected from 22.6% of sampled surface casings. Benzene, toluene, ethylbenzene, and xylenes were detected in 99.7% of surface casing water samples tested for these compounds, which may be due to the presence of leaked oil, natural gas condensate, or oil-based drilling mud. Our findings demonstrate the value of incorporating surface casing geochemical analysis in well integrity monitoring programs to identify integrity issues and focus leak mitigation efforts.

Vulnerability of Groundwater Resources Underlying Unlined Produced Water Ponds in the Tulare Basin of the San Joaquin Valley, California.

The San Joaquin Valley (SJV) in California is one of the most agriculturally productive regions in the world relying in part on groundwater for irrigation and for domestic or municipal water supply for nearly 4 million residents. One area of growing concern in the SJV is potential impact to groundwater resources from ongoing and historical disposal of oilfield-produced water into unlined produced water ponds (PWPs). In this investigation, we utilized available information on composition of produced water disposed into unlined PWPs and levels of total dissolved solids in underlying groundwater to demonstrate that this disposal practice, both past and present, poses risks to groundwater resources, especially in the Tulare Basin in the southern SJV. Groundwater monitoring at unlined PWP facilities is relatively sparse, but where monitoring has occurred, impact to aquifers used for public and agricultural water supply has been observed and has proven to be too expensive to actively remediate. Results of this investigation should inform policy discussions in California and other locations where disposal of produced water into unlined impoundments occurs, especially at locations that overlie groundwater resources.

Public data from three US states provide new insights into well integrity.

Oil and gas wells with compromised integrity are a concern because they can potentially leak hydrocarbons or other fluids into groundwater and/or the atmosphere. Most states in the United States require some form of integrity testing, but few jurisdictions mandate widespread testing and open reporting on a scale informative for leakage risk assessment. In this study, we searched 33 US state oil and gas regulatory agency databases and identified records useful for evaluating well integrity in Colorado, New Mexico, and Pennsylvania. In total, we compiled 474,621 testing records from 105,031 wells across these states into a uniform dataset. We found that 14.1% of wells tested prior to 2018 in Pennsylvania exhibited sustained casing pressure (SCP) or casing vent flow (CVF)-two indicators of compromised well integrity. Data from different hydrocarbon-producing regions within Colorado and New Mexico revealed a wider range (0.3 to 26.5%) of SCP and/or CVF occurrence than previously reported, highlighting the need to better understand regional trends in well integrity. Directional wells were more likely to exhibit SCP and/or CVF than vertical wells in Colorado and Pennsylvania, and their installation corresponded with statewide increases in SCP and/or CVF occurrence in Colorado (2005 to 2009) and Pennsylvania (2007 to 2011). Testing the ground around wells for indicators of gas leakage is not a widespread practice in the states considered. However, 3.0% of Colorado wells tested and 0.1% of New Mexico wells tested exhibited a degree of SCP sufficient to potentially induce leakage outside the well.

Microbial and Biogeochemical Indicators of Methane in Groundwater Aquifers of the Denver Basin, Colorado.

The presence of methane and other hydrocarbons in domestic-use groundwater aquifers poses significant environmental and human health concerns. Isotopic measurements are often relied upon as indicators of groundwater aquifer contamination with methane. While these parameters are used to infer microbial metabolisms, there is growing evidence that isotopes present an incomplete picture of subsurface microbial processes. This study examined the relationships between microbiology and chemistry in groundwater wells located in the Denver-Julesburg Basin of Colorado, a rapidly urbanizing area with active oil and gas development. A primary goal was to determine if microbial data can reliably indicate the quantities and sources of groundwater methane. Comprehensive chemical and molecular analyses were performed on 39 groundwater well samples from five aquifers. Elevated methane concentrations were found in only one aquifer, and both isotopic and microbial data support a microbial origin. Microbial parameters had similar explanatory power as chemical parameters for predicting sample methane concentrations. Furthermore, a subset of samples with unique microbiology corresponded with unique chemical signatures that may be useful indicators of methane gas migration, potentially from nearby coal seams interacting with the aquifer. Microbial data may allow for more accurate determination of groundwater contamination and improved long-term water quality monitoring compared solely to isotopic and chemical data in areas with microbial methane.

