Evaluation of Transmission Near the Christiansen Wavelength for Dynamic Sand Samples.

Many optical applications, including free-space optical communications, lidar, and astronomical measurements, are impacted by the presence of light-scattering particles also known as obscurants. Scattering from particles consisting of sand, dust, dirt, and other substances can significantly degrade optical signals. For many obscurants, the index of refraction is dependent on the wavelength of light, and there exists a Christiansen wavelength (λc) at which scattering is at a minimum. At λc the index of refraction of the scattering particles (ns) matches that of the surrounding medium, in this case air (with refractive index na). This condition makes the scattering particulates almost invisible to the propagating light, minimizing scattering and increasing transmission at λc. Previously, the authors showed a technique for measuring the index of refraction n(λ) and the extinction coefficient k(λ) using spectroscopic ellipsometry for various sand samples. Spectroscopic measurements on static sand samples demonstrated good agreement with the predicted spectral properties and highlighted the presence of a Christiansen feature near 8 µm. However, in outdoor environments, the scattering particles are never stationary but in a constant state of motion. In this work, spectroscopic measurements on dynamic sand samples (sand that is falling through the optical beam path) show two Christiansen features seen previously in predicted and observed static sand measurements. Additionally, we characterize, for the first time, transmission around a Christiansen feature using a tunable laser and show results consistent with other spectroscopic measurements.

Measurement of the Optical Constants of Sand Samples Using Ellipsometry on Sand-Adhesive Composites.

In order to model the propagation of light through a sand cloud, it is critical to have accurate data for the optical constants of the sand particles that comprise it. The same holds true for modeling propagation through particles of any type suspended in a medium. Few methods exist, however, to measure these quantities with high accuracy. In this paper, a characterization method based on spectroscopic ellipsometry (SE) that can be applied to a particulate material is presented. In this method, a polished disc of an adhesive compound is prepared, and its optical constants are measured. Next, a mixture of the adhesive and a sand sample is prepared and processed into a polished disc, and SE is performed. By treating the mixture as a Bruggeman effective medium, the optical constants of the particulate material are extracted. For verification of the proposed method, it is first applied to pure silica powder, demonstrating good agreement between measured optical constants and literature values. It is then applied to Arizona road dust, a standard reference material, as well as real desert sand samples. The resulting optical constant data is input into a rigorous scattering model to predict extinction coefficients for various types of sand. Modeling results are compared to spectroscopic measurements on static sand samples, demonstrating good agreement between predicted and measured spectral properties including the presence of a Christiansen feature near a wavelength of 8 µm.

All fiber watt-level fiber source at 760†nm generated through four-wave mixing in a photonic crystal fiber.

There are limited fiber-based single-mode laser sources over the visible and near infrared range. Nonlinear conversion through four-wave mixing in photonic crystal fibers allows for the generation of new wavelengths far from a pump wavelength. Utilizing an all-fiber spliced configuration, we convert 1064 nm light into a W-level signal in the 750 nm - 820 nm spectral region. We demonstrate over 7.9 watts in the signal band, out of a custom photonic crystal fiber with M2 < 1.15. The input peak power as well as fiber length can be selected to keep the converted power in a 0.6 nm narrow emission band or broaden the output to 45 nm spectral band with spectral density greater than 50 mW/nm by pumping with higher peak powers.

Spectral Considerations for Standoff Infrared Detection of RDX on Reflective Aluminum.

This paper examines infrared spectroscopic effects for the standoff detection of an explosive material, hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), inkjet printed on an aluminum surface. Results of a spectroscopic study are described, using multiple optical setups. These setups were selected to explore how variations in the angles of incidence and collection from the surface of the material result in corresponding variations in the spectral signatures. The goal of these studies is to provide an understanding of these spectral changes since it affects standoff detection of hazardous materials on a reflective substrate. We demonstrate that variations in spectral effects are dependent on the relative surface concentration of the deposited RDX. We also show that it is reasonable to use spectroscopic data collected in a standard laboratory infrared spectrometer outfitted with a variable angle reflectometer set at 0° as reference spectra for data collected in a standoff configuration. These results are important to provide a systematic approach to understanding infrared (IR) spectra collection using standoff systems in the field, and to allow for comparison between such data, and data collected in the laboratory. Although the precise results are constrained to a specific material system (thin layers on a reflective substrate), the approach and general discussion provided are applicable to a broad range of IR standoff sensing techniques and applications.

Thermal tuning of arsenic selenide glass thin films and devices.

