Stable polyethylene inlay fixation and low polyethylene wear rate in fixed-bearing total knee arthroplasty at five to six years' follow-up.

Aims: Micromotion of the polyethylene (PE) inlay may contribute to backside PE wear in addition to articulate wear of total knee arthroplasty (TKA). Using radiostereometric analysis (RSA) with tantalum beads in the PE inlay, we evaluated PE micromotion and its relationship to PE wear. Methods: A total of 23 patients with a mean age of 83 years (77 to 91), were available from a RSA study on cemented TKA with Maxim tibial components (Zimmer Biomet). PE inlay migration, PE wear, tibial component migration, and the anatomical knee axis were evaluated on weightbearing stereoradiographs. PE inlay wear was measured as the deepest penetration of the femoral component into the PE inlay. Results: At mean six years' follow-up, the PE wear rate was 0.08 mm/year (95% confidence interval 0.06 to 0.09 mm/year). PE inlay external rotation was below the precision limit and did not influence PE wear. Varus knee alignment did not influence PE wear (p = 0.874), but increased tibial component total translation (p = 0.041). Conclusion: The PE inlay was well fixed and there was no relationship between PE stability and PE wear. The PE wear rate was low and similar in the medial and lateral compartments. Varus knee alignment did not influence PE wear.

Evaluation of automated radiostereometric image registration in total knee arthroplasty utilizing a synthetic-based and a CT-based volumetric model.

Radiostereometic analysis (RSA) is an accurate method for rigid body pose (position and orientation) in three-dimensional space. Traditionally, RSA is based on insertion of periprosthetic tantalum markers and manual implant contour selection which limit clinically application. We propose an automated image registration technique utilizing digitally reconstructed radiographs (DRR) of computed tomography (CT) volumetric bone models (autorsa-bone) as a substitute for tantalum markers. Furthermore, an automated synthetic volumetric representation of total knee arthroplasty implant models (autorsa-volume) to improve previous silhouette-projection methods (autorsa-surface). As reference, we investigated the accuracy of implanted tantalum markers (marker) or a conventional manually contour-based method (mbrsa) for the femur and tibia. The data are presented as mean (standard deviation). The autorsa-bone method displayed similar accuracy of -0.013 (0.075) mm compared to the gold standard method (marker) of -0.013 (0.085). The autorsa-volume with 0.034 (0.106) mm did not markedly improve the autorsa-surface with 0.002 (0.129) mm, and none of these reached the mbrsa method of -0.009 (0.094) mm. In conclusion, marker-free RSA is feasible with similar accuracy as gold standard utilizing DRR and CT obtained volumetric bone models. Furthermore, utilizing synthetic generated volumetric implant models could not improve the silhouette-based method. However, with a slight loss of accuracy the autorsa methods provide a feasible automated alternative to the semi-automated method.

Medial congruent polyethylene design show different tibiofemoral kinematics and enhanced congruency compared to a standard symmetrical cruciate retaining design for total knee arthroplasty-an in vivo randomized controlled study of gait using dynamic radiostereometry.

PURPOSE: New total knee arthroplasty implant designs attempt to normalize kinematics patterns that may improve functional performance and patient satisfaction. It was hypothesized that a more medial congruent (MC) anatomic bearing design (1) influences the tibiofemoral kinematics and (2) enhances articular congruency compared to a standard symmetrical cruciate retaining (CR) bearing design. METHODS: In this double-blinded randomized study, 66 patients with knee osteoarthritis were randomly included in two groups: MC (n = 31) and CR (n = 33). Clinical characteristics such as knee ligament lesions and knee osteoarthritis scores were graded on preoperative magnetic resonance imaging and radiography. At the 1-year follow-up, dynamic radiostereometric analysis was used to assess tibiofemoral joint kinematics and articulation congruency. Patient-reported outcome measures, Oxford Knee Score, the Forgotten Joint Score, and the Knee Osteoarthritis Outcome Score, were assessed preoperatively and at the 1-year follow-up. RESULTS: Compared to the CR bearing, the MC bearing displayed an offset with approximately 3 mm greater anterior tibial drawer (p < 0.001) during the entire motion, and up to approximately 3.5 degrees more tibial external rotation (p = 0.004) from mid-swing to the end of the gait cycle at the 1-year follow-up. Furthermore, the congruency area in the joint articulation was larger during approximately 80% of the gait cycle for the MC bearing compared to the CR. The patient-reported outcome measures improved (p < 0.001), but there were no differences between groups. In addition, there were no differences in clinical characteristics and there were no knee revisions or recognized deep infections during follow-up. CONCLUSION: The study demonstrates that the MC-bearing design changes tibiofemoral kinematics and increases the area of congruency towards more native knee kinematics than the CR bearing. In perspective this may contribute to a more stabilized knee motion, restoring the patient's confidence in knee function during daily activities.

