Titanium methyl tamed on silica: synthesis of a well-defined pre-catalyst for hydrogenolysis of n-alkane.

Alkylation of Ti(CH3)2Cl21 by MeLi gives the homoleptic Ti(CH3)42 for the first time in the absence of any coordinating solvent. The reaction of 2 with silica pretreated at 700 °C (SiO2-700) gives two inequivalent silica-supported Ti-methyl species 3. Complex 3 was characterized by IR, microanalysis (ICP-OES, CHNS, and gas quantification), and advanced solid-state NMR spectroscopy (1H, 13C, DQ, TQ, and HETCOR). The catalytic activity of the pre-catalyst 3 is investigated in low-temperature hydrogenolysis of propane and n-butane with TONs of 419 and 578, respectively.

Docking of tetra-methyl zirconium to the surface of silica: a well-defined pre-catalyst for conversion of CO2 to cyclic carbonates.

The metal complex (Zr(CH3)4(THF)2) has been fully synthesized, characterized and grafted onto partially dehydroxylated silica to give two surface species [([triple bond, length as m-dash]Si-O-)Zr(CH3)3(THF)2] (minor) and [([triple bond, length as m-dash]Si-O-)2Zr(CH3)2(THF)2] (major) which have been characterized by SS NMR, IR, and elemental analysis. These supported pre-catalysts exhibit the best conversion of CO2 to cyclic carbonates, as compared to the previously reported SOMC catalysts.

The Comparison between Single Atom Catalysis and Surface Organometallic Catalysis.

Single atom catalysis (SAC) is a recent discipline of heterogeneous catalysis for which a single atom on a surface is able to carry out various catalytic reactions. A kind of revolution in heterogeneous catalysis by metals for which it was assumed that specific sites or defects of a nanoparticle were necessary to activate substrates in catalytic reactions. In another extreme of the spectrum, surface organometallic chemistry (SOMC), and, by extension, surface organometallic catalysis (SOMCat), have demonstrated that single atoms on a surface, but this time with specific ligands, could lead to a more predictive approach in heterogeneous catalysis. The predictive character of SOMCat was just the result of intuitive mechanisms derived from the elementary steps of molecular chemistry. This review article will compare the aspects of single atom catalysis and surface organometallic catalysis by considering several specific catalytic reactions, some of which exist for both fields, whereas others might see mutual overlap in the future. After a definition of both domains, a detailed approach of the methods, mostly modeling and spectroscopy, will be followed by a detailed analysis of catalytic reactions: hydrogenation, dehydrogenation, hydrogenolysis, oxidative dehydrogenation, alkane and cycloalkane metathesis, methane activation, metathetic oxidation, CO2 activation to cyclic carbonates, imine metathesis, and selective catalytic reduction (SCR) reactions. A prospective resulting from present knowledge is showing the emergence of a new discipline from the overlap between the two areas.

Single-Site Molybdenum on Solid Support Materials for Catalytic Hydrogenation of N2 -into-NH3.

Very stable in operando and low-loaded atomic molybdenum on solid-support materials have been prepared and tested to be catalytically active for N2 -into-NH3 hydrogenation. Ammonia synthesis is reported at atmospheric pressure and 400 °C with NH3 rates of approximately 1.3×103  µmol h-1 gMo -1 using a well-defined Mo-hydride grafted on silica (SiO2-700 ). DFT modelling on the reaction mechanism suggests that N2 spontaneously binds on monopodal [(≡Si-O-)MoH3 ]. Based on calculations, the fourth hydrogenation step involving the release of the first NH3 molecule represents the rate-limiting step of the whole reaction. The inclusion of cobalt co-catalyst and an alkali caesium additive impregnated on a mesoporous SBA-15 support increases the formation of NH3 with rates of circa 3.5×103  µmol h-1 gMo -1 under similar operating conditions and maximum yield of 29×103  µmol h-1 gMo -1 when the pressure is increased to 30 atm.

Surface organometallic chemistry in heterogeneous catalysis.

The broad challenges of energy and environment have become a main focus of research efforts to develop more active and selective catalytic systems for key chemical transformations. Surface organometallic chemistry (SOMC) is an established concept, associated with specific tools, for the design, preparation and characterization of well-defined single-site catalysts. The objective is to enter a catalytic cycle through a presumed catalytic intermediate prepared from organometallic or coordination compounds to generate well defined surface organometallic fragments (SOMFs) or surface coordination fragments (SCFs). These notions are the basis of the "catalysis by design" strategy ("structure-activity" relationship) in which a better understanding of the mechanistic aspects of the catalytic process led to the improvement of catalyst performances. In this review the application of SOMC strategy for the design and preparation of catalysts for industrially relevant processes that are crucial to the energy and environment is discussed. In particular, the focus will be on the conversion of energy-related feedstocks, such as methane and higher alkanes that are primary products of the oil and gas industry, and of their product of combustion, CO2, whose efficient capture and conversion is currently indicated as a top priority for the environment. Among the main topics related to energy and environment, catalytic oxidation is also considered as a key subject of this review.

