Plastic waste recycling: existing Indian scenario and future opportunities.

This review article aims to suggest recycling technological options in India and illustrates plastic recycling clusters and reprocessing infrastructure for plastic waste (PW) recycling in India. The study shows that a majority of states in India are engaged in recycling, road construction, and co-processing in cement kilns while reprocessing capabilities among the reprocessors are highest for polypropylene (PP) and polyethylene (PE) polymer materials. This review suggests that there are key opportunities for mechanical recycling, chemical recycling, waste-to-energy approaches, and bio-based polymers as an alternative to deliver impact to India's PW problem. On the other hand, overall, polyurethane, nylon, and polyethylene terephthalate appear most competitive for chemical recycling. Compared to conventional fossil fuel energy sources, polyethylene (PE), polypropylene (PP), and polystyrene are the three main polymers with higher calorific values suitable for energy production. Also, multi-sensor-based artificial intelligence and blockchain technology and digitization for PW recycling can prove to be the future for India in the waste flow chain and its management. Overall, for a circular plastic economy in India, there is a necessity for a technology-enabled accountable quality-assured collaborative supply chain of virgin and recycled material. Supplementary Information: The online version contains supplementary material available at 10.1007/s13762-022-04079-x.

Extraordinary water adsorption characteristics of graphene oxide.

The laminated structure of graphene oxide (GO) confers unique interactions with water molecules which may be utilised in a range of applications that require materials with tuneable hygroscopic properties. The precise role of the expandable interlayer spacing and functional groups in GO laminates has not completely been understood to date. Herein, we report the experimental and theoretical investigations on the adsorption and desorption behaviour of water in GO laminates as a function of relative pressure. We observed that GO imparts high water uptake capacity of up to 0.58 gram of water per gram of GO (g g-1), which is significantly higher than silica gel as a conventional desiccant material. More interestingly, the adsorption and desorption kinetics of GO is five times higher than silica gel. The observed extraordinary adsorption/desorption rate can be attributed to the high capillary pressure in GO laminates as well as micro meter sized tunnel-like wrinkles located at the surface.

High temperature investigations on optimising the recovery of copper from waste printed circuit boards.

High temperature pyrolysis investigations were carried out on waste printed circuit boards (PCBs) in the temperature range 800-1000°C under inert conditions, with an aim to determine optimal operating conditions for the recovery of copper. Pyrolysis residues were characterized using ICP-OES analysis, SEM/EDS and XRD investigations. Copper foils were successfully recovered after pyrolysis at 800°C for 10-20 min; the levels of Pb and Sn present were found to be quite low and these were generally present near the foil edges. The relative proportions of Pb and Sn became progressively higher at longer heating times due to enhanced diffusion of these molten metals in solid copper. While a similar behaviour was observed at 900°C, the pyrolysis at 1000°C resulted in copper forming Cu-Sn-Pb alloys; copper foils could no longer be recovered. Optimal conditions were identified for the direct recovery of copper from waste PCBs with minimal processing. This approach is expected to make significant contributions towards enhancing material recovery, process efficiency and the environmental sustainability of recycling e-waste. Pyrolysis at lower temperatures, short heating times, coupled with reductions in process steps are expected to significantly reduce energy consumption and pollution associated with the handling and processing of waste PCBs.

A novel approach for reducing toxic emissions during high temperature processing of electronic waste.

A novel approach is presented to capture some of the potentially toxic elements (PTEs), other particulates and emissions during the heat treatment of e-waste using alumina adsorbents. Waste PCBs from mobile phones were mechanically crushed to sizes less than 1mm; their thermal degradation was investigated using thermo-gravimetric analysis. Observed weight loss was attributed to the degradation of polymers and the vaporization of organic constituents and volatile metals. The sample assembly containing PCB powder and adsorbent was heat treated at 600°C for times ranging between 10 and 30min with air, nitrogen and argon as carrier gases. Weight gains up to ∼17% were recorded in the adsorbent thereby indicating the capture of significant amounts of particulates. The highest level of adsorption was observed in N2 atmosphere for small particle sizes of alumina. SEM/EDS results on the adsorbent indicated the presence of Cu, Pb, Si, Mg and C. These studies were supplemented with ICP-OES analysis to determine the extent of various species captured as a function of operating parameters. This innovative, low-cost approach has the potential for utilization in the informal sector and/or developing countries, and could play a significant role in reducing toxic emissions from e-waste processing towards environmentally safe limits.

On the mechanism of gas adsorption for pristine, defective and functionalized graphene.