Component migration, bone mineral density changes, and bone turnover markers in cementless and cemented total knee arthroplasty: a prospective randomized RSA study in 53 patients with 2-year follow-up.

PURPOSE: Cementless tibial components migrate initially until osseointegration and preserve periprosthetic bone. Cemented tibial components are fixed from surgery but loose periprosthetic bone. Little is known about bone formation and resorption biomarkers in relation to component fixation and bone mineral density (BMD) changes of cementless and cemented total knee arthroplasty. We hypothesize a similar migration of cemented and cementless tibial components between 1- and 2-year follow-up indicating a stable long-term fixation. METHODS: In a prospective patient-blinded randomized study, we compared cementless (n = 27) and cemented (n = 26) tibial components with radiostereometry measured migration (MTPM = Maximum Total Point Motion: point of component that migrates the most) and changes in BMD and biochemical bone turnover markers (BTMs) until 24 months after surgery. RESULTS: The mean MTPM between 12 and 24 months were similar between groups with - 0.06 mm (95% CI - 0.23; 0.11) in the cementless group compared to 0.02 mm (95% CI - 0.07; 0.11) in the cemented group. However, there was a higher proportion of cementless components (16/25) than cemented components (7/24) with continuous migration (MTPM > 0.2 mm) (p = 0.02). In the medial and anterior region below the tibial components, the BMD increased by mean 1.8% and 7.4% for cementless components and decreased by mean 8.6% and 4.2% for cemented components until 24-month follow-up. In both groups, BTMs initially showed increased bone resorption (CTx) and bone formation (P1NP) followed by normalization to pre-operative levels at 6 months post-surgery. CONCLUSION: More cementless components than cemented components showed continues migration which suggest a higher risk of early revision. Bone turnover increased post-surgery in both groups, but did not explain the difference in change in periprosthetic BMD. LEVEL OF EVIDENCE: I.

Two-year fixation and ten-year clinical outcomes of total knee arthroplasty inserted with normal-curing bone cement and slow-curing bone cement: A randomized controlled trial in 54 patients.

BACKGROUND: The normal-curing Refobacin® Bone Cement R (RR) and slow-curing Refobacin® Plus Bone Cement (RP) were introduced after discontinuation of the historically most used bone cement, Refobacin®-Palacos® R, in 2005. The aim of this study was to compare total knee arthroplasty component fixation with the two bone cements. METHODS: 54 patients with primary knee osteoarthritis were randomized to either RR (N = 27) or RP (N = 27) bone cement and followed for two years with radiostereometric analysis of tibial and femoral component migration and dual-energy x-ray absorptiometry measured periprosthetic bone mineral density (BMD). Further, patients were followed up at ten years with clinical outcome scores (OKS and KOOS). RESULTS: At two-years follow-up, tibial total translation was 0.31 mm (95% CI: 0.19 - 0.42) for the RP group and 0.56 mm (95% CI: 0.45 - 0.67) (p < 0.01) for the RR group. There was continuous tibial component migration from one to two years follow-up (MTPM > 0.2 mm) in 13/27 patients from the RR and in 12/26 patients from the RP group. There was no difference between groups in BMD baseline values or changes during follow-up, as well as no correlation between change in BMD and tibial component migration. At ten-years follow-up, the improvement in the clinical outcome scores was similar between groups. There were no prosthesis related complications during the 10-year follow-up. CONCLUSION: At two years, tibial total translation was lower in the RP compared with the RR cement group, but BMD changes were similar. At ten years, no components were revised and clinical outcome scores were similar between groups.

Assessment of knee kinematics with dynamic radiostereometry: Validation of an automated model-based method of analysis using bone models.