Predicting the DNP-SENS efficiency in reactive heterogeneous catalysts from hydrophilicity.

Identification of surfaces at the molecular level has benefited from progress in dynamic nuclear polarization surface enhanced NMR spectroscopy (DNP SENS). However, the technique is limited when using highly sensitive heterogeneous catalysts due to secondary reaction of surface organometallic fragments (SOMFs) with stable radical polarization agents. Here, we observe that in non-porous silica nanoparticles (NPs) (dparticle = 15 nm) some DNP enhanced NMR or SENS characterizations are possible, depending on the metal-loading of the SOMF and the type of SOMF substituents (methyl, isobutyl, neopentyl). This unexpected observation suggests that aggregation of the nanoparticles occurs in non-polar solvents (such as ortho-dichlorobenzene) leading to (partial) protection of the SOMF inside the interparticle space, thereby preventing reaction with bulky polarization agents. We discover that the DNP SENS efficiency is correlated with the hydrophilicity of the SOMF/support, which depends on the carbon and SOMF concentration. Nitrogen sorption measurements to determine the BET constant (CBET) were performed. This constant allows us to predict the aggregation of silica nanoparticles and consequently the efficiency of DNP SENS. Under optimal conditions, CBET > 60, we found signal enhancement factors of up to 30.

Well-defined silica supported bipodal molybdenum oxo alkyl complexes: a model of the active sites of industrial olefin metathesis catalysts.

A well-defined, silica-supported molybdenum oxo alkyl species, ([triple bond, length as m-dash]SiO-)2Mo([double bond, length as m-dash]O)(CH2tBu)2, was prepared by the selective grafting of Mo([double bond, length as m-dash]O)(CH2tBu)3Cl onto a silica partially dehydroxylated at 200 °C using a rigorous surface organometallic chemistry approach. The immobilized bipodal surface species, partly resembling the active species of industrial MoO3/SiO2 olefin metathesis catalysts, exhibited excellent functional group tolerance in conjunction with its high activity in homocoupling, self and ring closing olefin metathesis.

From single-site tantalum complexes to nanoparticles of Ta x N y and TaO x N y supported on silica: elucidation of synthesis chemistry by dynamic nuclear polarization surface enhanced NMR spectroscopy and X-ray absorption spectroscopy.

Air-stable catalysts consisting of tantalum nitride nanoparticles represented as a mixture of Ta x N y and TaO x N y with diameters in the range of 0.5 to 3 nm supported on highly dehydroxylated silica were synthesized from TaMe5 (Me = methyl) and dimeric Ta2(OMe)10 with guidance by the principles of surface organometallic chemistry (SOMC). Characterization of the supported precursors and the supported nanoparticles formed from them was carried out by IR, NMR, UV-Vis, extended X-ray absorption fine structure, and X-ray photoelectron spectroscopies complemented with XRD and high-resolution TEM, with dynamic nuclear polarization surface enhanced NMR spectroscopy being especially helpful by providing enhanced intensities of the signals of 1H, 13C, 29Si, and 15N at their natural abundances. The characterization data provide details of the synthesis chemistry, including evidence of (a) O2 insertion into Ta-CH3 species on the support and (b) a binuclear to mononuclear transformation of species formed from Ta2(OMe)10 on the support. A catalytic test reaction, cyclooctene epoxidation, was used to probe the supported nanoparticles, with 30% H2O2 serving as the oxidant. The catalysts gave selectivities up to 98% for the epoxide at conversions as high as 99% with a 3.4 wt% loading of Ta present as Ta x N y /TaO x N y .

Single site silica supported tetramethyl niobium by the SOMC strategy: synthesis, characterization and structure-activity relationship in the ethylene oligomerization reaction.

A silica supported tetramethyl niobium complex [([triple bond, length as m-dash]SiO)NbMe4] 2 has been isolated by the surface alkylation of [([triple bond, length as m-dash]SiO-)NbCl3Me] 1 with dimethyl zinc in pentane. 1 can be easily synthesized by grafting NbCl3Me2 onto the surface of partially dehydroxylated silica by the SOMC strategy. Precise structural analysis was carried out using FTIR, advanced solid state NMR, elemental analysis and mass balance techniques (gas quantification after treating 2 with degassed water). Complex 1 was found to be active in the ethylene oligomerization reaction, producing up to C30, whereas to our surprise complex 2 selectively dimerized ethylene into 1-butene in the absence of a co-catalyst at the same conversion level.

