Tracking bioaerosol exposure among municipal solid waste workers using hematological and inflammatory biomarkers.

High levels of bioaerosols may exist in the air of municipal solid waste (MSW) management facilities, constituting a significant occupational hazard for workers. In this study, we investigated the potential association between exposure to bioaerosols and inflammatory biomarkers among municipal solid waste workers (MSWWs) at both the landfill site and the municipal solid waste transfer station (MSWTS), in comparison to a control group without exposure. Air sampling was conducted at six points around the landfill, two points at the MSWTS, and one point in a public park (as a control area) during the spring and summer of 2019. The results of our study revealed that airborne pathogens were highly prevalent at the sampling points, especially in the active zone and leachate collection pond. Aspergillus species were the predominant fungal species detected in this study, with the highest occurrence observed for Aspergillus flavus (83.3%), Aspergillus niger, and Aspergillus fumigatus (75.0%). Furthermore, Staphylococcus species accounted for over 75% of the total bacterial bioaerosols detected across all study areas. The blood test results of workers revealed a significant increase in platelets (PLT), immunoglobulin G (IgG), white blood cells (WBC), neutrophils, basophils, and high-sensitivity C-reactive protein (hs-CRP) compared to the control group. Conversely, platelet distribution width (PDW), mean platelet volume (MPV), and platelet-large cell ratio (P-LCR) in the exposed subjects exhibited a decreasing trend compared to the control group. These findings suggest a potential association between exposure to bioaerosols, particularly in the vicinity of open dumpsites, and elevated levels of hematologic and inflammatory markers in circulation. Furthermore, the influence of smoking status and confounding factors appears to be significant in both the control and exposure groups.

Sono-photo-assisted heterogeneous activation of peroxymonosulfate by Fe/CMK-3 catalyst for the degradation of bisphenol A, optimization with response surface methodology.

The present study examined the removal of bisphenol A (BPA) and total organic carbon (TOC) from aqueous solutions by the Fe/CMK-3 as peroxymonosulfate activator used in the sono-photo-catalytic process. The synthesis of Fe/CMK-3 was carried out using the co-precipitation method, and it was characterized by FTIR, XRD, BET, EDX, and TEM. The results showed that the iron nanoparticles were uniformly embedded in the CMK-3 pores. The effect of factors affecting on the removal of BPA and TOC was evaluated by response surface methodology (RSM) with center composite design (CCD). The analysis of variance of the quadratic model showed that the model is significant (p value < .0001 and R2  > 99.4%) and can be used to optimize the removal efficiency of BPA. Optimization results showed that the highest removal efficiency of BPA (100%) and TOC (80.6%) was achieved in optimum conditions of pH 7.8, catalyst dose 0.33 g/L, PMS dose 3.35 mmol/L, BPA concentration 39.3 mg/L, and 78.5 min. In addition, statistical analysis of the data showed that, in the studied range, the initial concentration of BPA was the most influential factor, followed by pH and PMS dose. Highest catalytic stability of Fe/CMK-3 showed the potential applicability of catalyst in the treatment of BPA-containing solutions. The quenching test showed that sulfate radical was the main responsible for the removal of BPA. The decrease in IOUR value after the 75-min reaction time indicates that this process has a high ability for oxidation of the pollutant and its intermediates. Generally, the observed results suggest that the Fe-CMK-3/UV/US/PMS system can be a promising procedure for the removal of persistent pollutants such as BPA from aqueous media. PRACTITIONER POINTS: Fe/CMK-3 exhibited prominent catalytic activity and high stability for peroxymonosulfate activation. Effective degradation of bisphenol A was achieved in the Fe-CMK-3/UV/US/PMS system. The effect of five factors at five levels and their interactions during the removal of BPA was evaluated by RSM method coupled with central composite design (CCD). The analysis of variance of the quadratic model showed that the model is very significant (p value < .0001) and can be used to optimize the removal efficiency of BPA. The quenching test showed that sulfate radical was the main responsible for the removal of BPA. Reducing IOUR value after the 75-min reaction time indicates that toxicity of the solution was significantly decreased in this system.