Virus adsorbent systems based on Amazon holocellulose and nanomaterials.

The environment preservation has been an important motivation to find alternative, functional, and biodegradable materials to replace polluting petrochemicals. The production of nonbiodegradable face masks increased the concentration of microplastics in the environment, highlighting the need for sustainable alternatives, such as the use of local by-products to create efficient and eco-friendly filtering materials. Furthermore, the use of smart materials can reduce the risk of contagion and virus transmission, especially in the face of possible mutations. The development of novel materials is necessary to ensure less risk of contagion and virus transmission, as well as to preserve the environment. Taking these factors into account, 16 systems were developed with different combinations of precursor materials (holocellulose, polyaniline [ES-PANI], graphene oxide [GO], silver nanoparticles [AgNPs], and activated carbon [AC]). Adsorption tests of the spike protein showed that the systems containing GO and AC were the most efficient in the adsorption process. Similarly, plate tests conducted using the VSV-IN strain cultured in HepG2 cells showed that the system containing all phases showed the greatest reduction in viral titer method. In agreement, the biocompatibility tests showed that the compounds extracted from the systems showed low cytotoxicity or no significant cytotoxic effect in human fibroblasts. As a result, the adsorption tests of the spike protein, viral titration, and biocompatibility tests showed that systems labeled as I and J were the most efficient. In this context, the present research has significantly contributed to the technological development of antiviral systems, with improved properties and increased adsorption efficiency, reducing the viral titer and contributing efficiently to public health. In this way, these alternative materials could be employed in sensors and devices for filtering and sanitization, thus assisting in mitigating the transmission of viruses and bacteria. RESEARCH HIGHLIGHTS: Sixteen virus adsorbent systems were developed with different combinations of precursor materials (holocellulose, polyaniline (ES-PANI), graphene oxide (GO), silver nanoparticles (AgNPs), and activated carbon (AC)). The system that included all of the nanocomposites holocellulose, PANI, GO, AgNPs, and AC showed the greatest reduction in viral titration. The biocompatibility tests revealed that all systems caused only mild or moderate cytotoxicity toward human fibroblasts.

Pouteria spp. fruits: Health benefits of bioactive compounds and their potential for the food industry.

The Sapotaceae family encompasses the genus Pouteria spp., comprising approximately 1,250 species of fruits cherished by consumers for their delightful assortment and flavors. Over the years, extensive research has been devoted to exploring the natural bioactive compounds present in these fruits, with the primary goal of preventing and/or mitigating the risk of degenerative diseases. Despite their widespread popularity in numerous countries, the chemistry, nutritional content, and biological potential of these fruits remain relatively unexplored. This comprehensive review aims to shed light on the principal volatile and non-volatile chemical components found in Pouteria fruits, which present notable antioxidant properties. By doing so, a broad perspective on the current trends in characterizing these compounds and their potential applications were provided, as well as the associated health benefits. Additionally, the prospects and potential applications of Pouteria fruits in the food industry were explored herein.

Hibiscus acetosella: An Unconventional Alternative Edible Flower Rich in Bioactive Compounds.

The interest in the consumption of edible flowers has increased since they represent a rich source of bioactive compounds, which are significantly beneficial to human health. The objective of this research was to access the bioactive compounds and antioxidant and cytotoxic properties of unconventional alternative edible flowers of Hibiscus acetosella Welw. Ex Hiern. The edible flowers presented pH value of 2.8 ± 0.00, soluble solids content of 3.4 ± 0.0 °Brix, high moisture content of about 91.8 ± 0.3%, carbohydrates (6.9 ± 1.2%), lipids (0.90 ± 0.17%), ashes (0.4 ± 0.0%), and not detectable protein. The evaluation of the scavenging activity of free radicals, such as 2,2-diphenyl-1-picryl-hydrazyl (DPPH) and 2,2'-azinobis-(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS), of the flower extract was better than the results observed for other edible flowers (507.8 ± 2.7 µM TE and 783.9 ± 30.8 µM TE, respectively) as well as the total phenolic composition (TPC) value (568.8 ± 0.8 mg GAE/g). These flowers are rich in organic acids and phenolic compounds, mainly myricetin, and quercetin derivatives, kaempferol, and anthocyanins. The extract showed no cytotoxicity for the cell lineages used, suggesting that the extract has no directly harmful effects to cells. The important bioactive compound identified in this study makes this flower especially relevant in the healthy food area due to its nutraceutical potential without showing cytotoxicity.