Reactive surface organometallic complexes observed using dynamic nuclear polarization surface enhanced NMR spectroscopy.

Dynamic Nuclear Polarization Surface Enhanced NMR Spectroscopy (DNP SENS) is an emerging technique that allows access to high-sensitivity NMR spectra from surfaces. However, DNP SENS usually requires the use of radicals as an exogenous source of polarization, which has so far limited applications for organometallic surface species to those that do not react with the radicals. Here we show that reactive surface species can be studied if they are immobilized inside porous materials with suitably small windows, and if bulky nitroxide bi-radicals (here TEKPol) are used as the polarization source and which cannot enter the pores. The method is demonstrated by obtaining significant DNP enhancements from highly reactive complelxes [([triple bond, length as m-dash]Si-O-)W(Me)5] supported on MCM-41, and effects of pore size (6.0, 3.0 and 2.5 nm) on the performance are discussed.

Unearthing a Well-Defined Highly Active Bimetallic W/Ti Precatalyst Anchored on a Single Silica Surface for Metathesis of Propane.

Two compatible organometallic complexes, W(Me)6 (1) and TiNp4 (2), were successively anchored on a highly dehydroxylated single silica support (SiO2-700) to synthesize the well-defined bimetallic precatalyst [(≡Si-O-)W(Me)5(≡Si-O-)Ti(Np)3] (4). Precatalyst 4 was characterized at the molecular level using advanced surface organometallic chemistry (SOMC) characterization techniques. The strong autocorrelation observed between methyl of W and Ti in 1H-1H multiple-quantum NMR spectra demonstrates that W and Ti species are in close proximity to each other. The bimetallic precatalyst 4, with a turnover number (TON) of 9784, proved to be significantly more efficient than the silica-supported monometallic catalyst [(≡Si-O-)W(Me)5] (3), with a TON of 98, for propane metathesis at 150 °C in a flow reactor. The dramatic improvement in the activity signifies the cooperativity between Ti and W and indicates that the key step of alkane metathesis (C-H bond activation followed by ß-H elimination) occurs on Ti, followed by olefin metathesis, which occurs on W. We have demonstrated the influence and importance of proximity of Ti to W for achieving such a significantly high activity. This is the first report demonstrating the considerably high activity (TON = 9784) in propane metathesis at moderate temperature (150 °C) using a well-defined bimetallic system prepared via the SOMC approach.

Well-Defined Molybdenum Oxo Alkyl Complex Supported on Silica by Surface Organometallic Chemistry: A Highly Active Olefin Metathesis Precatalyst.

The well-defined silica-supported molybdenum oxo alkyl species (≡SiO-)MoO(CH2tBu)3 was selectively prepared by grafting of MoO(CH2tBu)3Cl onto partially dehydroxylated silica (silica700) using the surface organometallic chemistry approach. This surface species was fully characterized by elemental analysis and DRIFT, solid-state NMR, and EXAFS spectroscopy. This new material is related to the active species of industrial supported MoO3/SiO2 olefin metathesis catalysts. It displays very high activity in propene self-metathesis at mild (turnover number = 90 000 after 25 h). Remarkably, its catalytic performance outpaces those of the parent imido derivative and its tungsten oxo analogue.

SOMC-Designed Silica Supported Tungsten Oxo Imidazolin-2-iminato Methyl Precatalyst for Olefin Metathesis Reactions.

Synthesis, structure, and olefin metathesis activity of a surface complex [(≡Si-O-)W(═O)(CH3)2-ImDippN] (4) (ImDipp = 1,3-bis(2,6-diisopropylphenyl)imidazolin-2-iminato) supported on silica by a surface organometallic chemistry (SOMC) approach are reported. The reaction of N-silylated 2-iminoimidazoline with tungsten(VI) oxytetrachloride generated the tungsten oxo imidazolin-2-iminato chloride complex [ImDippNW(═O)Cl3] (2). This was grafted on partially dehydroxylated silica pretreated at 700 °C (SiO2-700) to afford a well-defined monopodal surface complex [(≡Si-O-)W(═O)Cl2-ImDippN] (3). 3 underwent alkylation by ZnMe2 to produce [(≡Si-O-)W(═O)(CH3)2-ImDippN] (4). The alkylated surface complex was thoroughly characterized by solid-state NMR, elemental microanalysis, Raman, FT-IR spectroscopies, and XAS analysis. 4 proved to be an active precatalyst for self-metathesis of terminal olefins such as propylene and 1-hexene.

Synthesis and characterization of a homogeneous and silica supported homoleptic cationic tungsten(vi) methyl complex: application in olefin metathesis.