Geochemical Factors Controlling Dissolved Elemental Mercury and Methylmercury Formation in Alaskan Wetlands of Varying Trophic Status.

The transformations of aqueous inorganic divalent mercury (Hg(II)i) to volatile dissolved gaseous mercury (Hg(0)(aq)) and toxic methylmercury (MeHg) govern mercury bioavailability and fate in northern ecosystems. This study quantified concentrations of aqueous mercury species (Hg(II)i, Hg(0)(aq), MeHg) and relevant geochemical constituents in pore waters of eight Alaskan wetlands that differ in trophic status (i.e., bog-to-fen gradient) to gain insight on processes controlling dark Hg(II)i reduction and Hg(II)i methylation. Regardless of wetland trophic status, positive correlations were observed between pore water Hg(II)i and dissolved organic carbon (DOC) concentrations. The concentration ratio of Hg(0)(aq) to Hg(II)i exhibited an inverse relationship to Hg(II)i concentration. A ubiquitous pathway for Hg(0)(aq) formation was not identified based on geochemical data, but we surmise that dissolved organic matter (DOM) influences mercury retention in wetland pore waters by complexing Hg(II)i and decreasing the concentration of volatile Hg(0)(aq) relative to Hg(II)i. There was no evidence of Hg(0)(aq) abundance directly limiting mercury methylation. The concentration of MeHg relative to Hg(II)i was greatest in wetlands of intermediate trophic status, and geochemical data suggest mercury methylation pathways vary between wetlands. Our insights on geochemical factors influencing aqueous mercury speciation should be considered in context of the long-term fate of mercury in northern wetlands.

Degradation of polyethylene glycols and polypropylene glycols in microcosms simulating a spill of produced water in shallow groundwater.

Polyethylene glycols (PEGs) and polypropylene glycols (PPGs) are frequently used in hydraulic fracturing fluids and have been detected in water returning to the surface from hydraulically fractured oil and gas wells in multiple basins. We identified degradation pathways and kinetics for PEGs and PPGs under conditions simulating a spill of produced water to shallow groundwater. Sediment-groundwater microcosm experiments were conducted using four produced water samples from two Denver-Julesburg Basin wells at early and late production. High-resolution mass spectrometry was used to identify the formation of mono- and di-carboxylated PEGs and mono-carboxylated PPGs, which are products of PEG and PPG biodegradation, respectively. Under oxic conditions, first-order half-lives were more rapid for PEGs (<0.4-1.1 d) compared to PPGs (2.5-14 d). PEG and PPG degradation corresponded to increased relative abundance of primary alcohol dehydrogenase genes predicted from metagenome analysis of the 16S rRNA gene. Further degradation was not observed under anoxic conditions. Our results provide insight into the differences between the degradation rates and pathways of PEGs and PPGs, which may be utilized to better characterize shallow groundwater contamination following a release of produced water.

Water Stress from High-Volume Hydraulic Fracturing Potentially Threatens Aquatic Biodiversity and Ecosystem Services in Arkansas, United States.

Demand for high-volume, short duration water withdrawals could create water stress to aquatic organisms in Fayetteville Shale streams sourced for hydraulic fracturing fluids. We estimated potential water stress using permitted water withdrawal volumes and actual water withdrawals compared to monthly median, low, and high streamflows. Risk for biological stress was considered at 20% of long-term median and 10% of high- and low-flow thresholds. Future well build-out projections estimated potential for continued stress. Most water was permitted from small, free-flowing streams and "frack" ponds (dammed streams). Permitted 12-h pumping volumes exceeded median streamflow at 50% of withdrawal sites in June, when flows were low. Daily water usage, from operator disclosures, compared to median streamflow showed possible water stress in 7-51% of catchments from June-November, respectively. If 100% of produced water was recycled, per-well water use declined by 25%, reducing threshold exceedance by 10%. Future water stress was predicted to occur in fewer catchments important for drinking water and species of conservation concern due to the decline in new well installations and increased use of recycled water. Accessible and precise withdrawal and streamflow data are critical moving forward to assess and mitigate water stress in streams that experience high-volume withdrawals.

Effects of Sulfide Concentration and Dissolved Organic Matter Characteristics on the Structure of Nanocolloidal Metacinnabar.