Cold plasma as a pre-treatment for processing improvement in food: A review.

Thermal processes can be very damaging to the nutritional and sensory quality of foods. Non-thermal technologies have been applied to reduce the impact of heat on food, reducing processing time and increasing its efficiency. Among many non-thermal technologies, cold plasma is an emerging technology with several potential applications in food processing. This technique can be used to preserve and sanitize food products, and act as a pre-treatment for drying, extraction, cooking, curing, and hydrogenation of foods. Furthermore, the reacting plasma species formed during the plasma application can change positively the sensory and nutritional aspects of foods. The aim of this review is to analyze the main findings on the application of cold plasma as a pre-treatment technology to improve food processing. In its current maturity stage, the cold plasma technology is suitable for reducing drying time, increasing extraction efficiency, as well as curing meats. This technology can convert unsaturated into saturated fats, without forming trans isomers, which can be an alternative to healthier foods. Although many advantages come from cold plasma applications, this technology still has several challenges, such as the scaling up, especially in increasing productivity and treating foods with large formats. Optimization and control of the effects of plasma on nutritional and sensory quality are still under investigation. Further improvement of the technology will come with a higher knowledge of the effects of plasma on the different chemical groups present in foods, and with the development of bigger or more powerful plasma systems.

Passion fruit (Passiflora spp.) pulp: A review on bioactive properties, health benefits and technological potential.

The Passiflora genus (Passifloraceae family) extends worldwide, but it is mainly found in the Americas. The present review aimed to select the main reports published over the last 5 years involving the chemical composition, health benefits, and products obtained from the pulps of Passifora spp. The pulps of at least 10 species of Passiflora have been studied presenting different classes of organic compounds, especially phenolic acids, and polyphenols. The main bioactivity properties include antioxidant and in vitro α-amylase and α-glucosidase enzyme inhibition. These reports highlight the potential of Passiflora for the development of a variety of products, especially fermented and non-fermented beverages, as well as foods to attend a demand for non-dairy products. In general, these products are prominent source of probiotic bacteria resistant to in vitro gastrointestinal simulation, representing an alternative for intestinal microbiota regulation. Therefore, sensory analysis is encouraging herein, as well as in vivo tests to enable the development of high value pharmaceuticals and food products. The patents confirm the great interest in research and products development in different food technology areas, as well as in biotechnology, pharmacy, and materials engineering.

Structure and interaction roles in the release profile of chalcone-loaded liposomes.

The structures and molecular interactions of established synthetic chalcones were correlated with their release profiles from asolectin liposomes. The effects of chalcones on the properties of liposomes were evaluated by dynamic light scattering (DLS), ultraviolet-visible spectroscopy (UV-VIS), horizontal attenuated total reflection Fourier transform infrared (HATR-FTIR), 31P nuclear magnetic resonance (31P NMR), zeta (ζ) potential and differential scanning calorimetry (DSC). The profiles and mechanisms of release were accessed according to the Korsmeyer-Peppas model. Results obtained allowed the establishment of a relationship between the chalcone release profile and 1) the ordering effects of chalcones in different membrane regions, 2) their polar or interfacial location in the lipid layer, 3) the influence of hydroxy and methoxy substituents, 4) their effect on reorientation of lipid choline-phosphate regions. The obtained data may improve the development of chalcone-based systems to be used in the therapy of chronic and acute diseases.

Biodefensive Based on Piper nigrum Essential Oil for Controlling of Anopheles aquasalis Larvae: Influence of Temperature (35 °C) and Preservatives.