Radiostereometic analysis (RSA) is a precise method for the functional assessment of joint kinematics. Traditionally, the method is based on tracking of surgically implanted bone markers and analysis is user intensive. We propose an automated method of analysis based on models generated from computed tomography (CT) scans and digitally reconstructed radiographs. The study investigates method agreement between marker-based RSA and the CT bone model-based RSA method for assessment of knee joint kinematics in an experimental setup. Eight cadaveric specimens were prepared with bone markers and bone volume models were generated from CT-scans. Using a mobile fixture setup, dynamic RSA recordings were obtained during a knee flexion exercise in two unique radiographic setups, uniplanar and biplanar. The method agreement between marker-based and CT bone model-based RSA methods was compared using bias and LoA. Results obtained from uniplanar and biplanar recordings were compared and the influence of radiographic setup was considered for clinical relevance. The automated method had a bias of -0.19 mm and 0.11° and LoA within ±0.42 mm and ±0.33° for knee joint translations and rotations, respectively. The model pose estimation of the tibial bone was more precise than the femoral bone. The radiographic setup had no clinically relevant effect on results. In conclusion, the automated CT bone model-based RSA method had a clinical precision comparable to that of marker-based RSA. The automated method is non-invasive, fast, and clinically applicable for functional assessment of knee kinematics and pathomechanics in patients.

The Effect of Bone Quality on Tibial Component Migration in Medial Cemented Unicompartmental Knee Arthroplasty. A Prospective Cohort Study Using Dual X-Ray Absorptiometry and Radiostereometric Analysis.

BACKGROUND: Periprosthetic bone mineral density (BMD) may influence implant fixation and subsequent loosening. Unicompartmental knee arthroplasty (UKA) restores normal knee kinematics and load distribution to the surrounding bone. We studied the influence of systemic and periprosthetic BMD of the proximal tibia on migration of the tibial component of cemented medial UKA. METHODS: The cohort was dichotomized into a normal BMD group (T-score ≥ -1; n = 37) and a low BMD group (T-score < -1; n = 28) according to World Health Organization criteria. BMD of the proximal tibia and migration of the tibial component were measured with dual X-ray absorptiometry scans and stereoradiographs with 2-year follow-up. RESULTS: Patients with normal systemic BMD had an 11% to15% higher BMD in all regions of interest (ROIs) compared to patients with low systemic BMD throughout follow-up. Over time, a decrease in periprosthetic BMD in ROI 1-3 was seen for both groups. The operated knees and contralateral knees showed a similar reduction in BMD in all ROIs between preoperative and 24 months. Between 12 and 24 months, the normal BMD group migrated (maximal total point motion) 0.03 mm (95% confidence interval, -0.01, 0.08) and the low BMD group migrated 0.02 mm (95% confidence interval, -0.03, 0.07). Migration over time was not influenced by change in periprosthetic BMD. CONCLUSION: Migration of cemented medial tibial UKA was low until 24 months and was neither affected by preoperative systemic BMD nor affected by postoperative change in periprosthetic BMD. This suggests good long-term fixation despite an index difference in proximal tibial BMD.

A prospective study of day of surgery discharge in 368 consecutive patients with unicompartmental knee replacement.

INTRODUCTION: There has been an increased focus on fast-track (FT) programmes and the potential to convert unicompartmental knee replacement (UKR) from short-term admission to outpatient surgery. However, relatively few studies have been presented and with differences in selection criteria and completion rates. The purpose of this study was to describe patient selection and completion rates in a patient group undergoing UKR in two high-volume FT knee surgery clinics. METHODS: All consecutive patients (n = 368) referred to and selected for UKR were screened for eligibility for outpatient surgery with discharge on the day of surgery (DOS). Reasons why the patients were not discharged were recorded in patients not completing the outpatient pathway, and readmissions and complications were recorded until three months post-operatively. RESULTS: Among all referred and screened patients, 69% were considered eligible for outpatient surgery. DOS discharge occurred in 59% of the operated patients and in 37% of all referred and screened patients. Main reasons for why patients were not discharged were active wound drainage and lack of mobilisation due to pain, nausea and vomiting. Two patients were readmitted during the first 24 hours due to wound drainage. One patient had a lung embolus and one patient an acute myocardial infarction during the follow-up period. CONCLUSIONS: This study illustrates that not all patients in a consecutive patient group for UKR were feasible for outpatient surgery. Further studies should focus on optimising pain treatment and reducing post-operative nausea. FUNDING: none. TRIAL REGISTRATION: not relevant.