We present a method of post-deposition tuning of the optical properties of thin film dielectric filters and mirrors containing chalcogenide glass (ChG) layers by thermally adjusting their refractive index. A common challenge associated with the use of ChG films in practical applications is that they suffer from slight run-to-run variations in optical properties resulting from hard-to-control changes in source material and deposition conditions. These variations lead to inconsistencies in optical constants, making the fabrication of devices with prescribed optical properties challenging. In this paper, we present new work that takes advantage of the large variation of a ChG films' refractive index as a function of annealing. We have carried out extensive characterization of the thermal index tuning and thickness change of arsenic selenide (As2Se3) ChG thin films and observed refractive index changes larger than 0.1 in some cases. We show results for refractive index as a function of annealing time and temperature and propose a model to describe this behavior based on bond rearrangement. We apply thermal refractive index tuning to permanently shift the resonance of a Fabry-Perot filter and the cutoff wavelength of a Bragg reflector. The Bragg reflector, consisting of alternating As2Se3 and CaF2 layers, exhibits high reflectance across a ∼550 nm band with only five layers. Modeling results are compared with spectroscopic measurements, demonstrating good agreement.

Efficient extraction of high pulse energy from partly quenched highly Er3+-doped fiber amplifiers.

We demonstrate efficient pulse-energy extraction from a partly quenched erbium-doped aluminosilicate fiber amplifier. This has a high erbium concentration that allows for short devices with reduced nonlinear distortions but also results in partial quenching and thus significant unsaturable absorption, even though the fiber is still able to amplify. Although the quenching degrades the average-power efficiency, the pulse energy remains high, and our results point to an increasingly promising outcome for short pulses. Furthermore, unlike unquenched fibers, the conversion efficiency improves at low repetition rates, which we attribute to smaller relative energy loss to quenched ions at higher pulse energy. A short (2.6 m) cladding-pumped partly quenched Er-doped fiber with 95-dB/m 1530-nm peak absorption and saturation energy estimated to 85 µJ reached 0.8 mJ of output energy when seeded by 0.2-µs, 23-µJ pulses. Thus, according to our results, pulses can be amplified to high energy in short highly Er-doped fibers designed to reduce nonlinear distortions at the expense of average-power efficiency.

Behavior of the Reststrahlen Band in the 17-25 µm Spectral Region in the Diffuse Reflection Spectra of Sand and Silt Mixtures.

Studies on the reflectance spectra of different mixtures of sand and silt were performed in the infrared spectral region of 7-25 µm to explore the behavior of a second reststrahlen band occurring between 17 and 25 µm with respect to different mixtures of sand and silt. The reflectance spectrum of all samples exhibited reststrahlen bands within both the long wavelength infrared (LWIR) and the very long wavelength infrared (VLWIR) regions of the reflectance spectrum. Results demonstrate that both LWIR and VLWIR reststrahlen bands increase in area as the fraction of sand increases to 80%. More importantly, the data demonstrate that the VLWIR reststrahlen band, like that in LWIR, exhibits a significant and reproducible decrease in reflectivity for mixed soil versus weathered soil.

Demonstration of a Human Color Vision Mimic in the Infrared.

Color vision results from the interaction of retinal photopigments with reflected or transmitted visible light. The International Commission on Illumination (CIE) developed the CIE color-matching chart, which separates colors on the basis of the interaction of their spectral profiles with three retinal photopigments in the human eye. We report the development of an infrared chromaticity (CIE-IR) chart, which mimics the CIE chart, in order to discriminate between different chemicals on the basis of the interactions of their IR signatures with three different IR optical filters, instead of the retinal photopigments in the human eye. Our results demonstrate that the CIE-IR chart enables separation of different classes of chemicals, as the visible CIE chart does with color, except for those in the IR spectral region. Such results clearly show that the biomimetic sensing method based on human color vision is in fact a true analogue to color vision and that the proposed CIE-IR chart can be used as a classification method unique to this biomimetic sensing modality.

Discrimination Between Explosive Materials and Isomers Using a Human Color Vision-Inspired Sensing Method.

This paper describes the application of a human color vision approach to infrared (IR) chemical sensing for the discrimination between multiple explosive materials deposited on aluminum substrates. This methodology classifies chemicals using the unique response of the chemical vibrational absorption bands to three broadband overlapping IR optical filters. For this effort, Fourier transform infrared (FT-IR) spectroscopy is first used to computationally examine the ability of the human color vision sensing approach to discriminate between three similar explosive materials, 1,3,5,-Trinitro-1,3,5-triazinane (RDX), 2,2-Bis[(nitrooxy)methyl]propane-1,3,-diyldinitrate (PETN), and 1,3,5,7-Tetranitro-1,3,5,7-tetrazocane (HMX). A description of a laboratory breadboard optical sensor designed for this approach is then provided, along with the discrimination results collected for these samples using this sensor. The results of these studies demonstrate that the human color vision approach is capable of high-confidence discrimination of the examined explosive materials.

Infrared Reflectance Spectroscopic Evaluation of Inkjet Printed Standards of Cyclotrimethylenetrinitramine (RDX) on Aluminum Substrates.