Considerable efforts have been spent on the development of biodefensives based on the encapsulation of essential oils for controlling of urban pests from their larval stage, especially as anopheline controlling agents. The larval source management of Anopheles aquasalis is important for malaria prevention. For this reason, this research proposes larvicidal biodefensives based on polymeric particles loaded with Piper nigrum essential oil, considering the influence of temperature (35 °C) and preservatives on the formulation stability. The biodefensive containing the preservative phenoxyethanol/methylisothiazolinone (PNE) resulted in 5 months of shelf-life storage with an Encapsulation Efficiency (EE%) of essential oil of 70%. The biodefensive PNE (containing 500 µg.mL-1 of encapsulated essential oil) presented a polydisperse particle size distribution, ranging from D10 = (127 ± 10) nm to D90 = (472 ± 78) nm and a particle mean size of (236 ± 34) nm. The AFM images revealed a spherical morphology with an external surface almost regular and smooth. The controlled release of the essential oil was evaluated up to 72 h according to the Korsmeyer-Peppas mathematical model, confirming the anomalous transport (n = 0.64 in pH = 3 and pH = 10, and n = 0.65 in pH = 7). The total larvae mortality on the in loco bioassays was almost reached (92%) after 24 h. However, according to the in vitro bioassays applying the in natura essential oil alone, the concentration of 454 µg.mL-1 resulted on the mortality of 70% of the larvae after 24 h. For this reason, the highest efficiency of the biodefensive PNE may be related to the encapsulation of essential oil, delivering the loaded particles more efficiently inside the larvae. From this perspective, the present study shows that a formulation based on P. nigrum essential oil may be taken into account in the integrated management of disease vector mosquitoes.

Head-to-Tail and Head-to-Head Molecular Chains of Poly(p-Anisidine): Combined Experimental and Theoretical Evaluation.

Poly(p-anisidine) (PPA) is a polyaniline derivative presenting a methoxy (-OCH3) group at the para position of the phenyl ring. Considering the important role of conjugated polymers in novel technological applications, a systematic, combined experimental and theoretical investigation was performed to obtain more insight into the crystallization process of PPA. Conventional oxidative polymerization of p-anisidine monomer was based on a central composite rotational design (CCRD). The effects of the concentration of the monomer, ammonium persulfate (APS), and HCl on the percentage of crystallinity were considered. Several experimental techniques such as X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), multifractal analysis, Nuclear Magnetic Resonance (13C NMR), Fourier-transform Infrared spectroscopy (FTIR), and complex impedance spectroscopy analysis, in addition to Density Functional Theory (DFT), were employed to perform a systematic investigation of PPA. The experimental treatments resulted in different crystal structures with a percentage of crystallinity ranging from (29.2 ± 0.6)% (PPA1HT) to (55.1 ± 0.2)% (PPA16HT-HH). A broad halo in the PPA16HT-HH pattern from 2θ = 10.0-30.0° suggested a reduced crystallinity. Needle and globular-particle morphologies were observed in both samples; the needle morphology might have been related to the crystalline contribution. A multifractal analysis showed that the PPA surface became more complex when the crystallinity was reduced. The proposed molecular structures of PPA were supported by the high-resolution 13C NMR results, allowing us to access the percentage of head-to-tail (HT) and head-to-head (HH) molecular structures. When comparing the calculated and experimental FTIR spectra, the most pronounced changes were observed in ν(C-H), ν(N-H), ν(C-O), and ν(C-N-C) due to the influence of counterions on the polymer backbone as well as the different mechanisms of polymerization. Finally, a significant difference in the electrical conductivity was observed in the range of 1.00 × 10-9 S.cm-1 and 3.90 × 10-14 S.cm-1, respectively, for PPA1HT and PPA16HT-HH.

Encapsulation of Bromelain in Combined Sodium Alginate and Amino Acid Carriers: Experimental Design of Simplex-Centroid Mixtures for Digestibility Evaluation.