Implant fracture of the Regenerex® modular metal tibial component: A report of three cases.

BACKGROUND: Implant fractures are a very rare complication in primary total knee replacement (TKR) surgery and with modern implant designs and improved metals these events have nearly been eliminated. In this case series we report three cases of tibial metal baseplate fractures in uncemented Regenerex® TKR. METHODS: Cases originated from a prospective case series of 80 patients operated between 2013 and 2016. Five patients were pilot cases and 75 were participants in a prospective randomized double-blinded clinical trial that evaluated different adjuvant bone anti-resorptive medical therapies. All patients were treated with an uncemented press-fit Regenerex® Porous Titanium Construct tibial tray and matching cemented (Refobacin Bone Cement R) patella and femoral components (hybrid implant). RESULTS: We report three cases of medial side metal baseplate fractures of a modular finned tibial stem. All three baseplate fractures were in male patients. Confirmed failure of the implant occurred after 10, 12 and 23 months, in situ, with a mean follow-up of 15 months (range 10-23). CONCLUSIONS: Based on the current case series we cannot make any causal inferences. Failures may represent a multifactorial process with a cascade of events with implant failure as the result. However, like in most other case reports of metal failures in the literature, the implant fractures in this report were located on the medial side of the tibial component in male patients.

Equal tibial component fixation of a mobile-bearing and fixed-bearing medial unicompartmental knee arthroplasty: a randomized controlled RSA study with 2-year follow-up.

Background and purpose - Differences in stress distribution in a mobile-bearing and fixed-bearing unicompartmental knee arthroplasty (UKA) design might lead to a difference in fixation of the tibial component. We compared tibial component migration of a mobile-bearing (MB) UKA and a fixed-bearing (FB) UKA using radiostereometric analysis.Patients and methods - In a randomized, patient-blinded clinical trial 62 patients received either the MB Oxford UKA or the FB Sigma UKA. The patients were followed for 24 months with radiostereometric analysis. Clinical outcome was assessed with Oxford Knee Score (OKS), RAND-36 and leg extension power.Results - Migration of the tibial components was similar between groups throughout follow-up. At 12 months, MTPM of the tibial component was 0.44 mm (95% CI 0.34-0.55) for the MB group and 0.40 mm (CI 0.31-0.50) for the FB group. Between 12 and 24 months, the tibial components migrated with a median MTPM increase of 0.03 mm (CI -0.02 to 0.08) in the MB group and 0.03 mm (CI -0.02 to 0.07) in the FB group. Continuous migration of the tibial component was found for 1 MB UKA and 2 FB UKAs. Both groups showed similar and clinically relevant improvement in clinical outcome.Interpretation - MB and FB tibial components had similar good fixation and clinical improvement until 2 years. Based on this study, a low 5- to 10-year revision rate can be expected for both implants.

The lateral joint space width can be measured reliably with Telos valgus stress radiography in medial knee osteoarthritis.

OBJECTIVE: To examine the reproducibility of valgus stress radiographs with the Telos stress device for assessment of lateral compartment degenerative changes in patients with medial osteoarthritis of the knee. MATERIALS AND METHODS: A prospective reliability study was performed. Seventy-nine patients (80 knees) were included, and standardized valgus stress radiographs were obtained using the Telos stress device. Osteophytes and joint space narrowing (JSN) were graded using the OARSI (Osteoarthritis Research Society International) classification, and the joint space width (JSW) was measured in millimeters. Reproducibility was determined as intra-and inter-rater reliability and test-retest reliability. Weighted kappa was used to determine the reliability of osteophyte and JSN grading, and the intra-class correlation coefficient for JSW. RESULTS: Grading of osteophytes had an intra- and inter-rater reliability ranging from 0.40 to 0.83 on the medial side and ranging from 0.39 to 0.87 on the lateral side. Grading of medial JSN had an intra- and inter-rater reliability ranging from 0.62 to 0.84, and grading of lateral JSN had an intra- and inter-rater reliability ranging from 0.32 to 0.65. Intra- and inter-rater reliability of JSW ranged from 0.84 to 0.98 on the medial side, and from 0.59 to 0.89 on the lateral side. Test-retest reliability of JSW of the medial and lateral side ranged from 0.69 to 0.92. CONCLUSIONS: Standardized valgus stress radiographs taken with the Telos stress device are a reliable supplement in the assessment of medial OA of the knee. Evaluation of the lateral compartment on valgus stress radiographs is most reliable with measurement of the lateral JSW.

