Development and validation of synchronous spectrofluorimetric method for the simultaneous determination of duvelisib and moxifloxacin: greenness metric assessment and application to a pharmacokinetic study in rats.

Duvelisib (DUV) is a potent anticancer drug whereas Moxifloxacin (MOX) is an antimicrobial drug with anti-proliferative potency against cancerous cells, which is empirically administered in cancer treatment. DUV and MOX combination is commonly prescribed to combat infections in patients while they are under chemotherapy treatment. This study describes, for the first time, the development of a simple and green synchronous spectrofluorimetric (SSF) method for the simultaneous estimation of DUV and MOX in plasma. DUV and MOX were quantified at 273 and 362 nm, respectively without interference between each other at Δλof 120 nm. The experimental variables influencing fluorescence intensities were thoroughly investigated and the optimum conditions were established. At pH 3.5, the optimum synchronous fluorescence intensity (SFI) was achieved in water solvent by using sodium acetate buffer solution. Calibration curves for DUV and MOX, correlating the SFI with the corresponding drug concentration, were linear in the range of 50-1000 ng mL-1for both drugs, with good correlation coefficients. The method was extremely sensitive, with limits of detection of 24 and 22 ng mL-1, and limits of quantitation of 40 and 45 ngmL-1for DUV and MOX, respectively. The SSF method was validated according to the Food and Drug Administration (FDA) guidelines for validation of analytical procedures, and the validation parameters were acceptable. The proposed SSF method was applied to the pharmacokinetic and bioavailability studies in rats' plasma after single concurrent oral administration of both drugs. The results of the study revealed that caution should be taken with DUV dose when concurrently administered with MOX. The greenness of SSF method was assessed by three different metric tools namely Analytical Eco-scale, Green Analytical Procedure Index, and Analytical Greenness Calculator. The results confirmed that SSF method is an eco-friendly and green analytical approach. In conclusion, the proposed SSF method is a valuable tool for pharmacokinetic/bioavailability studies and therapeutic drug monitoring of simultaneously administered DUV and MOX.

Classical versus chemometrics tools for spectrophotometric determination of fluocinolone acetonide, ciprofloxacin HCl and ciprofloxacin impurity-A in their ternary mixture.

Green, simple, accurate and robust univariate and chemometrics assisted UV spectrophotometric approaches have been adopted and validated for concurrent quantification of fluocinolone acetonide (FLU), ciprofloxacin HCl (CIP) together with ciprofloxacin impurity-A (CIP imp-A) in their ternary mixture. Double-divisor ratio spectra derivative (DDRD) method has been used for determination of FLU. On the other hand, the first (D1) and second (D2) derivative approaches have been applied for the quantification of CIP and CIP imp-A, respectively. For the ratio difference (RD), derivative ratio (DR), and mean centering of ratio spectra (MC) methods, CIP and its impurity A have been simultaneously determined. The acquired calibration plots were linear over the concentration range of 0.6-20.0 µg/mL, 1.0-40.0 µg/mL and 1.0-40.0 µg/mL for fluocinolone acetonide, ciprofloxacin HCl, and ciprofloxacin impurity-A, respectively. The chemometrics methods namely; partial least squares (PLS) and artificial neural networks (ANN) were used for the concurrent determination of the three adopted components via using twenty-five mixtures as calibration set and fifteen mixtures as validation one. The investigated approaches were validated in accordance with International Council for Harmonisation (ICH) guidelines, and statistically compared with the official ones. The proposed methods were acceptably applied to the examination of FLU and CIP in their pure powders and pharmaceutical ear drops.

Two fabricated carbon paste electrodes for novel potentiometric determination of probenecid in dosage form and human plasma.

Solid contact ion selective electrodes are extensively utilized owing to their marvelous performance over traditional liquid contact ones. The main drawback of those solid contact electrodes is aqueous layer formation which affects their constancy. Herein and to overcome this common drawback, a carbon paste electrode containing poly(3,4-ethylenedioxythiophene) was constructed and used for determination of probenecid at variant pH values. This modification decreased the potential drift down to 0.8 mV/h and improved its stability over 30 days. A Nernstian slope of - 57.8 mV/decade associated with a linear range of 1.0 × 10-6-1.0 × 10-2 mol/L was obtained. The modified carbon paste electrode successfully detected up to 8.0 × 10-7 mol/L probenecid. Results of this modified carbon paste electrode were also compared to unmodified one.

Eco-friendly resolution of spectrally overlapping signals of a combined triple-action over-the-counter pharmaceutical formulation for symptomatic management of COVID-19 pandemic: application to content uniformity testing.