Bromelain has potential as an analgesic, an anti-inflammatory, and in cancer treatments. Despite its therapeutic effects, this protein undergoes denaturation when administered orally. Microencapsulation processes have shown potential in protein protection and as controlled release systems. Thus, this paper aimed to develop encapsulating systems using sodium alginate as a carrier material and positively charged amino acids as stabilizing agents for the controlled release of bromelain in in vitro tests. The systems were produced from the experimental design of centroid simplex mixtures. Characterizations were performed by FTIR showing that bromelain was encapsulated in all systems. XRD analyses showed that the systems are semi-crystalline solids and through SEM analysis the morphology of the formed systems followed a pattern of rough microparticles. The application of statistical analysis showed that the systems presented behavior that can be evaluated by quadratic and special cubic models, with a p-value < 0.05. The interaction between amino acids and bromelain/alginate was evaluated, and free bromelain showed a reduction of 74.0% in protein content and 23.6% in enzymatic activity at the end of gastric digestion. Furthermore, a reduction of 91.6% of protein content and 65.9% of enzymatic activity was observed at the end of intestinal digestion. The Lis system showed better interaction due to the increased stability of bromelain in terms of the amount of proteins (above 63% until the end of the intestinal phase) and the enzymatic activity of 89.3%. Thus, this study proposes the development of pH-controlled release systems aiming at increasing the stability and bioavailability of bromelain in intestinal systems.

Temperature Dependence of the Electrical Properties of Na2Ti3O7/Na2Ti6O13/POMA Composites.

The temperature dependence of the electrical properties of composites formed by biphasic sodium titanate and poly(o-methoxyaniline) (Na2Ti3O7/Na2Ti6O13/POMA) with different concentrations of POMA (0%, 1%, 10%, 15%, 35% and 50%) in the ceramic matrix was determined from measurements of complex impedance. The structural details were studied by means of X-ray diffraction, confirming the formation of the Na2Ti3O7/Na2Ti6O13/POMA composites. The displacement of the (200) reflection from 2θ = 10.45° to 11.15° in the composites with 10 and 15% of POMA suggested the partial replacement of H+ for Na+ in the Na2Ti3O7 structure. The thermal properties were investigated by Thermogravimetry and Differential Thermal Analysis. The Thermogravimetry curves of the composites with POMA content of 1, 10 and 15% presented profiles similar to that of pure sodium titanate sample. The composites with 35 and 50% of POMA showed a process at temperatures around 60-70 °C, which was associated with water absorbed by the polymer. The analysis of the complex impedance spectroscopy measurements revealed that the electrical resistivity of the composites in the range from 0 to 35% increased by two orders of magnitude, with different values for each concentration. This positive temperature coefficient of resistivity was less noticeable in the composite with highest POMA mass content (50%). The rapid increase in resistivity caused an increase in the relaxation time calculated from the time domain. The electrical response of the 50% of POMA compound changes in relation to what was observed in the other compounds, which suggests that there is a saturation limit in the increase in resistivity with POMA content.

PLGA-PVA-PEG Single Emulsion Method as a Candidate for Aminolevulinic Acid (5-ALA) Encapsulation: Laboratory Scaling Up and Stability Evaluation.

One of the most widely used molecules used for photodynamic therapy (PDT) is 5-aminolevulinic acid (5-ALA), a precursor in the synthesis of tetrapyrroles such as chlorophyll and heme. The 5-ALA skin permeation is considerably reduced due to its hydrophilic characteristics, decreasing its local bioavailability and therapeutic effect. For this reason, five different systems containing polymeric particles of poly [D, L-lactic-co-glycolic acid (PLGA)] were developed to encapsulate 5-ALA based on single and double emulsions methodology. All systems were standardized (according to the volume of reagents and mass of pharmaceutical ingredients) and compared in terms of laboratory scaling up, particle formation and stability over time. UV-VIS spectroscopy revealed that particle absorption/adsorption of 5-ALA was dependent on the method of synthesis. Different size distribution was observed by DLS and NTA techniques, revealing that 5-ALA increased the particle size. The contact angle evaluation showed that the system hydrophobicity was dependent on the surfactant and the 5-ALA contribution. The FTIR results indicated that the type of emulsion influenced the particle formation, as well as allowing PEG functionalization and interaction with 5-ALA. According to the 1H-NMR results, the 5-ALA reduced the T1 values of polyvinyl alcohol (PVA) and PLGA in the double emulsion systems due to the decrease in molecular packing in the hydrophobic region. The results indicated that the system formed by single emulsion containing the combination PVA-PEG presented greater stability with less influence from 5-ALA. This system is a promising candidate to successfully encapsulate 5-ALA and achieve good performance and specificity for in vitro skin cancer treatment.