A method for the synthesis of a homogeneous cationic tungsten(vi)pentamethyl complex [(WMe5)+(C6F5)3BMe-] from neutral tungstenhexamethyl (WMe6) and a silica supported cationic tungstentetramethyl complex [([triple bond, length as m-dash]Si-O-)WMe4+ (C6F5)3BMe-] from a neutral silica supported tungstenpentamethyl complex [([triple bond, length as m-dash]Si-O-)WMe5] is described. In both cases a direct demethylation using the B(C6F5)3 reagent was used. The aforesaid complexes were characterized by liquid or solid state NMR spectroscopy. Interestingly, the homogeneous cationic complex [(WMe5)+(C6F5)3BMe-] shows moderate activity whereas the supported cationic complex [([triple bond, length as m-dash]Si-O-)WMe4+(C6F5)3BMe-] exhibits good activity in olefin metathesis reactions.

Synergy between Two Metal Catalysts: A Highly Active Silica-Supported Bimetallic W/Zr Catalyst for Metathesis of n-Decane.

A well-defined, silica-supported bimetallic precatalyst [≡Si-O-W(Me)5≡Si-O-Zr(Np)3] (4) has been synthesized for the first time by successively grafting two organometallic complexes [W(Me)6 (1) followed by ZrNp4 (2)] on a single silica support. Surprisingly, multiple-quantum NMR characterization demonstrates that W and Zr species are in close proximity to each other. Hydrogenation of this bimetallic catalyst at room temperature showed the easy formation of zirconium hydride, probably facilitated by tungsten hydride which was formed at this temperature. This bimetallic W/Zr hydride precatalyst proved to be more efficient (TON = 1436) than the monometallic W hydride (TON = 650) in the metathesis of n-decane at 150 °C. This synergy between Zr and W suggests that the slow step of alkane metathesis is the C-H bond activation that occurs on Zr. The produced olefin resulting from a ß-H elimination undergoes easy metathesis on W.

Controlling the hydrogenolysis of silica-supported tungsten pentamethyl leads to a class of highly electron deficient partially alkylated metal hydrides.

The well-defined single-site silica-supported tungsten complex [([triple bond, length as m-dash]Si-O-)W(Me)5], 1, is an excellent precatalyst for alkane metathesis. The unique structure of 1 allows the synthesis of unprecedented tungsten hydrido methyl surface complexes via a controlled hydrogenolysis. Specifically, in the presence of molecular hydrogen, 1 is quickly transformed at -78 °C into a partially alkylated tungsten hydride, 4, as characterized by 1H solid-state NMR and IR spectroscopies. Species 4, upon warming to 150 °C, displays the highest catalytic activity for propane metathesis yet reported. DFT calculations using model systems support the formation of [([triple bond, length as m-dash]Si-O-)WH3(Me)2], as the predominant species at -78 °C following several elementary steps of hydrogen addition (by σ-bond metathesis or α-hydrogen transfer). Rearrangement of 4 occuring between -78 °C and room temperature leads to the formation of an unique methylidene tungsten hydride [([triple bond, length as m-dash]Si-O-)WH3([double bond, length as m-dash]CH2)], as determined by solid-state 1H and 13C NMR spectroscopies and supported by DFT. Thus for the first time, a coordination sphere that incorporates both carbene and hydride functionalities has been observed.

Effect of support on metathesis of n-decane: drastic improvement in alkane metathesis with WMe5 linked to silica-alumina.

[WMe6 ] (1) supported on the surface of SiO2 -Al2 O3(500) (2) has been extensively characterized by solid-state NMR spectroscopy, elemental analysis, and gas quantification, which clearly reveal the formation of a mixture of monopodal and bipodal species with the migration of methyl from W to Al. The supported species SiO2 -Al2 O3(500) (2) transformed at 120 °C into two types of carbynic centers, one of which is cationic and the other neutral. These species are very efficient for the metathesis of n-decane. Comparison with already-synthesized neutral bipodal tungsten indicates that the high increase in activity is due to the cationic character of the grafted tungsten.

Cyclooctane metathesis catalyzed by silica-supported tungsten pentamethyl [(≡SiO)W(Me)5]: distribution of macrocyclic alkanes.

Metathesis of cyclic alkanes catalyzed by the new surface complex [(≡SiO)W(Me)5] affords a wide distribution of cyclic and macrocyclic alkanes. The major products with the formula C(n)H(2n) are the result of either a ring contraction or ring expansion of cyclooctane leading to lower unsubstituted cyclic alkanes (5≤n≤7) and to an unprecedented distribution of unsubstituted macrocyclic alkanes (12≤n≤40), respectively, identified by GC/MS and by NMR spectroscopies.