Low implant migration of the SIGMA® medial unicompartmental knee arthroplasty.

PURPOSE: The purpose of this study was to evaluate implant migration of the fixed-bearing Sigma® medial unicompartmental knee arthroplasty (UKA). UKA is a regularly used treatment for patients with medial osteoarthritis (OA) of the knee. UKA has a higher revision rate than total knee arthroplasty. Implant migration can be used as a predictor of implant loosening. METHODS: A prospective radiostereometric cohort study was performed. Forty-five patients with medial OA of the knee were included and received a cemented Sigma® UKA. The patients were followed for 24 months with radiostereometric analysis (RSA) and clinical outcome scores (Oxford knee score). Clinical precision was based on double determinations taken at 4 and 12 months. Tibial implants were classified as stable (difference in MTPM < 0.2 mm between 1 2 and 24 months) or as continuously migrating (difference in MTPM > 0.2 mm between 12 and 24 months). RESULTS: No significant differences in migration were found for the femoral component. For the tibial component, a difference of 0.05 mm was shown for translation on the x-axis between 4 months and 12 (p < 0.01) and between 4 months and 24 months (p < 0.01). A difference of - 0.23 to - 0.50° was shown for rotation around the x-axis (p < 0.01) and a difference of - 0.11° was shown for rotation around the z-axis between 4 and 12 months (p = 0.02). These differences in migration over time were small and fall within the clinical precision of the measurements. Tibial components were divided into a stable group (N = 26) and a continuously migrating group (N = 11), which showed a significant difference in maximal total point motion (MTPM) (p < 0.01). The Oxford knee score improved significantly from poor before surgery (23.2) to good at follow-up (37.5-40.9). CONCLUSIONS: The Sigma® UKA showed low implant migration and good clinical outcomes, suggesting that the Sigma UKA can be used in clinical practice. However, continuous migration was found in 30% of our patients which could indicate a risk of later revision surgery in this group. LEVEL OF EVIDENCE: II.

Methylprednisolone reduces pain and decreases knee swelling in the first 24 h after fast-track unicompartmental knee arthroplasty.

PURPOSE: Unicompartmental knee arthroplasty (UKA) results in less operative trauma and faster patient recovery than after a conventional total knee arthroplasty. Despite an increased focus on multimodal analgesic strategies, there is still a substantial level of patient-reported pain in the early postsurgical period after UKA. The purpose of the study was to evaluate the effect of a single preoperative dose of systemic methylprednisolone on postsurgical pain after fast-track UKA. METHODS: Seventy-two patients in two consecutive series undergoing unilateral UKA were included in a prospective cohort study. The patients (n = 35) in the treatment group received a single preoperative dose of systemic methylprednisolone 125 mg, whereas the control group (n = 37) did not. Outcome measures were postsurgical pain at rest and during walking, consumption of opioids for pain rescue, knee swelling and knee range of motion, and complications. RESULTS: In the first 24 h after surgery, the treatment group had less pain at rest (p < 0.001) and during walking (p < 0.001) and less consumption of opioids (p = 0.01) in comparison with the control group. Furthermore, the treatment group had 2.2 cm less knee swelling (p = 0.02) in the first post-operative day, and better knee extension (p = 0.004), whereas knee flexion was similar (n.s.) between groups. No serious complications were associated with the treatment. CONCLUSION: Addition of a single preoperative dose of 125 mg systemic methylprednisolone to a multimodal analgesic regime significantly reduced postsurgical pain and opioid consumption and decreased knee swelling in the first 24 h after fast-track UKA. LEVEL OF EVIDENCE: Therapeutic study, Level II.

Selection bias in follow-up interviews with individuals attending the emergency department for occupational injuries.