Pulsatile Controlled Release and Stability Evaluation of Polymeric Particles Containing Piper nigrum Essential Oil and Preservatives.

Considerable efforts have been spent on environmentally friendly particles for the encapsulation of essential oils. Polymeric particles were developed to encapsulate the essential oil from Piper nigrum based on gelatin and poly-ε-caprolactone (PCL) carriers. Gas Chromatography ((Flame Ionization Detection (GC/FID) and Mass Spectrometry (GC/MS)), Atomic Force Microscopy (AFM), Nanoparticle Tracking Analysis (NTA), Confocal Laser Scanning Microscopy (CLSM), Attenuated Total Reflectance-Fourier-transform Infrared Spectroscopy (ATR-FTIR), and Ultraviolet-Visible (UV-VIS) spectroscopy were used for the full colloidal system characterization. The essential oil was mainly composed of ß-caryophyllene (~35%). The stability of the encapsulated systems was evaluated by Encapsulation Efficiency (EE%), electrical conductivity, turbidity, pH, and organoleptic properties (color and odor) after adding different preservatives. The mixture of phenoxyethanol/isotialzoni-3-one (PNE system) resulted in enhanced stability of approximately 120 and 210 days under constant handling and shelf-life tests, respectively. The developed polymeric system presented a similar controlled release in acidic, neutral, or basic pH, and the release curves suggested a pulsatile release mechanism due to a complexation of essential oil in the PCL matrix. Our results showed that the developed system has potential as an alternative stable product and as a controlling agent, due to the pronounced bioactivity of the encapsulated essential oil.

PANI-WO3·2H2O Nanocomposite: Phase Interaction and Evaluation of Electronic Properties by Combined Experimental Techniques and Ab-Initio Calculation.

The development of conjugated polymer-based nanocomposites by adding metallic particles into the polymerization medium allows the proposition of novel materials presenting improved electrical and optical properties. Polyaniline Emeraldine-salt form (ES-PANI) has been extensively studied due to its controllable electrical conductivity and oxidation states. On the other hand, tungsten oxide (WO3) and its di-hydrated phases, such as WO3·2H2O, have been reported as important materials in photocatalysis and sensors. Herein, the WO3·2H2O phase was directly obtained during the in-situ polymerization of aniline hydrochloride from metallic tungsten (W), allowing the formation of hybrid nanocomposites based on its full oxidation into WO3·2H2O. The developed ES-PANI-WO3·2H2O nanocomposites were successfully characterized using experimental techniques combined with Density Functional Theory (DFT). The formation of WO3·2H2O was clearly verified after two hours of synthesis (PW2 nanocomposite), allowing the confirmation of purely physical interaction between matrix and reinforcement. As a result, increased electrical conductivity was verified in the PW2 nanocomposite: the DFT calculations revealed a charge transfer from the p-orbitals of the polymeric phase to the d-orbitals of the oxide phase, resulting in higher conductivity when compared to the pure ES-PANI.

Alternative Controlling Agent of Theobroma grandiflorum Pests: Nanoscale Surface and Fractal Analysis of Gelatin/PCL Loaded Particles Containing Lippia origanoides Essential Oil.

