Pseudo-orthogonal frequency coded wireless SAW RFID temperature sensor tags.

SAW sensors are ideal for various wireless, passive multi-sensor applications because they are small, rugged, radiation hard, and offer a wide range of material choices for operation over broad temperature ranges. The readable distance of a tag in a multi-sensor environment is dependent on the insertion loss of the device and the processing gain of the system. Single-frequency code division multiple access (CDMA) tags that are used in high-volume commercial applications must have universal coding schemes and large numbers of codes. The use of a large number of bits at the common center frequency to achieve sufficient code diversity in CDMA tags necessitates reflector banks with >30 dB loss. Orthogonal frequency coding is a spread-spectrum approach that employs frequency and time diversity to achieve enhanced tag properties. The use of orthogonal frequency coded (OFC) SAW tags reduces adjacent reflector interactions for low insertion loss, increased range, complex coding, and system processing gain. This work describes a SAW tag-sensor platform that reduces device loss by implementing long reflector banks with optimized spectral coding. This new pseudo-OFC (POFC) coding is defined and contrasted with the previously defined OFC coding scheme. Auto- and cross-correlation properties of the chips and their relation to reflectivity per strip and reflector length are discussed. Results at 250 MHz of 8-chip OFC and POFC SAW tags will be compared. The key parameters of insertion loss, cross-correlation, and autocorrelation of the two types of frequency-coded tags will be analyzed, contrasted, and discussed. It is shown that coded reflector banks can be achieved with near-zero loss and still maintain good coding properties. Experimental results and results predicted by the coupling of modes model are presented for varying reflector designs and codes. A prototype 915-MHz POFC sensor tag is used as a wireless temperature sensor and the results are shown.

Improved reflectivity and velocity model for aluminum gratings on YZ LiNbO3.

Lithium niobate has recently been used for SAW tags and temperature sensors because of its high coupling coefficient and high reflectivity. To increase the device operating frequency for a given electrode line resolution, harmonic operation of the reflector is a very attractive option. When used in conjunction with harmonically operated transducers, the device operating frequency can be increased for a given photolithographic line width resolution. To design and accurately predict the behavior of these devices, it is necessary to model the electrode reflectivity and velocity for both fundamental and second-harmonic operation. The coupling of modes (COM) model has been used to model these devices, however the COM model uses empirically determined coefficients to model reflectivity. In this paper, the reflectivity and velocity of aluminum electrodes is extracted experimentally for fundamental and second-harmonic operation versus metalization ratios ranging from 0.2 to 0.9 and versus normalized metal thickness ranging from 0.4% to 4%. A least-squares fit is then performed on the data using physical terms in the transmission line model to yield equations that can be used in the COM model to predict device behavior over varying metallization ratios and normalized metal thicknesses. Orthogonal frequency-coded (OFC) SAW tags were designed and fabricated and experimentally obtained data are compared with the COM modeled responses for the tags at fundamental and second-harmonic operation to verify the predictions.

Orthogonal frequency coded filters for use in ultra-wideband communication systems.

The use of ultra-short pulses, producing very wide bandwidths and low spectral power density, are the widely accepted approach for ultra-wideband (UWB) communication systems. This approach is simple and can be implemented with current digital signal processing technologies. However, surface acoustic wave (SAW) devices have the capability of producing complex signals with wide bandwidths and relatively high frequency operation. This approach, using SAW based correlators, eliminates many of the costly components that are needed in the IF block in the transmitter and receiver, and reduces many of the signal processing requirements. This work presents the development of SAW correlators using orthogonal frequency coding (OFC) for use in UWB spread spectrum communication systems. OFC and pseudonoise (PN) coding provide a means for UWB spreading of data. The use of OFC spectrally spreads a PN sequence beyond that of code division multiple access (CDMA) because of the increased bandwidth providing an improvement in processing gain. The transceiver approach is still very similar to that of a CDMA but provides greater code diversity. Experimental results of a SAW filter designed with OFC transducers are presented. The SAW correlation filter was designed using seven contiguous chip frequencies within the transducer. SAW correlators with a 29% fractional bandwidth were fabricated on lithium niobate (LiNbO3) having a center frequency of 250 MHz. A coupling-of-modes (COM) model is used to predict the SAW filter response experimentally and is compared to the measured data. Good correlation between the predicted COM responses and the measured device data is obtained. Discussion of the design, analysis, and measurements are presented. The experimental matched filter results are shown for the OFC device and are compared to the ideal correlation. The results demonstrate the OFC SAW device concept for UWB communication transceivers.

SAW parameters on Y-cut langasite structured materials.

This paper presents results and investigations of several new, man-made piezoelectric single crystal, Czochralski-grown substrate materials for surface acoustic waves (SAW) applications. These materials, langanite (LGN), langatate (LGT), Sr3TaGa3Si2O14 (STGS), Sr3NbGa3Si2O14 (SNGS), Ca3TaGa3Si2O14 (CTGS), and Ca3NbGa3Si2O14 (CNGS), have the same structure as langasite (LGS) and are of the same crystal class as quartz. These compounds are denser than quartz, resulting in lower phase velocities. They also have higher coupling. Unlike quartz and lithium niobate, there is no degradation of material properties below the material melting points resulting in the possibility of extreme high-temperature operation (> 1000 degrees C). This paper gives a summary of extracted SAW material parameters for various propagation angles on Y-cut substrates of the six materials. Parameters included are electromechanical coupling, phase velocity, transducer capacitance, metal strip reflectivity, and temperature coefficient of frequency. Using previously published fundamental material constants, extracted parameters are compared with predictions for LGT and LGN. In addition, power flow angle and fractional frequency curvature data are reported for propagation angles on CTGS and CNGS Y-cut substrates that exhibit temperature compensation near room temperature. Detailed descriptions of the SAW parameter extraction techniques are given. A discussion of the results is provided, including a comparison of extracted parameters and an overview of possible SAW applications.

Orthogonal frequency coding for SAW tagging and sensors.

Surface acoustic wave (SAW)-based sensors can offer wireless, passive operation in numerous environments, and various device embodiments are used for retrieval of the sensed data information. Single sensor systems typically can use a single carrier frequency and a simple device embodiment because tagging is not required. In a multisensor environment, it is necessary to both identify the sensor and retrieve the sensed information. This paper presents the concept of orthogonal frequency coding (OFC) for applications to SAW sensor technology. The OFC offers all advantages inherent to spread spectrum communications, including enhanced processing gain and lower interrogation power spectral density (PSD). It is shown that the time ambiguity in the OFC compressed pulse is significantly reduced as compared with a single frequency tag having the same code length, and additional coding can be added using a pseudo-noise (PN) sequence. The OFC approach is general and should be applicable to many differing SAW sensors for temperature, pressure, liquid, gases, etc. Device embodiments are shown, and a potential transceiver is described. Measured device results are presented and compared with coupling of modes (COM) model predictions to demonstrate performance. Devices then are used in computer simulations of the proposed transceiver design, and the results of an OFC sensor system are discussed.