Defects are no longer deemed an adverse aspect of graphene. Contrarily, they can pave ways of extending the applicability of graphene. Herein, we discuss the effects of three types of defects in graphene including carbon deficiency, adatom (single Fe) dopants and the introduction of functional groups (carbonyl, ether group) on the NO2 gas adsorption via density functional theory methods. We have observed that introducing Fe on graphene can enhance the NO2 adsorption process. Adsorption energy calculations suggest that the enhancement in NO2 adsorption is more profound for Fe-doped mono- and tetra-vacant graphene than that for Fe doped bi- and tri-vacant graphene, which is favourable for NO2 gas capture applications. The unsaturated carbons in defected graphene as well as the oxygenated functional groups are very active to attract NO2 molecules. However, though the gas binding strength was not as high as the that found in the Fe-doped graphene structure, the relatively low NO2 gas adsorption energy is suitable for the practical gas sensors both for gas sensitivity and the sensor recovery rate factor. This theoretical study can potentially be useful for developing adsorption-based applications of graphene.

Stability of retained austenite in high carbon steel under compressive stress: an investigation from macro to nano scale.

Although high carbon martensitic steels are well known for their industrial utility in high abrasion and extreme operating environments, due to their hardness and strength, the compressive stability of their retained austenite, and the implications for the steels' performance and potential uses, is not well understood. This article describes the first investigation at both the macro and nano scale of the compressive stability of retained austenite in high carbon martensitic steel. Using a combination of standard compression testing, X-ray diffraction, optical microstructure, electron backscattering diffraction imaging, electron probe micro-analysis, nano-indentation and micro-indentation measurements, we determined the mechanical stability of retained austenite and martensite in high carbon steel under compressive stress and identified the phase transformation mechanism, from the macro to the nano level. We found at the early stage of plastic deformation hexagonal close-packed (HCP) martensite formation dominates, while higher compression loads trigger body-centred tetragonal (BCT) martensite formation. The combination of this phase transformation and strain hardening led to an increase in the hardness of high carbon steel of around 30%. This comprehensive characterisation of stress induced phase transformation could enable the precise control of the microstructures of high carbon martensitic steels, and hence their properties.

Concentration of precious metals during their recovery from electronic waste.

The rapid growth of electronic devices, their subsequent obsolescence and disposal has resulted in electronic waste (e-waste) being one of the fastest increasing waste streams worldwide. The main component of e-waste is printed circuit boards (PCBs), which contain substantial quantities of precious metals in concentrations significantly higher than those typically found in corresponding ores. The high value and limited reserves of minerals containing these metals makes urban mining of precious metals very attractive. This article is focused on the concentration and recovery of precious metals during pyro-metallurgical recycling of waste PCBs. High temperature pyrolysis was carried out for ten minutes in a horizontal tube furnace in the temperature range 800-1350°C under Argon gas flowing at 1L/min. These temperatures were chosen to lie below and above the melting point (1084.87°C) of copper, the main metal in PCBs, to study the influence of its physical state on the recovery of precious metals. The heat treatment of waste PCBs resulted in two different types of solid products, namely a carbonaceous non-metallic fraction (NMFs) and metallic products, composed of copper rich foils and/or droplets and tin-lead rich droplets and some wires. Significant proportions of Ag, Au, Pd and Pt were found concentrated within two types of metallic phases, with very limited quantities retained by the NMFs. This process was successful in concentrating several precious metals such as Ag, Au, Pd and Pt in a small volume fraction, and reduced volumes for further processing/refinement by up to 75%. The amounts of secondary wastes produced were also minimised to a great extent. The generation of precious metals rich metallic phases demonstrates high temperature pyrolysis as a viable approach towards the recovery of precious metals from e-waste.

Generation of copper rich metallic phases from waste printed circuit boards.

The rapid consumption and obsolescence of electronics have resulted in e-waste being one of the fastest growing waste streams worldwide. Printed circuit boards (PCBs) are among the most complex e-waste, containing significant quantities of hazardous and toxic materials leading to high levels of pollution if landfilled or processed inappropriately. However, PCBs are also an important resource of metals including copper, tin, lead and precious metals; their recycling is appealing especially as the concentration of these metals in PCBs is considerably higher than in their ores. This article is focused on a novel approach to recover copper rich phases from waste PCBs. Crushed PCBs were heat treated at 1150°C under argon gas flowing at 1L/min into a horizontal tube furnace. Samples were placed into an alumina crucible and positioned in the cold zone of the furnace for 5 min to avoid thermal shock, and then pushed into the hot zone, with specimens exposed to high temperatures for 10 and 20 min. After treatment, residues were pulled back to the cold zone and kept there for 5 min to avoid thermal cracking and re-oxidation. This process resulted in the generation of a metallic phase in the form of droplets and a carbonaceous residue. The metallic phase was formed of copper-rich red droplets and tin-rich white droplets along with the presence of several precious metals. The carbonaceous residue was found to consist of slag and ∼30% carbon. The process conditions led to the segregation of hazardous lead and tin clusters in the metallic phase. The heat treatment temperature was chosen to be above the melting point of copper; molten copper helped to concentrate metallic constituents and their separation from the carbonaceous residue and the slag. Inert atmosphere prevented the re-oxidation of metals and the loss of carbon in the gaseous fraction. Recycling e-waste is expected to lead to enhanced metal recovery, conserving natural resources and providing an environmentally sustainable solution to the management of waste products.