A new systematic structural study was performed using the Atomic Force Microscopy (AFM) reporting statistical parameters of polymeric particles based on gelatin and poly-ε-caprolactone (PCL) containing essential oil from Lippia origanoides. The developed biocides are efficient alternative controlling agents of Conotrachelus humeropictus and Moniliophtora perniciosa, the main pests of Theobroma grandiflorum. Our results showed that the particles morphology can be successfully controlled by advanced stereometric parameters, pointing to an appropriate concentration of encapsulated essential oil according to the particle surface characteristics. For this reason, the absolute concentration of 1000 µg·mL-1 (P1000 system) was encapsulated, resulting in the most suitable surface microtexture, allowing a faster and more efficient essential oil release. Loaded particles presented zeta potential around (-54.3 ± 2.3) mV at pH = 8, and particle size distribution ranging from 113 to 442 nm. The hydrodynamic diameter of 90% of the particle population was found to be up to (405 ± 31) nm in the P1000 system. The essential oil release was evaluated up to 80 h, with maximum release concentrations of 63% and 95% for P500 and P1000, respectively. The best fit for the release profiles was obtained using the Korsmeyer-Peppas mathematical model. Loaded particles resulted in 100% mortality of C. humeropictus up to 48 h. The antifungal tests against M. perniciosa resulted in a minimum inhibitory concentration of 250 µg·mL-1, and the P1000 system produced growth inhibition up to 7 days. The developed system has potential as alternative controlling agent, due to its physical stability, particle surface microtexture, as well as pronounced bioactivity of the encapsulated essential oil.

Buriti (Mauritia flexuosa L. f.): An Amazonian fruit with potential health benefits.

The Amazon region has a significant biodiversity composed of several fruits with health benefits and distinguished potential for technological application and development of novel products. Buriti (Mauritia flexuosa) is one of the main Amazonian fruits with expressive nutraceutical properties. For this reason, this review aims to elucidate the current state of knowledge on buriti, providing information on its bioactive compounds, nutraceutical, and health potential for both technological and economic development especially in food and pharmaceutical areas. Different parts of buriti are important sources of carotenoids, fatty acids, phenolic compounds, and fibers. Antioxidant, antimicrobial, prebiotic, anti-diabetes, and anti-cancer properties have also been reported. In addition, the buriti oil presents a synergistic effect with antibiotics and it has been also an alternative to artificial dyes. However, there is a lack of information about the in vivo evaluation of the buriti's bioactive compounds providing a clearer elucidation on its biological potential, toxicity information and mechanisms of action. Proper sensory methods and the relationship between sensory quality and consumer perception are also needed to extend the possibility of developing new products. Finally, the use of non-thermal techniques is encouraged to improve the bioavailability of nutraceutical compounds and potentiate their action on human health.

Nanoscale surface dynamics of spatial patterns of polymeric bilayered particles loaded with essential oil.

Gelatin/PCL bilayered particles loaded with Piper nigrum essential oil was synthesized aiming to access their morphological and surface dynamic patterns. Atomic force microscopy (AFM) was applied to investigate the 3D morphology and multifractal aspects of the particles surface. The AFM maps revealed spherical surfaces and well dispersed particles, besides a rougher surface on the loaded system. Minkowski functionals showed that shape of the rough peaks was similar in the unloaded and loaded systems; however, the presence of deep valleys on the loaded particles revealed their rougher pattern. Multifractal analysis revealed that unloaded and loaded particles presented multifractal behavior with different surface dynamics. The loaded surface presented a greater width of the multifractal spectrum and smaller difference of fractal dimensions, confirming their more vertically growing. These results can be useful in the development of novel polymeric-based particles loaded with essential oil. Their unique surface dynamics can provide enhanced physical properties and performance in emerging biotechnological applications.

Poly(o-methoxyaniline) Chain Degradation Based on a Heat Treatment (HT) Process: Combined Experimental and Theoretical Evaluation.

Poly(o-methoxyaniline) emeraldine-salt form (ES-POMA) was chemically synthesized using hydrochloric acid and subjected to a heat treatment (HT) process for 1 h at 100 °C (TT100) and 200 °C (TT200). The HT process promoted a progressive decrease in crystallinity. The Le Bail method revealed a decomposition from tetrameric to trimeric-folded chains after the HT process. The unheated POMA-ES presented a globular vesicular morphology with varied micrometric sizes. The heat treatment promoted a reduction in these globular structures, increasing the non-crystalline phase. The boundary length (S) and connectivity/Euler feature (χ) parameters were calculated from the SEM images, revealing that ES-POMA presented a wide distribution of heights. The TT100 and TT200 presented a narrow boundary distribution, suggesting smoother surfaces with smaller height variations. The UV-VIS analysis revealed that the transition at 343 nm (nonlocal π → π*) was more intense in the TT200 due to the electronic delocalization, which resulted from the reduced polymer chain caused by the HT process. In addition to the loss of conjugation, counter ion withdrawal reduced the ion-chain interaction, decreasing the local electron density. This result shows the influence of the chlorine counter ions on the peaks position related to the HOMO → LUMO transition, since the π → polaron transition occurs due to the creation of the energy states due to the presence of counter ions. Finally, the electrical conductivity decreased after the HT process from 1.4 × 10-4 S.cm-1 to 2.4 × 10-6 S.cm-1 as result of the polymer deprotonation/degradation. Thus, this paper proposed a systematic evaluation of the POMA molecular structure and crystallite size and shape after heat treatment.