OBJECTIVE: To examine whether supplementary interview participation was comparable for occupationally injured patients attending two hospital emergency departments and to investigate the magnitude of selection bias in relation to sex, age, severity, job tasks and industry risk level. METHODS: Workers aged 18-70 years who contacted the two emergency departments for an acute occupational injury in 2013 were eligible and given a short questionnaire. Following written consent, a semi-structured interview concerning health and transient risk factors was conducted by telephone. The two departments were compared for study recruitment by age and sex. Respondents and non-respondents to the interview were compared for age, sex, injury severity, job tasks and industry risk level. RESULTS: Of 4002 patients attending the two hospitals, 1693 (42%) participated in the interview. One hospital had a markedly higher response rate to the questionnaire, but the proportions of participation in the interview were similar in the two hospitals. Patients aged <30 years were over-represented among non-respondents whereas sex, injury severity, job task and industry risk level were not significantly different between respondents and non-respondents. CONCLUSIONS: Despite a relatively low interview participation rate among injured individuals attending the emergency department, selection bias was limited. This indicates that results regarding injury risk patterns may be more widely generalisable when examining the causality of occupational injuries. However, the study also showed that young injured workers were less likely to participate in follow-up interviews, which is an important factor when interpreting age-related risk of injury.

[Penetrating injury of lower extremity caused by a heavy machine gun cartridge casing]. / Penetrerende underekstremitetslæsion forårsaget af patronhylster fra tungt maskingevær.

Penetrating injuries caused by cartridge casing are rarely described in the literature. This case report presents a 21-year-old male soldier with a lower extremity injury caused by a heavy machine gun cartridge casing. Physical examination revealed an entrance wound proximal and anterior of his right thigh and there were no exit wound identified. A radiograph of the femur showed the cartridge casing to have travelled caudally into the posterior aspect of the knee. There were no associated fractures or neurovascular injuries. The patient underwent surgical wound debridement and removal of the foreign body and was discharged fully recovered after three days.

[Pyomyositis caused by Streptococcus pneumoniae in a previously healthy 20-year-old man]. / Pyomyositis forårsaget af Streptococcus pneumoniae hos tidligere rask 20-årig.

Pyomyositis is a bacterial infection of the skeletal muscle usually caused by Staphylococcus aureus. This case report presents a 20-year-old man with pyomyositis caused by Streptococcus pneumoniae. Pyomyositis is a rare but potentially critical disease, and early diagnosis, drainage and use of appropriate antibiotic therapy are essential to reduce morbidity and mortality. However, early diagnosis of pyomyositis can be challenging as initial symptoms may be vague, but the condition should be suspected in patients with acute onset of severe, localised muscle pain and fever.

Symptomatic knee disorders in floor layers and graphic designers. A cross-sectional study.

BACKGROUND: Previous studies have described an increased risk of developing tibio-femoral osteoarthritis (TF OA), meniscal tears and bursitis among those with a trade as floor layers. The purpose of this study was to analyse symptomatic knee disorders among floor layers that were highly exposed to kneeling work tasks compared to graphic designers without knee-demanding work tasks. METHODS: Data on the Knee injury and Osteoarthritis Outcome Score (KOOS) were collected by questionnaires. In total 134 floor layers and 120 graphic designers had a bilateral radiographic knee examination to detect TF OA and patella-femoral (PF) OA. A random sample of 92 floor layers and 49 graphic designers had Magnetic Resonance Imaging (MRI) of both knees to examine meniscal tears. Means of the subscales of KOOS were compared by analysis of variance. The risk ratio of symptomatic knee disorders defined as a combination of radiological detected knee OA or MRI-detected meniscal tears combined with a low KOOS score was estimated by logistic regression in floor layers with 95% confidence interval (CI) and adjusted for age, body mass index, traumas, and knee-straining sports activities. Symptomatic knee OA or meniscal tears were defined as a combination of low KOOS-scores and radiographic or MRI pathology. RESULTS: Symptomatic TF and medial meniscal tears were found in floor layers compared to graphic designers with odds ratios 2.6 (95%CI 0.99-6.9) and 2.04 (95% CI 0.77-5.5), respectively. There were no differences in PF OA. Floor layers scored significantly lower on all KOOS subscales compared to graphic designers. Significantly lower scores on the KOOS subscales were also found for radiographic TF and PF OA regardless of trade but not for meniscal tears. CONCLUSIONS: The study showed an overall increased risk of developing symptomatic TF OA in a group of floor layers with a substantial amount of kneeling work positions. Prevention would be appropriate to reduce the proportion of kneeling postures e.g. by working with tools used from a standing working position.