The Department of Defense (DOD) and first responder communities are evaluating and developing optical systems for the detection and identification of explosives and components used for assembling homemade explosives (HMEs). Emerging detection technologies must be evaluated with authentic hazard material concentrations to ensure their accurate and reliable use in the field. In this work, infrared (IR) reflectance spectra over the spectral rage of 1000-1700 cm-1 were collected for different concentrations of inkjet-printed RDX (cyclotrimethylenetrinitramine) samples deposited onto aluminum substrates. A plot of the integrated area of both the symmetric and asymmetric NO2 vibrational bands for RDX on aluminum exhibited good linearity over the concentration range 20-500 µg/cm2. Detection limits for RDX on an aluminum surface were calculated to be 10.7 µg/cm2 for the symmetric NO2 vibrational band and 1.4 µg/cm2 for the asymmetric NO2 vibrational band. Evaluation of the NO2 vibrational band areas at different locations of the RDX array demonstrated that the samples exhibited good homogeneity across the surface. The concentration of an unknown sample of RDX on aluminum was determined using the fitted equations; results showed good agreement between the calculated and actual RDX surface concentration. The lot-to-lot variation of RDX on the aluminum surface was compared using the long wavelength infrared (LWIR) spectral band areas for two different lots of standards printed at the same RDX surface concentration. Results showed excellent lot-to-lot agreement indicating good reproducibility of the standards for RDX.

Optical Properties of a Sulfur-Rich Organically Modified Chalcogenide Polymer Synthesized via Inverse Vulcanization and Containing an Organometallic Comonomer.

Inverse vulcanization is the method by which molten sulfur can be combined with comonomers to form stable polymers termed "organically modified chalcogenide" or "ORMOCHALC" polymers. One advantage to ORMOCHALC polymers is that they can possess important optical properties, such as high refractive index and strong infrared (IR) transmission, while being easier to fabricate than glass materials with similar optical properties. In the present work, a new ORMOCHALC is fabricated by using tetravinyltin as a comomoner with sulfur. This is the first example of an organometallic molecule being used as a comonomer to develop ORMOCHALCs. The result is an ORMOCHALC polymer that has the highest refractive index reported for a "sulfur and comonomer" polymer and that demonstrates unprecedented transmission in the IR region.

Analytical procedure to assess the performance characteristics of a non-spectroscopic infrared optical sensor for discrimination of chemical vapors.

An optical-filter-based sensor that was designed to mimic human color vision was recently developed. This sensor uses three mid-infrared optical filters to discriminate between chemicals with similar, strongly overlapping mid-infrared absorption bands. This non-spectroscopic technique requires no spectral scanning. This paper defines the selectivity and specificity of this biomimetic sensor. Receiver operating characteristic curves are presented for each target chemical. These results demonstrate that the sensor is highly selective and can provide discrimination with no false positives for three similar target chemicals-acetone, hexane, and fuel oil-while rejecting potential interferents.

Reconfiguring structured light beams using nonlinear metasurfaces.

Ultra-compact, low-loss, fast, and reconfigurable optical components, enabling manipulation of light by light, could open numerous opportunities for controlling light on the nanoscale. Nanostructured all-dielectric metasurfaces have been shown to enable extensive control of amplitude and phase of light in the linear optical regime. Among other functionalities, they offer unique opportunities for shaping the wave front of light to introduce the orbital angular momentum (OAM) to a beam. Such structured light beams bring a new degree of freedom for applications ranging from spectroscopy and micromanipulation to classical and quantum optical communications. To date, reconfigurability or tuning of the optical properties of all-dielectric metasurfaces have been achieved mechanically, thermally, electrically or optically, using phase-change or nonlinear optical materials. However, a majority of demonstrated tuning approaches are either slow or require high optical powers. Arsenic trisulfide (As2S3) chalcogenide glass offering ultra-fast and large χ(3)nonlinearity as well as a low two-photon absorption coefficient in the near and mid-wave infrared spectral range, could provide a new platform for the realization of fast and relatively low intensity reconfigurable metasurfaces. Here, we design and experimentally demonstrate an As2S3 chalcogenide glass based metasurface that enables reshaping of a conventional Hermite-Gaussian beam with no OAM into an OAM beam at low intensity levels, while preserves the original beam's amplitude and phase characteristics at high intensity levels. The proposed metasurface could find applications for a new generation of optical communication systems and optical signal processing.

Nanoparticle doping for high power fiber lasers at eye-safer wavelengths.