Understanding the speciation of divalent mercury (Hg(II)) in aquatic systems containing dissolved organic matter (DOM) and sulfide is necessary to predict the conversion of Hg(II) to bioavailable methylmercury. We used X-ray absorption spectroscopy to characterize the structural order of mercury in Hg(II)-DOM-sulfide systems for a range of sulfide concentration (1-100 µM), DOM aromaticity (specific ultraviolet absorbance (SUVA254)), and Hg(II)-DOM and Hg(II)-DOM-sulfide equilibration times (4-142 h). In all systems, Hg(II) was present as structurally disordered nanocolloidal metacinnabar (ß-HgS). ß-HgS nanocolloids were significantly smaller or less ordered at lower sulfide concentration, as indicated by under-coordination of Hg(II) in ß-HgS. The size or structural order of ß-HgS nanocolloids increased with increasing sulfide abundance and decreased with increasing SUVA254 of the DOM. The Hg(II)-DOM or Hg(II)-DOM-sulfide equilibration times did not significantly influence the extent of structural order in nanocolloidal ß-HgS. Geochemical factors that control the structural order of nanocolloidal ß-HgS, which are expected to influence nanocolloid surface reactivity and solubility, should be considered in the context of mercury bioavailability.

Inhibition of Biodegradation of Hydraulic Fracturing Compounds by Glutaraldehyde: Groundwater Column and Microcosm Experiments.

The rapid expansion of unconventional oil and gas development has raised concerns about the potential contamination of aquifers; however, the groundwater fate and transport of hydraulic fracturing fluid compounds and mixtures remains a significant data gap. Degradation kinetics of five hydraulic fracturing compounds (2-propanol, ethylene glycol, propargyl alcohol, 2-butoxyethanol, and 2-ethylhexanol) in the absence and presence of the biocide glutaraldehyde were investigated under a range of redox conditions using sediment-groundwater microcosms and flow-through columns. Microcosms were used to elucidate biodegradation inhibition at varying glutaraldehyde concentrations. In the absence of glutaraldehyde, half-lives ranged from 13 d to >93 d. Accurate mass spectrometry indicated that a trimer was the dominant aqueous-phase glutaraldehyde species. Microbial inhibition was observed at glutaraldehyde trimer concentrations as low as 5 mg L-1, which demonstrated that the trimer retained some biocidal activity. For most of the compounds, biodegradation rates slowed with increasing glutaraldehyde concentrations. For many of the compounds, degradation was faster in the columns than the microcosms. Four compounds (2-propanol, ethylene glycol, propargyl alcohol, and 2-butoxyethanol) were found to be both mobile and persistent in groundwater under a range of redox conditions. The glutaraldehyde trimer and 2-ethylhexanol were more rapidly degraded, particularly under oxic conditions.

Temporal characterization of flowback and produced water quality from a hydraulically fractured oil and gas well.

This study examined water quality, naturally-occurring radioactive materials (NORM), major ions, trace metals, and well flow data for water used and produced from start-up to operation of an oil and gas producing hydraulically-fractured well (horizontal) in the Denver-Julesburg (DJ) Basin in northeastern Colorado. Analysis was conducted on the groundwater used to make the fracturing fluid, the fracturing fluid itself, and nine flowback/produced water samples over 220days of operation. The chemical oxygen demand of the wastewater produced during operation decreased from 8200 to 2500mg/L, while the total dissolved solids (TDS) increased in this same period from 14,200 to roughly 19,000mg/L. NORM, trace metals, and major ion levels were generally correlated with TDS, and were lower than other shale basins (e.g. Marcellus and Bakken). Although at lower levels, the salinity and its origin appear to be the result of a similar mechanism to that of other shale basins when comparing Cl/Br, Na/Br, and Mg/Br ratios. Volumes of returned wastewater were low, with only 3% of the volume injected (11millionliters) returning as flowback by day 15 and 30% returning by day 220. Low levels of TDS indicate a potentially treatment-amenable wastewater, but low volumes of flowback could limit onsite reuse in the DJ Basin. These results offer insight into the temporal water quality changes in the days and months following flowback, along with considerations and implications for water reuse in future hydraulic fracturing or for environmental discharge.