Currently, all researchers are concentrating their efforts on countering the COVID-19 pandemic. The majority of patients are managed at home, according to recent statistics. An OTC triple action combination comprising paracetamol (PAR), aspirin (ASP), and diphenhydramine (DIPH) is commonly given for pain relief, fever control, and as a night-time sleep aid. This combination is currently recommended for COVID-19 patients as part of symptomatic treatment and management. In this work, three smart, simple, accurate, eco-friendly, and cost-effective spectrophotometric methods are developed for simultaneous determination of PAR, ASP, and DIPH in their combined over-the-counter caplet dosage form without any prior separation steps. The first method is the first derivative spectrophotometry (D1) which determined PAR at 259.7 nm. The second one is the dual-wavelength in ratio spectra (DWRS) for determination of ASP at 214.1 and 220.1 nm after using 10.0 µg/mL of PAR as a divisor, where PAR was a constant, and the wavelengths difference equal to zero for DIPH. The third method is the double divisor-ratio difference spectrophotometric one (DD-RD) which was based on using the sum of 15.0 µg/mL of each of PAR and ASP as a double divisor, and the difference in amplitudes was measured at two wavelengths ∆P(214.5-226.0) for determination of DIPH. The developed methods have been validated as per ICH guidelines. Furthermore, the three suggested methods were employed successfully to assay marketed pharmaceutical formulation and to investigate the content uniformity of the dosage units in accordance with the United States Pharmacopeia's guidelines. Finally, the greenness profile of the proposed methods was assessed and compared with the reported method using the analytical eco-scale system, national environmental method index (NEMI), green analytical procedure index (GAPI), and analytical greenness (AGREE) metric. The results from the proposed methods statistically agreed with those obtained by the reported one, with no significant differences in accuracy and precision.

Sustainable liquid chromatographic determination and purity assessment of a possible add-on triple-action over-the-counter pharmaceutical combination in COVID-19.

Nowadays, all researchers are focused on combating the pandemic COVID-19. According to recent statistics, most patients are managed at home. An over-the-counter (OTC) triple action formula containing paracetamol (PAR), aspirin (ASP), and diphenhydramine (DIPH) is widely prescribed for pain, fever and as night-time sleep aid. For COVID-19 patients, this combination is now suggested as part of symptomatic therapy and prophylaxis. In this work, two simple liquid chromatographic approaches were designed for simultaneous determination of PAR, ASP, and DIPH in Excedrin® PM caplets, beside three specified official toxic impurities, namely, p-aminophenol, p-nitrophenol, and salicylic acid. The first method comprised high-performance thin-layer chromatographic separation coupled with densitometric quantification, on silica gel HPTLC 60 F254 aluminium sheets as the stationary phase, ethyl acetate-methanol-aqueous ammonium hydroxide (10.0: 2.0: 0.1, by volume) as the developing system and scanning was performed at 210.0 nm. The second one is a high-performance liquid chromatography coupled with diode array detector. Successful separation of the six components was performed on XTerra C18 column with isocratic elution of mobile phase 0.1% triethylamine acidified water: methanol (70:30, v/v) adjusted with o-phosphoric acid to pH 3.0 and methanol (90:10, v/v) with flow rate programming and detection at 210.0 nm. Validation of the proposed methods was performed according to ICH guidelines. Both methods were successfully used for quality control of the cited drugs in their marketed formulation. Moreover, the in-vitro release study was monitored using the proposed HPLC-DAD method. The greenness profile of the proposed methods was assessed and comparatively evaluated through various assessment tools, specifically; the analytical eco-scale system, national environmental method index (NEMI), green analytical procedure index (GAPI) and analytical greenness (AGREE) metric.

Smart spectrophotometric methods for stability assessment of two co-formulated antigout drugs.

Simple, sensitive and accurate stability indicating spectrophotometric methods have been developed for the simultaneous determination of probenecid, colchicine as well as colchicine degradation product in their ternary mixture. Probenecid was firstly assayed using the double divisor ratio spectra derivative method. On the other hand, three spectrophotometric methods, namely: ratio difference, derivative ratio and mean centering of ratio spectra, have been suggested for the simultaneous quantification of colchicine and its degradation product. The obtained calibration curves were linear at 2.5-30.0 µg/mL, 0.5-25.0 µg/mL and 1.0-13.0 µg/mL for probenecid, colchicine and colchicine degradation product, respectively. The investigated methods were validated in accordance with the International Council for Harmonisation guidelines and were effectively used for quantification of probenecid and colchicine in their bulk powders and combined pharmaceutical dosage form.

Two Validated Chromatographic Methods for Determination of Ciprofloxacin HCl, One of its Specified Impurities and Fluocinolone Acetonide in Newly Approved Otic Solution.