MR Imaging of Intra- and Periarticular Cyst-Like Lesions of the Knee Joint in Workers with Occupational Kneeling.

Objective. To determine the risk of intra- and periarticular cyst-like lesions of the knee joint in occupational kneeling. Methods. Magnetic resonance imaging of both knees (n = 282) was conducted in 92 male floor layers and 49 male graphic designers (referents), with a mean age of 55.6 years (range 42-70 years). The prevalence of cyst-like lesions was computed among floor layers and graphic designers, respectively, and associations with occupation summarized by odds ratio (OR) with 95% confidence intervals (CIs). Using logistic regression, models were adjusted for age, body mass index, knee injuries, and knee-straining sports. Results. Floor layers had a significantly higher prevalence of cyst-like lesions in the posterior part of the knee joint compared to graphic designers (OR 2.70, 95% CI 1.50-4.84). Floor layers also had a higher prevalence of fluid collections in the popliteus tendon recess (OR 2.17, 95% CI 0.99-4.77) and large cystic lesions of the popliteus muscle (OR 3.83, 95% CI 0.78-18.89). The prevalence of cystic lesions in the anterior part of the knee joint was low among floor layers (8.7%) and there was no significant difference between the two trade groups (P = 0.34). Conclusions. Occupational kneeling increases the risk of cyst-like lesions in the posterior part of the knee joint.

Relationship between years in the trade and the development of radiographic knee osteoarthritis and MRI-detected meniscal tears and bursitis in floor layers. A cross-sectional study of a historical cohort.

OBJECTIVES: An increased risk of developing knee disorders including radiographic knee osteoarthritis (OA) have been shown among workers with kneeling working demands. There may also be a dose-related association between duration of employment in occupations with kneeling work and development of radiographic knee OA and magnetic resonance imaging (MRI)-detected meniscal tears and bursitis. DESIGN: A cross-sectional study of a historical cohort. SETTING: Members of the trade unions for floor layers and graphic designers in Denmark. PARTICIPANTS: 92 male floor layers and 49 graphic designers aged 36-70 years were randomly selected among participants from a clinical and radiographic study of 156 floor layers and 152 graphic designers. OUTCOME MEASURES: Radiographic tibiofemoral (TF) and patellofemoral (PF) knee-OA and MRI-detected meniscal tears and bursitis. Results were adjusted for age, earlier knee traumas, sports activities and body mass index in logistic regression models. Association between TF OA and years in the floor-laying trade was graphically examined by a restricted cubic spline with four knots. RESULTS: Increase in number of years with exposure to kneeling work is associated with radiographic TF knee OA with ORs 0.7, 95% CI 0.07 to 4.42; OR 1.89, 95% CI 0.29 to 12.3; OR 4.82, 95% CI 1.38 to 17 for <20 years, 20-30 years and >30 years of kneeling work, respectively. MRI-verified medial meniscal tears was increased among subjects with kneeling work with OR 1.96, 95% CI 0.79 to 4.88 to OR 4.73, 95% CI 1.16 to 19.4 but was not associated with duration of employment. Periarticular bursitis was increased in subjects with <20 years of kneeling working activity. Lateral meniscal tears and PF knee OA were not associated with duration of kneeling working activity or with kneeling work in general. CONCLUSIONS: The findings suggest a dose-response relationship for radiographic TF knee OA in floor layers with a significant amount of kneeling work and an increase of MRI-verified medial meniscal tears among workers with kneeling work.

[Toe tourniquet syndrome in three month-old infant]. / Tåtourniquetsyndrom hos barn på tre måneder.

Toe tourniquet syndrome is a rare condition in which a hair or thread becomes tightly wrapped around an appendage, which causes ischaemic strangulation. We present a three month-old infant with strangulation of one toe to direct attention to this condition. Prompt recognition and complete removal of all fibres is necessary in order to prevent complications. The condition can easily be prevented by simple measures. Consequently, it is important to have the condition in mind in infants who cry for no obvious reason, and in infants presenting with oedema on fingers, toes or genitalia.