Spatial Dependence of Reduced Sulfur in Everglades Dissolved Organic Matter Controlled by Sulfate Enrichment.

Sulfate inputs to the Florida Everglades stimulate sulfidic conditions in freshwater wetland sediments that affect ecological and biogeochemical processes. An unexplored implication of sulfate enrichment is alteration of the content and speciation of sulfur in dissolved organic matter (DOM), which influences the reactivity of DOM with trace metals. Here, we describe the vertical and lateral spatial dependence of sulfur chemistry in the hydrophobic organic acid fraction of DOM from unimpacted and sulfate-impacted Everglades wetlands using X-ray absorption spectroscopy and ultrahigh-resolution mass spectrometry. Spatial variation in DOM sulfur content and speciation reflects the degree of sulfate enrichment and resulting sulfide concentrations in sediment pore waters. Sulfur is incorporated into DOM predominantly as highly reduced species in sulfidic pore waters. Sulfur-enriched DOM in sediment pore waters exchanges with overlying surface waters and the sulfur likely undergoes oxidative transformations in the water column. Across all wetland sites and depths, the total sulfur content of DOM correlated with the relative abundance of highly reduced sulfur functionality. The results identify sulfate input as a primary determinant on DOM sulfur chemistry to be considered in the context of wetland restoration and sulfur and trace metal cycling.

Surface Casing Pressure As an Indicator of Well Integrity Loss and Stray Gas Migration in the Wattenberg Field, Colorado.

The risk of environmental contamination by oil and gas wells depends strongly on the frequency with which they lose integrity. Wells with compromised integrity typically exhibit pressure in their outermost annulus (surface casing pressure, SfCP) due to gas accumulation. SfCP is an easily measured but poorly documented gauge of well integrity. Here, we analyze SfCP data from the Colorado Oil and Gas Conservation Commission database to evaluate the frequency of well integrity loss in the Wattenberg Test Zone (WTZ), within the Wattenberg Field, Colorado. Deviated and horizontal wells were found to exhibit SfCP more frequently than vertical wells. We propose a physically meaningful well-specific critical SfCP criterion, which indicates the potential for a well to induce stray gas migration. We show that 270 of 3923 wells tested for SfCP in the WTZ exceeded critical SfCP. Critical SfCP is strongly controlled by the depth of the surface casing. Newer horizontal wells, drilled during the unconventional drilling boom, exhibited critical SfCP less frequently than other wells because they were predominantly constructed with deeper surface casings. Thus, they pose a lower risk for inducing stray gas migration than legacy vertical or deviated wells with surface casings shorter than modern standards.

Unconventional oil and gas spills: Materials, volumes, and risks to surface waters in four states of the U.S.

Extraction of oil and gas from unconventional sources, such as shale, has dramatically increased over the past ten years, raising the potential for spills or releases of chemicals, waste materials, and oil and gas. We analyzed spill data associated with unconventional wells from Colorado, New Mexico, North Dakota and Pennsylvania from 2005 to 2014, where we defined unconventional wells as horizontally drilled into an unconventional formation. We identified materials spilled by state and for each material we summarized frequency, volumes and spill rates. We evaluated the environmental risk of spills by calculating distance to the nearest stream and compared these distances to existing setback regulations. Finally, we summarized relative importance to drinking water in watersheds where spills occurred. Across all four states, we identified 21,300 unconventional wells and 6622 reported spills. The number of horizontal well bores increased sharply beginning in the late 2000s; spill rates also increased for all states except PA where the rate initially increased, reached a maximum in 2009 and then decreased. Wastewater, crude oil, drilling waste, and hydraulic fracturing fluid were the materials most often spilled; spilled volumes of these materials largely ranged from 100 to 10,000L. Across all states, the average distance of spills to a stream was highest in New Mexico (1379m), followed by Colorado (747m), North Dakota (598m) and then Pennsylvania (268m), and 7.0, 13.3, and 20.4% of spills occurred within existing surface water setback regulations of 30.5, 61.0, and 91.4m, respectively. Pennsylvania spills occurred in watersheds with a higher relative importance to drinking water than the other three states. Results from this study can inform risk assessments by providing improved input parameters on volume and rates of materials spilled, and guide regulations and the management policy of spills.