Two sensitive, selective and precise chromatographic methods have been established for concomitant quantification of ciprofloxacin HCl (CIP), fluocinolone acetonide (FLU) along with ciprofloxacin impurity A (CIP-imp A). The first method was thin-layer chromatography (TLC-densitometry) where separation was accomplished using TLC silica plates 60 G.F254 as a stationary phase and chloroform-methanol-33%ammonia (4.6:4.4:1, by volume) as a developing system. The obtained plates were scanned at 260 nm over concentration ranges of 1.0-40.0, 0.6-20.0 and 1.0-40.0 µg band-1 for CIP, FLU and CIP-imp A, respectively. The second method was based on high-performance liquid chromatography using a Zorbax ODS column (5 µm, 150 × 4.6 mm i.d.) where adequate separation was achieved through a mobile phase composed of phosphate buffer pH 3.6-acetonitrile (45:55, v/v) at flow rate 1.0 mL min-1 with ultraviolet detection at 254 nm. Linear regressions were obtained in the range of 1.0-40.0 µg mL-1 for CIP, 0.6-20.0 µg mL-1 for FLU and 1.0-40.0 µg mL-1 for CIP-imp A. The suggested methods were validated in compliance with the International Conference on Harmonization guidelines and were successfully applied for determination of CIP and FLU in bulk powder and newly marketed otic solution.

Stability-Indicating Chromatographic Methods for the Simultaneous Determination of Probenecid and Colchicine in Their Combined Tablet.

Two stability-indicating chromatographic methods have been established and validated for concurrent determination of probenecid (PRO), colchicine (COL) along with the degradation product of colchicine (COL deg). PRO and COL were exposed to a stress stability study, which includes acidic, alkaline, oxidative, photolytic and thermal degradations. Chromatographic methods included the use of thin layer chromatography (TLC-densitometry) and high performance liquid chromatography (HPLC). In the first method, separation was achieved by using aluminum TLC plates that were precoated with silica gel G.F254 as the stationary phase and ethyl acetate-methanol-33%ammonia (8:1:1, by volume) as a mobile phase. The obtained chromatograms were scanned at 254 nm. The second method was based on HPLC using a RP- C18 column with isocratic elution. Good separation was obtained through a mobile phase comprised of phosphate buffer pH 5-acetonitrile (70:30, v/v) at a flow rate of 1.0 mL min-1 and ultraviolet detection at 254 nm. Different parameters affecting efficiency of the two methods were studied accurately for optimum separation of the three cited components. The suggested methods were validated according to the International Conference on Harmonization (ICH) guidelines and were applied for bulk powder and commercial tablets.

Greenness profile assessment of selective liquid chromatographic methods for determination of a quaternary antimigraine combination along with three of their related official impurities.

Two selective, sensitive and environmentally safe LC methods were developed and validated for determination of paracetamol, caffeine, ergotamine tartrate and metoclopramide in coformulated antimigraine tablets along with p-aminophenol, p-nitrophenol and theophylline as officially specified impurities. The first is based on high-performance thin-layer chromatography (HPTLC) coupled with densitometric quantitation. Separation was achieved on HPTLC silica gel 60 F254 plates as stationary phase using ethyl acetate:aqueous ammonium hydroxide solution:glacial acetic acid (10.0:0.4:0.1, by volume) as a developing system followed by scanning of the separated bands at 210.0 nm. The subsequent method depends on HPLC with diode array detection. The LC separation was accomplished on a Scharlau C18 (250 × 4.6 mm, 5 µm) column using a mixture of 20.0 mm sodium dihydrogen phosphate, pH 3.0, adjusted with o-phosphoric acid and methanol, at a flow rate of 1.3 mL/min in a gradient elution program. The separated peaks were detected at 210.0 nm. The proposed methods have been validated and proven to meet the requirements outlined in the International Council for Harmonisation (ICH) guidelines. The greenness profile evaluation was carried out using three tools, namely, the National Environmental Method Index, the Analytical EcoScale and the Green Analytical Procedure Index tool, and a comparative study was then conducted. Successful application of the developed methods for determination of the cited quaternary mixture in Metograine tablets confirms their suitability regarding the analytical performance and ecological impact in quality control assay and impurity profiling purposes.

Validated green high-performance liquid chromatographic methods for the determination of coformulated pharmaceuticals: a comparison with reported conventional methods.

The introduction of sustainable development concepts to analytical laboratories has recently gained interest, however, most conventional high-performance liquid chromatography methods do not consider either the effect of the used chemicals or the amount of produced waste on the environment. The aim of this work was to prove that conventional methods can be replaced by greener ones with the same analytical parameters. The suggested methods were designed so that they neither use nor produce harmful chemicals and produce minimum waste to be used in routine analysis without harming the environment. This was achieved by using green mobile phases and short run times. Four mixtures were chosen as models for this study; clidinium bromide/chlordiazepoxide hydrochloride, phenobarbitone/pipenzolate bromide, mebeverine hydrochloride/sulpiride, and chlorphenoxamine hydrochloride/caffeine/8-chlorotheophylline either in their bulk powder or in their dosage forms. The methods were validated with respect to linearity, precision, accuracy, system suitability, and robustness. The developed methods were compared to the reported conventional high-performance liquid chromatography methods regarding their greenness profile. The suggested methods were found to be greener and more time- and solvent-saving than the reported ones; hence they can be used for routine analysis of the studied mixtures without harming the environment.