A nanoparticle (NP) doping technique was developed for fabricating erbium (Er)- and holmium (Ho)-doped silica-based optical fibers for high energy lasers. Slope efficiencies in excess of 74% were realized for Er NP doping in a single mode fiber based master oscillator power amplifier (MOPA) and 53% with multi-Watt-level output in a resonantly cladding-pumped power oscillator laser configuration based on a double-clad fiber. Cores comprising Ho doped LaF3 and Lu2O3 nanoparticles exhibited slope efficiencies as high as 85% at 2.09 µm in a laser configuration. To the best of the authors' knowledge, this is the first report of a holmium nanoparticle doped fiber laser as well as the highest efficiency and power output reported from an erbium nanoparticle doped fiber laser.

Biomimetic Optical-Filter Detection System for Discrimination of Infrared Chemical Signatures.

Optical-filter-based chemical sensors have the potential to dramatically alter the field of hazardous materials sensing. Such devices could be constructed using inexpensive components, in a small and lightweight package, for sensing hazardous chemicals in defense, industrial, and environmental applications. Filter-based sensors can be designed to mimic human color vision. Recent developments in this field have used this approach to discriminate between strongly overlapping chemical signatures in the mid-infrared. Reported work relied on using numerically filtered FTIR spectra to model the infrared biomimetic detection methodology. While these findings are encouraging, further advancement of this technique requires the collection and evaluation of directly filtered data, using an optical system without extensive numerical spectral analysis. The present work describes the design and testing of an infrared optical breadboard system that uses the biomimetic mammalian color-detection approach to chemical sensing. The set of chemicals tested includes one target chemical, fuel oil, along with two strongly overlapping interferents, acetone and hexane. The collected experimental results are compared with numerically filtered FTIR spectral data. The results show good agreement between the numerically filtered data model and the data collected using the optical breadboard system. It is shown that the optical breadboard system is operating as expected based on modeling and can be used for sensing and discriminating between chemicals with strongly overlapping absorption bands in the mid-infrared.

Infrared glass-based negative-curvature anti-resonant fibers fabricated through extrusion.

Negative curvature fibers have been gaining attention as fibers for high power infrared light. Currently, these fibers have been made of silica glass and infrared glasses solely through stack and draw. Infrared glasses' lower softening point presents the opportunity to perform low-temperature processing methods such as direct extrusion of pre-forms. We demonstrate an infrared-glass based negative curvature fiber fabricated through extrusion. The fiber shows record low losses in 9.75 - 10.5 µm range (which overlaps with the CO2 emission bands). We show the fiber's lowest order mode and measure the numerical aperture in the longwave infrared transmission band. The possibility to directly extrude a negative curvature fiber with no penalties in losses is a strong motivation to think beyond the limitations of stack-and-draw to novel shapes for negative curvature fibers.

Fabrication tolerances in As2S3 negative-curvature antiresonant fibers.

We computationally investigate fabrication tolerances in As2S3 negative-curvature antiresonant tube-lattice fibers. Since the dominant loss mechanisms for silica in the mid-infrared (mid-IR) is material absorption, As2S3, which offers a reduced loss over that wavelength range, is a natural candidate for mid-IR antiresonant fibers. However, any fiber fabrication technology, including for soft glasses, will have imperfections. Therefore, it is important to know how imperfect fabrication will affect the results of a fiber design. We study perturbations to the fiber, including a nonconstant tube-wall thickness, a single cladding tube with a different radius, a single cladding tube with a different tube-wall thickness, and "key" sections in the jacket.

Overview of transparent optical ceramics for high-energy lasers at NRL.

In this review, we present our recent research progress at the Naval Research Laboratory in the development of highly transparent and rugged ceramic window materials such as MgAl2O4 spinel and ß-SiC; high-power solid-state laser gain materials based on sesquioxide such as Yb(3+):Y2O3, Yb(3+):Lu2O3, and Ho(3+):Lu2O3; and composite ceramics in the application for high-energy lasers. Various powder synthesis/purification methods and powder post-process techniques necessary to create high-purity powders are described. Ceramic fabrication processes and chemical, morphological, and optical properties of the ceramics developed at the Naval Research Laboratory (NRL) are highlighted. We also report high-efficiency lasing from a hot-pressed rare-earth sesquioxide single layer and composite ceramics made from coprecipitated powder.

Review of infrared fiber-based components.

The infrared range of the optical spectrum is attractive for its use in sensing, surveillance, and material characterization. The increasing availability of compact laser sources and detectors in the infrared range stands in contrast with the limited development of optical components for this optical range. We highlight developments of infrared components with a particular focus on fiber-based components for compact optical devices and systems.

Review of antireflective surface structures on laser optics and windows.

We present recent advancements in structured, antireflective surfaces on optics, including crystals for high-energy lasers as well as windows for the infrared wavelength region. These structured surfaces have been characterized and show high transmission and laser damage thresholds, making them attractive for these applications. We also present successful tests of windows with antireflective surfaces that were exposed to simulated harsh environments for the application of these laser systems.