Identification of polypropylene glycols and polyethylene glycol carboxylates in flowback and produced water from hydraulic fracturing.

The purpose of the study was to separate and identify the unknown surfactants present in flowback and produced water from oil and gas wells in the Denver-Julesburg Basin (Niobrara Formation) in Weld County, Colorado, USA. Weld County has been drilled extensively during the last five years for oil and gas between 7000-8000 feet below land-surface. Polypropylene glycols (PPGs) and polyethylene glycols carboxylates (PEG-Cs) were found for the first time in these flowback and produced water samples. These ethoxylated surfactants may be used as friction reducers, clay stabilizers, and surfactants. Ultrahigh-performance liquid chromatography/quadrupole-time-of-flight mass spectrometry (UHPLC/QTOF-MS) was used to separate and identify the different classes of PPGs, PEG-Cs, and their isomers. The Kendrick mass scale was applied along with mass spectrometry/mass spectrometry (MS-MS) with accurate mass for rapid and unequivocal identification. The PPGs and their isomers occur at the ppm concentration range and may be useful as "fingerprints" of hydraulic-fracturing. Comparing these detections to the compounds used in the fracturing process from FracFocus 3.0 (https://fracfocus.org), it appears that both PPGs and polyethylene glycols (PEGs) are commonly named as additives, but the PEG-Cs have not been reported. The PEG-Cs may be trace impurities or degradation products of PEGs.

Groundwater methane in relation to oil and gas development and shallow coal seams in the Denver-Julesburg Basin of Colorado.

Unconventional oil and gas development has generated intense public concerns about potential impacts to groundwater quality. Specific pathways of contamination have been identified; however, overall rates of contamination remain ambiguous. We used an archive of geochemical data collected from 1988 to 2014 to determine the sources and occurrence of groundwater methane in the Denver-Julesburg Basin of northeastern Colorado. This 60,000-km(2) region has a 60-y-long history of hydraulic fracturing, with horizontal drilling and high-volume hydraulic fracturing beginning in 2010. Of 924 sampled water wells in the basin, dissolved methane was detected in 593 wells at depths of 20-190 m. Based on carbon and hydrogen stable isotopes and gas molecular ratios, most of this methane was microbially generated, likely within shallow coal seams. A total of 42 water wells contained thermogenic stray gas originating from underlying oil and gas producing formations. Inadequate surface casing and leaks in production casing and wellhead seals in older, vertical oil and gas wells were identified as stray gas migration pathways. The rate of oil and gas wellbore failure was estimated as 0.06% of the 54,000 oil and gas wells in the basin (lower estimate) to 0.15% of the 20,700 wells in the area where stray gas contamination occurred (upper estimate) and has remained steady at about two cases per year since 2001. These results show that wellbore barrier failure, not high-volume hydraulic fracturing in horizontal wells, is the main cause of thermogenic stray gas migration in this oil- and gas-producing basin.

Water acquisition and use during unconventional oil and gas development and the existing data challenges: Weld and Garfield counties, CO.

Colorado has recently experienced a significant increase in unconventional oil and gas development, with the greatest concentration of activity occurring in Weld and Garfield counties. Water for oil and gas development has received much attention mainly because water resources are limited in these regions and development is taking place closer to populated areas than it did in the past. Publicly available datasets for the period 2011-2014 were used to identify water acquisition strategies and sources of water used for oil and gas. In addition, the annual average water used in these two counties was quantified and compared to their total water withdrawals. The analysis also quantified the water needed for different well types, along with the flowback water that is retrieved. Weld and Garfield counties are dissimilar in respect to development practices for water acquisition, preferred well type and the fate of flowback water. But at the same time, this difference displays how geological characteristics, water availability, and administration localities are the key elements along with economics in the decision making process within the oil and gas sector. This effort also revealed data challenges regarding accessibility and reliability of reported information, and the need for additional data. Improving the understanding of the unconventional oil and gas sector's water use will help identify possible effects and tradeoffs on the local/regional level, which could diminish the conflicting perspectives that shape the water-energy discussions. This would complement the ability to make informed water resources planning and management decisions that are environmentally and socially acceptable.