Three-Dimensional Nanoscale Morphological Surface Analysis of Polymeric Particles Containing Allium sativum Essential Oil.

Biodegradable particles were developed using poly-ε-caprolactone and gelatin carriers containing different concentrations of Allium sativum essential oil (EO) (360 µg/mL, 420 µg/mL, and 460 µg/mL). Atomic force microscopy was useful to evaluate the particles' surface based on morphological parameters. The particles' size varied from 150 nm to 300 nm. The diameter was related to the increase of the particles' height as a function of the EO concentration, influencing the roughness of the surface core values (from 20 to 30 nm) and surface irregularity. The spatial parameters Str (texture aspect ratio) and Std (texture direction) revealed low spatial frequency components. The hybrid parameters Sdq (root mean square gradient) and Sdr (interfacial area ratio) also increased as a function of the EO concentration, revealing fewer flat particles. On the other hand, the functional parameters (inverse areal material ratio and peak extreme height) suggested differences in surface irregularities. Higher concentrations of EO resulted in greater microtexture asperity on the particles' surface, as well as sharper peaks. The nanoscale morphological surface analysis allowed the determination of the most appropriate concentration of encapsulated EO, influencing statistical surface parameters.

Ficus spp. fruits: Bioactive compounds and chemical, biological and pharmacological properties.

The aim of this review was to compile the main reports over the last 5 years concerning the Ficus spp. fruits (Moraceae family) based on chemistry, properties, and applications as products. About 30 Ficus spp. fruits were reported focusing on their chemical composition rich in phenolic acids such as gallic, caffeic and chlorogenic acids, as well as quercetin and cyanidin derivatives. The fruits from Moraceae family presented mainly antioxidant and antimicrobial properties in addition to other functional properties to consumers health. Therefore, these fruits can be successfully considered by the food industry for the development of new products with high added value and also be considered a source of bioactive compounds.

Microscopy-based infrared spectroscopy as a tool to evaluate the influence of essential oil on the surface of loaded bilayered-nanoparticles.

Increasing interest in nanoparticles of technological application has been improving their fabrication processes. The encapsulation of essential oils as bioactive compounds has proved to be an excellent alternative to the use of less environment friendly compounds. However, the difficulty of identifying their constitution and interaction with carrier agents have aroused scientific interest and a problem to overcome. Bilayer-based nanoparticles were developed using gelatin and poly-ε-caprolactone (PCL) aiming the encapsulation ofPiper nigrumessential oil. based on atomic force microscopy images and dynamic light scattering analysis, the size of the unloaded and loaded nanoparticles was found around (194 ± 40) and (296 ± 54) nm, respectively. The spatial patterns revealed that the surface of nanoparticles presented different surface roughness, similar shapes and height distribution asymmetry, lower dominant spatial frequencies, and different spatial complexity. Traditional infrared spectroscopy allowed the identification of the nanoparticle outermost layer formed by the gelatin carrier, but microscopy-based infrared spectroscopy revealed a band at 1742 cm-1related to the carbonyl stretching mode of PCL, as well as a band at 1557 cm-1due to the amide II group from gelatin. The combination of microscopy and spectroscopy techniques proved to be an efficient alternative to quickly identify differences in chemical composition by evaluating different functional groups in bilayer PLC/gelatin nanoparticles of technological application.