Estimating mercury emissions resulting from wildfire in forests of the Western United States.

Understanding the emissions of mercury (Hg) from wildfires is important for quantifying the global atmospheric Hg sources. Emissions of Hg from soils resulting from wildfires in the Western United States was estimated for the 2000 to 2013 period, and the potential emission of Hg from forest soils was assessed as a function of forest type and soil-heating. Wildfire released an annual average of 3100±1900kg-Hgy(-1) for the years spanning 2000-2013 in the 11 states within the study area. This estimate is nearly 5-fold lower than previous estimates for the study region. Lower emission estimates are attributed to an inclusion of fire severity within burn perimeters. Within reported wildfire perimeters, the average distribution of low, moderate, and high severity burns was 52, 29, and 19% of the total area, respectively. Review of literature data suggests that that low severity burning does not result in soil heating, moderate severity fire results in shallow soil heating, and high severity fire results in relatively deep soil heating (<5cm). Using this approach, emission factors for high severity burns ranged from 58 to 640µg-Hgkg-fuel(-1). In contrast, low severity burns have emission factors that are estimated to be only 18-34µg-Hgkg-fuel(-1). In this estimate, wildfire is predicted to release 1-30gHgha(-1) from Western United States forest soils while above ground fuels are projected to contribute an additional 0.9 to 7.8gHgha(-1). Land cover types with low biomass (desert scrub) are projected to release less than 1gHgha(-1). Following soil sources, fuel source contributions to total Hg emissions generally followed the order of duff>wood>foliage>litter>branches.

Colloid Mobilization in a Fractured Soil: Effect of Pore-Water Exchange between Preferential Flow Paths and Soil Matrix.

Exchange of water and solutes between contaminated soil matrix and bulk solution in preferential flow paths has been shown to contribute to the long-term release of dissolved contaminants in the subsurface, but whether and how this exchange can affect the release of colloids in a soil are unclear. To examine this, we applied rainfall solutions of different ionic strength on an intact soil core and compared the resulting changes in effluent colloid concentration through multiple sampling ports. The exchange of water between soil matrix and the preferential flow paths leading to each port was characterized on the basis of the bromide (conservative tracer) breakthrough time at the port. At individual ports, two rainfalls of a certain ionic strength mobilized different amounts of colloids when the soil was pre-exposed to a solution of lower or higher ionic strength. This result indicates that colloid mobilization depended on rainfall solution history, which is referred as colloid mobilization hysteresis. The extent of hysteresis was increased with increases in exchange of pore water and solutes between preferential flow paths and matrix. The results indicate that the soil matrix exchanged the old water from the previous infiltration with new infiltrating water during successive infiltration and changed the pore water chemistry in the preferential flow paths, which in turn affected the release of soil colloids. Therefore, rainfall solution history and soil heterogeneity must be considered to assess colloid mobilization in the subsurface. These findings have implications for the release of colloids, colloid-associated contaminants, and pathogens from soils.

Colloid Mobilization in a Fractured Soil during Dry-Wet Cycles: Role of Drying Duration and Flow Path Permeability.

In subsurface soils, colloids are mobilized by infiltrating rainwater, but the source of colloids and the process by which colloids are generated between rainfalls are not clear. We examined the effect of drying duration and the spatial variation of soil permeability on the mobilization of in situ colloids in intact soil cores (fractured and heavily weathered saprolite) during dry-wet cycles. Measuring water flux at multiple sampling ports at the core base, we found that water drained through flow paths of different permeability. The duration of antecedent drying cycles affected the amount of mobilized colloids, particularly in high-flux ports that received water from soil regions with a large number of macro- and mesopores. In these ports, the amount of mobilized colloids increased with increased drying duration up to 2.5 days. For drying durations greater than 2.5 days, the amount of mobilized colloids decreased. In contrast, increasing drying duration had a limited effect on colloid mobilization in low-flux ports, which presumably received water from soil regions with fewer macro- and mesopores. On the basis of these results, we attribute this dependence of colloid mobilization upon drying duration to colloid generation from dry pore walls and distribution of colloids in flow paths, which appear to be sensitive to the moisture content of soil after drying and flow path permeability. The results are useful for improving the understanding of colloid mobilization during fluctuating weather conditions.